Drivers for PCI 4551

These were the following troubleshooting carried out and found in the PCI 4551 S. No. 10FA31A Card
1.Installed the 7.4.1 Traditional Daq (Legacy) drivers and Max version 4.0
2.Opened Test Panel in MAX and run the start acquisition with continuous Mode Channel 0 or Channel 1 with sampling rate 52000 samples/s. During this action the PC hangs some of the time giving an error code 10800, which I found to be a time out error irrelevant to the hanging to PC.
3.Tried step 2 for various sampling rate 100 samples/s, 200 samples/s, 1000 samples/s, 10000 samples/s and 20000 samples/s , found that the same thing happens for all sampling rate.
4.Opened test Panel MAX run the start acquisition with One Shot Mode. With all sampling rate mentioned in step 3. found that the graph display is improper, i.e. graph does not display any plot, but becomes blank.
5.Uninstalled the 7.4.1 drivers.
6.Installed the 6.9.3 Traditional Daq drivers the card is not detected in MAX.
7.The PC Configuration was a P IV with 512 MB of RAM.

Hi,
Have you seen this KB? Although it refers to PXI DSA cards, this information has also been seen to be pertinent to PCI cards.
Instead of restarting, try shutting down your PC and have it stay off
for a minute or two. You could even try unplugging and replugging
your PCI card, or switching PCI slots altogether.
Let me know if this helps solve the problem and have a great day!
Travis W

Similar Messages

Solaris 10 won't boot up "Cannot load drivers for /pci@400.....

This is the error message that I am getting on a Solaris 10 sparc server
scsi: no major number
cannot load drivers for /pci@400.....
Can't load the root filesystem
Type 'go' to resume
{0} ok
Is there a way for me to correct this issue. It looks like I am missing a scsi driver to boot up the server? Is there a way to boot into single user mode, mount the filesystem and rediscover the hardware, etc.....

First i guess you have to verify that you can find the disks with a probe-scsi-all
next you can boot it of a CD-rom/dvd into single-user:
boot cdrom -s
.. or similar into single-user from a jumpstart image:
boot net -s
Then you can mount the root disk under something such as:
/mnt
and rebuild the config with:
devfsadm -R /mnt
be careful if you have a mirrored filesystem though, you don't want to update just one of the mirrors without first breaking the mirror..
.7/M.

64-bit Vista Drivers for PCI Serial device

I've just got an T500 and put Vista 64-bit on it. I've found (I think) all the drivers for it that it needs, except that there are 2 drivers in the Device Manager that show as not installed/needing update they are:
Under Other Devices
- PCI Serial Port
- PCI Simple Communications Controller
Anyone know what divers I should get to get these loaded properly or what devices/capabilities I am loosing because there are no drivers?
Thanks,
George

George, welcome to the forum,
have you tried using ThinkVantage System Update to see if it can automatically find the drivers for you?
Hope this helps
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

Can't find drivers for PCI stuff?

MS 7267 v5.0, Intel 2x1.5 gHz, junkyard machine acquired with no HD, possibly dumped because of a bad HD cable. It's kind of a hobby for me, getting dead machines working and using them. This one, however, has a frustrating problem.
I picked Win XP SP 2 as the OS, the Cover Our Authenticity sticker says it had XP Media Center Edition 2005 on it originally.
With the original HD gone I had to start from zero on drivers. Got several with the usual sorts of digging, including use of MSI's Live Update. Device manager still reported three missing drivers; I got rid of 'PCI Simple Communications Controller' error by replacing the Conexant software modem that came in it with a real modem for which XP had the driver. That leaves just 'PCI device,' and 'Video Controller (VGA compatible),' as missing drivers.
I don't even know what 'PCI device' IS -- the message is still there when there's nothing in any socket so it must be something on the buss -- audio or ???
This seems like a rather low wattage question for this forum, but I spent several hours with Google without coming up with anything useful. Thanks for any help ...

"MB name should be on the board somewhere between the PCI slots ..."
And that's all it took. The MB name is as given in my first post, but I also found "945 GZM6" which Google quickly explained is the Intel chipset for the board. Googling that with "VGA driver" and "PCI device driver" got me the links to manually download the needed drivers from MSI. Display works better, no more ugly messages, and I probably now have audio since the PCI driver was a Realtek one that covered that.
This is my first visit to the world of noname boxes with independent maker MBs. Damn interesting ...
THANK YOU!

I need drivers for PCI device and SM Bus controller

I have a Hp 2000-2d19wm and I downgraded from win8 to win7. Now I'm trying to install the drivers and I can't find them on the HP website. Please help me.
This question was solved.
View Solution.

Hi:
You need this driver for the smbus controller...
http://h20566.www2.hp.com/hpsc/swd/public/detail?swItemId=cp_118001_1
You need this driver for the PCI Dev:
Realtek Card Reader Driver
File name: sp64801.exe

Drivers for PCI-DIO-96

Can someone in NI tell me how to download NI DAQ software for the PCI-DIO-96 that will work with windows vista

Hi
That depends on what LabVIEW version you are using and if you are after DAQmx or Tradition DAQ. The device is still supported in DAQmx 9.1.1 (as per the readme). That version is avaliable for Vista, but you'll have to check if it's compatible with your LabVIEW version. If you want Traditional DAQ the latest version is 7.4.4, but is only officially avaliable for XP/2000. That said I currently have it installed on Windows 7. I've nver actually used them since I reinstalled but they did insall and I have seen them installed on Vista machines as well. Give it a try and see.
Best Regads
David
NISW

Drivers for PCI 6052E and 8.2

OK and sorry in advance, I'm not a Labview wiz. I have a PCI6052E card and I just upgraded ut 8.2. In Measurement and Auto it does not see the card/divice. do I need to update my drivers? and if so where do I get them on the download site? I am running triaditional (legacy) devices. this is because I have several old Vi's that I use all the time. It can see my chassis (SXI-1001 ) and modules but not the card. I think i'm missing something here.
Thanks again
dennis

Any time you upgrade to a new version of LabVIEW, you will need to upgrade the drivers as well, this is so the drivers get linked in to the newest version. You will need to install from the Device Drivers CD (or DVD). As well as installing the traditional drivers, install DAQmx as well.
The drivers should also be available for download from the NI website.

Sil 3512 drivers for Winxp 63bit on w1100z workstation. plz help

I need the drivers for sil3512A onboard sata controller on w1100z workstation for win xp 64 bit. The sun suplement cd contains only the drivers for xp 32 bit. I searched at www.siliconimage.com but they have only the drivers for PCI 3512 sata controller that they don't work. Any suggestions??? plz help

Hello,
If Siliconimage doesn't supply a driver for Windows XP 64-bit you are out of luck.
The systemboard is a K85AE manufactured by Tyan for Sun.
http://www.tyan.com/support/html/drivers%5Fsupport.html
Michael

Windows drivers for SUN Quad PCI card

Hi everyone.
With the risk of being flamed, I have a question regarding drivers for a Sun QUAD network card. I belive it is a X1034A card.
The card is also marked with a label saying: *5015406096836* and a barcode. On another label it sais: QFEPCI
Is there any chance in h**l that this card would function under a Windows system?
Best regards,
Johan Christensson

Hello Ben,
I own the IntraServer LSI5464E which appears to be 501-5406-01 (using the DC21153-AC which was on my card manufactured by Intel not DEC).
I was wrong, the 21153 is a PCI-to-PCI Bridge chip by Intel. I thought it's similar to the DEC PCI Fast Ethernet DECchip 21140.
The 4 Ethernet controllers chips are manufactured by/for Sun.
The datasheet for the LSI5464E is still available, while the drivers aren't.
Michael
When will the deficencies/bugs in the Forums software be fixed ?

Windows 8.1_64 compatible PCI Serial port drivers for M58P (6209)

On the last week I upgraded my Lenovo M58p (model 6088) to Windows 8.1_64 (Enterprise) and encountered the problem in which the drivers for the following were not installed and couldn't be located ....
PCI Serial Port
In the model page there is no information on the PCI Serial port:
http://support.lenovo.com/br/pt/products/desktops-and-all-in-ones/thinkcentre-m-series-desktops/thin...
Thanks
Solved!
Go to Solution.

I found the information about the driver on another topic:
https://forums.lenovo.com/t5/Windows-8-and-8-1/ThinkCentre-
M58p-6234-BR9-Windows-8-eval-build-8250-missing-PCI/m-p/854209#M589
The first link did the trick:
http://support.lenovo.com/en_US/downloads/detail.page?DocID=DS003086
c3amt02us17
Thanks.

Drivers for Sun Floppy under Win 2000 on SUN Pci card.

Hi,
I'm running a Sun Blade 150 with Solaris 8. I have a Sun Pci card with Windows 2000 loaded. When Win2k boots, it asks for drivers for a "sun floppy". I've looked around for these drivers but I can't find them. Can anyone point me to them. Thanks.

Take a closer look at the actual card,
particularly at the central Ethernet chip.
If I recall correctly, it is a DEC DC2115x chipset for 10/100Mbit connectivity,
and should be natively recognized by Linux.
The 501-5406 QFE card, as shown on a 3rd party web site.
Install it and boot your system.
You should know in just a few moments whether it'll work,
or whether the Sun firmware is of any concern.

PCI 4551 for FRA application

This is regarding clarification regarding frequency responce analysis
using NI PCI 4551 add-on card, especially in the singal generation part for
stimulating the unit under test.
1. Is it possible to generate sine, step, ramp and arbitrary waveforms
using this particular card?
2. Ifso what is the range of frequencies that can be possible to
generate using PCI 4551 card?( we may require from 1mHz to 2kHZ)
3. And what is the maximum amplitude of the generated signal for full
scale value?
4. Whether real-time octave analysis for NI DSA software can serve the
purpose of following tests: Frequency response test, Step response test,
Velocity test, Strain Measurement, Linearity Test, Cyclic test.
Or any other software tool is required?

Hi Mallesh,
In response to your questions, I've included my responses. I highly advise referencing the NI-4551 User Manual for more details.
1. Is it possible to generate sine, step, ramp and arbitrary waveforms
using this particular card?
NI-DSA includes functions to generate standard white noise, pink noise, band-limited noise, periodic white noise, single or dual-tone sine, and chirp signals. For step, ramp, and any other arbitrary waveforms you can use NI-DSA to define and generate an arbitrary analog output signal.
There is a good example which ships with NI-DSA that demonstrates how to generate arbitrary waveforms on the NI-4551. You can find this example in the NI-DSA function palette in LabVIEW under Application Examples>>Advanced>>Arbitrary Output Example.
By default, this example outputs a swept sine wave, but you can change the waveform to whatever you need.
2. If so, what is the range of frequencies that can be possible to
generate using PCI 4551 card?( we may require from 1mHz to 2kHZ)
The maximum output frequency you can generate with NI-DSA is 23 kHz. This limit is governed by the maximum output sampling rate of 51.2 kS/s. Because the digital-to-analog converters on the NI 455x DSA devices feature sharp roll-off, anti-imaging filters, you can generate a spectrally pure sine tone up to 23 kHz with minimal quantization noise, so when using the NI 455x devices, you do not need to worry about the output signal becoming choppy or noisy when approaching the Nyquist frequency.
The minimum frequency you can set is 0.1 Hz. This is limited by the finite size of the output buffer and the minimum update rate for the DAC. The output buffer is limited to 4,096 samples, and the DAC must maintain a minimum rate of 1.25kS/s for accurate results.
In Octave Analyzer Mode, when you're inputting a certain frequency, keep in mind the input range differs for each analysis type and the two configurable center frequencies. I've included the frequency ranges for a single channel below.
1/1-octave analysis
center frequency fs=25.6 kHz:
High: 8 kHz
Low: 16 Hz
fs=51.2 kHz
High: 16 kHz
Low: 31.5 Hz
1/3-octave analysis
fs=25.6 kHz
High: 10 kHz
Low 12.5 Hz
fs=51.2 kHz
High: 20 kHz
Low: 25 Hz
1/12-octave analysis
fs=25.6 kHz
High: 10.68 kHz
Low: 11.05 Hz
fs=51.2 kHz
High: 5.34 kHz
Low: 5.52 Hz
3. And what is the maximum amplitude of the generated signal for full
scale value?
The maximum amplitude is equal to the voltage range for the selected output channel.
4. Whether real-time octave analysis for NI DSA software can serve the
purpose of following tests: Frequency response test, Step response test,
Velocity test, Strain Measurement, Linearity Test, Cyclic test.
Or any other software tool is required?
The NI-DSA Real-Time Octave Analysis software add-on for NI-DSA supports fractional-octave analysis for 1/1, 1/3, and 1/12 octave analysis, level measurements, and A-, B-, and C-weighting. You can do octave, level, or both octave and level measurements, and have the additional option of specifying the weighting if required. This is all that can be done in real-time.
To perform a frequency response test, it is preferable to use the swept-sine analysis mode of the NI-4551 rather than a broadband FFT-based frequency response. Swept-sine analysis provides two main advantages over a broadband frequency response measurement in which all frequencies are excited and measured simultaneously. The first is a wider dynamic range. The second is flexible measurements of signal distortion and nonlinearity. For more information of swept-sine analysis, please refer to the NI-DSA Software Manual downloadable off our web site. http://www.ni.com/
For the Velocity test, Strain Measurement, Linearity Test, and Cyclic Test I should ask for more information about each test before attempting an answer. However, to answer your question, there are no methods I know of in NI-DSA that would directly perform these tests. In contrast with that answer, you may be surprised this functionality may be included with a LabVIEW development environment.
Let me know if you have further questions or this does not resolve your issue!
Chad AE
Applications Engineer

Drivers for Belkin F5U220 USB PCI card

I am trying to install Belkin F5U220 USB PCI card into my G4. There are no drivers on the CD or Belkin's website. After installation, I connection Apple mouse. The mouse indicator was lit. But does not work. Where can I get drivers for this PCI card ? I read several posts here that this card worked on many systems. Wondering how it worked... Appreciate any help.

The drivers are built into the operating system.
Does the card appear in your system profiler?
When I plugged in my usb 2 card it just worked. From time to time I had to reset the pmu to get things reset properly but it has been 2 times in 2 years. (lots of 2's in my post, huh?)
Apple seems to have removed the link to the reset of the pmu so I'll give a readers digest.
Open the mac
Touch the power supply case to ground yourself
Remove the battery and check the voltage (3.6V)
Press the pmu button (3/8"square box with a bb size button in the center). Hold it down for a 3 count. Don't press it more than one time or you will mess things up
Replace the battery
Restart the mac with the usb2 card in it.
See if that helps

Drivers for "ne2k-pci" D-Link 10Mbps NIC

Hello!
Can somebody guide me, where I could find the NIC Drivers for "ne2k-pci" i.e. D-Link 10 Mbps Ethernet Card, for Solaris 9????

Hello,
Please provide me the url or information as where
will I find the drivers for following NIC card (for
Sun Solaris 9 Intel OS):
D-Link's -> DFE-538TX
Thanks

2000-412NR Notebook - need drivers for ethernet/networking/pci device

I have no drivers installed ethernet adapter, network adapter, or pci device (not sure what that is). I failed to locate the proper drivers on the hp web page, but I do have hardware ids for these devices:
ethernet adapter:
PCI\VEN_10EC&DEV_8136&SUBSYS_3577103C&REV_05
PCI\VEN_10EC&DEV_8136&SUBSYS_3577103C
PCI\VEN_10EC&DEV_8136&CC_020000
PCI\VEN_10EC&DEV_8136&CC_0200
network adapter:
PCI\VEN_1814&DEV_5390&SUBSYS_1636103C&REV_00
PCI\VEN_1814&DEV_5390&SUBSYS_1636103C
PCI\VEN_1814&DEV_5390&CC_028000
PCI\VEN_1814&DEV_5390&CC_0280
pci device (what is this?):
PCI\VEN_10EC&DEV_5209&SUBSYS_3577103C&REV_01
PCI\VEN_10EC&DEV_5209&SUBSYS_3577103C
PCI\VEN_10EC&DEV_5209&CC_FF0000
PCI\VEN_10EC&DEV_5209&CC_FF00
Please help me find these drivers! Thank you, in advance, for your time.

Hi @Lucky_S
Welcome to the HP Support Forums!
I understand that you are trying to find drivers for some of the devices on your notebook. I am happy to help you with this, but I need to know which operating system you are trying to find drivers for. Please post that information, and I will try to find what is available for you.
Is the Windows Version on My Computer 32-bit or 64-bit?
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

Drivers for PCI 4551

Similar Messages

Maybe you are looking for