Droid 2 Global does not work in Trinidad.

My new droid 2 global worked fine (both data and voice) when I left Houston but will not work in Port of Spain in either voice or data?

MorganB wrote:
For most advanced devices, Data Roaming must be enabled to access data. To check this setting on your Droid 2 Global please follow these steps:
Enabling data roaming may incur roaming charges.
From the home screen, select the applications tab (located at the bottom of the display).
Select Settings.
Select Data manager.
Select Data Delivery.
Select Data roaming.
Enabled when a green check mark is present.
If presented and if agreeable to possible roaming charges, select OK.
For information please see Calling From Trinidad and Tobago.
Wow, so if you get it to work on either GSM or CDMA it is $2.89 per minute! If you are there for some time, get a local SIM, e.g. http://www.mrsimcard.com/s-digicelpos.html. for about 50 cents per min. Note you would need to get Verizon Global to unlock your phone, and you would have a different phone number.

Similar Messages

Droid Razr Maxx HD Data & SMS does NOT work in South Korea

If you are going to South Korea this phone only operates as a "dumb phone" for phone calls ONLY. Data & SMS does not work at all. I contacted Global Support daily for one week with no resolution! I received conflicting information with 2 support folks telling me that the fix was to do a factory reset. So I reluctantly did this and it did not fix anything. It only wasted my time especially re-installing all my apps, etc. Then 4 support folks told me that you should never do this out of the country!! Anyway the last person i spoke to which was a network technician was very honest. He told me that I was "SOL" and he had no idea how to fix this problem. He said that he would have to get some teams together to try to fix the problem. And I was told that I would receive an email with an update. And of course I have not received any email of correspondence from Verizon. Very frustrating...

I found a solution. Okay so with the most recent update Verizon made the switch from sending text messages over their 1x network and moved them to their LTE (and possibly 3g) network, hence the reason they are sending so much faster. Today I was in a classroom that is underground and has terrible reception and noticed that I was getting delivery reports again but that my texts were sending slower, like they used to. I dug around in the phones programing menu and found a new option call "MO SMS over IMS" and it was enabled. Disabling it switches your texts back onto the old 1x network. So if you choose to make the switch, your delivery reports will come back but sending will go back to being a little slower. To get to this menu open up your dialer and type in ##7764726. Next hit send and when prompted with a password type in 000000 and hit verify. Scroll down to SMS/MMS settings and select it. Next scroll to the bottom, select "MO SMS over IMS", and disable it. Now your good delivery reports back!

My Xlite 4.0 software does not work with Jetpack but does work with droid hotspot can this be fixed?

My Xlite 4.0 software does not work with Jetpack but does work with droidx hotspot can this be fixed? I have attached a packet capture for packets from DROIDX with android 2.3.4 marked as XliteWith3G.cap and a packet capture for Xlite with the Jet pack XliteWith4G.cap obiviously same packets coming from Xlite different results depending on WiFi connection.

Hi Vidya,
Thanks for posting your example. You may want to remove your workspace details from the previous posting, or at least update the password on the workspace. I've taken a look at your example and initially couldn't see anything wrong with your tree query. However, when I ran your query in SQL Workshop, it only returned one row, which would explain why you were only seeing one node in your tree! I've updated your query to use a WITH clause, and the tree is now working correctly. I believe you've hit an underlying database bug where the CONNECT BY query is only returning 1 row, when in fact it should return > 1 row. By re-writing the query to use a WITH clause, you can get around the problem.
Regards,
Hilary

Flash player does not work properly on Windows 7 32 bits

Hello,
My flash player does not work properly on Windows 7 32 bits with Firfox and IE8 (lasts versions).
My Flash player version : 10.0.45.2, but I tried with version 9 too, with same problems.
I have tried to uninstall, reboot, reinstall several times, ... witch did not worked.
In fact, it works correctly on some sites, like youtube, but not on some others like :
http://www.dailymotion.com/ => black screen instead of videos, right click gives flash context menu
http://www.canalplus.fr/ => videos does not load, right click gives flash context menu
http://www.myspace.com/ => no audio player, right click gives flash context menu
some games in http://www.kongregate.com/ => black screen instead of games, right click gives flash context menu
I have no problem with shockwave in http://www.adobe.com/shockwave/welcome/
No problem too with flash player on http://www.adobe.com/software/flash/about/
But in the Global Privacy Settings panel (http://www.macromedia.com/support/documentation/en/flashplayer/help/settings_manager02.htm l), I cannot change any settings :
I cannot check boxes,
My changes are not saved.
In most of flash animations, videos, ...,
when I click on parameters, I cannot do anything, even closing.
when I am in full screen mode, the message "press escape to exit...." does not disappear.
Last thing, all those problems was not there when I was on Windows XP, few weeks ago, and appear with my registered Windows 7 premium familly edition, with the same hardware configuration...
Thank you for your help

Hi eidnolb
Thanks for your answer.
This is what I have :
Verify user permissions
I have an administrator account.
I tried (uninstall, install and run) with super-administrator account for same results
Install the most current version.
I am running the latest version (10.0.45.2)
Run the Clean Installer to Fix 3rd Party Flash Player Cleaners
I did not "clean" my computer.
Troubleshoot Pop-up blockers
I have no Pop-up or esle blocker software.
Ensure that Internet utilities do not block Flash Player
I tried (uninstall, install and run) without Avast.
I have windows 7 firewall. I do not know where I can allow ActiveX controls and Flash (SWF) content. I do not see anything relative to ActiveX an Flash in allowed program list.
Fix machine crashes when displaying Flash content
I have no freez or crash.
Using IE, Shockwave Flash Object is Enabled and vs 10.0.45.2
Using FF, I have SWF vs 10.0.45.2 and it is Enabled
I really do not understand !!
Thanks,
Ju'

Insert in Tabular form does not work after the upgrade to APEX 4.0

Hi all,
Thx in advance for looking into the issue.
We are running into following issue when we upgraded APEX 3.2 to APEX 4.02
1) The Tabular form insert does not work.
2) We are fatching the value of the Global variable APEX_APPLICATION.g_XXXX in a procedure and we get null for this value after submit for new row to be inserted.
The tabular form was working fine in APEX 3.2.
The Update and Delete works just fine.
Any help in this regard is highly appreciated.
Thx and regards,
Mahesh

Here is my workaround to get the ADDROW/SUBMIT working again if you have a legacy Tabular Form:
1     PAGE ATTRIBUTES
          JAVASCRIPT
          FUNCTION AND GLOBAL VARIABLE DECLARATION
               var htmldb_delete_message='"DELETE_CONFIRM_MSG"';
2     DELETE BUTTON
          ACTION WHEN BUTTON CLICKED
          URL Target          change to
               javascript:apex.confirm(htmldb_delete_message,'MULTI_ROW_DELETE');
3     ADDROW BUTTON
          ACTION WHEN BUTTON CLICKED
          Action
               redirect to URL
          URL Target
               javascript:addRow();
4     PROCESS
          APPLYMRU (activitated by button ADDROW)
          CONDITION
               never or delete
5     PROCESS
          ADDROWS
          CONDITION
               never or delete
6     CHANGE PAGE TEMPLATE to e.g. THEME 13 One Level Tabs.
7     IF YOU WANT ADD FUNCTIONALITY TO GOTO BOTTOM OF PAGE AFTER ADDROW
     1. In the page footer put <a name="bottom_of_page"></a>
     2. Amend the action when the "ADD" button is clicked to scroll down to the new region by doing the following:
     - edit "ADD" button
     - Go to "Action when button Clicked" section
     - Amend "URL Target" from
     javascript:addRow();
     to
     javascript:addRow();window.location='#bottom_of_page' ;
regards
PaulP

Update process does not work on Tabular Form

Hello,
I have 2 tabular forms on one page, which are using manual update processes.
First form is created using wizard, and therefore works perfectly.
The update process is as follows:
DECLARE
lc_string VARCHAR2(4000);
BEGIN
FOR i IN 1..APEX_APPLICATION.G_f01.COUNT
LOOP
     lc_string := lc_string|| '[' ||APEX_APPLICATION.G_f*03*(i) || '|' || APEX_APPLICATION.G_f*04*(i) || ']';
END LOOP;
--Database processing using the concatenated string here
END;Second form is created manually, using the following code:
SELECT apex_item.checkbox (30,
                           '#ROWNUM#',
                           'onclick="highlight_row(this,' || '#ROWNUM#'|| ')"',
                           NULL,
                           'f30_' || '#ROWNUM#'
                          ) delete_checkbox,
       CATALOG_ID,
          apex_item.hidden (31, CATALOG_ID)
       || apex_item.text (32,
                          LANG,
                          80,
                          100,
                          'style="width:100px"',
                          'f32_' || '#ROWNUM#'
       || apex_item.hidden (33, wwv_flow_item.md5 (LANG, DESCRIPTION)) LANG,
       apex_item.text (34,
                       DESCRIPTION,
                       80,
                       100,
                       'style="width:255px"',
                       'f34_' || '#ROWNUM#'
                      ) DESCRIPTION
FROM V_CATALOGS
UNION ALL
SELECT     apex_item.checkbox
                          (30,
                           TO_NUMBER(9900 + LEVEL),
                           'onclick="highlight_row(this,' || '#ROWNUM#' || ')"',
                           NULL,
                           'f30_' || TO_NUMBER (9900 + LEVEL)
                          ) delete_checkbox,
           NULL,
              apex_item.hidden (31, NULL)
           || apex_item.text (32,
                              NULL,
                              80,
                              100,
                              'style="width:100px"',
                              'f32_' || TO_NUMBER (9900 + LEVEL)
           || apex_item.hidden (33, NULL) LANG,
           apex_item.text
                                           (34,
                                            NULL,
                                            80,
                                            100,
                                            'style="width:255px" ' ,
                                            'f34_'
                                            || TO_NUMBER (9900 + LEVEL)
                                           ) DESCRIPTION
      FROM DUAL
     WHERE :P18_TEMP = 'ADD_ROWS1'
CONNECT BY LEVEL <= 1However, the update process does not work on this form.
I created it using the first one as an example, but with the id's of the second form:
DECLARE
lc_string VARCHAR2(4000);
BEGIN
FOR i IN 1..APEX_APPLICATION.G_f*30*.COUNT
LOOP
     lc_string := lc_string|| '[' ||APEX_APPLICATION.G_f*32*(i) || '|' || APEX_APPLICATION.G_f*34*(i) || ']';
END LOOP;
--Database processing using the concatenated string here
END;Also, both forms are opening in a modal pop-up dialog window.
I use a Dialog Region plug-in for that.
Please advise, what is causing a problem with update?

Sloger,
if this is your tabular form
SELECT apex_item.checkbox (30,
...and this is your update statement
FOR i IN 1..APEX_APPLICATION.G_f*30*.COUNT
...Then you will only ever update records that have been checked. Unchecked checkboxes are not passed back in the global array. You need to have a hidden column with the ID's for the record and loop through that when you are updating/inserting. That is why the built in tabular form has a MRU and a MRD. the MRU loops through the hidden ID column. The MRD loops through the checkbox.
Thanks,
Tyson Jouglet

I have a Serial Number which worked fine on my MacBook Pro but does not work on my desktop PC (Win 7). What is the problem?

I have a Serial Number which worked fine on my MacBook Pro but does not work on my desktop PC (Win 7). What is the problem?

You haven't identified the version so I can't tell if offering you contact options for Adobe Support will be of use to you. But they will likely be your only hope of getting resolution unless you just happen to be using the wrong number as the serial number.
For the link below click the Still Need Help? option in the blue area at the bottom and choose the chat option...
Serial number and activation chat support (non-CC)
http://helpx.adobe.com/x-productkb/global/service1.html ( http://adobe.ly/1aYjbSC )
Phone support | Orders, returns exchanges
http://helpx.adobe.com/x-productkb/global/phone-support-orders.html

Download link does not work

I have purchased Adobe Lightroom4 upgrade online in New Zealand, and the download link in my order does not work. I contacted the Support via Chat and was told to call the 0800 NZ number. I have been on hold for over an hour! Any ideas on where I can get help?

Hi PatriceN46,
Can you try downloading using a different browser. Also, can you provide us with any error messages that you see when you try to download? Have you checked if pop-ups on your browser have been allowed?
I suggest the following document for more info: http://helpx.adobe.com/x-productkb/global/troubleshoot-download-problems.html
You should also hear from other experts on this forum. If you are still unable to solve your problem, let us know, and I'll request a customer support person to get in touch with you.
Thanks,
Preran

I have a manual that contains headings and index entries that contain less than and greater than characters, and . The Publish to Responsive HTML5 function escapes these correctly in the main body of the text but does not work correctly in either the C

I have a manual that contains headings and index entries that contain less than and greater than characters, < and >. The Publish to Responsive HTML5 function escapes these correctly in the main body of the text but does not work correctly in either the Contents or the Index of the generated HTML. In the Contents the words are completely missing and in the index entries the '\' characters that are required in the markers remain in the entry but the leading less than symbol and the first character of the word is deleted; hence what should appear as <dataseries> appears as \ataseries\>. I believe this is a FMv12 bug. Has anyone else experienced this? Is the FM team aware and working on a fix. Any suggestions for a workaround?

The Index issue is more complicated since in order to get the < and > into the index requires the entry itself to be escaped. So, in order to index '<x2settings>' you have to key '\<x2settings\>'. Looking at the generated index entry in the .js file we see '<key name=\"\\2settings\\>\">. This is a bit of a mess and produces an index entry of '\2settings\>'. This ought to be '<key name=\"&lt;x2settings&gt;\" >'. I have tested this fix and it works - but the worst of it is that the first character of the index entry has been stripped out. Consequently I cannot fix this with a few global changes - and I have a lot of index entries of this type. I'm looking forward to a response to this since I cannot publish this document in its current state.

Set up Element 10 as external editor in Lightroom 3, it does not work. What's wrong?

I am using Lightroom 3. Just bought the Element 10 and set it up in Lightroom as external editor. It does not work at all. What's wrong?

Make sure you are linking to the application and not a shortcut. If using Mac OSX you may need to reveal hidden folders.
http://helpx.adobe.com/x-productkb/global/access-hidden-user-library-files.html

MDT - Custom Reference Image does not work with Task Sequence, normal Windows 7 Enterprise Iso media works fine.

Hi,
Our MDT server is acting strange!
I have previously had this system running without problem - i could both capture and deploy computers as is and no changes have been made to mdt.
But my latest capture does not work. When i capture my reference maching in my VM environment it completes without errors and i can import the latest wim file.
When i deploy the tast sequence, it install the custom Wim image, but it ends up with "login" screen as the administrator i have entered for the capture/deploy sequence, but it goes to stop at this point and applications is not installed.
If i change the ISO in the task sequence under Install OS step, to a clean Win7 install media then the capture completes and install applications.
I have also tried to:
Capture reference without password
Capture reference without Windows updates
Customsettings.ini, bootstrap, BDD.log and SMSTS.log to be found here: https://onedrive.live.com/redir?resid=ED5029A20300B814!365&authkey=!AALV1b2ubD0laEE&ithint=folder%2cini
Hope you will be able to assist,
Regards,
Anders

if you have noticed your smsts.log, there is same error multiple -
Executing in non SMS standalone mode. Ignoring send a task execution status message request
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
User did not specify local data drive TSManager
1/23/2015 12:50:37 PM 1656 (0x0678)
Volume A:\ is not a fixed hard drive TSManager
1/23/2015 12:50:37 PM 1656 (0x0678)
Volume D:\ is not a fixed hard drive TSManager
1/23/2015 12:50:37 PM 1656 (0x0678)
Volume X:\ is not a fixed hard drive TSManager
1/23/2015 12:50:37 PM 1656 (0x0678)
Volume Z:\ is not a fixed hard drive TSManager
1/23/2015 12:50:37 PM 1656 (0x0678)
TSM root drive = TSManager
1/23/2015 12:50:37 PM 1656 (0x0678)
We do not find an available volume to store the local data path
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Set a global environment variable _SMSTSNextInstructionPointer=1
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Set a TS execution environment variable _SMSTSNextInstructionPointer=1
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Set a global environment variable _SMSTSInstructionStackString=0
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Set a TS execution environment variable _SMSTSInstructionStackString=0
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Save the current environment block TSManager
1/23/2015 12:50:37 PM 1656 (0x0678)
pszPath[0] != L'\0', HRESULT=80070057 (c:\qfe\nts_sms_fre\sms\framework\core\ccmcore\path.cpp,58)
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Filesystem::Path::Add(sEnvPath, EnvDataFileName, sEnvPath), HRESULT=80070057 (e:\nts_sms_fre\sms\framework\tscore\environmentlib.cpp,639)
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Failed to save environment to (80070057)
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
TS::Environment::SharedEnvironment.saveEnvironment(szPath), HRESULT=80070057 (e:\nts_sms_fre\sms\client\tasksequence\executionengine\executionenv.cxx,842)
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Failed to save the current environment block. This is usually caused by a problem with the program. Please check the Microsoft Knowledge Base to determine if this is a known issue or contact Microsoft Support Services for further assistance.
The parameter is incorrect. (Error: 80070057; Source: Windows)
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
SaveEnvironment(), HRESULT=80070057 (e:\nts_sms_fre\sms\client\tasksequence\executionengine\executionenv.cxx,420)
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Failed to persist execution state. Error 0x(80070057)
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Failed to save execution state and environment to local hard disk
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Start executing an instruciton. Instruction name: Gather local only. Instruction pointer: 1
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Set a global environment variable _SMSTSCurrentActionName=Gather local only
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
Set a global environment variable _SMSTSNextInstructionPointer=1
TSManager 1/23/2015 12:50:37 PM
1656 (0x0678)
what about the mass storage driver in your boot image, is it updated?
Md.Waseem Please remember to click “Mark as Answer” on the post that helps you. Thank you.

Cisco 1841 as PPTP client Does not work

Dear All,
I have Cisco 1841 router running the below roles
1) SSL VPN Server
2) PPTP Server
3) Site to Site Connection with Sonicwall router
I want the router to be configured a pptp client to internet vpn server (so that i will get a fixed public ip )
Once i get this ip address i want to use this connection to accept in coming connection and forward ports to internal host,
I went through below
http://www.mreji.eu/content/cisco-router-pptp-client
https://supportforums.cisco.com/thread/2167562
But it does not work as i do not have the option for the below 2 commands in vpdn-group 2 section.(Please see section in blue)
protocol pptp
rotary-group 4
Please Advise and Help
Regards
Hasan Reza
My Current Config is as below
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.06.09 17:55:23 =~=~=~=~=~=~=~=~=~=~=~=
exit
Gateway#show run |
Building configuration...
Current configuration : 25109 bytes
! Last configuration change at 13:33:57 UTC Sun Jun 9 2013 by admin
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname Gateway
boot-start-marker
boot system flash c1841-advsecurityk9-mz.151-2.T1.bin
boot-end-marker
logging buffered 4096
no logging console
enable secret 5 $1$SciF$TlX1tR5qaG9ZE7pdZHcRJ/
no aaa new-model
dot11 syslog
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 10.236.5.1 10.236.5.20
ip dhcp excluded-address 10.236.5.21 10.236.5.50
ip dhcp excluded-address 172.21.51.2 172.21.51.50
ip dhcp pool ContosoPool
   network 10.236.5.0 255.255.255.0
   default-router 10.236.5.254
   dns-server 213.42.20.20 195.229.241.222
ip dhcp pool DMZ
   network 172.21.51.0 255.255.255.0
   dns-server 172.21.51.10
   default-router 172.21.51.1
   domain-name contoso.local
ip cef
ip domain name contoso.local
ip name-server 213.42.20.20
ip name-server 195.229.241.22
ip name-server 195.229.241.222
ip ddns update method dyndns
HTTP
add http://xxxxxx:[email protected]/nic/update?system=dyndns&hostname=<h>&myip=<a>
remove http://xxxxxx:yyyyy@@members.dyndns.org/nic/update?system=dyndns&hostname=<h>&myip=<a>
interval maximum 0 1 0 0
multilink bundle-name authenticated
vpdn enable
vpdn-group 2
request-dialin
protocol l2tp
initiate-to ip 173.195.0.42
vpdn-group RAS-VPN
! Default PPTP VPDN group
accept-dialin
protocol pptp
virtual-template 1
l2tp tunnel timeout no-session 15
crypto pki token default removal timeout 0
crypto pki trustpoint TP.StartSSL.CA
enrollment terminal pem
revocation-check none
crypto pki trustpoint TP.StartSSL-vpn
enrollment terminal pem
usage ssl-server
serial-number none
fqdn ssl.spktelecom.com
ip-address none
revocation-check crl
rsakeypair RSA.StartSSL-vpn
crypto pki trustpoint TP-self-signed-1981248591
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1981248591
revocation-check none
rsakeypair TP-self-signed-1981248591
crypto pki trustpoint VMWare
enrollment terminal
revocation-check crl
crypto pki trustpoint OWA
enrollment terminal pem
revocation-check crl
crypto pki certificate chain TP.StartSSL.CA
certificate ca 01
(removed the certificate info for clarity)
   quit
crypto pki certificate chain TP.StartSSL-vpn
certificate 0936E1
    (removed the certificate info for clarity)9
   quit
certificate ca 18
(removed the certificate info for clarity)
   quit
crypto pki certificate chain TP-self-signed-1981248591
certificate self-signed 01
    (removed the certificate info for clarity)
   quit
crypto pki certificate chain VMWare
certificate ca 008EDCE6DBCE6B
    (removed the certificate info for clarity)
   quit
crypto pki certificate chain OWA
   (removed the certificate info for clarity)
license udi pid CISCO1841 sn FCZ122191TW
archive
log config
hidekeys
username admin privilege 15 password 7 1304131F02023B7B7977
username ali password 7 06070328
redundancy
crypto isakmp policy 10
encr 3des
authentication pre-share
group 2
lifetime 84000
crypto isakmp key admin_123 address 0.0.0.0 0.0.0.0
crypto isakmp keepalive 10
crypto ipsec security-association lifetime seconds 28800
crypto ipsec transform-set vpnset esp-3des esp-sha-hmac
crypto ipsec transform-set strongsha esp-3des esp-sha-hmac
crypto dynamic-map mydyn 10
set transform-set strongsha
crypto map Dxb-Auh 1000 ipsec-isakmp dynamic XXXXXXXXXX
interface FastEthernet0/0
description Internal Network (Protected Interface)
ip address 10.236.5.254 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface FastEthernet0/1
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
interface ATM0/0/0
no ip address
shutdown
no atm ilmi-keepalive
interface BRI0/1/0
no ip address
encapsulation hdlc
shutdown
interface Virtual-Template1
ip unnumbered Dialer1
peer default ip address dhcp-pool ContosoPool
ppp encrypt mppe auto required
ppp authentication ms-chap ms-chap-v2 eap
interface Dialer1
ip ddns update hostname XXXXXXX.dyndns.org
ip ddns update dyndns
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1450
dialer pool 1
ppp pap sent-username vermam password 7 13044E155E0913323B
crypto map Dxb-Auh
interface Dialer2
mtu 1460
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer in-band
dialer idle-timeout 0
dialer string 123
dialer vpdn
dialer-group 2
ppp pfc local request
ppp pfc remote apply
ppp encrypt mppe auto
ppp authentication ms-chap ms-chap-v2 callin
ppp eap refuse
ppp chap hostname hasanreza
ppp chap password 7 070E2541470726544541
interface Dialer995
no ip address
ip local pool webssl 10.236.6.10 10.236.6.30
ip forward-protocol nd
ip http server
ip http secure-server
ip nat inside source list nat interface Dialer1 overload
ip nat inside source static tcp 10.236.5.12 25 interface Dialer1 25
ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 172.21.51.0 255.255.255.0 10.236.5.253
ip access-list extended internal
permit ip any 10.236.5.0 0.0.0.255
ip access-list extended nat
deny   ip 10.236.5.0 0.0.0.255 172.31.1.0 0.0.0.255
deny   ip 10.236.5.0 0.0.0.255 172.19.19.0 0.0.0.255
permit ip 10.236.5.0 0.0.0.255 any
ip access-list extended nonat
permit ip 10.236.5.0 0.0.0.255 172.19.19.0 0.0.0.255
permit ip 10.236.5.0 0.0.0.255 172.31.1.0 0.0.0.255
ip access-list extended sslacl
ip access-list extended webvpn
permit tcp any any eq 443
logging esm config
access-list 101 permit ip 10.236.5.0 0.0.0.255 172.31.1.0 0.0.0.255
control-plane
line con 0
line aux 0
line vty 0 4
exec-timeout 0 0
login local
transport preferred ssh
transport input telnet ssh
line vty 5 15
exec-timeout 0 0
login local
transport preferred ssh
transport input telnet ssh
scheduler allocate 20000 1000
webvpn gateway gateway1
ip interface Dialer1 port 443
ssl encryption rc4-md5
ssl trustpoint TP.StartSSL-vpn
inservice
webvpn install svc flash:/webvpn/anyconnect-win-3.1.00495-k9.pkg sequence 1
webvpn install csd flash:/webvpn/sdesktop.pkg
webvpn context webvpn
ssl authenticate verify all
url-list "Webservers"
   heading "SimpleIT Technologies NBNS Servers"
   url-text "Google" url-value "www.google.com"
   url-text "Mainframe" url-value "10.236.5.2"
   url-text "Mainframe2" url-value "https://10.236.5.2"
nbns-list "ContosoServer"
   nbns-server 10.236.5.10
   nbns-server 10.236.5.11
   nbns-server 10.236.5.12
port-forward "PortForwarding"
   local-port 3389 remote-server "10.236.5.10" remote-port 3389 description "Server-DC01"
policy group policy1
   url-list "Webservers"
   port-forward "PortForwarding"
   nbns-list "ContosoServer"
   functions file-access
   functions file-browse
   functions file-entry
   functions svc-enabled
   svc address-pool "webssl"
   svc default-domain "Contoso.Local"
   svc keep-client-installed
   svc split include 10.236.5.0 255.255.255.0
   svc split include 10.236.6.0 255.255.255.0
   svc split include 172.31.1.0 255.255.255.0
   svc split include 172.21.51.0 255.255.255.0
   svc dns-server primary 172.21.51.10
default-group-policy policy1
gateway gateway1
inservice
end
Gateway#

Dear All,
I have Cisco 1841 router running the below roles
1) SSL VPN Server
2) PPTP Server
3) Site to Site Connection with Sonicwall router
I want the router to be configured a pptp client to internet vpn server (so that i will get a fixed public ip )
Once i get this ip address i want to use this connection to accept in coming connection and forward ports to internal host,
I went through below
http://www.mreji.eu/content/cisco-router-pptp-client
https://supportforums.cisco.com/thread/2167562
But it does not work as i do not have the option for the below 2 commands in vpdn-group 2 section.(Please see section in blue)
protocol pptp
rotary-group 4
Please Advise and Help
Regards
Hasan Reza
My Current Config is as below
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.06.09 17:55:23 =~=~=~=~=~=~=~=~=~=~=~=
exit
Gateway#show run |
Building configuration...
Current configuration : 25109 bytes
! Last configuration change at 13:33:57 UTC Sun Jun 9 2013 by admin
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname Gateway
boot-start-marker
boot system flash c1841-advsecurityk9-mz.151-2.T1.bin
boot-end-marker
logging buffered 4096
no logging console
enable secret 5 $1$SciF$TlX1tR5qaG9ZE7pdZHcRJ/
no aaa new-model
dot11 syslog
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 10.236.5.1 10.236.5.20
ip dhcp excluded-address 10.236.5.21 10.236.5.50
ip dhcp excluded-address 172.21.51.2 172.21.51.50
ip dhcp pool ContosoPool
   network 10.236.5.0 255.255.255.0
   default-router 10.236.5.254
   dns-server 213.42.20.20 195.229.241.222
ip dhcp pool DMZ
   network 172.21.51.0 255.255.255.0
   dns-server 172.21.51.10
   default-router 172.21.51.1
   domain-name contoso.local
ip cef
ip domain name contoso.local
ip name-server 213.42.20.20
ip name-server 195.229.241.22
ip name-server 195.229.241.222
ip ddns update method dyndns
HTTP
add http://xxxxxx:[email protected]/nic/update?system=dyndns&hostname=<h>&myip=<a>
remove http://xxxxxx:yyyyy@@members.dyndns.org/nic/update?system=dyndns&hostname=<h>&myip=<a>
interval maximum 0 1 0 0
multilink bundle-name authenticated
vpdn enable
vpdn-group 2
request-dialin
protocol l2tp
initiate-to ip 173.195.0.42
vpdn-group RAS-VPN
! Default PPTP VPDN group
accept-dialin
protocol pptp
virtual-template 1
l2tp tunnel timeout no-session 15
crypto pki token default removal timeout 0
crypto pki trustpoint TP.StartSSL.CA
enrollment terminal pem
revocation-check none
crypto pki trustpoint TP.StartSSL-vpn
enrollment terminal pem
usage ssl-server
serial-number none
fqdn ssl.spktelecom.com
ip-address none
revocation-check crl
rsakeypair RSA.StartSSL-vpn
crypto pki trustpoint TP-self-signed-1981248591
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1981248591
revocation-check none
rsakeypair TP-self-signed-1981248591
crypto pki trustpoint VMWare
enrollment terminal
revocation-check crl
crypto pki trustpoint OWA
enrollment terminal pem
revocation-check crl
crypto pki certificate chain TP.StartSSL.CA
certificate ca 01
(removed the certificate info for clarity)
   quit
crypto pki certificate chain TP.StartSSL-vpn
certificate 0936E1
    (removed the certificate info for clarity)9
   quit
certificate ca 18
(removed the certificate info for clarity)
   quit
crypto pki certificate chain TP-self-signed-1981248591
certificate self-signed 01
    (removed the certificate info for clarity)
   quit
crypto pki certificate chain VMWare
certificate ca 008EDCE6DBCE6B
    (removed the certificate info for clarity)
   quit
crypto pki certificate chain OWA
   (removed the certificate info for clarity)
license udi pid CISCO1841 sn FCZ122191TW
archive
log config
hidekeys
username admin privilege 15 password 7 1304131F02023B7B7977
username ali password 7 06070328
redundancy
crypto isakmp policy 10
encr 3des
authentication pre-share
group 2
lifetime 84000
crypto isakmp key admin_123 address 0.0.0.0 0.0.0.0
crypto isakmp keepalive 10
crypto ipsec security-association lifetime seconds 28800
crypto ipsec transform-set vpnset esp-3des esp-sha-hmac
crypto ipsec transform-set strongsha esp-3des esp-sha-hmac
crypto dynamic-map mydyn 10
set transform-set strongsha
crypto map Dxb-Auh 1000 ipsec-isakmp dynamic XXXXXXXXXX
interface FastEthernet0/0
description Internal Network (Protected Interface)
ip address 10.236.5.254 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface FastEthernet0/1
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
interface ATM0/0/0
no ip address
shutdown
no atm ilmi-keepalive
interface BRI0/1/0
no ip address
encapsulation hdlc
shutdown
interface Virtual-Template1
ip unnumbered Dialer1
peer default ip address dhcp-pool ContosoPool
ppp encrypt mppe auto required
ppp authentication ms-chap ms-chap-v2 eap
interface Dialer1
ip ddns update hostname XXXXXXX.dyndns.org
ip ddns update dyndns
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1450
dialer pool 1
ppp pap sent-username vermam password 7 13044E155E0913323B
crypto map Dxb-Auh
interface Dialer2
mtu 1460
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer in-band
dialer idle-timeout 0
dialer string 123
dialer vpdn
dialer-group 2
ppp pfc local request
ppp pfc remote apply
ppp encrypt mppe auto
ppp authentication ms-chap ms-chap-v2 callin
ppp eap refuse
ppp chap hostname hasanreza
ppp chap password 7 070E2541470726544541
interface Dialer995
no ip address
ip local pool webssl 10.236.6.10 10.236.6.30
ip forward-protocol nd
ip http server
ip http secure-server
ip nat inside source list nat interface Dialer1 overload
ip nat inside source static tcp 10.236.5.12 25 interface Dialer1 25
ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 172.21.51.0 255.255.255.0 10.236.5.253
ip access-list extended internal
permit ip any 10.236.5.0 0.0.0.255
ip access-list extended nat
deny   ip 10.236.5.0 0.0.0.255 172.31.1.0 0.0.0.255
deny   ip 10.236.5.0 0.0.0.255 172.19.19.0 0.0.0.255
permit ip 10.236.5.0 0.0.0.255 any
ip access-list extended nonat
permit ip 10.236.5.0 0.0.0.255 172.19.19.0 0.0.0.255
permit ip 10.236.5.0 0.0.0.255 172.31.1.0 0.0.0.255
ip access-list extended sslacl
ip access-list extended webvpn
permit tcp any any eq 443
logging esm config
access-list 101 permit ip 10.236.5.0 0.0.0.255 172.31.1.0 0.0.0.255
control-plane
line con 0
line aux 0
line vty 0 4
exec-timeout 0 0
login local
transport preferred ssh
transport input telnet ssh
line vty 5 15
exec-timeout 0 0
login local
transport preferred ssh
transport input telnet ssh
scheduler allocate 20000 1000
webvpn gateway gateway1
ip interface Dialer1 port 443
ssl encryption rc4-md5
ssl trustpoint TP.StartSSL-vpn
inservice
webvpn install svc flash:/webvpn/anyconnect-win-3.1.00495-k9.pkg sequence 1
webvpn install csd flash:/webvpn/sdesktop.pkg
webvpn context webvpn
ssl authenticate verify all
url-list "Webservers"
   heading "SimpleIT Technologies NBNS Servers"
   url-text "Google" url-value "www.google.com"
   url-text "Mainframe" url-value "10.236.5.2"
   url-text "Mainframe2" url-value "https://10.236.5.2"
nbns-list "ContosoServer"
   nbns-server 10.236.5.10
   nbns-server 10.236.5.11
   nbns-server 10.236.5.12
port-forward "PortForwarding"
   local-port 3389 remote-server "10.236.5.10" remote-port 3389 description "Server-DC01"
policy group policy1
   url-list "Webservers"
   port-forward "PortForwarding"
   nbns-list "ContosoServer"
   functions file-access
   functions file-browse
   functions file-entry
   functions svc-enabled
   svc address-pool "webssl"
   svc default-domain "Contoso.Local"
   svc keep-client-installed
   svc split include 10.236.5.0 255.255.255.0
   svc split include 10.236.6.0 255.255.255.0
   svc split include 172.31.1.0 255.255.255.0
   svc split include 172.21.51.0 255.255.255.0
   svc dns-server primary 172.21.51.10
default-group-policy policy1
gateway gateway1
inservice
end
Gateway#

Assigned F key to play an action does not work. Why? Using cs6 iMac and wireless key board

Assigned F key to play an action does not work to play the action on an image. When the F key is selected it seams to control computer attributes rather than the play action assigned in photoshop. Why? Using cs6 iMac and wireless key board.
Is this a possible preference setting in mac or is it a setting in cs6 photoshop ? Help and knowledge will be appreciated.

*** Moderator Action ***
This networking question has been moved from the Solaris 10 discussion space,
to the Solaris Networking discussion space, for closer topic alignment.
Whereas there may be IPV6 nuances specific to your Solaris 10 environment and to the hardware, this appears to be a discussion that may be more global in effect.

I bought Lightroom 5 and installed it. I was asked for the Serial number and I entered it. But it does not work. Why?

I bought Lightroom 5 and installed it. I was asked for the Serial number and I entered it. But it does not work. Why?

To locate the serial number:
http://helpx.adobe.com/x-productkb/global/find-serial-number.html

Redemption code from Photoshop Elements 12 purchased from Best Buy does not work 'Oops! This code doesn't seem to be active. Please contact the retailer you purchased the card from, or use a different code.' I have an invoice and the pickup notice from

Redemption code from Photoshop Elements 12 purchased from Best Buy does not work 'Oops! This code doesn't seem to be active. Please contact the retailer you purchased the card from, or use a different code.' I have an invoice and the pickup notice from Best Buy. What other information does Best Buy need? What will they do? Will I get a new box? What happened to the days of just typing in a simple s/n?

Redemption Code Help
http://helpx.adobe.com/x-productkb/global/redemption-code-help.html

Droid 2 Global does not work in Trinidad.

Similar Messages

Maybe you are looking for