Driver update problems with GTX 760

Hi all,
I have PC with Intel DH87MC MB, i7-4770 CPU and MSI N760 TF 2GD5/OC video card installed. Samsung P2350 monitor is connected via DVI.
When I first installed it, I got newest drivers for video card (320.49) at this time and everything was working ok. Later I got notifications about new drivers and there my troubles started. Every time I try update driver to newer one (334.89 for example), my display goes off during installation process and never comes back on. I have to turn off my PC, start it in safe mode, uninstall driver, boot to windows and install that 320.49 driver again. I've updated MB BIOS and drivers, but situation is same every time.
What to try next?
Thanks,
Zebediejus

Hi, sorry for late answer. This doesn't work too. I tried uninstall from safe mode, even deleted folders from program files. After installing new drivers (335.23) and reboot, got same problem - monitor goes off while windows are booting.
After this tried other way - again uninstalled everything from safe mode, booted in normal mode, installed old drivers (320.49) from DVD, rebooted - everything is working fine. Then I tried to "update" existing drivers with downloaded ones. Immediately after "Installing graphics driver..." message is shown, screen goes off, but installation continues (I see it by blinking HDD activity led). After reboot monitor is staying off until I remove drivers from safe mode. So, now I am back on 320.49 from my DVD. Any other suggestions where problem can be?
Thanks,
Zebediejus

Similar Messages

Printer: Driver Update Problem with HP 6700 All In One Printer

My HP 6700 All in One Printer is not set up correctly on my laptop (16 months old),. I need to update the Driver but the auo system says the driver can not be found, when I try to do in manually it loads onto my lap top but does not update the printer. Any suggestions?

Hi,
I request you to try the following:
For network connection:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03086294&tmp_task=useCategory&cc=us&dlc=en&lc=e...
For USB:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03521864&tmp_task=useCategory&cc=us&dlc=en&lc=e...
Although I am an HP employee, I am speaking for myself and not for HP.
Say thanks by clicking the "
Kudos! Thumps Up" which is on the right
Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue
Regards,
Ray

[REQUEST] GOP/UEFI BIOS Update for MSI GTX 760 HAWK

Hello,
I'd like to request a GOP/UEFI bios update for MSI GTX 760 HAWK 2GB
SN: 602-V300-01SB1307104617
https: //drive.google.com/file/d/0B1-fBAUWkbq0MjAzbWM3Z3laUk0/view?usp=sharing
Thanks!

Quote from: livanu.razvan on 18-December-14, 05:21:18
Is there a tutorial on how to flash the new BIOS?
Decompress the provided .rar archive with Winrar: http://www.rarlab.com/download.htm
Then flash the desired file included with Nvflash for dos: http://www.guru3d.com/files_details/nvflash_download.html
To do so rename the included file to .rom and create a dos bootstick (https://forum-en.msi.com/index.php?topic=165175.0)
Put nvflash and the vbios file on it and boot from the stick. Then type nvflash -4 -5 -6 gop.rom (if renamed vbios that way) and hit enter. Confirm the questions and let the tool flash.
Quote from: livanu.razvan on 18-December-14, 05:21:18
Also, what is the difference between normal and ln2, or witch one is safe to use?
normal is the pre-overclocked default vbios. LN2 (which can be chosen via the selector switch on top of your card) is not factory overclocked but allows more extreme manual oc without the limits of normal vbios (more voltage and power draw allowed). This is especially needed for extreme oc like if using Liquid nitrogen (LN2) cooling for oc records.

Im trying to update, but all it does is backup my phone, My itunes is updated, BTW, I just went to Apple bar, i had previous problem with prior phone, now im having this update problem with thyis new phone, someone HELP!!

Im trying to update, but all it does is backup my phone, My itunes is updated, BTW, I just went to Apple bar, i had previous problem with prior phone, now im having this update problem with thyis new phone, someone HELP!!

Same here and this is driving me crazy. I can buy, but can't upgrade. Grrr.

Latest iTunes update problems with repeated error messages every 65 seconds??

After this mornings' update of iTunes. Problems with Applemobiledeviceservices.exe. Error message every 65 seconds - software exception (oxc06d007e) occurred in the application at location 0x7c812fd3.
How do I stop this?

'The installer has insufficient privileges to modify this file C:\Program Files (x86)\Common Files\Apple\Apple Application Support\Web kit.resources\inspector\Images\Spinner Inactive Selected.gif.'
That one's consistent with disk/file damage. The first thing I'd try with that is running a disk check (chkdsk) over your C drive.
XP instructions in the following document: How to perform disk error checking in Windows XP
Vista instructions in the following document: Check your hard disk for errors
Windows 7 instructions in the following document: How to use CHKDSK (Check Disk)
Select both Automatically fix file system errors and Scan for and attempt recovery of bad sectors, or use chkdsk /r (depending on which way you decide to go about doing this). You'll almost certainly have to schedule the chkdsk to run on startup. The scan should take quite a while ... if it quits after a few minutes or seconds, something's interfering with the scan.
Does the chkdsk find/repair any damage? If so, can you get an install to go through properly afterwards?

Intel HD Graphics 4400 driver update problem.

Hi!
I have an Inspiron 3537 157813. I tried to update to the recommended driver (10.18.10.3316, A02), downloaded from DELL Support, for Intel HD Graphics 4400. But it shows an error message: "The driver being installed is not validated for this computer. Please obtain the appropriate driver from the computer manufacturer."
What could I do?

sorry I do not have an answer, I do have the same problem with this graphics and noticed you had no reply so I thought if I add to it we might get a response from Dell or someone in the forum. I cannot update intel 4400 it is stuck with 10.18.10.3282 (26/08/2013) it won't update to the latest iris even though it goes through the full installation without error, it's the same with any previous update since the one installed, there is always issues with either intel 4400 or AMD 8870m dedicated, any update after 2013 and the AMD is recognised as R9 M270X which it clearly isn't , it doesn't matter if I download the graphics drivers from here or from Intel website itself it just doesn't update, updated chipset and bios and all other hardware and software updates ok Intel 4400 just stays at version 10.18.10.3282, any info would be appreciated ... cheers
F8ally

Satellite L670-1KZ - driver update & issue with ARMA II game

Hi everybody,
I just bought this satellite L670-1KZ in France, and I already found fews updates.
But, before doing anything I wish to have comment and recommandation from others owners, to make sure the files I have in hand are useful and will not damaged anything (never know).
1) UPDATE RECOMMANDED OR NOT ?
This is the list of the update I found :
Ati Radeon Mobility HD 2000/3000/4000/5000/6000 version 11.3 WHQL
Fabricant : ATI Technologies Inc.
Version : 8.831.2.0000
Nom du fichier inf : c7115930.inf
Date du fichier inf : 08/03/2011
Date de publication (mise en ligne) : 30/03/2011
Realtek Pilote High Definition Audio version R2.57 WHQL
Fabricant : Realtek Semiconductor Corp.
Version : 6.0.1.6299
Nom du fichier inf : hdapcee3.inf
Date du fichier inf : 25/01/2011
Date de publication (mise en ligne) : 09/02/2011
Realtek RTL8100/8101/8102/8103/8105/8401/8110/8111/8168/8169 version 7.037.1229.2010 WHQL
Fabricant : Realtek
Version : 7.037.1229.2010
Nom du fichier inf : rt64win7.inf
Date du fichier inf : 29/12/2010
Date de publication (mise en ligne) : 09/02/2011
Realtek RTL8191SE-VA2/RTL8192SE version 2019.1.1203.2010 WHQL
Fabricant : Realtek Semiconductor Corp.
Version : 2019.1.1203.2010
Nom du fichier inf : net8192se.inf
Date du fichier inf : 03/12/2010
Date de publication (mise en ligne) : 09/02/2011
Intel Chipset Device Software version 9.2.0.1025 WHQL
Fabricant : Intel
Version : 7.0.0.1013
Nom du fichier inf : ibexahci.inf
Date du fichier inf : 08/06/2010
Date de publication (mise en ligne) : 09/03/2011
Intel Rapid Storage Technology ICH7/ICH8/ICH9/ICH10/PCH version 10.1.0.1008 WHQL
Fabricant : Intel
Version : 10.1.0.1008
Nom du fichier inf : iaahci.inf
Date du fichier inf : 06/11/2010
Date de publication (mise en ligne) : 21/12/2010
2) ABOUT THE VIDEO CARD :
Also, before I had a Amilo Xi 2550-8009 that melt last week, I changed it for this Toshiba, but I am facing a problem with a game ARMA II.
The error message I got is : "Error compiling pixel shader", with black screen and a "ping" noise.
I don't understand because I found a comparative test with a GeForce and my current HD5650 that is supposed to support this shader stuff.
Did you manage to run ARMA II on your laptop ? If yes, what did I miss ?
Thanks in advance for your feedback fully appreciated,
G2MARS

Hi Syntax,
yes agree, you're so right, I just got 3BDO within 20 minutes today, still trying to understand why.
Signature du problme*:
Nom dvnement de problme: BlueScreen
Version du systme: 6.1.7601.2.1.0.768.3
Identificateur de paramtres rgionaux: 1036
Informations supplmentaires sur le problme*:
BCCode: d1
BCP1: 0000000000000028
BCP2: 0000000000000002
BCP3: 0000000000000000
BCP4: FFFFF8800176EB2D
OS Version: 6_1_7601
Service Pack: 1_0
Product: 768_1
It might come from those damned update I did.... The last one is about the video card on the pilot update through driver device, right click, update.
I was surprised he did it, but, I suspect I had a BDO before that, can't remember.
Then... Still trying to identify the reason, I might go back to the older pilot version.
About Arma 2,on the very good website "Can I run it" it said there was a problem with the video card
Video Card
Recommended: NVIDIA GeForce 8800 GT / ATI Radeon HD 4850 with Shader Model 3 and 512 MB VRAM or faster
You Have: ATI Mobility Radeon HD 5650
Upgrade Suggested: Unfortunately, your Video Card does not meet this requirement. In the other hand I found this website with a test that compared the HD5650 with a GeForce, they said :
"La Mobility Radeon HD 5650 se montre ici bien plus performante que le GeForce GT 420M qui se relgu la dernire place par le GT 330M, plus performant sur ce jeu galement."
The HD5650 is more performant than the GeForce GT 420M .... If you understand something let me know cause I don't !
[TEST ATI and GEFORCE|http://www.clubic.com/carte-graphique/carte-graphique-nvidia/geforce-400-series/article-363820-3-test-nvidia-geforce-gt-420m.html]
Amazing, because this game ran on my Amilo xi 2550-8009 and a ATI Radeon HD 2700 256 Mo.
And Arma II Operation Arrowhead didn't show this error message, but, didn't run so well even with low graphic option,I just downloaded a ultimate patch v1.59, to be followed.

HP Universal Print Driver (UPD) problem with tcp/ip port

Hi,
We are facing, since few days, problems with HP UPD in windows 7. Let me explain.
For some reasons we need the auto update feature of HP UPD, but this feature does not works anymore.
We found that, when installing a printer, if we name the tcp/ip port with the dns name or ip the auto-update will work, but if we name the TCP/IP port with dummy text, the auto update feature won't work (can't connect to the printer). This is like the UPD
try to resolve the tcp/ip port name instead of tcp/ip port address.
This was working last month. We installed some windows updates on clients, and one of these updates screwed up the UPD. I have the list of installed updates but there are many, and if someone already had this problem and can help it would be nice. And if
nobody can help, maybe this message will put other poeple with the same problem on the way to solution.
We don't want to update the driver (too much printers involved, too much clients also)
Thx for reading and helping !

Hello SNoof,
What is your current situation?
About Troubleshoot problems with removing updates, please take a look at the following article.
http://windows.microsoft.com/en-hk/windows/troubleshoot-problems-removing-updates#1TC=windows-7
1.Open Installed Updates by clicking the Start button, clicking Control Panel, clicking Programs, and then, under Programs and Features, clicking View installed updates.
2.Select the update that you want to remove, and then click Uninstall. Administrator permission required If you're prompted for an administrator password or confirmation, type the password or provide confirmation.
Best regards,
Fangzhou CHEN
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Update problems with itunes 10.6.1 on xp

When I try to update to iTunes 10.6.1 n Windows XP sp3 I get the dialog box to repair or remove. If I select repair the update fails. Any ideas on how to correct this issue?

I have an old macbook too.
It seems like Apple writes new software that makes older computers not work as well.
I always have reservations about updating with an older model.
Does anybody else have any problems with the new iTunes?
Model Name:          MacBook
Model Identifier:          MacBook4,1
Processor Name:          Intel Core 2 Duo
Processor Speed:          2.4 GHz
Number Of Processors:          1
Total Number Of Cores:          2
L2 Cache:          3 MB
Memory:          2 GB
Bus Speed:          800 MHz
Boot ROM Version:          MB41.00C1.B00
SMC Version (system):          1.31f1
Serial Number (system):
Hardware UUID:
Sudden Motion Sensor:
State:          Enabled

Arch64 ati radeon 3870 radeonhd driver. Problem with xorg.conf.

I've got a small problem with my xorg. I won't hide that i'm not a xorg nerd and i've used the automatic xorg tool to generate the xorg.conf. After starting X, the screen goes black and then after ~5 seconds montior switches to power-saving mode.
So here we go.
That's xorg.conf
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
Screen 1 "Screen1" RightOf "Screen0"
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/TTF"
FontPath "/usr/share/fonts/Type1"
EndSection
Section "Module"
Load "glx"
Load "extmod"
Load "record"
Load "dri2"
Load "dbe"
Load "dri"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Monitor"
Identifier "Monitor1"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "NoAccel" # [<bool>]
#Option "AccelMethod" # [<str>]
#Option "offscreensize" # [<str>]
#Option "SWcursor" # [<bool>]
#Option "ignoreconnector" # [<str>]
#Option "forcereduced" # [<bool>]
#Option "forcedpi" # <i>
#Option "useconfiguredmonitor" # [<bool>]
#Option "HPD" # <str>
#Option "NoRandr" # [<bool>]
#Option "RROutputOrder" # [<str>]
#Option "DRI" # [<bool>]
#Option "TVMode" # [<str>]
#Option "ScaleType" # [<str>]
#Option "UseAtomBIOS" # [<bool>]
#Option "AtomBIOS" # [<str>]
#Option "UnverifiedFeatures" # [<bool>]
#Option "Audio" # [<bool>]
#Option "HDMI" # [<str>]
#Option "COHERENT" # [<str>]
Identifier "Card0"
Driver "radeonhd"
VendorName "ATI Technologies Inc"
BoardName "Radeon HD 3870"
BusID "PCI:1:0:0"
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "NoAccel" # [<bool>]
#Option "AccelMethod" # [<str>]
#Option "offscreensize" # [<str>]
#Option "SWcursor" # [<bool>]
#Option "ignoreconnector" # [<str>]
#Option "forcereduced" # [<bool>]
#Option "forcedpi" # <i>
#Option "useconfiguredmonitor" # [<bool>]
#Option "HPD" # <str>
#Option "NoRandr" # [<bool>]
#Option "RROutputOrder" # [<str>]
#Option "DRI" # [<bool>]
#Option "TVMode" # [<str>]
#Option "ScaleType" # [<str>]
#Option "UseAtomBIOS" # [<bool>]
#Option "AtomBIOS" # [<str>]
#Option "UnverifiedFeatures" # [<bool>]
#Option "Audio" # [<bool>]
#Option "HDMI" # [<str>]
#Option "COHERENT" # [<str>]
Identifier "Card1"
Driver "radeonhd"
VendorName "ATI Technologies Inc"
BoardName "Radeon HD 3870"
BusID "PCI:2:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Section "Screen"
Identifier "Screen1"
Device "Card1"
Monitor "Monitor1"
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
and that's the log
This is a pre-release version of the X server from The X.Org Foundation.
It is not supported in any way.
Bugs may be filed in the bugzilla at http://bugs.freedesktop.org/.
Select the "xorg" product for bugs you find in this release.
Before reporting bugs in pre-release versions please check the
latest version in the X.Org Foundation git repository.
See http://wiki.x.org/wiki/GitPage for git access instructions.
X.Org X Server 1.6.3.901 (1.6.4 RC 1)
Release Date: 2009-8-25
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.30-ARCH x86_64
Current Operating System: Linux kasia 2.6.31-ARCH #1 SMP PREEMPT Tue Oct 13 11:33:39 CEST 2009 x86_64
Build Date: 04 September 2009 05:45:43PM
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Wed Oct 21 20:31:45 2009
(++) Using config file: "xorg.conf.new"
(==) ServerLayout "X.org Configured"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "Monitor0"
(**) | |-->Device "Card0"
(**) |-->Screen "Screen1" (1)
(**) | |-->Monitor "Monitor1"
(**) | |-->Device "Card1"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Keyboard0"
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/TTF" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/Type1" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/TTF" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/Type1" does not exist.
Entry deleted from font path.
(**) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
built-ins
(**) ModulePath set to "/usr/lib/xorg/modules"
(WW) AllowEmptyInput is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
(WW) Disabling Mouse0
(WW) Disabling Keyboard0
(II) Loader magic: 0x1d40
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 5.0
X.Org XInput driver : 4.0
X.Org Server Extension : 2.0
(II) Loader running on linux
(--) using VT number 7
(!!) More than one possible primary device found
(--) PCI: (0:1:0:0) 1002:9501:1458:21a4 ATI Technologies Inc Radeon HD 3870 rev 0, Mem @ 0xd0000000/268435456, 0xf7000000/65536, I/O @ 0x0000a000/256, BIOS @ 0x????????/131072
(--) PCI: (0:2:0:0) 1002:9501:1458:21a4 ATI Technologies Inc Radeon HD 3870 rev 0, Mem @ 0xe0000000/268435456, 0xf5000000/65536, I/O @ 0x0000b000/256, BIOS @ 0x????????/131072
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) System resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
(II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
(II) "glx" will be loaded. This was enabled by default and also specified in the config file.
(II) "record" will be loaded. This was enabled by default and also specified in the config file.
(II) "dri" will be loaded. This was enabled by default and also specified in the config file.
(II) "dri2" will be loaded. This was enabled by default and also specified in the config file.
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.6.3.901, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.6.3.901, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.6.3.901, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions//libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.6.3.901, module version = 1.1.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.6.3.901, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.6.3.901, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "radeonhd"
(II) Loading /usr/lib/xorg/modules/drivers//radeonhd_drv.so
(II) Module radeonhd: vendor="AMD GPG"
compiled for 1.6.0, module version = 1.2.5
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 5.0
(II) RADEONHD: X driver for the following AMD GPG (ATI) graphics devices:
RV505 : Radeon X1550, X1550 64bit.
RV515 : Radeon X1300, X1550, X1600; FireGL V3300, V3350.
RV516 : Radeon X1300, X1550, X1550 64-bit, X1600; FireMV 2250.
R520 : Radeon X1800; FireGL V5300, V7200, V7300, V7350.
RV530 : Radeon X1300 XT, X1600, X1600 Pro, X1650; FireGL V3400, V5200.
RV535 : Radeon X1300, X1650.
RV550 : Radeon X2300 HD.
RV560 : Radeon X1650.
RV570 : Radeon X1950, X1950 GT; FireGL V7400.
R580 : Radeon X1900, X1950; AMD Stream Processor.
R600 : Radeon HD 2900 GT/Pro/XT; FireGL V7600/V8600/V8650.
RV610 : Radeon HD 2350, HD 2400 Pro/XT, HD 2400 Pro AGP; FireGL V4000.
RV620 : Radeon HD 3450, HD 3470.
RV630 : Radeon HD 2600 LE/Pro/XT, HD 2600 Pro/XT AGP; Gemini RV630;
FireGL V3600/V5600.
RV635 : Radeon HD 3650, HD 3670.
RV670 : Radeon HD 3690, 3850, HD 3870, FireGL V7700, FireStream 9170.
R680 : Radeon HD 3870 X2.
M52 : Mobility Radeon X1300.
M54 : Mobility Radeon X1400; M54-GL.
M56 : Mobility Radeon X1600; Mobility FireGL V5200.
M58 : Mobility Radeon X1800, X1800 XT; Mobility FireGL V7100, V7200.
M62 : Mobility Radeon X1350.
M64 : Mobility Radeon X1450, X2300.
M66 : Mobility Radeon X1700, X1700 XT; FireGL V5250.
M68 : Mobility Radeon X1900.
M71 : Mobility Radeon HD 2300.
M72 : Mobility Radeon HD 2400; Radeon E2400.
M74 : Mobility Radeon HD 2400 XT.
M76 : Mobility Radeon HD 2600;
(Gemini ATI) Mobility Radeon HD 2600 XT.
M82 : Mobility Radeon HD 3400.
M86 : Mobility Radeon HD 3650, HD 3670, Mobility FireGL V5700.
M88 : Mobility Radeon HD 3850, HD 3850 X2, HD 3870, HD3870 X2.
RS600 : Radeon Xpress 1200, Xpress 1250.
RS690 : Radeon X1200, X1250, X1270.
RS740 : RS740, RS740M.
RS780 : Radeon HD 3100/3200/3300 Series.
RV770 : Radeon HD 4800 Series; Everest, K2, Denali ATI FirePro.
R700 : Radeon R700.
M98 : Radeon M98 Mobility.
RV730 : Radeon HD4670, HD4650.
M96 : Radeon M96 Mobility.
RV710 : Radeon HD4570, HD4350.
(II) RADEONHD: version 1.2.5, built from dist of git branch master, commit cb54f48b
(II) Primary Device is:
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) resource ranges after probing:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b]
[5] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b]
[6] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b]
[7] 1 0 0x000a0000 - 0x000affff (0x10000) MS[b]
[8] 1 0 0x000b0000 - 0x000b7fff (0x8000) MS[b]
[9] 1 0 0x000b8000 - 0x000bffff (0x8000) MS[b]
[10] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[11] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[12] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b]
[13] 0 0 0x000003c0 - 0x000003df (0x20) IS[b]
[14] 1 0 0x000003b0 - 0x000003bb (0xc) IS[b]
[15] 1 0 0x000003c0 - 0x000003df (0x20) IS[b]
(==) RADEONHD(0): Depth 24, (--) framebuffer bpp 32
(**) RADEONHD(0): Selected ShadowFB.
(II) RADEONHD(0): Unknown card detected: 0x9501:0x1458:0x21A4.
If - and only if - your card does not work or does not work optimally
please contact [email protected] to help rectify this.
Use the subject: 0x9501:0x1458:0x21A4: <name of board>
and *please* describe the problems you are seeing
in your message.
(--) RADEONHD(0): Detected an RV670 on an unidentified card
(II) RADEONHD(0): Mapped IO @ 0xf7000000 to 0x7f39ca36f000 (size 0x00010000)
(II) RADEONHD(0): PCIE Card Detected
(II) RADEONHD(0): Getting BIOS copy from PCI ROM
(II) RADEONHD(0): ATOM BIOS Rom:
SubsystemVendorID: 0x1458 SubsystemID: 0x21a4
IOBaseAddress: 0xa000
Filename: Test.bin
BIOS Bootup Message:
GV-RX387512HP_F10
(II) RADEONHD(0): Default Engine Clock: 825000
(II) RADEONHD(0): Default Memory Clock: 900000
(II) RADEONHD(0): Calling ASIC Init
(II) RADEONHD(0): ASIC_INIT Successful
(II) RADEONHD(0): Analog TV Default Mode: 1
(II) RADEONHD(0): Found default TV Mode NTSC
(II) RADEONHD(0): The detected amount of videoram exceeds the PCI BAR aperture.
(II) RADEONHD(0): Using only 262144kB of the total 524288kB.
(--) RADEONHD(0): VideoRAM: 262144 kByte
(II) RADEONHD(0): Framebuffer space used by Firmware (kb): 16
(II) RADEONHD(0): Start of VRAM area used by Firmware: 0x1fffc000
(II) RADEONHD(0): AtomBIOS requests 16kB of VRAM scratch space
(II) RADEONHD(0): AtomBIOS VRAM scratch base: 0x1fffc000
(WW) RADEONHD(0): rhdAtomAllocateFbScratch: FW FB scratch area 536854528 (size: 16384) extends beyond available framebuffer size 268435456
(II) RADEONHD(0): Cannot get VRAM scratch space. Allocating in main memory instead
(II) RADEONHD(0): Default Engine Clock: 825000
(II) RADEONHD(0): Default Memory Clock: 900000
(II) RADEONHD(0): Maximum Pixel ClockPLL Frequency Output: 1200000
(II) RADEONHD(0): Minimum Pixel ClockPLL Frequency Output: 0
(II) RADEONHD(0): Maximum Pixel ClockPLL Frequency Input: 13500
(II) RADEONHD(0): Minimum Pixel ClockPLL Frequency Input: 1000
(II) RADEONHD(0): Maximum Pixel Clock: 400000
(II) RADEONHD(0): Reference Clock: 27000
(II) RADEONHD(0): Direct rendering not officially supported on R600 and up
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Module "i2c" already built-in
(II) RADEONHD(0): Reference Clock: 27000
(II) RADEONHD(0): GPIO_I2C_Clk_Mask: 0x1f90
(II) RADEONHD(0): GPIO_I2C_Clk_Mask_Shift: 0x0
(II) RADEONHD(0): GPIO_I2C_Data_Mask: 0x1f90
(II) RADEONHD(0): GPIO_I2C_Data_Mask_Shift: 0x8
(II) RADEONHD(0): I2C bus "RHD I2C line 0" initialized.
(II) RADEONHD(0): GPIO_I2C_Clk_Mask: 0x1f94
(II) RADEONHD(0): GPIO_I2C_Clk_Mask_Shift: 0x0
(II) RADEONHD(0): GPIO_I2C_Data_Mask: 0x1f94
(II) RADEONHD(0): GPIO_I2C_Data_Mask_Shift: 0x8
(II) RADEONHD(0): I2C bus "RHD I2C line 1" initialized.
(II) RADEONHD(0): GPIO_I2C_Clk_Mask: 0x1f98
(II) RADEONHD(0): GPIO_I2C_Clk_Mask_Shift: 0x0
(II) RADEONHD(0): GPIO_I2C_Data_Mask: 0x1f98
(II) RADEONHD(0): GPIO_I2C_Data_Mask_Shift: 0x8
(II) RADEONHD(0): I2C bus "RHD I2C line 2" initialized.
(II) RADEONHD(0): GPIO_I2C_Clk_Mask: 0x1f80
(II) RADEONHD(0): GPIO_I2C_Clk_Mask_Shift: 0x0
(II) RADEONHD(0): GPIO_I2C_Data_Mask: 0x1f80
(II) RADEONHD(0): GPIO_I2C_Data_Mask_Shift: 0x8
(II) RADEONHD(0): I2C bus "RHD I2C line 3" initialized.
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) RADEONHD(0): Detected VGA mode.
(II) RADEONHD(0): Minimum Pixel ClockPLL Frequency Output: 0
(II) RADEONHD(0): Maximum Pixel ClockPLL Frequency Output: 1200000
(II) RADEONHD(0): Maximum Pixel Clock: 400000
(II) RADEONHD(0): Reference Clock: 27000
(II) RADEONHD(0): FB: Allocated Cursor Image at offset 0x00000000 (size = 0x00004000)
(II) RADEONHD(0): FB: Allocated Cursor Image at offset 0x00004000 (size = 0x00004000)
(II) RADEONHD(0): Connector[0] {RHD_CONNECTOR_DVI, "DUAL_LINK_DVI_I DFP1 CRT2", RHD_DDC_1, RHD_HPD_0, { RHD_OUTPUT_TMDSA, RHD_OUTPUT_DACB } }
(II) RADEONHD(0): Connector[1] {RHD_CONNECTOR_TV, "7PIN_DIN TV1 CV", RHD_DDC_0, RHD_HPD_NONE, { RHD_OUTPUT_DACB, RHD_OUTPUT_NONE } }
(II) RADEONHD(0): Connector[2] {RHD_CONNECTOR_DVI, "DUAL_LINK_DVI_I CRT1 DFP2", RHD_DDC_0, RHD_HPD_1, { RHD_OUTPUT_LVTMA, RHD_OUTPUT_DACA } }
(--) RADEONHD(0): Attaching Output TMDS A to Connector DVI-I 1
(--) RADEONHD(0): Attaching Output DAC B to Connector DVI-I 1
(--) RADEONHD(0): Attaching Output DAC B to Connector TV 7PIN_DIN
(--) RADEONHD(0): Attaching Output TMDS B to Connector DVI-I 2
(--) RADEONHD(0): Attaching Output DAC A to Connector DVI-I 2
(II) RADEONHD(0): RandR: Adding RRoutput DVI-I_1/digital for Output TMDS A
(II) RADEONHD(0): RandR: Adding RRoutput DVI-I_1/analog for Output DAC B
(II) RADEONHD(0): RandR: Adding RRoutput TV_7PIN_DIN for Output DAC B
(II) RADEONHD(0): RandR: Adding RRoutput DVI-I_2/digital for Output TMDS B
(II) RADEONHD(0): RandR: Adding RRoutput DVI-I_2/analog for Output DAC A
(II) RADEONHD(0): Output DVI-I_1/digital using monitor section Monitor0
(II) RADEONHD(0): Output DVI-I_1/digital has no monitor section
(II) RADEONHD(0): Output DVI-I_1/analog has no monitor section
(II) RADEONHD(0): Output TV_7PIN_DIN has no monitor section
(II) RADEONHD(0): Output DVI-I_2/digital has no monitor section
(II) RADEONHD(0): Output DVI-I_2/analog has no monitor section
(II) RADEONHD(0): TMDS A: Sensed Output: DVI
(II) RADEONHD(0): Setting TMDS A to incoherent
(II) RADEONHD(0): I2C device "RHD I2C line 1:E-EDID segment register" registered at address 0x60.
(II) RADEONHD(0): I2C device "RHD I2C line 1:ddc2" registered at address 0xA0.
(II) RADEONHD(0): EDID data for W2253
(II) RADEONHD(0): Manufacturer: GSM Model: 56dc Serial#: 385315
(II) RADEONHD(0): Year: 2009 Week: 5
(II) RADEONHD(0): EDID Version: 1.3
(II) RADEONHD(0): Digital Display Input
(II) RADEONHD(0): Max Image Size [cm]: horiz.: 49 vert.: 32
(II) RADEONHD(0): Gamma: 2.20
(II) RADEONHD(0): DPMS capabilities: StandBy Suspend Off
(II) RADEONHD(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
(II) RADEONHD(0): First detailed timing is preferred mode
(II) RADEONHD(0): redX: 0.640 redY: 0.330 greenX: 0.300 greenY: 0.600
(II) RADEONHD(0): blueX: 0.150 blueY: 0.060 whiteX: 0.312 whiteY: 0.329
(II) RADEONHD(0): Supported established timings:
(II) RADEONHD(0): 720x400@70Hz
(II) RADEONHD(0): 640x480@60Hz
(II) RADEONHD(0): 640x480@75Hz
(II) RADEONHD(0): 800x600@56Hz
(II) RADEONHD(0): 800x600@60Hz
(II) RADEONHD(0): 800x600@75Hz
(II) RADEONHD(0): 832x624@75Hz
(II) RADEONHD(0): 1024x768@60Hz
(II) RADEONHD(0): 1024x768@75Hz
(II) RADEONHD(0): 1280x1024@75Hz
(II) RADEONHD(0): 1152x870@75Hz
(II) RADEONHD(0): Manufacturer's mask: 0
(II) RADEONHD(0): Supported standard timings:
(II) RADEONHD(0): #0: hsize: 1680 vsize 1050 refresh: 60 vid: 179
(II) RADEONHD(0): #1: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
(II) RADEONHD(0): #2: hsize: 1280 vsize 1024 refresh: 75 vid: 36737
(II) RADEONHD(0): #3: hsize: 1152 vsize 864 refresh: 75 vid: 20337
(II) RADEONHD(0): Supported detailed timing:
(II) RADEONHD(0): clock: 138.5 MHz Image Size: 510 x 290 mm
(II) RADEONHD(0): h_active: 1920 h_sync: 1968 h_sync_end 2000 h_blank_end 2080 h_border: 0
(II) RADEONHD(0): v_active: 1080 v_sync: 1083 v_sync_end 1088 v_blanking: 1111 v_border: 0
(II) RADEONHD(0): Supported detailed timing:
(II) RADEONHD(0): clock: 148.5 MHz Image Size: 510 x 290 mm
(II) RADEONHD(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
(II) RADEONHD(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
(II) RADEONHD(0): Ranges: V min: 56 V max: 75 Hz, H min: 30 H max: 83 kHz, PixClock max 150 MHz
(II) RADEONHD(0): Monitor name: W2253
(II) RADEONHD(0): EDID (in hex):
(II) RADEONHD(0): 00ffffffffffff001e6ddc5623e10500
(II) RADEONHD(0): 0513010380312078eaee91a3544c9926
(II) RADEONHD(0): 0f5054a76b80b3008180818f714f0101
(II) RADEONHD(0): 0101010101011a3680a070381f403020
(II) RADEONHD(0): 3500fe221100001e023a801871382d40
(II) RADEONHD(0): 582c4500fe221100001c000000fd0038
(II) RADEONHD(0): 4b1e530f000a202020202020000000fc
(II) RADEONHD(0): 0057323235330a202020202020200081
(II) RADEONHD(0): EDID vendor "GSM", prod id 22236
(II) RADEONHD(0): Using EDID range info for horizontal sync
(II) RADEONHD(0): Using EDID range info for vertical refresh
(II) RADEONHD(0): Printing DDC gathered Modelines:
(II) RADEONHD(0): Modeline "1920x1080"x0.0 138.50 1920 1968 2000 2080 1080 1083 1088 1111 +hsync +vsync (66.6 kHz)
(II) RADEONHD(0): Modeline "1920x1080"x0.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 -hsync +vsync (67.5 kHz)
(II) RADEONHD(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(II) RADEONHD(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
(II) RADEONHD(0): Modeline "640x480"x0.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
(II) RADEONHD(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) RADEONHD(0): Modeline "720x400"x0.0 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
(II) RADEONHD(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) RADEONHD(0): Modeline "1024x768"x0.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz)
(II) RADEONHD(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) RADEONHD(0): Modeline "832x624"x0.0 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
(II) RADEONHD(0): Modeline "800x600"x0.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
(II) RADEONHD(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
(II) RADEONHD(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
(II) RADEONHD(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) RADEONHD(0): Modeline "1280x1024"x0.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) RADEONHD(0): Modeline "1152x864"x0.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz)
(II) RADEONHD(0): Output DVI-I_1/digital connected
(II) RADEONHD(0): Output DVI-I_1/analog disconnected
(II) RADEONHD(0): Output TV_7PIN_DIN disconnected
(II) RADEONHD(0): Output DVI-I_2/digital disconnected
(II) RADEONHD(0): Output DVI-I_2/analog disconnected
(II) RADEONHD(0): Using exact sizes for initial modes
(II) RADEONHD(0): Output DVI-I_1/digital using initial mode 1920x1080
(II) RADEONHD(0): RandR 1.2 support enabled
(==) RADEONHD(0): RGB weight 888
(==) RADEONHD(0): Default visual is TrueColor
(==) RADEONHD(0): Using gamma correction (1.0, 1.0, 1.0)
(II) RADEONHD(0): Using 1920x1920 Framebuffer with 1920 pitch
(II) RADEONHD(0): FB: Allocated ScanoutBuffer at offset 0x00008000 (size = 0x00E10000)
(**) RADEONHD(0): Display dimensions: (490, 320) mm
(**) RADEONHD(0): DPI set to (99, 152)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.6.3.901, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(II) Loading sub module "shadow"
(II) LoadModule: "shadow"
(II) Loading /usr/lib/xorg/modules//libshadow.so
(II) Module shadow: vendor="X.Org Foundation"
compiled for 1.6.3.901, module version = 1.1.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) RADEONHD(0): Using ShadowFB
(==) RADEONHD(1): Depth 24, (--) framebuffer bpp 32
(**) RADEONHD(1): Selected ShadowFB.
(II) RADEONHD(1): Unknown card detected: 0x9501:0x1458:0x21A4.
If - and only if - your card does not work or does not work optimally
please contact [email protected] to help rectify this.
Use the subject: 0x9501:0x1458:0x21A4: <name of board>
and *please* describe the problems you are seeing
in your message.
(--) RADEONHD(1): Detected an RV670 on an unidentified card
(II) RADEONHD(1): Mapped IO @ 0xf5000000 to 0x7f39ca36f000 (size 0x00010000)
(II) RADEONHD(1): PCIE Card Detected
(II) RADEONHD(1): Getting BIOS copy from PCI ROM
(II) RADEONHD(1): ATOM BIOS Rom:
SubsystemVendorID: 0x1458 SubsystemID: 0x21a4
IOBaseAddress: 0x0000
Filename: Test.bin
BIOS Bootup Message:
GV-RX387512HP_F10
(II) RADEONHD(1): Default Engine Clock: 825000
(II) RADEONHD(1): Default Memory Clock: 900000
(II) RADEONHD(1): Calling ASIC Init
(II) RADEONHD(1): ASIC_INIT Successful
(II) RADEONHD(1): Analog TV Default Mode: 27049664
(II) RADEONHD(1): The detected amount of videoram exceeds the PCI BAR aperture.
(II) RADEONHD(1): Using only 262144kB of the total 524288kB.
(--) RADEONHD(1): VideoRAM: 262144 kByte
(II) RADEONHD(1): Framebuffer space used by Firmware (kb): 0
(WW) RADEONHD(1): rhdAtomGetFbBaseAndSize: AtomBIOS specified VRAM scratch space size invalid
(II) RADEONHD(1): default to: 20480
(II) RADEONHD(1): Cannot get VRAM scratch space. Allocating in main memory instead
(II) RADEONHD(1): Default Engine Clock: 825000
(II) RADEONHD(1): Default Memory Clock: 900000
(II) RADEONHD(1): Maximum Pixel ClockPLL Frequency Output: 1200000
(II) RADEONHD(1): Minimum Pixel ClockPLL Frequency Output: 0
(II) RADEONHD(1): Maximum Pixel ClockPLL Frequency Input: 13500
(II) RADEONHD(1): Minimum Pixel ClockPLL Frequency Input: 1000
(II) RADEONHD(1): Maximum Pixel Clock: 400000
(II) RADEONHD(1): Reference Clock: 27000
(II) RADEONHD(1): Direct rendering not officially supported on R600 and up
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Module "i2c" already built-in
(II) RADEONHD(1): Reference Clock: 27000
(II) RADEONHD(1): GPIO_I2C_Clk_Mask: 0x1f90
(II) RADEONHD(1): GPIO_I2C_Clk_Mask_Shift: 0x0
(II) RADEONHD(1): GPIO_I2C_Data_Mask: 0x1f90
(II) RADEONHD(1): GPIO_I2C_Data_Mask_Shift: 0x8
(II) RADEONHD(1): I2C bus "RHD I2C line 0" initialized.
(II) RADEONHD(1): GPIO_I2C_Clk_Mask: 0x1f94
(II) RADEONHD(1): GPIO_I2C_Clk_Mask_Shift: 0x0
(II) RADEONHD(1): GPIO_I2C_Data_Mask: 0x1f94
(II) RADEONHD(1): GPIO_I2C_Data_Mask_Shift: 0x8
(II) RADEONHD(1): I2C bus "RHD I2C line 1" initialized.
(II) RADEONHD(1): GPIO_I2C_Clk_Mask: 0x1f98
(II) RADEONHD(1): GPIO_I2C_Clk_Mask_Shift: 0x0
(II) RADEONHD(1): GPIO_I2C_Data_Mask: 0x1f98
(II) RADEONHD(1): GPIO_I2C_Data_Mask_Shift: 0x8
(II) RADEONHD(1): I2C bus "RHD I2C line 2" initialized.
(II) RADEONHD(1): GPIO_I2C_Clk_Mask: 0x1f80
(II) RADEONHD(1): GPIO_I2C_Clk_Mask_Shift: 0x0
(II) RADEONHD(1): GPIO_I2C_Data_Mask: 0x1f80
(II) RADEONHD(1): GPIO_I2C_Data_Mask_Shift: 0x8
(II) RADEONHD(1): I2C bus "RHD I2C line 3" initialized.
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) RADEONHD(1): Detected VGA mode.
(II) RADEONHD(1): Minimum Pixel ClockPLL Frequency Output: 0
(II) RADEONHD(1): Maximum Pixel ClockPLL Frequency Output: 1200000
(II) RADEONHD(1): Maximum Pixel Clock: 400000
(II) RADEONHD(1): Reference Clock: 27000
(II) RADEONHD(1): FB: Allocated Cursor Image at offset 0x00000000 (size = 0x00004000)
(II) RADEONHD(1): FB: Allocated Cursor Image at offset 0x00004000 (size = 0x00004000)
(II) RADEONHD(1): Connector[0] {RHD_CONNECTOR_DVI, "DUAL_LINK_DVI_I DFP1 CRT2", RHD_DDC_1, RHD_HPD_0, { RHD_OUTPUT_TMDSA, RHD_OUTPUT_DACB } }
(II) RADEONHD(1): Connector[1] {RHD_CONNECTOR_TV, "7PIN_DIN TV1 CV", RHD_DDC_0, RHD_HPD_NONE, { RHD_OUTPUT_DACB, RHD_OUTPUT_NONE } }
(II) RADEONHD(1): Connector[2] {RHD_CONNECTOR_DVI, "DUAL_LINK_DVI_I CRT1 DFP2", RHD_DDC_0, RHD_HPD_1, { RHD_OUTPUT_LVTMA, RHD_OUTPUT_DACA } }
(--) RADEONHD(1): Attaching Output TMDS A to Connector DVI-I 1
(--) RADEONHD(1): Attaching Output DAC B to Connector DVI-I 1
(--) RADEONHD(1): Attaching Output DAC B to Connector TV 7PIN_DIN
(--) RADEONHD(1): Attaching Output TMDS B to Connector DVI-I 2
(--) RADEONHD(1): Attaching Output DAC A to Connector DVI-I 2
(II) RADEONHD(1): RandR: Adding RRoutput DVI-I_1/digital for Output TMDS A
(II) RADEONHD(1): RandR: Adding RRoutput DVI-I_1/analog for Output DAC B
(II) RADEONHD(1): RandR: Adding RRoutput TV_7PIN_DIN for Output DAC B
(II) RADEONHD(1): RandR: Adding RRoutput DVI-I_2/digital for Output TMDS B
(II) RADEONHD(1): RandR: Adding RRoutput DVI-I_2/analog for Output DAC A
(II) RADEONHD(1): Output DVI-I_1/digital using monitor section Monitor1
(II) RADEONHD(1): Output DVI-I_1/digital has no monitor section
(II) RADEONHD(1): Output DVI-I_1/analog has no monitor section
(II) RADEONHD(1): Output TV_7PIN_DIN has no monitor section
(II) RADEONHD(1): Output DVI-I_2/digital has no monitor section
(II) RADEONHD(1): Output DVI-I_2/analog has no monitor section
(II) RADEONHD(1): Output DVI-I_1/digital disconnected
(II) RADEONHD(1): Output DVI-I_1/analog disconnected
(II) RADEONHD(1): Output TV_7PIN_DIN disconnected
(II) RADEONHD(1): Output DVI-I_2/digital disconnected
(II) RADEONHD(1): Output DVI-I_2/analog disconnected
(WW) RADEONHD(1): No outputs definitely connected, trying again...
(II) RADEONHD(1): Output DVI-I_1/digital disconnected
(II) RADEONHD(1): Output DVI-I_1/analog disconnected
(II) RADEONHD(1): Output TV_7PIN_DIN disconnected
(II) RADEONHD(1): Output DVI-I_2/digital disconnected
(II) RADEONHD(1): Output DVI-I_2/analog disconnected
(WW) RADEONHD(1): Unable to find initial modes
(EE) RADEONHD(1): RandR: No valid modes. Disabling RandR support.
(EE) RADEONHD(1): Failed to detect a connected monitor
(II) RADEONHD(1): Destroying TMDS A
(II) RADEONHD(1): Destroying DAC B
(II) RADEONHD(1): Destroying TMDS B
(II) RADEONHD(1): Destroying DAC A
(II) RADEONHD(1): I2C bus "RHD I2C line 0" removed.
(II) RADEONHD(1): I2C bus "RHD I2C line 1" removed.
(II) RADEONHD(1): I2C bus "RHD I2C line 2" removed.
(II) RADEONHD(1): I2C bus "RHD I2C line 3" removed.
(II) UnloadModule: "radeonhd"
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b]
[5] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b]
[6] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b]
[7] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[8] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[9] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b]
[10] 0 0 0x000003c0 - 0x000003df (0x20) IS[b]
(II) RADEONHD(0): Mapped IO @ 0xf7000000 to 0x7f39ca36f000 (size 0x00010000)
(II) RADEONHD(0): Mapped FB @ 0xd0000000 to 0x7f39b66f6000 (size 0x10000000)
(WW) RADEONHD(0): RHDCSInit: No CS for R600 and up yet.
(==) RADEONHD(0): Backing store disabled
(==) RADEONHD(0): Silken mouse enabled
(II) RADEONHD(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(II) RADEONHD(0): On Crtc 0 Setting 59.9 Hz Mode: Modeline "1920x1080" 138.50 1920 1968 2000 2080 1080 1083 1088 1111 +hsync +vsync
None
(II) RADEONHD(0): RHDAudioSetClock: using TMDS A as clock source with 138500 khz
(II) RADEONHD(0): Using ACR timing N=4096 CTS=138500 for frequency 32000
(II) RADEONHD(0): Using ACR timing N=6272 CTS=153888 for frequency 44100
(II) RADEONHD(0): Using ACR timing N=6144 CTS=138500 for frequency 48000
(II) RADEONHD(0): RHDAudioSetSupported: config 0x60040 codec 0x1
(II) RADEONHD(0): DPMS enabled
(--) RandR disabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) AIGLX: Screen 0 is not DRI2 capable
(II) AIGLX: Screen 0 is not DRI capable
(II) AIGLX: Loaded and initialized /usr/lib/xorg/modules/dri/swrast_dri.so
(II) GLX: Initialized DRISWRAST GL provider for screen 0
(II) RADEONHD(0): Setting screen physical size to 510 x 290
(II) config/hal: Adding input device Macintosh mouse button emulation
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input//evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
compiled for 1.6.3, module version = 2.2.5
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 4.0
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
(**) Macintosh mouse button emulation: (accel) filter chain progression: 2.00
(**) Macintosh mouse button emulation: (accel) filter stage 0: 20.00 ms
(**) Macintosh mouse button emulation: (accel) set acceleration profile 0
(II) Macintosh mouse button emulation: initialized for relative axes.
(II) config/hal: Adding input device ImPS/2 Logitech Wheel Mouse
(**) ImPS/2 Logitech Wheel Mouse: always reports core events
(**) ImPS/2 Logitech Wheel Mouse: Device: "/dev/input/event5"
(II) ImPS/2 Logitech Wheel Mouse: Found 3 mouse buttons
(II) ImPS/2 Logitech Wheel Mouse: Found x and y relative axes
(II) ImPS/2 Logitech Wheel Mouse: Found scroll wheel(s)
(II) ImPS/2 Logitech Wheel Mouse: Configuring as mouse
(**) ImPS/2 Logitech Wheel Mouse: YAxisMapping: buttons 4 and 5
(**) ImPS/2 Logitech Wheel Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "ImPS/2 Logitech Wheel Mouse" (type: MOUSE)
(**) ImPS/2 Logitech Wheel Mouse: (accel) keeping acceleration scheme 1
(**) ImPS/2 Logitech Wheel Mouse: (accel) filter chain progression: 2.00
(**) ImPS/2 Logitech Wheel Mouse: (accel) filter stage 0: 20.00 ms
(**) ImPS/2 Logitech Wheel Mouse: (accel) set acceleration profile 0
(II) ImPS/2 Logitech Wheel Mouse: initialized for relative axes.
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event1"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event4"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event3"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) RADEONHD(0): RHDHdmiUpdateAudioSettings: stoped with 1 channels, 48000 Hz sampling rate, 8 bits per sample,
(II) RADEONHD(0): RHDHdmiUpdateAudioSettings: 0x00 IEC60958 status bits and 0x00 category code
(II) RADEONHD(0): RHDHdmiUpdateAudioSettings: stoped with 1 channels, 48000 Hz sampling rate, 8 bits per sample,
(II) RADEONHD(0): RHDHdmiUpdateAudioSettings: 0x00 IEC60958 status bits and 0x00 category code
(II) Macintosh mouse button emulation: Close
(II) UnloadModule: "evdev"
(II) ImPS/2 Logitech Wheel Mouse: Close
(II) UnloadModule: "evdev"
(II) AT Translated Set 2 keyboard: Close
(II) UnloadModule: "evdev"
(II) Power Button: Close
(II) UnloadModule: "evdev"
(II) Power Button: Close
(II) UnloadModule: "evdev"
Last edited by warnab (2009-10-21 18:53:12)

i'm getting then such log
This is a pre-release version of the X server from The X.Org Foundation.
It is not supported in any way.
Bugs may be filed in the bugzilla at http://bugs.freedesktop.org/.
Select the "xorg" product for bugs you find in this release.
Before reporting bugs in pre-release versions please check the
latest version in the X.Org Foundation git repository.
See http://wiki.x.org/wiki/GitPage for git access instructions.
X.Org X Server 1.6.3.901 (1.6.4 RC 1)
Release Date: 2009-8-25
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.30-ARCH x86_64
Current Operating System: Linux kasia 2.6.31-ARCH #1 SMP PREEMPT Tue Oct 13 11:33:39 CEST 2009 x86_64
Build Date: 04 September 2009 05:45:43PM
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Wed Oct 21 22:35:22 2009
(II) Loader magic: 0x1d40
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 5.0
X.Org XInput driver : 4.0
X.Org Server Extension : 2.0
(II) Loader running on linux
(--) using VT number 7
(!!) More than one possible primary device found
(--) PCI: (0:1:0:0) 1002:9501:1458:21a4 ATI Technologies Inc Radeon HD 3870 rev 0, Mem @ 0xd0000000/268435456, 0xf7000000/65536, I/O @ 0x0000a000/256, BIOS @ 0x????????/131072
(--) PCI: (0:2:0:0) 1002:9501:1458:21a4 ATI Technologies Inc Radeon HD 3870 rev 0, Mem @ 0xe0000000/268435456, 0xf5000000/65536, I/O @ 0x0000b000/256, BIOS @ 0x????????/131072
Primary device is not PCI
(==) Using default built-in configuration (21 lines)
(==) --- Start of built-in configuration ---
Section "Device"
Identifier "Builtin Default vesa Device 0"
Driver "vesa"
EndSection
Section "Screen"
Identifier "Builtin Default vesa Screen 0"
Device "Builtin Default vesa Device 0"
EndSection
Section "Device"
Identifier "Builtin Default fbdev Device 0"
Driver "fbdev"
EndSection
Section "Screen"
Identifier "Builtin Default fbdev Screen 0"
Device "Builtin Default fbdev Device 0"
EndSection
Section "ServerLayout"
Identifier "Builtin Default Layout"
Screen "Builtin Default vesa Screen 0"
Screen "Builtin Default fbdev Screen 0"
EndSection
(==) --- End of built-in configuration ---
(==) ServerLayout "Builtin Default Layout"
(**) |-->Screen "Builtin Default vesa Screen 0" (0)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default vesa Device 0"
(==) No monitor specified for screen "Builtin Default vesa Screen 0".
Using a default monitor configuration.
(**) |-->Screen "Builtin Default fbdev Screen 0" (1)
(**) | |-->Monitor "<default monitor>"
(**) | |-->Device "Builtin Default fbdev Device 0"
(==) No monitor specified for screen "Builtin Default fbdev Screen 0".
Using a default monitor configuration.
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/TTF" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/Type1" does not exist.
Entry deleted from font path.
(==) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
built-ins
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on HAL to provide the list of input devices.
If no devices become available, reconfigure HAL or disable AllowEmptyInput.
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) System resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.6.3.901, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.6.3.901, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.6.3.901, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.6.3.901, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.6.3.901, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions//libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.6.3.901, module version = 1.1.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "vesa"
(WW) Warning, couldn't open module vesa
(II) UnloadModule: "vesa"
(EE) Failed to load module "vesa" (module does not exist, 0)
(II) LoadModule: "fbdev"
(WW) Warning, couldn't open module fbdev
(II) UnloadModule: "fbdev"
(EE) Failed to load module "fbdev" (module does not exist, 0)
(EE) No drivers available.
Fatal server error:
no screens found
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
Please also check the log file at "/var/log/Xorg.0.log" for additional information.

Any problems with the recalled hard disk drives, any problems with the recalled hard disk drives

Has anyone had their defective hard drive replaced?
any problems with the Apple service or restarting the machine with a new hard drive?

See this FAQ: http://www.thexlab.com/faqs/freeingspace.html

New hard drive and problems with sync

My problem is that I have installed a new hard drive (Win 7) which I installed itunes on and I cannot sync my ipod. I still have my old hard drive (windows XP) with the original itunes on it and I have tried to back it up but it still wont do it.
I can boot to XP and perform a back up but re-booting to Win7 and trying to restore it dosent work and I still get the syncing issue. I find the suggestion to erase my ipod and reinstall my music, a ridiculous solution and I'm guessing there is an "easy button" somewhere?
help!

I probably should have mentioned this twist. My music is on a seperate drive. So what I have is Win7 on SSD1, WinXP on 2nd drive and media on a 3rd drive.
I backed up my media on both OS's and they seem to conflict with or do not recognize each other. Installing all my music on my SSD along with my Win7 is not an option (too small).
thanks

OS update problem with BB Torch 9810

Hi there
I've got a problem with my BB device. It is Torch 9810 and recently a software patch has been applied ( version 7.0.0 bundle 1465 to bundle 2406 ). After the upgrade though BB device doesn't work properly, its screen freezes, some applications ( GPS in particular ) does not work, virtual keyboard sensitivity is poor etc. Hence I need to roll back to the previous version of software however rollback option on device is disabled. I can't roll back to the previous version using desktop software either.
Please advice how to resolve the issue or provide me with a link where I can find previous OS version i.e. 7.0.0 bundle 1465.
Regards,
Krum Garkov

Hi kgarkov and welcome to the BlackBerry Support Community Forums!
Plug your BlackBerry® smartphone into your PC and go to www.blackberry.com/update. When prompted to do the update, click on View Other Versions to choose an older version of software to install.
Thanks
-CptS
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

Since LION update problem with iphone syncronisation

Since the LION update on our macbook we have problems with the iphone syncronisation, reset the iphone has not solve the problem - what ist the mistake?

What worked for me was not on the Apple troubleshooting list. I tried the whole list.
First, I reset the phone. (Reset the iPhone by holding the sleep/wake button at the top right of the device and the home button at the bottom center of the face at the same time. Hold them both until you see the screen go black and the white Apple logo appear. When this happens, you can let go - the iPhone is rebooting.)
Second, I restored the phone.
I could not restore the phone until I reset it.
Good luck.

2.3 Update: Problem with AppleTV learning third-party remote

Hello,
I'm trying to set up my third party remote (DirecTV HR21) after updating to 2.3. It all starts well; I go to Settings -> General -> Remotes -> Learn Remote, but I am having an issue when I am making my Apple TV learn the second key (down arrow); I get the error message "apple tv has already learned this button". It's as if the Apple TV thinks the 'up arrow' and the 'down arrow' on my remote are the same key. I tried several times, to no avail.
Anyone else having this issue?

I'm experiencing the same problem with the current DirecTV remote not being able to learn more than the first button prompted to enter (arrow-down). The error message "appletv has already learned this button" appears when attempting to enter the second button prompted (arrow-up). Furthermore, I have attempted configuration on two separate DirecTV HR21 remotes in both AV1 and AV2 modes.
Come on Apple -- don't tease us! Testing wasn't done to make sure AppleTV can learn to respond to a current DirecTV remote? Yikes. I wonder what 3rd-party remotes were tested and confirmed to work.

Driver update problems with GTX 760

Similar Messages

Maybe you are looking for