Droid 4--Global??

Will the Droid 4 be a global phone? I need a 4G phone that will work on Verizon in USA and also in Germany. Is there such a phone yet/soon? Thanks!

I'm replying so other Droid 4 owners see this -- the answer is, it depends on the country you want to use it in. It's possible to use the Droid 4 in countries with wireless networks built on CMDA. If you're planning to travel overseas, it's really important to investigate before you go and not just rely on what the Verizon Wireless Store employees tell you. I know because I did and ended up with a Droid 4 that the store employees assured me would work where I was going -- Sweden -- but it doesn't, except to connect with the Internet via Wi-Fi. The Verizon website has a lot of good info on this - find the International section and use the "Trip Planning Guide."

Similar Messages

  • Class 6 SD card causes problems / lock ups in Droid 2 Global

    My Droid 2 Global phone came with an 8GB SD card and I want to increase it to a 16GB card.  I purchased an adata 16GB Class 6 micro SD card.
    I copied all my data from my 8GB card to my laptop.  I then copied the data from the laptop to the 16GB card.  Put it in the phone and started the phone. 
    The phone had difficulty seeing the SD card and locked up.  Removed battery, reinstalled, restarted.  Similar problem.  Tried various apps and calls - worked (poorly) on some tasks, and locked up on others.
    Formatted the card in the camera and then used the USB cable to move data from the laptop - similar symptoms.
    Formatted the card in the laptop, placed the card in the phone, and used the USB to copy data to the card - same problems.
    Stepped up the process by performing a hard reset on the phone, formatting the SD card, reinstalled apps and tested before adding personal data - still locks up.
    I reset the phone again and put my original 8GB card in - once apps were reinstalled and data was pulled onto the card and everything works normally.
    I really want to use the larger SD card, but I haven't been able to get it functioning..
    I even saw a message somewhere that stated the Droid 2 has problems with Class 6 cards but have found nothing supporting that concept.
    Any ideas?
    Thanks, Grandpa777

    When I replaced the SD in my D2G card with a 16GB one, I researched several cards and class ratings.  Two things seemed to crop up over and over.  Class ratings as an indication of maximum speed are not the same across manufacturers.  Some Class 2 were faster than Class 4 and class 4 faster than Class 6, etc.  Not all, but it was a crap shoot.  Second, Class 10 cards did not work well in all Droids, nor did some Class 6. So I bought the following: 
    SanDisk 16 GB microSDHC Flash Memory Card SDSDQ-016G Class 2.
    It has worked flawlessly for 8 months.  And seems fast enough for my needs.
    My recommendation, for what it's worth: Buy a 16GB SanDisk SD card no higher than Class 4.

  • Droid 2 Global: OGG supported as ringtone, but not as a playable music file?

    I've been having some trouble playing .ogg music in the music player (by trouble I mean it comes back as mostly static), though Android 2.2 is supposed to support ogg natively. Motorola's site on the Droid 2 Global shows something interesting: http://www.motorola.com/Consumers/US-EN/Consumer-Product-and-Services/Mobile-Phones/ci.DROID2-Global-US-EN.alt
    It lists ogg under supported ringtones but not under Playable formates. Huh? What gives? I've even tried different players that are supposed to support ogg on this phone but they do nothing. Is anyone else experiencing the same problem? How is it that the ringtone can play it but the player cannot, even though Android 2.2 supports the formate?

    Oh me of little faith. The replacement phone syncs both ways. I guess there must be some data corruption that persists past a hard reset.

  • Two Droid 2 Global phones - Flaky since software update

    I have two Droid 2 Global phones which were purchased at the same time.  Ever since the last software update, which I believe was the Gingerbread update, these phones have been acting flaky in several ways with various features just shutting down and only a restart of the phone able to make them work again.  Both phones have been having the exact same problems so that leads me to believe it is likely software related.
    1) It quits ringing...even with ringing volume turned all the way up, incoming calls just don't ring. Same with text messages.  Restarting phone fixes the problem.
    2) The camera will take a picture, but when you go to look at it in the gallery, it is just a blank image.  Unless you go look at the gallery, you have no way of knowing the picture didn't take.  Once again, restarting the phone fixes this.
    3)  I have similar issues with the bluetooth.  I sync it up to my car stereo, but sometimes it just won't sync until I restart the phone.
    With the age of these phones, I suspect there are no more software updates on the way from Verizon.  Can anyone confirm that?  Unfortunately, the last software update also prevented <Deleted per the Verizon Wireless Terms of Service.>  Any suggestions on how to get these phones some sort of software update or useful again?  A phone that doesn't ring isn't much use. 
    Message was edited by: Verizon Moderator

        Hi jksoft,
    I know how troubling these difficulties can be especially when it's happening to two lines of service. I extensively researched this trouble in our database as well as Motorola's and was unable to find this as any known trouble. The gingerbread update was the last release for the Droid 2 and no expected changes as of now.
    Are you using the ringtones and notifications that are preloaded in the phone or the ones you have obtained elsewhere? If you haven't tried it yet, please use a notification tone and ringtone that is from the device itself. Let me know if this makes the device work correctly.
    The trouble with camera and bluetooth don't have troubleshooting steps other than doing a hard reset of the device. This will completely wipe out the device but items like contacts and media can be backed up. To complete the reset go to http://bit.ly/rqKDhh and follow the steps for the preferred method. Please keep us posted as we may need to file an investigation with Motorola to review this.
    Thank you,
    MariaC_VZW
    Please follow us on Twitter @VZWSupport

  • Signing up for a new plan with Droid 2 global

    I want to sign up for a new plan (I am not a current verizon customer), switching from Tmobile. The problem is that the phone I want is the droid 2 global, which I cant get in stores until the 29th. I could order online, but I wont be at my home for the next few weeks to pick up the phone.
    There is a verizon store where I am going, but I will not be able to sign up for the new plan from there (due to some un related reasons that you dont need to worry about)
    My main question is, is there a way for me to sign up for verizon's services before monday the 29th, and only pick up the phone from a different store later?

    What is the point in signing up for the services before you have the phone?  Your current T-Mobile device will not work with Verizon.  If you have a Verizon phone already, you can call in or go to the store and ask to have the device activated on month-to-month service and port your number over if you wish.  You'll then have service on your Verizon phone, but no contract, leaving you free to sign a contract and get the Droid 2 at the subsidized price when and where you wish.
    If you don't have a Verizon phone, you'd just be paying for service you can't use, so why not wait until the Droid 2 is available at the store you want to buy it from?

  • Brand new droid 2 global there is a ? in the battery indicator

    hi i just got this droid 2 global last tuesday and today i noticed a ? in the battery indicator today. thinking it was odd i turned off and pulled battery, then put it back in. still there. when i put in the charger it tells me battery is not compatible with the phone. i switched batteries with my gf droid 2 global and the battery worked fine with hers, but her battery when put in mine still showed the ? in the indicator....plz help

    The ? indicates an issue with the battery, from your description it's hard to tell if you may have a bad battery or if it's an issue with the connection to your phone. Your best bet would be to tasked the phone back and get the whole thing replaced. If you do it before the new 14 day return window, you should be able to get a new replacement which would include a new battery. Beyond that, they may try to give you a refurb, which it's just as good as new, but normally doesn't include the battery or back cover. They will probably have you do a factory data reset first (menu> settings> privacy> factory data reset) so you may want to try that, but I have a feeling it won't help.

  • How to use SIM card in Droid 2 Global?

    So I have a Droid 2 Global because it has SIM card capabilities. I called Verizon to allow international roaming. Then I got the unlock code for my phone. Next I put a new-bought SIM card from China Mobile into my Verizon Droid 2 Global.
    However, when someone calls my China Mobile phone number, my phone does not react. The caller hears a prerecorded message that the China Mobile phone number is incorrect or not connected.
    When I call with my Droid 2 Global with the China Mobile SIM card inside, the receiving person sees my Verizon phone number.
    My question is: How do I get my Droid 2 Global to recognize and use my China Mobile SIM card?
    I don't want it to use my Verizon phone number while I am overseas. I like my Verizon service in the U.S., and I plan to return to it.  I just thought the idea of a global phone with a SIM card was to be able to travel to other countries and use another SIM card if need be, and the sales representatives at my local Verizon store sold me this idea of international usage. Other users seem to have no problem. Please inform me of how it works
    Thank you!

    Hi mortb, thanks for your input.
    However, that is not true about SIM cards. You can find accurate information about SIM cards through your search engine or even Wikipedia. SIM cards are meant to be swapped out. SIM cards are used in Europe and Asia more than the U.S. "The SIM card allows users to change phones by simply removing the SIM card from one mobile phone and inserting it into another mobile phone or broadband telephony device" (Wikipedia- SIM cards).
    A SIM card holds the prepaid account value, telephone number, the user's address book, call logs, texts, etc. A lot of websites give the analogy: Say your phone is dead but you need to make a call. You can use your friend's cell phone with your SIM card and call. You won't be using your friend's minutes, but your own because you are using the minutes from your SIM card.
    In my case, I want to use a local cell phone provider to make local calls. Theoretically speaking, I can do so if I swap out my SIM card for a local network's SIM.
    Now Verizon locks all its phones to their Verizon SIM cards, so Verizon phones can only use Verizon SIM cards, but the Droid 2 Global allows you to unlock your SIM, meaning that you are going to put in another SIM card, aka another cell phone service provider.
    So I am confused why I cannot use another carrier's SIM card. Can anyone explain why? Or what can I do to sync my China Mobile SIM to my Droid 2 Global?
    Also referenced: http://community.vzw.com/t5/DROID-2-by-Motorola/Unlocking-Droid-2-Global/td-p/365596

  • Droid 2 Global: symbols attach to last word when typing???

    I have searched and did not see any other topics about this. Has anyone noticed a problem while typing on the Droid 2 Global (in text messages, browser, etc) that if you type special characters/symbols, they attach to the end of the word you previously typed?
    For example, a normal sentence would type like this:
    "Hey I'm running to the store & I'll call you later."
    However, on the Droid 2 Global, it types like this:
    "Hey I'm running to the store& I'll call you later."
    The & automatically attaches to the end of the previous word, even when I press the spacebar before typing it.
    This happens for all symbols I have typed. Sure I can go back and edit it, but it is SUCH a pain to go back and RE-ENTER the space, when I already pressed the spacebar in the first place. I have tried turning "auto-correct" off and it still does this while typing. Does anyone know how to fix this?
    Thanks!

    katiebe wrote:
    I have searched and did not see any other topics about this. Has anyone noticed a problem while typing on the Droid 2 Global (in text messages, browser, etc) that if you type special characters/symbols, they attach to the end of the word you previously typed?
    For example, a normal sentence would type like this:
    "Hey I'm running to the store & I'll call you later."
    However, on the Droid 2 Global, it types like this:
    "Hey I'm running to the store& I'll call you later."
    The & automatically attaches to the end of the previous word, even when I press the spacebar before typing it.
    This happens for all symbols I have typed. Sure I can go back and edit it, but it is SUCH a pain to go back and RE-ENTER the space, when I already pressed the spacebar in the first place. I have tried turning "auto-correct" off and it still does this while typing. Does anyone know how to fix this?
    Thanks!
    This is a well-discussed issue on the Motorola Forums, see https://supportforums.motorola.com/message/316254#316254
    for the same issue on the Pro.
    It will be fixed in the next update, whenever that will be!  Unlike some other stuff though, we can be fairly sure that it WILL be fixed.  The Droid X had the same issue and the update to that did solve the problem.   One solution discussed there is to download Swiftkey (free) which alsosolves  the issue on  the physical keyboard.   Didn't work for everyone though.

  • Droid 2 Global unlock to GSM ((

    Hello there!
    I have a big problem!
    I'm not from USA, I'm from Ukraine.
    I've bought Droid 2 Global A956 on Ebay. Seller said that it's already unlocked. I've received phone after 1,5months (so I couldn't open case cause time expired). And when I put my SIM - phone said "Enter unlock code" ((   I've contacted seller, but he says that phone was unlocked, he lied to me(
    I've tried to buy unlock code on ebay but that didn't worked!!
    Tell me please, how can I unlock my phone? Or where I can get unlock code?? ((

    Thank you.
    But I don't have a privilegue to sell on ebay..
    Tell me why.. why does VZW change friggin unlock codes??
    T-Mobile, AT&T, Sprint does not do that!
    Is changing codes used by VZW to raise an army of haters?
    I have searched the web - and found many people with problem like mine.
    And all of them are speaking bad words in the direction of VZW.
    I like Motorola phones, cause they're exclusive in here, but I don't understand VZW politics!!!
    Why ?????

  • Droid 2 Global Not acting very global

    I just upgraded my Blackberry Storm 1 to a Droid 2 Global.  I worked through Verizon support to ensure the Droid 2 Global is enabled for international use, and used the *228 feature before leaving the US as instructed.  I also had Verizon support unlock the old Blackberry just in case the Droid 2 Global had any issues.
    I am glad I have the unlocked Blackberry!  The Droid 2 should have been a direct device upgrade so I am assuming it is enabled in the countries I frequently travel.  So far the Blackberry is still connecting everywhere with a strong 3G signal.
    The Droid 2 Global on the other hand is spotty.  It connects in Shenzhen, China with no issue, yet can only see a signal in Hong Kong and refuses to connect.  Now in the Philippines the Droid 2 Global works in Manila but fails to find any service in Laguna (25km south). 
    In the mean-time the Blackberry is working just fine with a European global SIM card.
    I cannot figure out if I have a Verizon issue, or if the Droid 2 Global is an inferior device.  Rebooting and fiddling with the network options has no effect.   Has anyone had these problems and figured out how to resolve them?  Verizon e-mail support has not responded either.

    WorldTravel3633 wrote:
    I just upgraded my Blackberry Storm 1 to a Droid 2 Global.  I worked through Verizon support to ensure the Droid 2 Global is enabled for international use, and used the *228 feature before leaving the US as instructed.  I also had Verizon support unlock the old Blackberry just in case the Droid 2 Global had any issues.
    I am glad I have the unlocked Blackberry!  The Droid 2 should have been a direct device upgrade so I am assuming it is enabled in the countries I frequently travel.  So far the Blackberry is still connecting everywhere with a strong 3G signal.
    The Droid 2 Global on the other hand is spotty.  It connects in Shenzhen, China with no issue, yet can only see a signal in Hong Kong and refuses to connect.  Now in the Philippines the Droid 2 Global works in Manila but fails to find any service in Laguna (25km south). 
    In the mean-time the Blackberry is working just fine with a European global SIM card.
    I cannot figure out if I have a Verizon issue, or if the Droid 2 Global is an inferior device.  Rebooting and fiddling with the network options has no effect.   Has anyone had these problems and figured out how to resolve them?  Verizon e-mail support has not responded either.
    I assume that the Global isn't unlocked?   I haven't had issues with the Global (but some have).  If possible, try putting the SIM from the Global into the Blackberry, and see if the connection is still good.  If not, it might just be that the European SIM works with more providers than the Vodafone one  (that, and the costs of calling, are why I always prefer local SIMs!)

  • Droid 2 Global Gingerbread User Guide?

    Is there a User Guide available for Droid 2 Global with the GIngerbread update?
    The info sheet here (http://support.verizonwireless.com/pdf/system_update/droid_2_global.pdf) shows all sorts of "enhancements" but not how to use them.  For example, how do you set up app groups, and what on earth is "Multi-Touch Key-Chording"?
    The link to "Device Manual" (http://support.verizonwireless.com/clc/devices/index.html?p=5567&m=)
    links to the pre-update (Android 2.2 Froyo) manual.
    Thanks!

    DatGyrlVida, if the phone bugs you so much, get a different phone and pay for the change. Your rant and near flaming are not needed here. Your phone frequency problem could be anything, including the junk of apps you probably installed on the Droid interferring with the phone's operations. If you want some assistance on this forum, please describe your phone issues professionally and we can see if we can resolve it together.
    And no, I do not work for VerizonWireless.
    My experience with my Droid 2 Global is that I had it replaced three times under warranty due to loss of 3G connection, and a reboot could not resolve it. I since then purchased My Backup Pro app to do a complete phone backup, so if I need to replace the phone again (to my SD card or private cloud), I can reimage it. Plus, whenever I install a new app, I do a full backup beforehand so if the app corrupts my phone (or interfers with any phone operation like reception), I can do a reimage on the phone to the previous working state. Uninstalling the offending app does not necessarily remove the junk from its installation. Something for you to consider...

  • Droid 2 Global Issues - notif. bar and incoming calls

    Ok, I've had my Droid 2 Global for about a year now, and for the most part it has been fine. However, on the latest couple of updates, some really annoying "features" have come up. On the current update, the notification bar disappears randomly. Not known cause. Also, if the notification bar disappears, when I receive and incoming call, it doesn't display the "answer call" screen, showing the contact. This makes it difficult to answer the call, especially when the screen is locked. I have to go unlock the screen, and go to a screen like I'm going to call someone, and THEN I can see who is calling and maybe answer. If it hasn't gone to VM already. This is really stupid - first and foremost, this thing is a FREAKING PHONE. I should be able to answer a call.
    Frustrated. Any ideas/help?
    Thanks,
    -Dirv
    Details
    =============
    System version: 4.5.629.A956.Verizon.en.US
    Android version: 2.3.4
    Kernel version: 2.6.32.9-g177d714 mcbk83@il93lnxdroid01 #1
    Build number: 4.5.1_57_D2GA-59

    Ok, I've had my Droid 2 Global for about a year now, and for the most part it has been fine. However, on the latest couple of updates, some really annoying "features" have come up. On the current update, the notification bar disappears randomly. Not known cause. Also, if the notification bar disappears, when I receive and incoming call, it doesn't display the "answer call" screen, showing the contact. This makes it difficult to answer the call, especially when the screen is locked. I have to go unlock the screen, and go to a screen like I'm going to call someone, and THEN I can see who is calling and maybe answer. If it hasn't gone to VM already. This is really stupid - first and foremost, this thing is a FREAKING PHONE. I should be able to answer a call.
    Frustrated. Any ideas/help?
    Thanks,
    -Dirv
    Details
    =============
    System version: 4.5.629.A956.Verizon.en.US
    Android version: 2.3.4
    Kernel version: 2.6.32.9-g177d714 mcbk83@il93lnxdroid01 #1
    Build number: 4.5.1_57_D2GA-59

  • Droid 2 global doesnt work after new update

    I have a droid 2 global but it is prepaid and now after the latest update it doesnt work. Can verizon replace my prepaid phone or do I have to purchase another phone?
    <post moved to the "Droid & Droid 2" space from the "My Verizon" space for more exposure.>
    Message was edited by: Verizon Moderator

    Currently, I am not showing a way to remove the Street View for Google Maps application from the device. If you are adamant about removing this feature, the next available option would be doing a factory reset. This can be completed through the following steps:
    Factory Reset option 1
    From the main screen, touch menu tab
    Touch Settings
    Touch Privacy
    Touch Factory Data reset
    Touch Reset Phone
    Touch Erase Everything
    Warning: This will erase all data from your phone, including:
    Your Google account
    System and application data and settings
    Downloaded Applications
    It will not erase: Current System software and bundled applications; SD Card files, such as music or Photos
    Factory Reset option 2  - Warning this will reset device back to original factory settings.
    Turn off the phone
    Power on phone while pressing "X" key on qwerty keypad - release "X" and power key after you see Motorola batwings.
    You should now see an "!" in a triangle with Android guy
    Press the "Search" key on qwerty keypad to enter factory menu, this will unhide the menu and show the following options
    Reboot system Now
    Apply sdcard:update.zip
    Wipe Data/Factory Reset
    Wipe Cache Partition
    Use Vol Up / Vol down to navigate to "wipe data/factory reset" and then use Camera side key or Menu key to select "wipe data/factory reset"
    Use Vol Up / Vol down to navigate to  "Yes delete all user data" and then use Camera key to select "Yes - delete all user data"
    Wait for operation to complete (maybe 1 minute or so) and then press camera key to select "reboot system now"

  • Droid 2 Global screen problems, vibrate problems, basically just a lot of problems?

    So, I've had my Droid 2 Global (Gingerbread 2.3.4) for about a year and a half, and ever since I got it I've had problems with the touchscreen. I have not rooted or customized the phone in any way, nor have I ever damaged the phone or gotten it wet.
    Windows will open by themselves, the music player and maps constantly open by themselves and drain the battery, any time I'm trying to send a text the keyboard goes haywire and will send "wttttttyuuuuttt" and nonsense like that to anyone on my 'recently texted' list. It takes about 10 minutes to send a simple text because the screen won't stop shaking and displaying random letters. It's not just when I'm touching it either. I've had it call random numbers and vibrate for no reason when I'm asleep and it's on my bedside table.
    I took this phone to the verizon store when I first got it, they "fixed" it, but an hour later it was back to being glitchy. I took it back, they told me to do a hard reset, it didn't help at all. I tried restarting the phone in safe mode several times (the most recent time being this morning) but the screen shaking and random apps opening issues are even worse in safe mode than in regular mode.
    I was wondering if anyone else had these kind of problems, and if so, how would I go about fixing them? Honestly I'm planning on getting rid of this phone in a few weeks but if there's anything I've overlooked I want to check it out.

        Hello hammerofasgard! Love the handle, by the way. I'm a Thor fan, too!!
    Sounds like you've been having some very frustrating and inconvenient issues with your Droid 2 Global. I have one that I still use but have never seen the behaviors you've described (except for the battery drain, but that's something that was easily managed by just keeping a charger handy). You mentioned having taken the D2G to one of our retail locations for assistance, and that the device reverted to it's previous behavior an hour later.
    I'm curious to know if the reps on our store performed a master reset (taking the device back to factory settings). If they did, did you have any of the same apps or settings restored to the device during that hour?
    Dion M.
    VZW Support
    Follow us on Twitter www.twitter.com/vzwsupport

  • Droid 2 Global does not work in Trinidad.

    My new droid 2 global worked fine (both data and voice) when I left Houston but will not work in Port of Spain in either voice or data?

    MorganB wrote:
    For most advanced devices, Data Roaming must be enabled to access data.  To check this setting on your Droid 2 Global please follow these steps:
    Enabling data roaming may incur roaming charges.
    From the home screen, select the applications tab (located at the bottom of the display).
    Select Settings.
    Select Data manager.
    Select Data Delivery.
    Select Data roaming.
    Enabled when a green check mark is present.
    If presented and if agreeable to possible roaming charges, select OK.
    For information please see Calling From Trinidad and Tobago.
    Wow, so if you get it to work on either GSM or CDMA it is $2.89 per minute!   If you are there for some time, get a local SIM, e.g. http://www.mrsimcard.com/s-digicelpos.html. for about 50 cents per min.  Note you would need to get Verizon Global to unlock your phone, and you would have a different phone number.

  • Liberar un Droid 2 Global para Republica Dominicana???

    Saludos, no hablo ingles y soy de Republica Dominicana, y me trajeron un Motorola Droid 2 Global de Verizon, quisiera saber si lo puedo desbloquear, o si se puede usar con un SIM de Claro.
    Dejenme saber por favor... Gracias!

    Hola gregory_veras,
    El SIM de los telefonos globales the Verizon Wireless puede ser desbloqueado por nuestro equipo de soporte tecnico global llamando al 908-559-4899 solo si se cumple con los siguientes requisitos:
    ·                                 El dueño del telefono debe ser un cliente actual de Verizon Wireless.
    ·                                 El telefono a desbloquear debe estar activo en una linea de servicio de Verizon Wireless.
    ·                                 La linea de servicio debe estar activa un minimo de 60 dias.
    ·                                 La cuenta de servicio debe estar al corriente con los pagos un minimo de 60 dias.
    ·                                 Solo puede ser desbloqueado un SIM por linea activa cada 10 meses.
    AntonioC_VZWSupport
    Follow us on Twitter at www.twitter.com/vzwsupport

Maybe you are looking for

  • For Refreshing a table display in ALV when data is chngd in maintainance vi

    Hi All, I am displaying the fields of a Ztable in a ALV report. A maintainance view call button is attached to that report through which data of Ztable can be changed.Prolem is that when after changing the data when I return back to report, changes a

  • How to get a specific value from a mult-value returning procedure

    Hi, We're using Oracle 11.1. I have a procedure that I'm calling in a query that looks like the following:    PROCEDURE tcmenc1_clean_codes (       p_icd_code_1_source   IN     VARCHAR2,       p_icd_code_2_source   IN     VARCHAR2,       p_icd_code_3

  • Regarding JAI

    hai, I want to run a program using JAI...I have installed it and have set the claspath also..but when i run the program it results in error.... symbol : method add (javax.media.jai.widget.ScrollingImagePanel) location: class RemoteImagingTest add(new

  • Remove "Export Spreadsheet" button in result list for search on BP in WebUI

    Hi everybody, Could someone tell me how to remove the standard button "Export spreadsheet" from the result list of a search for Customer and Account in the WebUI? Is it possible to do this by using the transaction BSP_WD_CMPWB "BSP WD Component Workb

  • Need TB1300 Course material

    We would like to attend TB1300 SAP Business One - Software Development Kit, but this course scheduled only in July, if anybody(who attended this course) interested in sharing with us about your knowledge & course material would be appreciated. Thanks