Drivers Failing to Install

I own an HP G62 Notebook PC, and my warrenty expires in 4 days. Iv'e had this problem for awhile but it hasn't affected me too much. The problem is that my USB controllers can't install properly. When I plug in a flash driver it will show that it is installing the device, but then will say failed to install. It will reconise the flash driver as a "Flash Disk". When my computer starts up it will try to install my Universial Serial Bus Controllers but all of them fail to install.
I have attempted to install the drivers manually off the website but it will say " An error occured while trying to install", it will say the same when i attempt to update the devices from the Device Manager. The thing is I use a pen tablet (mostly as a mouse) for my computer. When I plug it in it will say failed to install but the tablet will work fine. Other than that other devices like flash drives and printers fail to install. And the drivers encounter errors every time I try to install.
So my question. Do you think this is a problem with my motherboard? Because if it is I would have to make sure to get it replaced before my warrenty runs out on the 23rd. Or is there a way to fix this? In the Device Manager there is no yellow triangle that pops up next to the USB controllers. There is only one next to the Microsoft Virual WiFi Miniport Adapter_01, which I don't think is in the way of the problem.

New Information:
A Flash Drive that I use to use on my laptop works fine. But any other flash drives such as ones from other people and ones not used before will not install.

Similar Messages

HP Printer and Fax Drivers fails to install, 10.3.9

I am using an iMAC G5 running 10.3.9. Purchased an HP Officejet J6480 all-in-one printer. HP Printer installer fails midway thru install when it reaches the install for the fax drivers. I have downloaded both updates of the driver (9.7 and 9.7.1) from HP and and separately attempted to install each. In both cases, the install failed again at the fax driver install.
I have gone stepwise with HP phone support for both install and uninstall for each HP installer(9.7.1) and the install failed at the same point. HP's assessment is that their product say's it is 10.3 compatible and since it fails only after reaching the the fax driver install, it must be an Apple problem.
Note: I installed the printer on my work-issued Windows XP laptop and it works fine including faxing.
If anyone can provide guidance, it would be appreciated. Thanks in advance.

Hang on, the 10.3.9 Mac only had 256MB RAM ? Could be part of the cause. I remember reading the minimum requirements, and I do remember it was more than 256MB RAM, maybe 384MB.
I downloaded the 9.7.1 update, it's nearly 200MB. OUCH! Didn't try to install it on my 10.3.9 G4, but did check if it would allow a partial install with a little bit of trickery. It didn't want to play.
Try again with the 2GB installed, if it's still playing up I'll try installing it here. At least then we'll know.
I've loved HP too, had HP and Epson before moving to Canon. The HP was great, but the new kit I looked at (might have been a 6300 Series model got truly awful customer ratings on Amazon and HP sites, especially from Mac users on all versions of OSX.
I'm hopeful the extra RAM will make all the difference.

HP 8620 drivers fail to install on SBS 2011

We have repeatedly tried to install the HP OfficeJet Pro 8620 printer on our server to share out to the network machines and the installation ALWAYS fails about 50% in. "Unsuccessful Network Installation" is the dialog we get.
The HP tools to diagnose the installtion probelm does not work on SBS 2011 (Server 2008 R2 x64). Is there a way to install this printer?
Even when we downloaded just the drivers and installed the printer it does not print to the printner. We can install the software on individual machines but there are many of them and we'd rather control this from the server side.
There is no firewall running on this server.

I ran Windows Fixit and after that the patch installed without a problem (see my previous reply).
The Windows Fixit tool did show that it fixed some problems and the update did install after that.
I believe that it is too late for me to run checksur and get anything meaningfull since it appears the problems have been fixed and the update is now installed.
In hindsight I wish that I had not run the Windows Fixit and instead took your advice and maybe I would have been able to determine what the problem was.
Just as a side note, I did manually download the patch and tried to install it prior to the Windows Fixit and it still did not install.

G780 Wireless Drivers - Failed to install

I recently purchased a Lenovo G780 from newegg on some end of year sales, the computer came with (almost) exactly what I was looking for and within a price range I was comfortable in investing. I am very happy with the performance of the PC, but ultimately decided to swap windows 8 out for windows 7 home premuim.
That said I have done a clean installation of Win7, downloaded all the drivers from the support section of the website. Everything was working and going great until I got to this driver Intel WiMax Driver. The card is identified in the device manager as "Network Controller" but has no driver, nor can windows find another to install. I spent a few hours searching here and on google, unable to find similar problems regarding the wifi.
When the file for the download is opened, it gives a message saying "Unable to find specified path" or something along the lines and closes through a series of message boxes. My question is there perhaps an older version of the driver that can be downloaded from lenovo? Or is there something I have overlooked? I would very much like to get the Wifi working, as it is the last hurdle to getting everything set up.
Thank you for your time!
-Josh
Solved!
Go to Solution.

hi Joshly,
Upon closely checking the spare parts on the Lenovo G780, it looks like it has a Broadcom BCM4313 802.11b/g/n Wireless Network Adapter. To verify if this is really the WLAN card on your PC, use AIDA64 Extreme Edition to determine the model type. Click on the spoiler for details.
Spoiler (Highlight to read)
If this is your wireless adapter, install the Windows 7 (32bit & 64bit) drivers below:
WiFi Link Driver (Intel, CyberTan, Liteon)
v15.0.0.75/5.100.82.112/9.2.0.462/5.100.82.112
0wwl07ww.exe
179MB
Edit: Added a direct link for the Windows 7 drivers
Let me know if you get any errors
Cheers
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Pci can drivers fail to install for ni-can 2.3.3

after upgrading to labview 8.2, i realized that i needed to upgrade my
version of ni-can in order to access my pci can interface. the
pci can card had been working fine with labview 8.0 and ni can 2.3.2 up
to this point. i left the card in the machine, downloaded ni can
2.3.3, and ran the installer. however, when i rebooted and the
"found new hardware" wizard launched, it was unable to locate the
driver files. after selecting to let the system locate driver
files automatically, i recieved the error message:
there was a problem installing this hardware
an error occurred during the installation of the device
the system cannot find the file specified
i then attempted uninstalling ni can, removing the card, reinstalling
the software, and THEN reinstalling the card; however this produced the
same results. any ideas on what i need to do to get drivers
installed that will work with labview 8.2?
thanks.
Ben.

Hi
First of all you need to act with administrator rights.
It seems something went wrong during driver upgrade. Right now the situation is that you have the 2.3.2 driver installed and the device is in the computer too?
If not uninstall 2.3.3 and reinstall 2.3.2 and the CAN device and reboot.
Now remove the CAN device first and after booting again uninstall the driver and delete the NI CAN folder if still available.This will hopefully remove all hardware related information from the registry.
Then boot again and install the 2.3.3 driver, then boot again and install the device.
Hope that helps.
DirkW

I have a copy of Windows 7, and I am trying to bring up Boot Camp on my MacBook with Snow Leopard. But my Snow Leopard install disk is too old for Windows 7, so attempted Boot Camp install of drivers fails.

I have a copy of Windows 7, and I am trying to bring up Boot Camp on my MacBook with Snow Leopard. But my Snow Leopard install disk is too old for Windows 7, so attempted Boot Camp install of drivers fails.
I have hand-installed the NVidia graphics driver, and I have keyboard, minimal trackpad, and hardwire to internet all working. So the WIndows machine is usable. But I am hurting for wi-fi, better trackpad, and whatever else is delivered by Boot Camp. I can't use any of the Boot Camp upgrades because I do not have XP or Vista.

While we all have MacBooks in this forum not all of us use Boot Camp. There's a Boot Camp Support Community where everybody uses Boot Camp. You should also post this question there.
https://discussions.apple.com/community/windows_software/boot_camp

Vista 32 - ipod not recognized, failed to install drivers, disconnecting

Hi to all,
I have experienced a problem with my brand new Ipod classic 80GB and was flustrated by it. It took me some time ro research internet to find a fix for this problem and i would like to share it with you to have it at one place. If such article exists here i appologize, i did not find it myself.
_The problem:_
Ipod in Windows Vista 32 *cannot find/install drivers*. Ipod shows up for couple of seconds and then *automaticaly disconnects*.
Solution:
i have found solution that worked form me at this site
[http://teknobabble.wordpress.com/2007/08/18/vista-driver-problems-installing-a- usb-media-reader-a-solution>
Thanks to the autor of this article and i hape this helps some of you having the same problem as i had

Can you be specific as to what drivers are not installing? An issue that can be had when doing PNPEnum is that child devices of something that does not have a driver installed are not visible to the PNPEnum. A way to get around that is you can force the
injection of drivers that are not getting installed. Something like you can add a second Inject Driver step but, have it be a selection profile of drivers that always get missed because they are children.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

Failed to install drivers in Windows Vista using MDT 2012 update 1

I am trying to deploy physical machine with Windows vista along with drivers. After completion of deployment i see deployment is successful with no error and warnings, but it still do not install driver in the machine. To test weather i have selected correct
driver i checked manual installation of drivers and this install the driver in the machine. But the drivers are not installing when i am tried to install driver using MDT. In windows 7 and Windows XP drivers are installed correctly but not in Windows Vista.
I have shared my log files in one drive. Please look this and tell what mistake i am doing.
https://onedrive.live.com/?cid=BD291DD4A63B1353&id=BD291DD4A63B1353!107
https://onedrive.live.com/?cid=BD291DD4A63B1353&id=BD291DD4A63B1353!109
https://onedrive.live.com/?cid=BD291DD4A63B1353&id=BD291DD4A63B1353!108
https://onedrive.live.com/?cid=BD291DD4A63B1353&id=BD291DD4A63B1353!110
https://onedrive.live.com/?cid=BD291DD4A63B1353&id=BD291DD4A63B1353!112
https://onedrive.live.com/?cid=BD291DD4A63B1353&id=BD291DD4A63B1353!111
https://onedrive.live.com/?cid=BD291DD4A63B1353&id=BD291DD4A63B1353!114
https://onedrive.live.com/?cid=BD291DD4A63B1353&id=BD291DD4A63B1353!113

Can you be specific as to what drivers are not installing? An issue that can be had when doing PNPEnum is that child devices of something that does not have a driver installed are not visible to the PNPEnum. A way to get around that is you can force the
injection of drivers that are not getting installed. Something like you can add a second Inject Driver step but, have it be a selection profile of drivers that always get missed because they are children.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

HP C1680 fails to install Software

Can you please help
I have just reinstalled my operating system Windows 7 6- bit OS and needed to reinstall my printer HP Photosmart C6180 All in One. When I first got my new PC( Dell XPS 501L windows 7 Intel core i5. 243M 2.40GHz) I originally install the whole package with no issues.
after the reinstall of the OS, this is issue I was I getting when I tried to reinstalled the HP application (AIO_CDA_FSW_Full_Win_WW_130_140.exe )
Error message:-
C:\Users\andylouey\AppData\Local\Temp\7zS4864\setup\HPzPNP.ice.
I have done the following:
Tried to install from an old download of the software. Result Failed to install message as above.
Tried the original install CD and also tried to use them in various compatibility modes. Result Failed.
Downloaded the critical updates from HP solved the above error message result the above error message was solved.
Downloaded the latest install software program for my HP printer from the HP website tried again to install failed
Ran the HP Scan doctor reported that the printer drivers are all working asked it to run the scan program it reported that it need the full install of the C1680 software to run this
I got the download again ran it. It extracts the file then just disappears and looking at the task manager there is not install running. So again failed
For the second time I downloaded the HP installer network printer wizard but this failed and just keeps going round in circles> It finishes the download gets to the extracting point and then goes back to the identify printer( which is listed) then goes back once again and downloads the install software.
Other steps I have taken. I used the old installation disk to do a complete uninstall of all the drivers and software using Utilities> CCC> Uninstall_ L2.bat . This wored and uninstalled the printer and drivers and I think any remaining software. I also deleted all the %TEMP% files that my Laptop would allow.
Then once again I I used the install wizard first without the USB cable disconnected then the wizard asked me to plug it in. I plugged it in and HP Wizard found the printer and downloaded the appropriate software completed the download and extracted it and then NOTHING.
I have also downloaded the critical update:-
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-126392-2&cc=uk&dlc=en&lc=en...
Can you suggest a solution help. In my view I need to start from scratch and remove all traces of any HP software and drivers and start over. My only issue with this I have done this and still have the same issues. If I go to Microsoft uninstall utility there isn’t anything to uninstall.
Thanks in advance for your reply.
PS. HP wizard has finished downloading for the fourth time and looping to discovering the device again :-( HELP!!!!!!!!
Thanks in adbance for your replies Andy

Hi
Thank you for your reply and your advice and help
If you look at my help request aboveI have described that I have done your suggetion and yet there are still traces of HP on my hard drive and I am still haveing the same issues.
Below are the steps you have referred to which I covered in my original request :-
Other steps I have taken. I used the old installation disk to do a complete uninstall of all the drivers using CCC> Utilities and Uninstall_L3 . I also deleted all the %TEMP% files (7z) that my Laptop would allow.
Then once again I I used the install wizard first wit the USB cable disconnected then the wizard asked me to plug it in. I plugged it in and HP Wizard found the printer and downloaded the appropriate software completed the download and extracted it and then NOTHING. Except the drivers were installed and the printer was shown in the devices and printers.
I have also downloaded the critical update:-
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-126392-2&cc=uk&dlc=en&lc=en...
Can you suggest a solution help. In my view I need to start from scratch and remove all traces of any HP software and drivers and start over. My only issue with this I have done this and still have the same issues. If I go to Microsoft uninstall utility there isn’t anything to uninstall.
I can print to the printer both wirelessly and via the USB port. But the Solution center will not install just keeps looping. ie idenifies the printer downloads the latest sofware and extracts it then just dissapears of the screen. Nothing comes up and there are no HP programs running in the applications task manager and no processes either.
Thank you in advance for your reply. Regards Andy

WLAN driver fails to install on G580 Windows 7 x64 with error "BCM4313: Can not find setup file"

Summary:
I have installed Windows 7 Ultimate x64 on my G580. Everything is working fine except the WLAN driver fails to install with the error "BCM4313: Can not find setup file".
Details:
I bought lenovo G580 with Windows 8. Since my parents are not comfortable with the learning curve of Win 8, I successfully downgraded to Windows 7 Ultimate x64. Everything is working fine but my WLAN card is not recognized because of lack of driver.
The lenovo parts look-up page says I have broadcom WLAN card - CBT BCM4313 MOW HMC WLAN
I looked at lenovo driver downloads site and tried following driver files for Windows 7 and both of them failed to install with the following error. I tried installing other WLAN drivers also but they won't even install as required hardward is not there.
Error - "BCM4313: Can not find setup file"
Drivers Tried:
- http://support.lenovo.com/en_US/downloads/detail.page?DocID=DS028105
- http://support.lenovo.com/en_US/downloads/detail.page?DocID=DS028208
Any help about how to get past this error will be appreciated. The previous Widnows verison (Windows 8) is still on my hard-drive as windows.old folder. Let me know if I can copy a specific file from there.
Thank you.
BJS
Solved!
Go to Solution.

Download this driver bcm4313
Start setup and extract the files.After that go to star menu/control panel/system/device manager.There you probably find out that network adapter driver is missing.Choose it and click with right mb for drop menu to show up.Select properties then Driver/Update Drivers...Select to load driver from computer hard drive and choose the path where extract files is.Default path is main partion C: and search for directory named Driver.
And yes...you get "Can not find setup file" error but dont worry.Files needed to instal driver are extract fine.

Boot Camp 3.3 fail to install on my iMac

Hi,
My iMac is running with Windows 7 Pro x64 wit Boot Camp 3.2. When I try to install Boot Camp 3.3 with Apple Software Update it ask me to reboot and I still have Boot Camp 3.2 running on my machine.
If I download Boot Camp 3.3 and execute it manually, it give me an error message : Fail to install Boot Camp Services (or something like that, as it is in french)
I used to have issue to install Boot Camp 3.1 and 3.2 where the only option to setup it that I find in this forum was to extract the setup files and run manually the BootCampUpdate64 file. Unfortunatly I cannot do that anymore with 3.3 as it is in a package that I cant extract.
Any idea on how I can fix that ?
Thanks.

Have you found a solution yet? I'm still searching for one. No additional drivers and no VNC installed. Thought it might Splashtop Streamer, but it doesn't install an additional driver like LogMeIn does. Also tried removing Sata and USB PCIe cards. Still no luck. In a last ditch effort I tried to uninstall Boot Camp Services completely which also failed.

USB Console (Serial) Driver fails to install on Windows 8.1 x64

The USB console cable driver v3.1 will not install on Windows 8.1 x64. Had a similar problem with Windows 7 x64 but this was fixed using Greg's (greggar25) excellent step-by-step procedure (see post: https://supportforums.cisco.com/discussion/11492306/usb-console-driver-install-failing).
I am using the driver from this link: http://software.cisco.com/download/release.html?mdfid=282774228&flowid=7442&softwareid=282855122&release=3.1&relind=AVAILABLE&rellifecycle=&reltype=latest
I followed the same procedures I did for Windows 7 and the install goes without a hitch. Reboot and connect the USB cable, opened Device Manager and now I have a COM Port randomly appearing and disappearing with its number incrementing well above 1,000.
A few times while it appeared for a few seconds, I was able to right click on the properties, update the driver and chose Cisco Serial and it settled down but it did not assign a COM port. Then a few seconds later, it starts the disappearing/reappearing thing again.
Anyone have luck getting this to work with Windows 8.1 x64?

Hi,
open Device Manager by simply typing the words on the Windows 8.1 Start Screen. The Search Charm opens and click Device Manager in the displayed list.
In Device Manager a new hardware category, CiscoUsbConsoleWindowsDriver, is displayed. It has two components: the Cisco Bus enumerator and the Cisco USB to Serial adapter. Expanding the Ports hardware category shows a new Cisco Serial port.
or
Look into below
https://supportforums.cisco.com/discussion/11492306/usb-console-driver-install-failing
1) Install the usb console driver\windows 64\setup(x64)
2) Follow the wizard and accept the defaults
3) Restart the computer (the installer usually says it needs a restart)
4) After restarting the computer, plug in the usb cable
5) The computer should say installing Device driver software and fail at the Cisco Virtual Comm Port00
6) Click the Windows button, right click computer, manage
7) Under Computer Management, Click Device Management
8) Go to Ports (COM & LPT)
9) You should see the Cisco Virtual Comm Port00 with a Yellow Exclamation point on it
10) Right Click on the Cisco Virtual Comm Port00 and select Properties
11) Click the Driver Tab
12) Click Update Driver
13) Select Browse my computer for driver software
14) Select Let me pick from a list of device drivers on my computer
15) Choose the Cisco Serial Driver
16) Device Driver is installed successfully, take note of the com port it is using and enjoy.
HTH
Sandy

The drivers won't install

The drivers won't install>Hi
I have a very old MP3 player which I recently started using again. It is around 5 or 6 years old and I think the model name is just Creative ZEN. The model number is DAP-HD005.
Following a hardware failure on my old PC a couple of months ago, I have recently got? a new PC, which runs on Windows 7 (64 bit). The old PC was about 5 years old and ran Windows XP. I have just tried to installm the software that came with the product on the installation disc but it won't load. I have also tried to find anything on theCreative site that will help, but nothing I have downloaded has so far solved the problem. I understand that the player is so old it is unlikely to be supported, but I wondered if there is some generic software that I have missed that I can install which will allow my PC to recognise the player.
Failing this, is gthere a way to make the player work with a Macbook? I tried to install the software on my wife's Macbook, but it wouldn't even try to run.
Any help greatly appreciated.
Thanks
Mark

You should be able to use compatabilty mode for XP to install this [url="http://support.creative.com/downloads/download.aspx?nDownloadId=00098">driver[/url]. It may freeze during the install & not progress but if it does & it lasts longer than 0mins exit it & reboot anyway. Then connect the player. Others have used this method & have been using their older players. I used this method on my Vista comp to install an older nomad player. Download the driver rightclick on the driver choose properties>compatabilty>Xp>then Ok. Then run the file & follow the instructions.

IPhone drivers will not install (windows 7)

Haya there,
I have around 1100 photo's on my iPhone and I was planning to save some on my harddisc so I could free up some space on my phone itself.
Easiest way to do this is plug it in, open the iPhone as a flash drive and drag and drop really.
Now here is my issue:
When I plug in my iPhone it says the drivers have failed to install.
the "Apple Mobile Devive USB Driver" gets installed without any problems. However when it gets to the installing of the iPhone itself it fails.
Meaning, I CAN acces my iPhone trough iTunes just fine. Just not as a flash drive on windows.
Things I have tried:
I've uninstalled both the iPhone and apple mobile device drives, reinstalled them but with the reoccuring same error.
I've uninstalled and re-installed iTunes, downloaded it from the website to make sure I have the newest version.
I've uninstalled and re-installed my USB hub drivers as this was something someone mentioned while I was googling the problem.
I've tried plugging it into different USB ports on my pc, but with the same error when it tried to install the drivers.
I've restarted my pc multiple times in the vein hope that the magic of the restart would cure all.
Noticable:
I've plugged in my phone onto my old laptop (windows vista) and the phone got recognised there without problems. So the problem will be within my desktop, not the phone or cable.
- I use a desktop running Windows 7 Home Premium 64 bit with Service Pack 1
- I'm running iTunes version 11.0.2
I know I can transfer the photo's to my pc using my photostream. At this very moment Im transfering the photo's to my laptop as it is working on there. Where Ill dump them on my external harddisc. But I still want the problem fixed for next time. I should be able to just plug in my phone and get acces to my photo's even when there is no wifi around or when I dont have my laptop at hand.
Thank you in advance for your help

Having more storage in your iCloud account does not expand the storage on your phone. If you don't have enough free space on your phone to update, you'll have to delete some data to do so (such as deleting all your music, then syncing it back to your phone after you update).
Also, backing up your photos to iCloud only allows you to restore them to your phone later if you ever need to, it doesn't allow you to access the photos from iCloud. It also doesn't give you more space on your phone as it only backs up your photos, it doesn't delete them from your phone. If you want your photos in iCloud, turn on photo stream. This will actually take more space on your phone, not less, as you will get a duplicate photo in your photo stream album to the one in your camera roll.
If your storage isn't increasing as you delete data from your phone, try deleting your iCloud backup and backing up again.

Xorg7: fglrx drivers fails with modprobe

Arch installed three days ago from ISO Noodle (after a crash of an old HD), have been actualised up today with xorg7. ATI Radeon 7200LE card is correctly recognised by lshwd as Radeon QD using driver 'vesa', but a display in X flitters in comparison with that in xorg6.9, where it was absolutely steady . Package ati-fglrx is installed correctly. Module 'fglrx' fails loading either placed in modules section of rc.conf or manually invoked by 'modprobe'. Configuration via 'aticonfig' led to inefficient 'xorg.conf' for missing 'fglrx'. Module path in xorg.conf is correct and ATi drivers as well as 'fglrx'module are present. Monitor section of 'xorg.conf' has propper options according the monitor specification. Any idea what is wrong and why 'fglrx' is not recognised when trying to load it? Thank you.

I think brain0 is right on this one. Your card is not offically supported by the fglrx driver as seen in this quote taken from the ati website
"The ATI Proprietary Linux driver currently supports Radeon 8500 and later AGP or PCI Express graphics products, as well as FireGL 8700 and later products. We do not currently plan to include support for any products earlier than this. Drivers for earlier products should already be available from the DRI Project or Utah-GLX project."
The opensource driver mentioned by brain0 should do the trick.
remove your ati drivers that you installed
re-install libgl-dri
install the open source ati driver "pacman -S xf86-video-ati"
change your driver line in xorg.conf to
Driver "radeon"
from what you most likely have right now...
Driver "fglrx"
that should do it!
best of luck!

Drivers Failing to Install

Similar Messages

Maybe you are looking for