Drop connection from AP1550 - WLC8500

Hi everyone
I´m hopping you can help with a problem I´m experimenting with a wireless lan. I´m working with the WLC 8500 and 7 AP 1550; we already setup this equipments since last year, working without a problem, because there was not much traffic (This WLAN is working on a university). a few months ago we began to experiment a few drop connections from one AP, but 2 days ago, all AP are having drop connection all the time, with latency of more than one thousand miliseconds.
We checked the setup again, and all seens fine, the only thing that we are not sure is about the "load profile" from the 2.4Ghz frecuency, is changing continiously from passed to failed.
All the AP are working as root (no mesh network), all of them are in local mode, they are working at 2.4Ghz, all AP are using the same VLAN (just one).
What can we do with this issue?
Thanks and best regards
Alvaro Rugama

Hello Alvaro ,
As per your query i can suggest you -
Check the vlan settings as well as log-profile logging is turned on.
For more information refer to the link-
https://supportforums.cisco.com/docs/DOC-1176#Access_Points__20xxx_
http://www.cisco.com/en/US/docs/wireless/controller/7.0/configuration/guide/c70rrm.html

Similar Messages

  • New Airport Extreme (6th Gen) Dropping Connection from Time to Time.

    Problem:
    6th Generation Airport Extreme drops connection intermittently at random times.
    Set Up:
    6th Generation Airport Extreme (main router - no hard drive/not a time capsule) located center of house on the main floor. 2 Range extenders each approximately 30+ feet away from main router. First range extender (Airport Express - newest generation) located on the third floor parallel to main. Second range extender (Airport Express - new generation) is located at the end of the kitchen (main floor).
    Main Router is connected straight from a Motorolla Surfboard modem on a foyer table at the center of the house.
    Range extenders connected to Main Router wirelessly and at wall outlett height.
    Previous Setup:
    Same setup as above but, with the 5th Generation Airport Extreme instead of the 6th Generation.
    Firmware:
    All current versions.
    Devices:
    1 SONY VAIO VGN-FW490J
    HP Notebook G60
    Several WEMO outlets
    1 iPad Mini
    1 iPad 2
    1 iPhone 5
    1 Motorolla RAZR MAXX
    Macbook Pro
    iMac (wired from main router on foyer table)
            Note: All of these routers/range extenders/modem/computers are plugged into surge protected outlets.
    Notes:
    With the new Airport Extreme my family and I have been experiencing intermettent connection drops. The amber light on the main router turns on and within a few minutes turns green and connection resumes again. This has been happening for a few days now ever since I purchased the new router. This has not happened before with the 5th generation router, which I donated to our church.
    I have not exchanged the product yet. I will be initiating a Complete Power Recycle after some suggested solutions in a bit. I have contacted my Internet Service Provider (Comcast) for a line check and found no problems.
    Has anyone found any solutions to resolve the intermittent connection drops? Is reverting to the previous firmware going to solve this?
    I would like some insights before trying to do all this. Thank you all for your time.
    P.s.
    I've done a detailed post since posts like these is frequently asked questions on set-up, devices, connections, etc:

    Update:
    Before I went to exchange my 6th Gen Extreme, I ran through all possible solutions from complete power recycle to no devices connected. I even went out of my way to my cousin's house to test it out. The same problem still kept coming.
    I was able to exchange my 6th Gen Airprt Extreme with another 6th Gen Extreme the other day. I set it up how the instructions told me and within an hour it did the exact same problem as the previous 6th Gen Extreme. I gave up and decided to get the ASUS RT-AC66R (ASUS RT-AC66U is the same, just the 'R' is Best Buy's model.)
    The ASUS router is just as great as the 6th Gen Router. You can actually get it down to $180 by price matching to Amazon. The ASUS router has 3 antennas that you can adjust according to where the signal is used more. I pointed them more towards the backyard, upstairs, and the living room. The range is by far better than the Extreme because of this. I was able to drive down a good block (3-4 houses down) and still connected to my router. Also it has 2 USB ports which was fantastic for me so I can plug in my external hard drive and a non-wireless printer. It has many more features that I really liked that I didn't even know was possible. The router utility interface is a bit confusing at first but, it's pretty easy once you get the hang of it.
    Some features that I liked with the ASUS was the ability to have multiple guest network with time limits. 3 for 2.4gHz and 3 for 5gHz. I think that Airport guest accounts are only allowed 2.4gHz but not a 5gHz. Though I only needed 1 for each but, I can see this working well for businesses.
    Another feature is traffic manager. I am able to set specific bandwith for different types of use such as, high priority 80%-100% bandwith for gaming, medium priority badwith 70%-90% for HD media streaming/data transfer, and 50%-80% low bandwith for casual web surfing. It also has it's own "beamforming" so that data isn't free roamed.
    Lastly it has AiCloud sync which is basically like having a hard drive into your router but, much like having a Dropbox at the same time.
    More or less I think I'll stick with the ASUS router rather than going with the new Airport Extreme. I think that it's more on firmware issue than it is hardware. If you are not willing to switch to another brand and want to keep staying with Apple, I recommend going back to the 5th generation until a new firmware or rebuilt 6th gen extreme is out.
    I have not found any problem with the ASUS router and no intermittent connectivity issues.
    Now I am not trying to make you buy the ASUS router. I'm merely expressing how great the product is.
    I do have 60 days from Best Buy return policy to try out the ASUS (and report of any malfuntions) and if within that time a new firmware is out for the Extreme. I highly doubt I'll go back to the extreme though.
    Hope this helped!!

  • Apple TV3 dropping connection from iTunes...

    Hi there,
    I've read a lot of issues on the same thing but I wonder if anyone is having the same issue as me.
    Thinking it was a hardware problem I secured a replacement from the store but I'm having the same issue.
    I have a PC, Windows 8
    BT Infinity (with their home hub, I'm UK based)
    My Apple TV is wired directly to the hub (I have also adjusted the settings to give the Apple static IP addresses, I've also tried it with automatic IP)
    If I boot everything up from scratch the Apple TV will play both music and my movies (both my DVD rips and those purchased from iTunes store and downloaded to the PC).
    However, let's say when I've done the above I decide to watch a movie that is on the PC, it works and I can watch the full film or even a TV program.  Then I decide I want to watch another film after viewing that one, that's when I get the spinning wheel.  The Apple TV will recognise my iTunes library and display the movies but unless I watch something on the cloud I cannot view what's on my PC hard drive.  Then after a bit the Apple is telling me to turn on home sharing.  It already is on and my PC has no sleep settings activated, I turned them all off so unless I power down nothing will enter sleep mode or even powersave.
    I then have to reboot the PC and open iTunes again.
    Like I mentioned I've taken the first one back for an exchange, the same problem persists.  I've also been on the phone to Apple who advised to power everything down for 5 minutes then turn the router back on followed by the Apple then the PC.  That worked, so I then left it for 5 minutes and then the problem happened again when I decided to watch a film that I put on my PC hard drive.  It seems that I have to choose what I want to do quickly but it wont work with further requests after something is played. 
    I am using the inbuilt virus checker that comes with Win 8 (Elements I think it's called) and I use Windows Firewall.  I have tried creating a rule to allow iTunes to connect out on the firewall settings but this did nothing.  I've tired automatic IP addresses and now trying static ones but again, no joy.  Bonjour has been uninstalled, reinstalled, opened up connections in the firewall, basically everything I've read on this issue I've done.
    I read somewhere about turning off the Dolby Stereo, and yes, you guessed it, nothing corrected it.
    Has anyone had this problem exactly and any idea how to overcome it.  Apple have suggested a clean reinstall of my PC, so I tried it, wiped everything and started again.  Nothing, so I tried it on my laptop which has Windows 7 and it seems it's not localised to just one specific version of Windows.
    Getting a bit fed up now! 
    As a last ditch attempt I also checked the serial number to see if it was an old unit that needed to be replaced but it's not.  Oh, and I have also tried wireless and wired.  That didn't change anything.
    One interesting thing though, when looking at the settings for the BT Home Hub and looking at devices, when I know the Apple TV is connected it's showing as not connected.  It appears as though it is dropping connection after it has perhaps synced the whole film from the PC.  I can't think of a way to force it to stay connected.
    Any suggestions?

    UPDATE
    This is now resolved, not with the use of the Homehub though.
    After another conversation with Apple they asked me if the Youtube app on the TV works, which it does then there's a problem elsewhere!  Therefore Apple think there's an issue with the hub or the home network.  They also asked me to try something on the hub called Port Forwarding.  However, because that the hub isn't an Apple product they are not allowed to advise me on tinkering with the settings.  But did suggest to Google a website called port forwarding. 
    Having a look at that I tried what it suggested by connecting to the BT Homehub, you guessed it, that didn't work either.  I called BT who advised that their technical help team that would deal with this has been disbanded and the person I spoke to gave me the port forwarding suggestion on Google.
    At this stage I had had enough and after reading a few more bits of feedback I then looked at replacing the hub with something I could buy myself.  This led me to Amazon where I purchased the ASUS RT-N56U and a modem to go with it.  I ripped out the hub and linked the modem to the line in the wall and the router to the modem, I had to bridge the router to the modem and after that was done I set up the wireless.
    I'm now very pleased to say that it works, everything is syncing as it should do and the speeds of my downloads have also increased.  So far no issues at all.  I also have a constant connection to the PC and can view as many films as I want that are downloaded to the PC.  No lagging, no problems at all.
    Bit of an expensive solution but the modem and router I bought can also replace a Virgin one should I change suppliers in the future.
    If you follow this solution and are doing it the same with BT just Google the username for the hubs as it's the same for everyone, you can get that username from the hub if you connect to it but if you're like me and didn't think of that all the solutions you can google.  I used the CD's that came with the items and I had it all set up and running in 5 minutes.  If you do purchase the RT-N56U don't forget you need a modem, as that bit I forgot about and then had to order that via Amazon as well.
    That's really all you need!

  • Drop connections from specific hosts/nets

    Hi all.
    I'd like to completely drop connections coming from some specific die-hard UCE mass mailers who keep hammering my mail system.
    I blocked their IP ranges in my RAT with connection behavior set to either Reject or TCP refuse, but they keep trying anyway.
    Both my boxes get about 50 connections/min night and day from these companies (even if they get rejected on the first box with a 554 error code, i.e. permanent failure, they try on the next box anyway, and try and try again...)
    So, is there a way to do this with AsyncOS at the IP or TCP layer ?
    Or do I need to do this on my firewall ?
    TIA.
    PS: I miss Ironportnation. It was so much better than this...

    Yeah? OK, I guess I'll block them at the firewall level.
    Since I'll end-up droping the connection anyway, it somewhat makes sense to drop it as early as possible.
    It would have been nice to keep all mail-related configuration in the same place though.

  • Dropping connection from inbound mail

    About 2 days ago our server stopped being willing to receive messages from one of our client's outbound servers. Sometimes they receive a message bounceback immediately, other times in several hours or overnight. No changes were made to our server or mail configuration and we are successfully receiving messages from numerous other folks to the same address without issue.
    Included below is an excerpt of the mail.log file showing an attempted connect to our server and then "immediate" loss of connection. I have tried restarting the mail service and rebooting the server (10.5.4). Does this look like an issue at our end or their's? If ours, any thoughts on cause and cure? Note also that we're behind a Cisco Pix, but no changes have been there for a considerable period either and the "no fixup protocol smtp 25" is set. We are not running spam filtering.
    Any help or suggestions would be much appreciated!
    Thanks,
    Brian
    Sep 10 10:50:33 myserver postfix/smtpd[24513]: connect from bean.electric.net[72.35.23.29]
    Sep 10 10:50:33 myserver postfix/smtpd[24513]: lost connection after CONNECT from bean.electric.net[72.35.23.29]
    Sep 10 10:50:33 myserver postfix/smtpd[24513]: disconnect from bean.electric.net[72.35.23.29]
    Sep 10 10:50:42 myserver postfix/smtpd[24515]: connect from bean.electric.net[72.35.23.29]
    Sep 10 10:50:42 myserver postfix/smtpd[24515]: lost connection after CONNECT from bean.electric.net[72.35.23.29]
    Sep 10 10:50:42 myserver postfix/smtpd[24515]: disconnect from bean.electric.net[72.35.23.29]
    Sep 10 10:54:02 myserver postfix/anvil[24466]: statistics: max connection rate 4/60s for (smtp:72.35.23.29) at Sep 10 10:50:42
    Sep 10 10:54:02 myserver postfix/anvil[24466]: statistics: max connection count 2 for (smtp:72.35.23.29) at Sep 10 10:50:32
    Sep 10 10:54:02 myserver postfix/anvil[24466]: statistics: max cache size 1 at Sep 10 10:46:27
    Here's a bounceback message as forwarded by the client to a different account...if this helps.
    Subject: Mail delivery failed: returning message to sender
    This message was created automatically by mail delivery software.
    A message that you sent could not be delivered to one or more of its
    recipients. This is a permanent error. The following address(es) failed:
    [email protected]
    retry timeout exceeded
    ------ This is a copy of the message, including all the headers. ------
    ------ The body of the message is 18682 characters long; only the first
    ------ 16384 or so are included here.
    Return-path: <[email protected]>
    Received: from 1Kd7Hz-0008HS-T4 by worden.electric.net with emc1-ok (Exim 4.69)
    (envelope-from <[email protected]>)
    id 1Kd7Hz-0008J3-Un
    for [email protected]; Tue, 09 Sep 2008 10:46:07 -0700
    Received: by emcmailer; Tue, 09 Sep 2008 10:46:07 -0700
    Received: from [66.38.130.1] (helo=cgaowa2.cga-canada.org)
    by worden.electric.net with esmtps (TLSv1:RC4-MD5:128)
    (Exim 4.69)
    (envelope-from <[email protected]>)
    id 1Kd7Hz-0008HS-T4
    for [email protected]; Tue, 09 Sep 2008 10:46:07 -0700
    Received: from CGAEXCH.cga-canada.net ([10.1.10.151]) by
    cgaowa2.cga-canada.net ([10.1.10.155]) with mapi; Tue, 9 Sep 2008 10:46:06
    -0700
    Content-Type: multipart/mixed;
    boundary="000_035F790236EE4A418923913476257A9801D869F7DBCGAEXCHcgacan"
    From: Cleint <[email protected]>
    To: "[email protected]"
    Date: Tue, 9 Sep 2008 10:46:05 -0700
    Subject: FW: New Notices for You
    Thread-Topic: New Notices for You
    Thread-Index: AckSGnOB27CoC/P/TSOWwemQb6Es9wAiVymA
    Message-ID: <[email protected]>
    Accept-Language: en-US
    Content-Language: en-US
    X-MS-Has-Attach:
    X-MS-TNEF-Correlator: <[email protected]>
    acceptlanguage: en-US
    MIME-Version: 1.0
    X-Outbound-IP: 66.38.130.1
    X-Env-From: [email protected]
    X-Virus-Status: Scanned by VirusSMART (c)
    X-Virus-Status: Scanned by VirusSMART (s)
    --000_035F790236EE4A418923913476257A9801D869F7DBCGAEXCHcgacan
    Content-Type: text/plain; charset="us-ascii"
    Content-Transfer-Encoding: quoted-printable
    Message was edited by: Brian Friedrich

    Always fun to answer your own question. It turns out that the application of the "no fixup protocol smtp 25" to the Pix seems to have resolved this issue. Very odd I must say, because the "fixup" had been active since setting the unit up years ago... Nonetheless, mail from this client is coming through now (including the backlog...oh joy).

  • WRT110 Drops connection

    Good day to all!
    My WRT110 drops connection from time to time, once or twice at random per evening + when one of my other PCs boot up.
    I have a Synology DS209 NAS wired, a broadband internet connection (through a modem) and several PCs on wireless. In this situation the problem is reproducable: I have connection on PC 1, and when I boot any of the other PCs, the connection drops for 5 minutes (both internet and to my NAS) on all connected systems. After these 5 minutes, every system connects again. All systems have DHCP switched on, and all systems have different IPs just before this happens. I have done a "back to factory defaults" and power cycles, but the problem stays.
    When I look with Vistumbler (or NetStumbler), I see drops from 90% signal to 0% once per -say- 5 minutes and irregular.
    Do I have a defective router?
    Thanks for an answer....
    Drogreder
    Solved!
    Go to Solution.

    Turn Off IPv6 Support in Vista
    Go to Network Connections folder (click on Start button, then right click on Network, select Properties, then click on “Manager network connections” on Tasks pane).
    You should see various LAN, wireless, Bluetooth, high speed Internet, and other network connections available on the Vista computer with the network adapter description. Right click on the network connection that you want to disable the IPv6 interface and select “Properties”.
    Click “Continue” on User Access Control permission request prompt.
    Clear the check box next to the Internet Protocol version 6 (TCP/IPv6) component in the list under “This connection uses the following items” box.
    Click OK when done.
    taken from http://www.mydigitallife.info/2007/09/09/disable-and-turn-off-ipv6-support-in-vista/
    The Search Function is your friend.... and Google too.
    How to Secure your Network
    How to Upgrade Routers Firmware
    Setting-Up a Router with DSL Internet Service
    Setting-Up a Router with Cable Internet Service
    How to Hard Reset or 30/30/30 your Router

  • E4200 dropping connections

    my e4200 updated with latest 1.00.1 firmware is constantly dropping connections from the outside to existant lan servers running low traffic services when my machine is using torrent or internet gaming.( call of duty modern warfare )
    anyone else with that behavior ?
    when will cisco fix this ?
    cheers

    lordgrinz,
    I believe you. I just wanted to point out there are many users not experiencing issues (given their needs and the features they use). Given this, there are perhaps specific scenarios / setups  under which the issues occur, some of which may not be Cisco's fault (software or hardware conflicts with equipment from other manufacturers).
    For example, when I used my Rosewill wireless utlity (came with my 802.11n USB adapter), it conflicted with something that caused the E4200 to stop broadcasting wireless / lock up on the wireless side.
    I stopped using the Rosewill utlity and the issue has not happened again in over a week (I reproduced the issue by reenabling  the utlity at one point and within two days I experienced the same problem again).
    It also did not happen the first few weeks when I was not using the Rosewill utlity and had occurred another time when I used it right after getting the router (i.e. during the 2 periods of time during which the utility was disabled I had zero issues and the two times I turned the utility back on, the problem occurred again.
    (I only liked the Rosewill utility for it's advanced view of wireless networks in my area, including their exact signal strength, channel etc. I think SSIDer, as an alternative, provides this anyway).
    That is just one example.
    I am not saying the E4200 does not have flaws (I believe there are some documented DHCP issues that some have experienced etc.).
    I am only saying that with my setup and the features I use, my E4200 has been rock solid.

  • On the subject of dropped connections..

    I have a MBpro 15" CD. I also have a Netgear WGT624 and two WG602v3 (access Points).
    I use the 602's to bridge a connection to my living room which has almost no signal when connecting with the WGT624, due to distance issues. Furthermore, I needed a signal boost for my TIVO's USB Netgear wirless adaptor.
    Here is what I have noticed:
    When connected to the WGT624 I never drop a signal even when I have almost no signal left due to distance from router. However, when connecting to my WG602, the MB drops the signal every 10 min or so, even if i have full signal. My TIVO which is connected exclusively to the same WG602 does not experience dropped signal issues.
    I had read about the sudden dropped connections from other MBpro users but I never experienced one untill recently because I almost never connected to the internet using my WG602.
    From what I understand there is no solution for the sudden dropped connection. Changing routers will most probably solve your dropped signal issues. I think it's rather sad that one has to resort to that, but hey, if apple wont solve the problem, you have to....
    MB Pro 15" CD   Mac OS X (10.4.8)  

    Or there is Thunderbird, another free e-mail client which works very well.
    https://www.mozilla.org/en-GB/thunderbird/
    There are some useful help pages here, for BT Broadband customers only, on my personal website.
    BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

  • RV110W drops PPTP connections from a Windows client (MS CHAP v2 and MPPE)

    This might be a tough problem to diagnose. I am trying to setup an RV100W for an office gateway with VPN access using PPTP. The office is located in another state, so I'm trying to do a "dry run" from home by setting up the RV110W on the local network. That is, my home network is 192.168.0.0 and I have assigned the RV110W a static IP address of 192.168.0.120 on its WAN side and a DHCP NAT internal network of 192.168.1.0. Its LAN IP is 192.168.1.2 (because of legacy limitations, the 192.168.1.1 address will be reserved for another host on the actual office network) and I set up the PPTP server on 192.168.1.3 and clients in the 192.168.1.20 to 24 range. I have enabled MPPE encryption and NetBIOS over VPN (rather important to have).
    At first, I couldn't login at all. I had an underscore (_) in the user names (of which I have setup all five) and after I changed that, I was able to connect from a Windows 7 x64 host on the home LAN (192.168.0.132). I don't know if that was the problem as I got disconnected and reconnecting was a hit-or-miss - sometimes it would work, sometimes - it wouldn't. Below is the log from the session, showing the reasons for the disconnection. When I try to connect and it gets rejected, otherwise, the reason is the same: protocol not available.
    But, first - here's the kicker. I had the exact same experience earlier with a DD-WRT router. I thought the problem lied with the amateurish firmware and that's why I decided to get the Cisco, but it seems like this might not be the problem, after all. Here is that discussion for full details: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=149951&highlight= (to see all of the attached images and logs, you'll need an account). Briefly, with the same setup, I can establish a stable VPN connection from four Windows XP clients and one Windows 7 client, but I get the problems with two other Windows 7 clients. The Win7 clients that give me trouble can connect just fine to other PPTP VPN servers (with the built-in Microsoft PPTP client) and all three Win7 machines are clones of each other (only the hardware is different). No software firewalls, anti-virus/malware, user-permission limitations (e.g., UAC), or anything that could hamper the connections, are present on either machine.
    I don't see how the fact that the RV110W is on a LAN and not exposed to the Internet on its WAN side could cause any trouble, but even then - why some clients work fine and others - not? I would appreciate any help with this issue.
    Kamen
    This is the log from the session, showing the connection of the VPN client and then, not two minutes later, the disconnection.
    2012-02-22 21:44:40 RV110W daemon.info pptpd[4582]: CTRL: Client 192.168.0.132 control connection started
    2012-02-22 21:44:40 RV110W daemon.info pptpd[4582]: CTRL: Starting call (launching pppd, opening GRE)
    2012-02-22 21:44:40 RV110W daemon.notice pppd[4583]: pppd 2.4.5 started by (unknown), uid 0
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: using channel 2
    2012-02-22 21:44:40 RV110W daemon.info pppd[4583]: Using interface ppp0
    2012-02-22 21:44:40 RV110W daemon.notice pppd[4583]: Connect: ppp0 <--> /dev/pts/0
    2012-02-22 21:44:40 RV110W daemon.warning pppd[4583]: Warning - secret file /tmp/ppp/pap-secrets has world and/or group access
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [LCP ConfReq id=0x1 <auth chap MS-v2> <magic 0x4269dad6>]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [LCP ConfReq id=0x0 <mru 1400> <magic 0x5eec49d5> <pcomp> <accomp> <callback CBCP>]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [LCP ConfRej id=0x0 <pcomp> <accomp> <callback CBCP>]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [LCP ConfAck id=0x1 <auth chap MS-v2> <magic 0x4269dad6>]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [LCP ConfReq id=0x1 <mru 1400> <magic 0x5eec49d5>]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [LCP ConfAck id=0x1 <mru 1400> <magic 0x5eec49d5>]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [LCP EchoReq id=0x0 magic=0x4269dad6]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [CHAP Challenge id=0xfb <454ee20916a665999fdaa66778e1c4c5>, name = \"RV110W\"]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [LCP Ident id=0x2 magic=0x5eec49d5 \"MSRASV5.20\"]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [LCP Ident id=0x3 magic=0x5eec49d5 \"MSRAS-0-SOFTWAREONE64\"]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [LCP Ident id=0x4 magic=0x5eec49d5 \"H\\37777777772\\37777777612\\37777777633F\\177\\37777777752J\\37777777640[\\377777776451\\37777777610\\\\Ob\"]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [LCP EchoRep id=0x0 magic=0x5eec49d5]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [CHAP Response id=0xfb <2aeb8dac876cbec7c23036952cfc270c00000000000000006f4cafa17228047ac82f26e47ae69eda8fe8650d5866e44b00>, name = \"sakor001\"]
    2012-02-22 21:44:40 RV110W daemon.warning pppd[4583]: Warning - secret file /tmp/ppp/chap-secrets has world and/or group access
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [CHAP Success id=0xfb \"S=ACBA0BE9B8A98DDB757B234A1C69E9508DE169DE M=Access granted\"]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: Script /tmp/ppp/auth-up started (pid 4587)
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [CCP ConfReq id=0x1 <mppe +H -M +S +L -D -C>]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: Script /tmp/ppp/auth-up finished (pid 4587), status = 0x16
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [CCP ConfReq id=0x5 <mppe +H -M +S -L -D -C>]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [CCP ConfAck id=0x5 <mppe +H -M +S -L -D -C>]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [IPCP ConfReq id=0x6 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-wins 0.0.0.0> <ms-dns2 0.0.0.0> <ms-wins 0.0.0.0>]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [IPCP TermAck id=0x6]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [CCP ConfNak id=0x1 <mppe +H -M +S -L -D -C>]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [CCP ConfReq id=0x2 <mppe +H -M +S -L -D -C>]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [CCP ConfAck id=0x2 <mppe +H -M +S -L -D -C>]
    2012-02-22 21:44:40 RV110W daemon.notice pppd[4583]: MPPE 128-bit stateless compression enabled
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [IPCP ConfReq id=0x1 <addr 192.168.1.3>]
    2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [IPCP ConfAck id=0x1 <addr 192.168.1.3>]
    2012-02-22 21:44:42 RV110W daemon.debug pppd[4583]: rcvd [IPCP ConfReq id=0x7 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-wins 0.0.0.0> <ms-dns2 0.0.0.0> <ms-wins 0.0.0.0>]
    2012-02-22 21:44:42 RV110W daemon.debug pppd[4583]: sent [IPCP ConfRej id=0x7 <ms-wins 0.0.0.0> <ms-wins 0.0.0.0>]
    2012-02-22 21:44:42 RV110W daemon.debug pppd[4583]: rcvd [IPCP ConfReq id=0x8 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>]
    2012-02-22 21:44:42 RV110W daemon.debug pppd[4583]: sent [IPCP ConfNak id=0x8 <addr 192.168.1.20> <ms-dns1 216.165.129.157> <ms-dns2 216.170.153.146>]
    2012-02-22 21:44:42 RV110W daemon.debug pppd[4583]: rcvd [IPCP ConfReq id=0x9 <addr 192.168.1.20> <ms-dns1 216.165.129.157> <ms-dns2 216.170.153.146>]
    2012-02-22 21:44:42 RV110W daemon.debug pppd[4583]: sent [IPCP ConfAck id=0x9 <addr 192.168.1.20> <ms-dns1 216.165.129.157> <ms-dns2 216.170.153.146>]
    2012-02-22 21:44:42 RV110W daemon.notice pppd[4583]: local  IP address 192.168.1.3
    2012-02-22 21:44:42 RV110W daemon.notice pppd[4583]: remote IP address 192.168.1.20
    2012-02-22 21:44:42 RV110W daemon.debug pppd[4583]: Script /tmp/ppp/ip-up started (pid 4661)
    2012-02-22 21:44:42 RV110W daemon.debug pppd[4583]: Script /tmp/ppp/ip-up finished (pid 4661), status = 0x0
    2012-02-22 21:44:42 RV110W user.debug syslog: Nbsrelay start (pid= 4678)
    2012-02-22 21:46:10 RV110W daemon.notice pppd[4583]: Modem hangup
    2012-02-22 21:46:10 RV110W daemon.debug pppd[4583]: Script /tmp/ppp/auth-down started (pid 4858)
    2012-02-22 21:46:10 RV110W daemon.info pppd[4583]: Connect time 1.5 minutes.
    2012-02-22 21:46:10 RV110W daemon.info pppd[4583]: Sent 10404 bytes, received 17264 bytes.
    2012-02-22 21:46:10 RV110W daemon.debug pppd[4583]: Script /tmp/ppp/ip-down started (pid 4861)
    2012-02-22 21:46:10 RV110W daemon.err pppd[4583]: MPPE disabled
    2012-02-22 21:46:10 RV110W daemon.debug pppd[4583]: sent [LCP TermReq id=0x2 \"MPPE disabled\"]
    2012-02-22 21:46:10 RV110W daemon.notice pppd[4583]: Connection terminated.
    2012-02-22 21:46:10 RV110W daemon.debug pppd[4583]: Script /tmp/ppp/auth-down finished (pid 4858), status = 0x16
    2012-02-22 21:46:10 RV110W daemon.debug pppd[4583]: Waiting for 1 child processes...
    2012-02-22 21:46:10 RV110W daemon.debug pppd[4583]:   script /tmp/ppp/ip-down, pid 4861
    2012-02-22 21:46:10 RV110W daemon.debug pppd[4583]: Script /tmp/ppp/ip-down finished (pid 4861), status = 0x0
    2012-02-22 21:46:10 RV110W daemon.info pppd[4583]: Exit.
    2012-02-22 21:46:10 RV110W daemon.err pptpd[4582]: GRE: read(fd=11,buffer=449be4,len=8260) from network failed: status = -1 error = Protocol not available
    2012-02-22 21:46:10 RV110W daemon.err pptpd[4582]: CTRL: GRE read or PTY write failed (gre,pty)=(11,10)
    2012-02-22 21:46:10 RV110W daemon.debug pptpd[4582]: CTRL: Reaping child PPP[4583]
    2012-02-22 21:46:10 RV110W daemon.info pptpd[4582]: CTRL: Client 192.168.0.132 control connection finished

    Update: things are getting even weirder. In short - it seems to be working now (on the next day) without anything changing. First thing I did was just try another desperate tweak - I disabled the LCP extensions on the Windows client, which I've done before. It connected and stayed that way. Then, I reverted that setting back to exactly how it was before and connected again - no problems: it stayed connected for an hour (before I disconnected so I can connect to the real VPN), I could access a test-PC on the private network (a single machine just for the test) and do different tasks (resolve host names, browse UNC paths, copy files, Remote Desktop to it, etc.)
    I hate it when things happen, for which there is no explanation. I couldn't be confident sending this to the main office to replace the existing router (hardware) and VPN server (implemented in software on a Windows 2003 server). Any thoughts?
    Kamen
    P.S. I'm attaching the logs from the successful session in case someone wants to compare them, but they seems quite identical (some different ConfAck / ConfNak  sequences, but that doesn't seem to make much difference).
    2012-02-23 10:01:26 RV110W daemon.info pptpd[944]: CTRL: Client 192.168.0.132 control connection started
    2012-02-23 10:01:26 RV110W daemon.info pptpd[944]: CTRL: Starting call (launching pppd, opening GRE)
    2012-02-23 10:01:26 RV110W daemon.notice pppd[946]: pppd 2.4.5 started by (unknown), uid 0
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: using channel 5
    2012-02-23 10:01:26 RV110W daemon.info pppd[946]: Using interface ppp0
    2012-02-23 10:01:26 RV110W daemon.notice pppd[946]: Connect: ppp0 <--> /dev/pts/0
    2012-02-23 10:01:26 RV110W daemon.warning pppd[946]: Warning - secret file /tmp/ppp/pap-secrets has world and/or group access
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [LCP ConfReq id=0x1 ]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [LCP ConfReq id=0x0 ]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [LCP ConfRej id=0x0 ]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [LCP ConfAck id=0x1 ]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [LCP ConfReq id=0x1 ]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [LCP ConfAck id=0x1 ]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [LCP EchoReq id=0x0 magic=0x11372b0b]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [CHAP Challenge id=0x66 <74f93b7b6de315aaaac930f984c219e4>, name = \"RV110W\"]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [LCP Ident id=0x2 magic=0x67c80cba \"MSRASV5.20\"]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [LCP Ident id=0x3 magic=0x67c80cba \"MSRAS-0-SOFTWAREONE64\"]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [LCP Ident id=0x4 magic=0x67c80cba \"
    \\37777777675\\027\\37777777665\\004\\37777777635\\37777777677@H\\37777777633~\\37777777775\\021\\tFQ(\
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [LCP EchoRep id=0x0 magic=0x67c80cba]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [CHAP Response id=0x66 <2f0330cb61ba1c8e29324410e0df24d3000000000000000025d1ef07d4cd82beaa93fe36ccc1e863b2652087eb02c39400>, name = \"sakor001\"]
    2012-02-23 10:01:26 RV110W daemon.warning pppd[946]: Warning - secret file /tmp/ppp/chap-secrets has world and/or group access
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [CHAP Success id=0x66 \"S=9A5FB4C8B7C633FD6DEB868E150D0511BD93E0B4 M=Access granted\"]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: Script /tmp/ppp/auth-up started (pid 949)
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [CCP ConfReq id=0x1 ]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: Script /tmp/ppp/auth-up finished (pid 949), status = 0x16
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [CCP ConfReq id=0x5 ]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [CCP ConfNak id=0x5 ]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [IPCP ConfReq id=0x6 ]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [IPCP TermAck id=0x6]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [CCP ConfNak id=0x1 ]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [CCP ConfReq id=0x2 ]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [CCP ConfReq id=0x7 ]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [CCP ConfAck id=0x7 ]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [CCP ConfAck id=0x2 ]
    2012-02-23 10:01:26 RV110W daemon.notice pppd[946]: MPPE 128-bit stateless compression enabled
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [IPCP ConfReq id=0x1 ]
    2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [IPCP ConfAck id=0x1 ]
    2012-02-23 10:01:28 RV110W daemon.debug pppd[946]: rcvd [IPCP ConfReq id=0x8 ]
    2012-02-23 10:01:28 RV110W daemon.debug pppd[946]: sent [IPCP ConfRej id=0x8 ]
    2012-02-23 10:01:28 RV110W daemon.debug pppd[946]: rcvd [IPCP ConfReq id=0x9 ]
    2012-02-23 10:01:28 RV110W daemon.debug pppd[946]: sent [IPCP ConfNak id=0x9 ]
    2012-02-23 10:01:28 RV110W daemon.debug pppd[946]: rcvd [IPCP ConfReq id=0xa ]
    2012-02-23 10:01:28 RV110W daemon.debug pppd[946]: sent [IPCP ConfAck id=0xa ]
    2012-02-23 10:01:28 RV110W daemon.notice pppd[946]: local  IP address 192.168.1.3
    2012-02-23 10:01:28 RV110W daemon.notice pppd[946]: remote IP address 192.168.1.20
    2012-02-23 10:01:28 RV110W daemon.debug pppd[946]: Script /tmp/ppp/ip-up started (pid 1028)
    2012-02-23 10:01:28 RV110W daemon.debug pppd[946]: Script /tmp/ppp/ip-up finished (pid 1028), status = 0x0
    2012-02-23 10:01:28 RV110W user.debug syslog: Nbsrelay start (pid= 1040)
    2012-02-23 10:17:56 RV110W daemon.err pptpd[944]: GRE: Bad checksum from pppd.
    2012-02-23 10:31:51 RV110W daemon.info udhcpd[807]: received INFORM from 00:13:46:E6:D3:FA
    2012-02-23 10:48:20 RV110W daemon.info httpd[376]: Administrator session timeout.
    2012-02-23 10:48:27 RV110W daemon.info httpd[376]: Administrator logined from 192.168.0.132
    2012-02-23 10:52:50 RV110W daemon.info udhcpd[807]: received INFORM from 00:26:F2:B7:49:42
    2012-02-23 10:58:49 RV110W daemon.debug pppd[946]: rcvd [LCP TermReq id=0xb \"g\\37777777710\\014\\37777777672\\000<
    \\37777777715t\\000\\000\\000\\000\
    2012-02-23 10:58:49 RV110W daemon.info pppd[946]: LCP terminated by peer (gM-H^LM-:^@
    2012-02-23 10:58:49 RV110W daemon.debug pppd[946]: Script /tmp/ppp/auth-down started (pid 6011)
    2012-02-23 10:58:49 RV110W daemon.info pppd[946]: Connect time 57.4 minutes.
    2012-02-23 10:58:49 RV110W daemon.info pppd[946]: Sent 272072987 bytes, received 6264878 bytes.
    2012-02-23 10:58:49 RV110W daemon.debug pppd[946]: Script /tmp/ppp/ip-down started (pid 6015)
    2012-02-23 10:58:49 RV110W daemon.debug pppd[946]: sent [LCP TermAck id=0xb]
    2012-02-23 10:58:49 RV110W daemon.debug pppd[946]: Script /tmp/ppp/auth-down finished (pid 6011), status = 0x16
    2012-02-23 10:58:49 RV110W daemon.notice pppd[946]: Modem hangup
    2012-02-23 10:58:49 RV110W daemon.notice pppd[946]: Connection terminated.
    2012-02-23 10:58:49 RV110W daemon.debug pppd[946]: Waiting for 1 child processes...
    2012-02-23 10:58:49 RV110W daemon.debug pppd[946]:   script /tmp/ppp/ip-down, pid 6015
    2012-02-23 10:58:49 RV110W daemon.debug pppd[946]: Script /tmp/ppp/ip-down finished (pid 6015), status = 0x0
    2012-02-23 10:58:49 RV110W daemon.info pppd[946]: Exit.
    2012-02-23 10:58:49 RV110W daemon.debug pptpd[944]: CTRL: Reaping child PPP[946]
    2012-02-23 10:58:49 RV110W daemon.info pptpd[944]: CTRL: Client 192.168.0.132 control connection finished

  • New time capsule+new airport express=daily dropped connections

    I have a new 2 TB Time Capsule and a new Airport Express that I puchased to update my old set-up of an Airport Express and Airport Extreme.
    I have the TC set-up as the primary base station in the back of the house and the airport express set-up to extend the network in the front of the house. I was getting constant disconnects up front for the first several days so I finally exchanged the new AX for another one thinking maybe the first one was faulty. I reset the TC back to factory defaults for good measure and re-set up my network the same way with the new AX.
    Two days with no disconnects, thought it was fixed, and then it started again...no joy. Not as often as with the first AX, but still it happens 2-3 times a day and always up in the front of the house while we're on our MacBook Pro or MacBook Air. When this happens both the AX and the TC have green lights and full bars of connectivity show in the menu bar, but yet no internet access. The only way to reconnect is to restart the AX. I have noticed too, that when this happens, the Airport Utility does not show the TC at all...even though it's light is fully green and it should be there, it just shows the AX until I restart and then both show up again.
    I've tried changing the channel from automatic to a specific channel but this really doesn't change things much. Now I'm starting to wonder if something is awry with the TC. I've also noticed that it sometimes fails to back up because it can't find a connection to my iMac which is right next to it in the back of the house.
    So far this upgrade has been more of a downgrade. Any help would be greatly appreciated!

    Just an update and still seeking some advice for this situation...anybody?
    I tried re-setting both TC and AX to factory settings and re-configuring. Still get at least 3-4 dropped connections up front on a daily basis; however, TC has been connecting successfully and backing up my iMac, so at least that seems to be ok.
    Still the same situation with the TC not showing up in Airport Utility every time the network connection drops happen...just the AX is seen until I finally have to restart the AX and then both can be viewed in Airport Utility and the internet connection is restored. Sometimes I can restore connection by simply toggling my airport access on and off in the menu bar of my MacBook Pro, but more often then not, I have to restart the AX itself to get back online.
    Is it possible that this could be an issue with the TC? Somehow it might be dropping the connection to the AX? I can still exchange it for another if this may be the case. I'm already on my second AX thinking that the Express was the problem initially.
    So far, nothing seems to help the situation. About the only thing that I haven't done is configure the AX to just join the network rather than extend it...but that would be defeating the purpose of why I bought it in the first place (to stream iTunes and extend network).
    I never had issues with my old set-up, but then I had it configured as a WDS because I didn't have the option to "extend" the network as it was an older AX and Airport Express.

  • 10.7.3 MBP Wifi Problem - Endless Timeouts & Dropped connections

    I've been reading around here a bit already and so I know many other people are having Wifi issues with Lion, but given that there are so many discussions and so many pages of talk, it's hard to go through it all, and using the search I haven't found anything that's quite similar to what I'm experiencing, so I'm starting a new topic...
    Basically, I've got a late 2006 MacBook Pro, installed 10.7.1 (form 10.6.8) on in back in Aug 2011 and everything seemed to be fine. I updated to 10.7.2 sometime in Jan and still didn't notice any issues, but wasn't using Wifi at all at the time.
    Then in Feb I moved and started using wifi (with a Cisco N router), and noticed that often, the system would not automatically reconnect to the network after waking up from sleep. Just selecting the network manually worked on the first try every time though, so it wasn't so bad.
    At the end of April, I finally got around to installing the 10.7.3 update. I read it was supposed to fix wifi issues and so was looking forward to it. It installed fine and didn't seem to cause any problems...
    2 days later I moved again (to India), and all **** broke loose... Now, I can rarely connect to wifi (a Beetel G router, configed with WPA). Around 25% of the time, the network won't show up in the list (despite being a clear 5ft from the base station), and when it does show up, 95% of the time I get a "connection timeout" error - often immeadiately, but sometimes it takes about 10sec to respond. On the same network, 2 Win 7 Dells and an iPad 1 all work flawlessly - it's not the router...
    One the occasions that I am able to connect, it usually works fine, but if I put the computer to sleep and wake up again, there's no guarentee that the connection will work again - it's back to the lottery. And sometimes even when it's connected, the wifi stays (according to the menu indicator) but the internet connection disappears (to the point I can't even ping the router - 100% packet loss, let alone any internet server)
    I've tried zapping everything I can think of (PRAM, SMC), repairing permissions, clearing the remembered networks from the System Prefs, deleting old Locations and creating new ones etc. I have a clean install of 10.7.1 that I booted off of, but it still had the same issues!
    Here's the Wifi output from System Profiler (trying to use "Home Network"):
    Software Versions:
      CoreWLAN:          2.1.2 (212.1)
      CoreWLANKit:          1.0.2 (102.2)
      Menu Extra:          7.0.2 (702.1)
      configd plug-in:          7.1.2 (712.1)
      System Profiler:          7.0 (700.3)
      IO80211 Family:          4.1.2 (412.2)
      WiFi Diagnostics:          1.0.1 (101.1)
      AirPort Utility:          6.0 (600.92)
      Interfaces:
    en1:
      Card Type:          AirPort Extreme
      Firmware Version:          Atheros 5416: 2.1.14.9
      MAC Address:          00:XX:XX:XX:XX
      Locale:          FCC
      Country Code:          IN
      Supported PHY Modes:          802.11 a/b/g/n
      Supported Channels:          1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165
      Status:          Not Associated
      Local Wi-Fi Networks:
    Home Network:
      PHY Mode:          802.11g
      BSSID:          80:a1:d7:4a:d0:02
      Channel:          1
      Network Type:          Infrastructure
      Security:          WPA Personal
      Signal / Noise:          -77 dBm / -96 dBm
    MGMNT:
      PHY Mode:          802.11g
      BSSID:          80:a1:d7:4a:d0:03
      Channel:          1
      Network Type:          Infrastructure
      Security:          WEP
      Signal / Noise:          -77 dBm / -96 dBm
    RC:
      PHY Mode:          802.11g
      BSSID:          00:1e:40:57:67:61
      Channel:          6
      Network Type:          Infrastructure
      Security:          WPA Personal
      Signal / Noise:          -97 dBm / -96 dBm
    Vivek:
      PHY Mode:          802.11g
      BSSID:          00:24:b2:94:ea:06
      Channel:          11
      Network Type:          Infrastructure
      Security:          WEP
      Signal / Noise:          -94 dBm / -96 dBm
    nischai:
      PHY Mode:          802.11n
      BSSID:          58:6d:8f:c3:ea:2a
      Channel:          6
      Network Type:          Infrastructure
      Security:          WPA2 Personal
      Signal / Noise:          -90 dBm / -96 dBm
    noor:
      PHY Mode:          802.11g
      BSSID:          00:24:b2:7e:26:72
      Channel:          11
      Network Type:          Infrastructure
      Security:          WPA Personal
      Signal / Noise:          -90 dBm / -96 dBm
    One thread here I read had someone suggesting to run the Airport debugger in Terminal and posting the output - here's the results:
    Sat May  5 09:52:00.823 <kernel> IO80211ScanManager::startScan: Broadcast scan request received from pid 622 ().
    Sat May  5 09:52:00.824 <kernel> IO80211ScanManager::startScan: Initiating scan.
    Sat May  5 09:52:00.824 <kernel> __ieee80211_newstate: INIT -> SCAN (arg 0xffffffff)
    Sat May  5 09:52:00.824 <kernel> ieee80211_check_scan: active scan, duration 24000, desired mode auto, append, nopick
    Sat May  5 09:52:00.824 <kernel> ieee80211_start_scan: active scan, duration 24000, desired mode auto, append, nopick
    Sat May  5 09:52:00.824 <kernel> scan_next: chan   1g ->   1g [active, dwell min 8 max 8]
    Sat May  5 09:52:00.865 <kernel> [80:a1:d7:4a:d0:02] new beacon on chan 1 (bss chan 1) "Home Network"
    Sat May  5 09:52:00.865 <kernel> [80:a1:d7:4a:d0:02] caps 0x411 bintval 100 erp 0x4 
    Sat May  5 09:52:00.873 <kernel> [80:a1:d7:4a:d0:03] new beacon on chan 1 (bss chan 1) "MGMNT"
    Sat May  5 09:52:00.873 <kernel> [80:a1:d7:4a:d0:03] caps 0x411 bintval 100 erp 0x4 
    Sat May  5 09:52:00.909 <kernel> scan_next: chan   1g ->   6g [active, dwell min 8 max 8]
    Sat May  5 09:52:00.917 <kernel> [58:6d:8f:c3:ea:2a] new probe_resp on chan 6 (bss chan 6) "nischai"
    Sat May  5 09:52:00.919 <kernel> [58:6d:8f:c3:ea:2a] caps 0x411 bintval 100 erp 0x4 
    Sat May  5 09:52:00.920 <kernel> [58:6d:8f:c3:ea:2a] new probe_resp on chan 6 (bss chan 6) "nischai"
    Sat May  5 09:52:00.920 <kernel> [58:6d:8f:c3:ea:2a] caps 0x411 bintval 100 erp 0x4 
    Sat May  5 09:52:00.928 <kernel> [58:6d:8f:c3:ea:2a] new probe_resp on chan 6 (bss chan 6) "nischai"
    Sat May  5 09:52:00.928 <kernel> [58:6d:8f:c3:ea:2a] caps 0x411 bintval 100 erp 0x4 
    Sat May  5 09:52:00.992 <kernel> scan_next: chan   6g ->  11g [active, dwell min 8 max 8]
    Sat May  5 09:52:01.47  <kernel> [00:24:b2:7e:26:72] new beacon on chan 11 (bss chan 11) "noor"
    Sat May  5 09:52:01.47  <kernel> [00:24:b2:7e:26:72] caps 0x411 bintval 100 erp 0x0 
    Sat May  5 09:52:01.75  <kernel> scan_next: chan  11g ->   7g [active, dwell min 8 max 8]
    Sat May  5 09:52:01.158 <kernel> scan_next: chan   7g ->  13g [active, dwell min 8 max 8]
    Sat May  5 09:52:01.241 <kernel> scan_next: chan  13g ->  52a [passive, dwell min 8 max 8]
    Sat May  5 09:52:01.327 <kernel> scan_next: chan  52a ->  56a [passive, dwell min 8 max 8]
    Sat May  5 09:52:01.409 <kernel> scan_next: chan  56a ->  60a [passive, dwell min 8 max 8]
    Sat May  5 09:52:01.492 <kernel> scan_next: chan  60a ->  64a [passive, dwell min 8 max 8]
    Sat May  5 09:52:01.575 <kernel> scan_next: chan  64a ->  36a [active, dwell min 8 max 8]
    Sat May  5 09:52:01.657 <kernel> scan_next: chan  36a ->  40a [active, dwell min 8 max 8]
    Sat May  5 09:52:01.741 <kernel> scan_next: chan  40a ->  44a [active, dwell min 8 max 8]
    Sat May  5 09:52:01.823 <kernel> scan_next: chan  44a ->  48a [active, dwell min 8 max 8]
    Sat May  5 09:52:01.906 <kernel> scan_next: chan  48a ->   2g [active, dwell min 8 max 8]
    Sat May  5 09:52:01.920 <kernel> [04:4f:aa:b4:dc:f9] new beacon on chan 2 (bss chan 2) ""
    Sat May  5 09:52:01.920 <kernel> [04:4f:aa:b4:dc:f9] caps 0x431 bintval 100 erp 0x0 
    Sat May  5 09:52:01.992 <kernel> scan_next: chan   2g ->   3g [active, dwell min 8 max 8]
    Sat May  5 09:52:02.74  <kernel> scan_next: chan   3g ->   4g [active, dwell min 8 max 8]
    Sat May  5 09:52:02.157 <kernel> scan_next: chan   4g ->   5g [active, dwell min 8 max 8]
    Sat May  5 09:52:02.239 <kernel> scan_next: chan   5g ->   8g [active, dwell min 8 max 8]
    Sat May  5 09:52:02.321 <kernel> scan_next: chan   8g ->   9g [active, dwell min 8 max 8]
    Sat May  5 09:52:02.388 <kernel> [00:26:15:61:4c:87] new beacon on chan 9 (bss chan 9) "BSNL_AP"
    Sat May  5 09:52:02.388 <kernel> [00:26:15:61:4c:87] caps 0x431 bintval 100 erp 0x0  country info  49 4e 49 01 0d 14
    Sat May  5 09:52:02.403 <kernel> scan_next: chan   9g ->  10g [active, dwell min 8 max 8]
    Sat May  5 09:52:02.486 <kernel> scan_next: chan  10g ->  12g [active, dwell min 8 max 8]
    Sat May  5 09:52:02.569 <kernel> scan_next: chan  12g -> 149a [active, dwell min 8 max 8]
    Sat May  5 09:52:02.655 <kernel> scan_next: chan 149a -> 153a [active, dwell min 8 max 8]
    Sat May  5 09:52:02.738 <kernel> scan_next: chan 153a -> 157a [active, dwell min 8 max 8]
    Sat May  5 09:52:02.821 <kernel> scan_next: chan 157a -> 161a [active, dwell min 8 max 8]
    Sat May  5 09:52:02.903 <kernel> scan_next: chan 161a -> 165a [active, dwell min 8 max 8]
    Sat May  5 09:52:02.991 <kernel> scan_next: done, [ticks 32630, dwell min 8 scanend 56413]
    Sat May  5 09:52:02.993 <kernel> __ieee80211_newstate: SCAN -> INIT (arg 0xffffffff)
    Sat May  5 09:52:02.993 <kernel> ieee80211_init_node[1132] old_auth 5
    Sat May  5 09:52:02.994 <kernel> IO80211ScanManager::getScanResult: All scan results returned for pid 622.
    Sat May  5 09:52:05.765 <airportd[804]> _handleNewMessage: Received XPC message, event = ASSOC_EVENT, pid = 622
    Sat May  5 09:52:05.766 <airportd[804]> associate: INFO: airportd associate: network=<CWNetwork: 0x7f9fd8c11fc0> [ssid=Home Network, bssid=80:a1:d7:4a:d0:02, security=WPA Personal, rssi=-76, channel=<CWChannel: 0x7f9fd8c185b0> [channelNumber=1(2GHz), channelWidth={20MHz}], ibss=0], is8021X=0, remember=1
    Sat May  5 09:52:05.781 <airportd[804]> associate: INFO: Checking if admin authorization is required
    Sat May  5 09:52:05.802 <kernel> __ieee80211_newstate: INIT -> SCAN (arg 0x0)
    Sat May  5 09:52:05.802 <kernel> ieee80211_check_scan: active scan, duration 24000, desired mode auto, append
    Sat May  5 09:52:05.802 <kernel> ieee80211_check_scan: check scan cache
    Sat May  5 09:52:05.802 <kernel>  macaddr          bssid         chan  rssi rate flag  wep  essid
    Sat May  5 09:52:05.802 <kernel> 
    Sat May  5 09:52:05.802 <kernel> 
    Sat May  5 09:52:05.802 <kernel> 
    Sat May  5 09:52:05.802 <kernel> 
    Sat May  5 09:52:05.802 <kernel> 
    Sat May  5 09:52:05.802 <kernel> 
    Sat May  5 09:52:05.802 <kernel> 
    Sat May  5 09:52:05.802 <kernel> 
    Sat May  5 09:52:05.802 <kernel> 
    Sat May  5 09:52:05.802 <kernel> 
    Sat May  5 09:52:05.802 <kernel> 
    Sat May  5 09:52:05.802 <kernel> 
    Sat May  5 09:52:05.802 <kernel> 
    Sat May  5 09:52:05.802 <kernel> 
    Sat May  5 09:52:05.802 <kernel> 
    Sat May  5 09:52:05.802 <kernel> 
    Sat May  5 09:52:05.802 <kernel> 
    Sat May  5 09:52:05.802 <kernel> 
    Sat May  5 09:52:05.802 <kernel> 
    Sat May  5 09:52:05.807 <kernel> 
    Sat May  5 09:52:05.807 <kernel> ieee80211_init_node[1132] old_auth 5
    Sat May  5 09:52:05.807 <kernel> __ieee80211_newstate: SCAN -> JOIN (arg 0x0)
    Sat May  5 09:52:05.812 <kernel> __ieee80211_newstate: JOIN -> AUTH (arg 0xc0)
    Sat May  5 09:52:05.813 <kernel> ieee80211_cancel_scan: cancel active scan
    Sat May  5 09:52:05.813 <kernel> scan_next: done, [ticks 32912, dwell min 8 scanend 56413]
    Sat May  5 09:52:05.813 <kernel> parseWPAIE: groupCipherType = 3 pairwiseCipherType = 3 authSel = 2
    Sat May  5 09:52:05.813 <kernel> initWithInterfaceAndIE: _myMacAddress 00:17:f2:e6:81:a1
    Sat May  5 09:52:05.813 <kernel> setPMK: PMK SET!
    Sat May  5 09:52:05.815 <kernel> ieee80211_tx_timeout: state AUTH
    Sat May  5 09:52:05.815 <kernel> [80:a1:d7:4a:d0:02] ieee80211_scan_assoc_fail: reason 1
    Sat May  5 09:52:05.815 <kernel> [80:a1:d7:4a:d0:02] sta_assoc_fail: reason 1
    Sat May  5 09:52:05.815
    Sat May  5 09:52:05.815 <kernel> __ieee80211_newstate: AUTH -> SCAN (arg 0x1)
    Sat May  5 09:52:05.815 <kernel> [80:a1:d7:4a:d0:02] ieee80211_scan_assoc_fail: reason 1
    Sat May  5 09:52:05.816 <kernel> ieee80211_init_node[1132] old_auth 5
    Sat May  5 09:52:05.816 <kernel> ieee80211_check_scan: active scan, duration 24000, desired mode auto, append
    Sat May  5 09:52:05.816 <kernel> ieee80211_check_scan: check scan cache
    Sat May  5 09:52:05.816 <kernel>  macaddr          bssid         chan  rssi rate flag  wep  essid
    Sat May  5 09:52:05.816 <kernel> 
    Sat May  5 09:52:05.816 <kernel> 
    Sat May  5 09:52:05.816 <kernel> 
    Sat May  5 09:52:05.816 <kernel> 
    Sat May  5 09:52:05.816 <kernel> 
    Sat May  5 09:52:05.816 <kernel> 
    Sat May  5 09:52:05.816 <kernel> 
    Sat May  5 09:52:05.816 <kernel> 
    Sat May  5 09:52:05.816 <kernel> 
    Sat May  5 09:52:05.816 <kernel> 
    Sat May  5 09:52:05.816 <kernel> 
    Sat May  5 09:52:05.816 <kernel> 
    Sat May  5 09:52:05.816 <kernel> 
    Sat May  5 09:52:05.816 <kernel> 
    Sat May  5 09:52:05.816 <kernel> 
    Sat May  5 09:52:05.816 <kernel> 
    Sat May  5 09:52:05.816 <kernel> 
    Sat May  5 09:52:05.816 <kernel> 
    Sat May  5 09:52:05.816 <kernel> 
    Sat May  5 09:52:05.816 <kernel> ieee80211_start_scan: active scan, duration 24000, desired mode auto, append
    Sat May  5 09:52:05.816 <kernel> scan_next: chan   1g ->   1g [active, dwell min 8 max 8]
    Sat May  5 09:52:05.834 <kernel> ieee80211_cancel_scan: cancel active scan
    Sat May  5 09:52:05.834 <kernel> __ieee80211_newstate: SCAN -> INIT (arg 0xffffffff)
    Sat May  5 09:52:05.834 <kernel> ieee80211_init_node[1132] old_auth 5
    Sat May  5 09:52:05.835 <kernel> en1: Terminating supplicant.
    Sat May  5 09:52:05.835 <kernel> RSNSupplicant: Releasing authenticator for 00:00:00:00:00:00
    Sat May  5 09:52:05.835 <airportd[804]> associate: Apple80211Associate2() failed with error -3905
    Sat May  5 09:52:21.354 <kernel> IO80211ScanManager::cachePurge: clearEntries[0] Firing!
    Sat May  5 09:52:21.354 <kernel> IO80211ScanManager::cachePurge: Rescheduling in 14 seconds.
    Sat May  5 09:52:35.354 <kernel> IO80211ScanManager::cachePurge: clearEntries[0] Firing!
    Sat May  5 09:52:35.354 <kernel> IO80211ScanManager::cachePurge: NOT Rescheduling.
    I'm pretty savy with computers and have dealt with all kinds of stuff before, but this one is beyond me, and is really annoying! I konw my machine is old, but it was totally useable up until these Wifi issues, and now wifi is basically useless.
    From what I've read, it seems like its a driver issue with the Atheros card in my machine, but most people seem to be complaining about dropped connections (mine rarely drops) rather than timeout connection issues. I've also never had the "hardware not found" issue that many people have, so I think this is something different.
    Anyone out there have any advice? I'm getting close to losing it with wifi since the update!

    Sorry - to add:
    I don't think it's a question of WPA vs. WPA2, or even channel number - I have 2 identical routers here and neither work (both default to WPA Ch 11) but I changed one to WPA2, new SSID, various channels and still had the same problems.
    Another thing to note that should be irrelevant, but who knows: the Firewire controller on my machine died back in Fall 2010 - to the point where the system won't start-up unless I remove the IOFirewire***.kext from /System/Library/Extensions , and as soon as I do that, it works flawlessly (minus Firewire). It meant I had a **** of a time installing Lion becuase I can't boot off the Recovery Partition (which has the drivers baked into it), but by cloneing my HD, installing Lion onto the clone via a borrowed machine, removing the .kext's and cloning back, I got it on and everything seems to be fine otherwise... I posted about that problem before, but never got any answers. And it wasn't just me, my father has a late 2007 MBP and the same firewire issue happened to his within 5 days of mine (not a power spike - I think it was shortly after some system update if I remember correctly).

  • Poor performance and now dropping connection

    I am very underwhelmed by performance since switching to infinity FTTC last year. Download speed is very variable and I just cannot get an upload speed much better than 1.1 Mb/s.
    Now we have a regularly dropping connection. Last Saturday morning we had a thunderstorn with heavy downpour and phone line dropped completely - no dialtone and unsurprisingly no broadband. Did a line check from my mobile - all fine and no reported problems in the area. I phoned BT and got an Indian who just repeated what the website told me and said couldn't get an engineer for 4 days! Phone came back late the same afternoon and a little while later broadband came up but connection was up and down like a yo-yo. After 4 days of sunshine when the engineer turned up broadband had been up solid from 3 am and phone was fine. Engineer did more detailed tests which showed no problem and reckoned our problem must have been fixed, and that reason broadband had been dropping was because of computerised checks due to reported fault which would cause line to drop.
    For a few days all was fine, although performance still underwheliming, until we had another downpour yesterday morning. Phone line stayed up, although a little crackly, but once again broadband started dropping regularly. Since then it has gradually improved (no more rain).
    My suspicion is (and always has been) that with the heavy rain water is getting into a connection somewhere. How do I go about communicating it to BT support (I can't even find a web page or number for reporting broadband problems) this fact and actually getting someone to look into it properly? I rejected the "fault reported fixed" on the tracking your fault web page but so far nothing.
    I am distinctly unimpressed with BT support and unless this gets fixed soon I am seriously thinking of switching to fibre to the home with Virgin (despite hating Branson) especially as the move from Yahoo mail to BT mail has not been smooth and the BT webmail is full of bugs (which again I cannot find any way of reporting).

    Thanks. I tried that. Broadband up and down regularly until the day the engineer came. Day before had intermittent heavy crackling on the line and calls dropping. Day he came all is fine and of course his diagnostics checks come back all clear. Apparently, or so he told me, they are not allowed to work on our line unless the checks show a fault...which they didn't.
    I've just had 24 hours of our broadband working but just now it's started dropping regularly again.
    I am getting very frustrated/annoyed. What do I do now? How do they expect to solve the problem if it isn't constant and they can't get an engineer to look at it within 3 or 4 days? Do I just keep on calling our an engineer until by chance it happens to hit a problem while they're on site? Not good for customer satisfaction and surely it must cost them to keep sending out an engineer!

  • AT&T U-verse dropping connections suddenly

    Hi all.
    Since upgrading to Yosemite, there has been a degrading of my internet reliability with AT&T U-verse, and its been getting worse and worse.  I now drop connections every HOUR.  Speed and WiFi strength are great when its working, but it will spontaneously stop working, and if i do a series of diagnostics, quitting safari, turning wifi off and on, etc., I can get back online after a few minutes.  BUT WHAT THE HECK IS HAPPENING?  At this point I've mucked around with just about every network setting so I no longer even know what they should be.  AT&T is fairly useless regarding tech support for Macs, so hopefully someone here knows the current UVerse setup and can give me some advice.  Here's where I stand:
    - I have a 2009 Mac Pro, running latest Yosemite.
    - Router is AT&T Motorola NVG589, connecting to U-verse service (not gigabit, just regular)
    - When internet service drops, it appears that the WiFi continues to be connected well, at least for a while.  The NVG589 status page still shows my machine connected, and the WiFi signal strength in the menu bar remains full strength, but Diagnostics show failure to connect to ISP and internet.  Other Devices, like my phone or other laptops, continue to connect fine, so the broadband is fine, so maybe the WiFi is only appearing to work or something else is going on.  At some point, the WiFi also stops responding until I do a bunch of restarting stuff.
    - I have already trashed the various preference files and created fresh new locations, but to no avail.  It all works fine for a while then goes spotty again.
    - I have my network prefs set to "Link-local only" which had worked fine before.
    - I set the DNS servers to 8.8.8.8 and 8.8.4.4
    I don't really know much about the various pros and cons of different settings, but apparently you can get the NVG589 to assign a static IP address (or semi-static or something like that) but is that BETTER?   would that end the dropouts?
    Any other ideas?

    Hello Javier Bonafont,
    Welcome to the Apple Support Communities!
    I understand that it can be very frustrating when you are having multiple Wi-Fi drops in signal at home. There are a couple of different troubleshooting steps that I would recommend in this situation. Please refer to the attached article for information and steps to help you troubleshoot this situation.
    Wi-Fi: How to troubleshoot Wi-Fi connectivity - Apple Support
    Symptom: The network connection drops unexpectedly
    Your Mac may not not stay connected to your Wi-Fi network reliably.
    Your Mac may stop accessing the Internet during use.
    Solution
    Use these steps if your computer disconnects from its Wi-Fi network unexpectedly.
    Check your range to the Wi-Fi router and reduce the effect of interference.If your computer is too far from your Wi-Fi router or your environment has too much Wi-Fi interference, then your computer may not detect the Wi-Fi network properly. The easiest way to check for range limits with your Wi-Fi network is to move your computer or your Wi-Fi router closer together and make sure that there are no obstructions (such as walls, cabinets, and so forth) between the router and your computer.See Potential sources of wireless interference for more information about interference and solutions.
    Try connecting to a different Wi-Fi network. If your computer works fine when connected to a different Wi-Fi network, then the issue may be related to your network router or ISP. In that case, contact the manufacturer of your router or your ISP.
    Best regards,
    Joe

  • Error While creating new database connection from HFM workspace

    Hi,
    We have recently installed HFM and was trying to create database connection from database connection manager in HFM workspace.
    I am getting below error:
    "Error connecting to database connection : no HssJNIDriver950 in java.library.path" initially and later
    "Error connecting to database connection : com/hyperion/ap/adm/HssConn".
    Any information in this direction would helpful.
    Thanks,
    Bhargav
    Edited by: bhargavr on Jan 24, 2011 6:55 PM

    Hi bhargavr,
    We came accross the same issue. Try the following solution below for this 'KNOWN ISSUE' and let me know how you get on. Drop me a note if you have any questions regarding this post.
    Error: *"Error connecting to database connection: com/hyperion/ap/adm/HssConn" While Creating a Financial Management Database Connection* [ID 1102697.1]
    Modified 04-JAN-2011 Type PROBLEM Status PUBLISHED
    Applies to:
    Hyperion BI+ - Version: 11.1.2.0.00 and later [Release: 11.1 and later ]
    Microsoft Windows x64 (64-bit)
    Symptoms:
    You are running the Financial Reporting Web Server on a 64-bit server.
    When you try to create a new Financial Management (HFM) database connection using the Database Connection Manager in Workspace you receive the following message:
    “Error connecting to database connection <connection_name>: com/hyperion/ap/adm/HssConn”
    You can create a database connection in Financial Reporting Studio. When you refresh a report with a Financial Management database connection, you receive one of the following messages:
    “1001: Error connecting to database connection <DATABASE_CONNECTION_NAME>: com/hyperion/ap/adm/HssConn”
    or
    “1001: Error connecting to database connection <DATABASE_CONNECTION_NAME>: no HssJNIDriver950 in java.library.path”
    Cause:
    The issue is documented in unpublished bug 9537050, and in Known Issues in the 11.1.2 Reporting and Analysis Readme. Cross-reference unpublished bug 9707353.
    Solution:
    In the Windows registry, take the following steps:
    Navigate to HKEY_LOCAL_MACHINE\SOFTWARE\HyperionSolutions\FinancialReporting0\HyS9FRReports.
    For each of the following entries, prefix the contents with text in the blue box: Env2, JVMOption13, and JVMOption17 (note that the JVMOption numbers might be slightly different in your environment).
    C:\Oracle\Middleware\EPMSystem11R1\common\ADM\11.1.2.0\bin-64
    If your EPM_ORACLE_HOME is not located at C:\Oracle\Middleware\EPMSystem11R1, replace that location with your location.
    Restart the server.
    G'Luck,
    -David

  • Issue with AFP server dropping connections on 10.8.5 server 2.2.2

    We are having issues with users getting dropped from their AFP server shares.
    These issues did not start happening until we upgraded to 10.8.5 and server 2.2.2
    the first symptoms were an occasional user would lose his / her active connection while copying files. They were unable to disconnect from the network shares without physically disconnecting the LAN or disabling the network on their system. Once the connection was removed they could reconnect to the network and establish their AFP shares again.
    However this his escalated to every user losing connections to their AFP shares at the same time.
    The server has no AFP error in the AFP error log however we are getting diskutil crash reports at around the same time. (See Below)
    The server has
    smalltree 1x6 8254 with latest drivers supporting a LACP bonded 6 pair connecting to an edgecore (LACP configured)switch.
    small tree 10Gb card directly connected to an edit station.
    onboard ethernet connected to switch in support of DHCP & DNS. (previous version of server would not see the bonded pair)
    Two Accusys A12S2's
    (we did not have this dropping connection issue before the upgrade to server 2.2.2 and OSX 10.8.5)
    Users connected to any network connection to the server appear to be affected when the AFP shares are disconnected. Direcet connect, onboard ethernet port and Bonded pair connections)
    diskutil verifies all shared drives appear to be ok. (All Green)
    SYSTEM LOG
    Feb 23 11:15:44 doghouse.local diskutil[1067]: -[__NSCFConstantString getBytes:length:]: unrecognized selector sent to instance 0x7fff7628bbe8
    Feb 23 11:15:44 doghouse.local diskutil[1067]: *** Terminating app due to uncaught exception 'NSInvalidArgumentException', reason: '-[__NSCFConstantString getBytes:length:]: unrecognized selector sent to instance 0x7fff7628bbe8'
              *** First throw call stack:
                        0   CoreFoundation                      0x00007fff91b2bb06 __exceptionPreprocess + 198
                        1   libobjc.A.dylib                     0x00007fff901403f0 objc_exception_throw + 43
                        2   CoreFoundation                      0x00007fff91bc240a -[NSObject(NSObject) doesNotRecognizeSelector:] + 186
                        3   CoreFoundation                      0x00007fff91b1a02e ___forwarding___ + 414
                        4   CoreFoundation                      0x00007fff91b19e18 _CF_forwarding_prep_0 + 232
                        5   diskutil                            0x000000010c1eb550 diskutil + 83280
                        6   diskutil                            0x000000010c1ea0af diskutil + 77999
                        7   diskutil                            0x000000010c1e7abe diskutil + 68286
                        8   diskutil                            0x000000010c1dd0ef diskutil + 24815
                        9   diskutil                            0x000000010c1e5161 diskutil + 57697
                        10  Foundation                          0x00007fff8d29dd05 __NSFireDelayedPerform + 358
                        11  CoreFoundation                      0x00007fff91ae8804 __CFRUNLOOP_IS_CALLING_OUT_TO_A_TIMER_CALLBACK_FUNCTION__ + 20
                        12  CoreFoundation                      0x00007fff91ae831d __CFRunLoopDoTimer + 557
                        13  CoreFoundation                      0x00007fff91acdad9 __CFRunLoopRun + 1529
                        14  CoreFoundation                      0x00007fff91acd0e2 CFRunLoopRunSpecific + 290
                        15  Foundation                          0x00007fff8d2c57ee -[NSRunLoop(NSRunLoop) runMode:beforeDate:] + 268
                        16  Foundation                          0x00007fff8d25e1aa -[NSRunLoop(NSRunLoop) run] + 74
                        17  diskutil                            0x000000010c1e5126 diskutil + 57638
                        18  diskutil                            0x000000010c1e51cd diskutil + 57805
                        19  libdyld.dylib                       0x00007fff86bf87e1 start + 0
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: Saved crash report for diskutil[1061] version 680 to /Library/Logs/DiagnosticReports/diskutil_2014-02-23-111544_doghouse.crash
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: Removing excessive log: file://localhost/Library/Logs/DiagnosticReports/diskutil_2014-02-22-164711_dogh ouse.crash
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: failed looking up LS service ( scCreateSystemService returned MACH_PORT_NULL, called from SetupCoreApplicationServicesCommunicationPort, so using client-side NULL calls.
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: LaunchServices/5123589: Unable to lookup coreservices session port for session 0x186a0 uid=0 euid=0
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: failed looking up LS service ( scCreateSystemService returned MACH_PORT_NULL, called from SetupCoreApplicationServicesCommunicationPort, so using client-side NULL calls.
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: LaunchServices/5123589: Unable to lookup coreservices session port for session 0x186a0 uid=0 euid=0
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: failed looking up LS service ( scCreateSystemService returned MACH_PORT_NULL, called from SetupCoreApplicationServicesCommunicationPort, so using client-side NULL calls.
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: LaunchServices/5123589: Unable to lookup coreservices session port for session 0x186a0 uid=0 euid=0
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: failed looking up LS service ( scCreateSystemService returned MACH_PORT_NULL, called from SetupCoreApplicationServicesCommunicationPort, so using client-side NULL calls.
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: LaunchServices/5123589: Unable to lookup coreservices session port for session 0x186a0 uid=0 euid=0
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: failed looking up LS service ( scCreateSystemService returned MACH_PORT_NULL, called from SetupCoreApplicationServicesCommunicationPort, so using client-side NULL calls.
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: LaunchServices/5123589: Unable to lookup coreservices session port for session 0x186a0 uid=0 euid=0
    Feb 23 11:15:44 doghouse.local diskutil[1071]: -[__NSCFConstantString getBytes:length:]: unrecognized selector sent to instance 0x7fff7628bbe8
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: Saved crash report for diskutil[1067] version 680 to /Library/Logs/DiagnosticReports/diskutil_2014-02-23-111544-1_doghouse.crash
    Feb 23 11:15:44 doghouse.local diskutil[1071]: *** Terminating app due to uncaught exception 'NSInvalidArgumentException', reason: '-[__NSCFConstantString getBytes:length:]: unrecognized selector sent to instance 0x7fff7628bbe8'
              *** First throw call stack:
                        0   CoreFoundation                      0x00007fff91b2bb06 __exceptionPreprocess + 198
                        1   libobjc.A.dylib                     0x00007fff901403f0 objc_exception_throw + 43
                        2   CoreFoundation                      0x00007fff91bc240a -[NSObject(NSObject) doesNotRecognizeSelector:] + 186
                        3   CoreFoundation                      0x00007fff91b1a02e ___forwarding___ + 414
                        4   CoreFoundation                      0x00007fff91b19e18 _CF_forwarding_prep_0 + 232
                        5   diskutil                            0x0000000100e49550 diskutil + 83280
                        6   diskutil                            0x0000000100e480af diskutil + 77999
                        7   diskutil                            0x0000000100e45abe diskutil + 68286
                        8   diskutil                            0x0000000100e3b0ef diskutil + 24815
                        9   diskutil                            0x0000000100e43161 diskutil + 57697
                        10  Foundation                          0x00007fff8d29dd05 __NSFireDelayedPerform + 358
                        11  CoreFoundation                      0x00007fff91ae8804 __CFRUNLOOP_IS_CALLING_OUT_TO_A_TIMER_CALLBACK_FUNCTION__ + 20
                        12  CoreFoundation                      0x00007fff91ae831d __CFRunLoopDoTimer + 557
                        13  CoreFoundation                      0x00007fff91acdad9 __CFRunLoopRun + 1529
                        14  CoreFoundation                      0x00007fff91acd0e2 CFRunLoopRunSpecific + 290
                        15  Foundation                          0x00007fff8d2c57ee -[NSRunLoop(NSRunLoop) runMode:beforeDate:] + 268
                        16  Foundation                          0x00007fff8d25e1aa -[NSRunLoop(NSRunLoop) run] + 74
                        17  diskutil                            0x0000000100e43126 diskutil + 57638
                        18  diskutil                            0x0000000100e431cd diskutil + 57805
                        19  libdyld.dylib                       0x00007fff86bf87e1 start + 0
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: Removing excessive log: file://localhost/Library/Logs/DiagnosticReports/diskutil_2014-02-22-164712_dogh ouse.crash
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: failed looking up LS service ( scCreateSystemService returned MACH_PORT_NULL, called from SetupCoreApplicationServicesCommunicationPort, so using client-side NULL calls.
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: LaunchServices/5123589: Unable to lookup coreservices session port for session 0x186a0 uid=0 euid=0
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: failed looking up LS service ( scCreateSystemService returned MACH_PORT_NULL, called from SetupCoreApplicationServicesCommunicationPort, so using client-side NULL calls.
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: LaunchServices/5123589: Unable to lookup coreservices session port for session 0x186a0 uid=0 euid=0
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: failed looking up LS service ( scCreateSystemService returned MACH_PORT_NULL, called from SetupCoreApplicationServicesCommunicationPort, so using client-side NULL calls.
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: LaunchServices/5123589: Unable to lookup coreservices session port for session 0x186a0 uid=0 euid=0
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: failed looking up LS service ( scCreateSystemService returned MACH_PORT_NULL, called from SetupCoreApplicationServicesCommunicationPort, so using client-side NULL calls.
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: LaunchServices/5123589: Unable to lookup coreservices session port for session 0x186a0 uid=0 euid=0
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: failed looking up LS service ( scCreateSystemService returned MACH_PORT_NULL, called from SetupCoreApplicationServicesCommunicationPort, so using client-side NULL calls.
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: LaunchServices/5123589: Unable to lookup coreservices session port for session 0x186a0 uid=0 euid=0
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: Saved crash report for diskutil[1071] version 680 to /Library/Logs/DiagnosticReports/diskutil_2014-02-23-111544-2_doghouse.crash
    Feb 23 11:15:44 doghouse.local ReportCrash[1064]: Removing excessive log: file://localhost/Library/Logs/DiagnosticReports/diskutil_2014-02-23-093307_dogh ouse.crash
    diskutil crash report
    Process:         diskutil [1061]
    Path:            /usr/sbin/diskutil
    Identifier:      diskutil
    Version:         680
    Code Type:       X86-64 (Native)
    Parent Process:  sh [1060]
    User ID:         0
    Date/Time:       2014-02-23 11:15:43.719 -0800
    OS Version:      Mac OS X 10.8.5 (12F45)
    Report Version:  10
    Crashed Thread:  0  Dispatch queue: com.apple.main-thread
    Exception Type:  EXC_CRASH (SIGABRT)
    Exception Codes: 0x0000000000000000, 0x0000000000000000
    Application Specific Information:
    *** Terminating app due to uncaught exception 'NSInvalidArgumentException', reason: '-[__NSCFConstantString getBytes:length:]: unrecognized selector sent to instance 0x7fff7628bbe8'
    terminate called throwing an exception
    abort() called
    Application Specific Backtrace 1:
    0   CoreFoundation                      0x00007fff91b2bb06 __exceptionPreprocess + 198
    1   libobjc.A.dylib                     0x00007fff901403f0 objc_exception_throw + 43
    2   CoreFoundation                      0x00007fff91bc240a -[NSObject(NSObject) doesNotRecognizeSelector:] + 186
    3   CoreFoundation                      0x00007fff91b1a02e ___forwarding___ + 414
    4   CoreFoundation                      0x00007fff91b19e18 _CF_forwarding_prep_0 + 232
    5   diskutil                            0x000000010124a550 diskutil + 83280
    6   diskutil                            0x00000001012490af diskutil + 77999
    7   diskutil                            0x0000000101246abe diskutil + 68286
    8   diskutil                            0x000000010123c0ef diskutil + 24815
    9   diskutil                            0x0000000101244161 diskutil + 57697
    10  Foundation                          0x00007fff8d29dd05 __NSFireDelayedPerform + 358
    11  CoreFoundation                      0x00007fff91ae8804 __CFRUNLOOP_IS_CALLING_OUT_TO_A_TIMER_CALLBACK_FUNCTION__ + 20
    12  CoreFoundation                      0x00007fff91ae831d __CFRunLoopDoTimer + 557
    13  CoreFoundation                      0x00007fff91acdad9 __CFRunLoopRun + 1529
    14  CoreFoundation                      0x00007fff91acd0e2 CFRunLoopRunSpecific + 290
    15  Foundation                          0x00007fff8d2c57ee -[NSRunLoop(NSRunLoop) runMode:beforeDate:] + 268
    16  Foundation                          0x00007fff8d25e1aa -[NSRunLoop(NSRunLoop) run] + 74
    17  diskutil                            0x0000000101244126 diskutil + 57638
    18  diskutil                            0x00000001012441cd diskutil + 57805
    19  libdyld.dylib                       0x00007fff86bf87e1 start + 0
    Thread 0 Crashed:: Dispatch queue: com.apple.main-thread
    0   libsystem_kernel.dylib                  0x00007fff86519212 __pthread_kill + 10
    1   libsystem_c.dylib                       0x00007fff8a31ab24 pthread_kill + 90
    2   libsystem_c.dylib                       0x00007fff8a35ef61 abort + 143
    3   libc++abi.dylib                         0x00007fff85dc39eb abort_message + 257
    4   libc++abi.dylib                         0x00007fff85dc139a default_terminate() + 28
    5   libobjc.A.dylib                         0x00007fff90140873 _objc_terminate() + 91
    6   libc++abi.dylib                         0x00007fff85dc13c9 safe_handler_caller(void (*)()) + 8
    7   libc++abi.dylib                         0x00007fff85dc1424 std::terminate() + 16
    8   libc++abi.dylib                         0x00007fff85dc261b __cxa_rethrow + 85
    9   libobjc.A.dylib                         0x00007fff90140575 objc_exception_rethrow + 40
    10  com.apple.CoreFoundation                0x00007fff91acd146 CFRunLoopRunSpecific + 390
    11  com.apple.Foundation                    0x00007fff8d2c57ee -[NSRunLoop(NSRunLoop) runMode:beforeDate:] + 268
    12  com.apple.Foundation                    0x00007fff8d25e1aa -[NSRunLoop(NSRunLoop) run] + 74
    13  diskutil                                0x0000000101244126 0x101236000 + 57638
    14  diskutil                                0x00000001012441cd 0x101236000 + 57805
    15  libdyld.dylib                           0x00007fff86bf87e1 start + 1
    Thread 1:: Dispatch queue: com.apple.libdispatch-manager
    0   libsystem_kernel.dylib                  0x00007fff86519d16 kevent + 10
    1   libdispatch.dylib                       0x00007fff8a0dddea _dispatch_mgr_invoke + 883
    2   libdispatch.dylib                       0x00007fff8a0dd9ee _dispatch_mgr_thread + 54
    Thread 2:
    0   libsystem_kernel.dylib                  0x00007fff865196d6 __workq_kernreturn + 10
    1   libsystem_c.dylib                       0x00007fff8a31bf1c _pthread_workq_return + 25
    2   libsystem_c.dylib                       0x00007fff8a31bce3 _pthread_wqthread + 412
    3   libsystem_c.dylib                       0x00007fff8a306191 start_wqthread + 13
    Thread 3:
    0   libsystem_kernel.dylib                  0x00007fff865196d6 __workq_kernreturn + 10
    1   libsystem_c.dylib                       0x00007fff8a31bf1c _pthread_workq_return + 25
    2   libsystem_c.dylib                       0x00007fff8a31bce3 _pthread_wqthread + 412
    3   libsystem_c.dylib                       0x00007fff8a306191 start_wqthread + 13
    Thread 4:
    0   libsystem_kernel.dylib                  0x00007fff865196d6 __workq_kernreturn + 10
    1   libsystem_c.dylib                       0x00007fff8a31bf1c _pthread_workq_return + 25
    2   libsystem_c.dylib                       0x00007fff8a31bce3 _pthread_wqthread + 412
    3   libsystem_c.dylib                       0x00007fff8a306191 start_wqthread + 13
    Thread 0 crashed with X86 Thread State (64-bit):
      rax: 0x0000000000000000  rbx: 0x0000000000000006  rcx: 0x00007fff5e9c9ad8  rdx: 0x0000000000000000
      rdi: 0x0000000000000707  rsi: 0x0000000000000006  rbp: 0x00007fff5e9c9b00  rsp: 0x00007fff5e9c9ad8
       r8: 0x00007fff764be278   r9: 0x00007fff5e9c9ae0  r10: 0x0000000020000000  r11: 0x0000000000000206
      r12: 0x00007fff5e9c9c60  r13: 0x0000000000000001  r14: 0x00007fff764bf180  r15: 0x00007fff5e9c9b40
      rip: 0x00007fff86519212  rfl: 0x0000000000000206  cr2: 0x00007fff764b7ff0
    Logical CPU: 0
    Binary Images:
           0x101236000 -        0x10126efff  diskutil (680) <47174BB8-7EAC-39F7-96F7-99FE93C9CAF3> /usr/sbin/diskutil
        0x7fff60e36000 -     0x7fff60e6a93f  dyld (210.2.3) <6900F2BA-DB48-3B78-B668-58FC0CF6BCB8> /usr/lib/dyld
        0x7fff85d6f000 -     0x7fff85d6ffff  libkeymgr.dylib (25) <CC9E3394-BE16-397F-926B-E579B60EE429> /usr/lib/system/libkeymgr.dylib
        0x7fff85dc0000 -     0x7fff85de5ff7  libc++abi.dylib (26) <D86169F3-9F31-377A-9AF3-DB17142052E4> /usr/lib/libc++abi.dylib
        0x7fff85de6000 -     0x7fff85e4eff7  libc++.1.dylib (65.1) <20E31B90-19B9-3C2A-A9EB-474E08F9FE05> /usr/lib/libc++.1.dylib
        0x7fff85e4f000 -     0x7fff85ef5ff7  com.apple.CoreServices.OSServices (557.6 - 557.6) <FFDDD2D8-690D-388F-A48F-4750A792D2CD> /System/Library/Frameworks/CoreServices.framework/Versions/A/Frameworks/OSServi ces.framework/Versions/A/OSServices
        0x7fff85f54000 -     0x7fff85f62ff7  libkxld.dylib (2050.48.12) <B8F7ED1F-CF84-3777-9183-0A1C513DF81F> /usr/lib/system/libkxld.dylib
        0x7fff861de000 -     0x7fff86353ff7  com.apple.CFNetwork (596.5 - 596.5) <22372475-6EF4-3A04-83FC-C061FE4717B3> /System/Library/Frameworks/CFNetwork.framework/Versions/A/CFNetwork
        0x7fff86354000 -     0x7fff863d5fff  com.apple.Metadata (10.7.0 - 707.12) <69E3EEF7-8B7B-3652-8320-B8E885370E56> /System/Library/Frameworks/CoreServices.framework/Versions/A/Frameworks/Metadat a.framework/Versions/A/Metadata
        0x7fff86468000 -     0x7fff86470ff7  libsystem_dnssd.dylib (379.38.1) <BDCB8566-0189-34C0-9634-35ABD3EFE25B> /usr/lib/system/libsystem_dnssd.dylib
        0x7fff86499000 -     0x7fff86506ff7  com.apple.datadetectorscore (4.1 - 269.3) <5775F0DB-87D6-310D-8B03-E2AD729EFB28> /System/Library/PrivateFrameworks/DataDetectorsCore.framework/Versions/A/DataDe tectorsCore
        0x7fff86507000 -     0x7fff86522ff7  libsystem_kernel.dylib (2050.48.12) <4B7993C3-F62D-3AC1-AF92-414A0D6EED5E> /usr/lib/system/libsystem_kernel.dylib
        0x7fff865b1000 -     0x7fff865b2ff7  libremovefile.dylib (23.2) <6763BC8E-18B8-3AD9-8FFA-B43713A7264F> /usr/lib/system/libremovefile.dylib
        0x7fff86764000 -     0x7fff86769fff  libcache.dylib (57) <65187C6E-3FBF-3EB8-A1AA-389445E2984D> /usr/lib/system/libcache.dylib
        0x7fff86784000 -     0x7fff86785fff  libDiagnosticMessagesClient.dylib (8) <8548E0DC-0D2F-30B6-B045-FE8A038E76D8> /usr/lib/libDiagnosticMessagesClient.dylib
        0x7fff86bf6000 -     0x7fff86bf9ff7  libdyld.dylib (210.2.3) <F59367C9-C110-382B-A695-9035A6DD387E> /usr/lib/system/libdyld.dylib
        0x7fff8715b000 -     0x7fff8715bfff  com.apple.vecLib (3.8 - vecLib 3.8) <6CBBFDC4-415C-3910-9558-B67176447789> /System/Library/Frameworks/vecLib.framework/Versions/A/vecLib
        0x7fff871a8000 -     0x7fff87235ff7  com.apple.SearchKit (1.4.0 - 1.4.0) <C7F43889-F8BF-3CB9-AD66-11AEFCBCEDE7> /System/Library/Frameworks/CoreServices.framework/Versions/A/Frameworks/SearchK it.framework/Versions/A/SearchKit
        0x7fff87236000 -     0x7fff87243fff  libbz2.1.0.dylib (29) <CE9785E8-B535-3504-B392-82F0064D9AF2> /usr/lib/libbz2.1.0.dylib
        0x7fff872d9000 -     0x7fff87373fff  libvMisc.dylib (380.10) <A7F12764-A94C-36EB-88E0-F826F5AF55B4> /System/Library/Frameworks/Accelerate.framework/Versions/A/Frameworks/vecLib.fr amework/Versions/A/libvMisc.dylib
        0x7fff87455000 -     0x7fff87455fff  com.apple.CoreServices (57 - 57) <9DD44CB0-C644-35C3-8F57-0B41B3EC147D> /System/Library/Frameworks/CoreServices.framework/Versions/A/CoreServices
        0x7fff87874000 -     0x7fff87947ff7  com.apple.DiscRecording (7.0 - 7000.2.4) <6DCA9535-E276-3D77-BEB3-296B537AA6BB> /System/Library/Frameworks/DiscRecording.framework/Versions/A/DiscRecording
        0x7fff879ab000 -     0x7fff879aefff  libutil.dylib (30) <EF3340B2-9A53-3D5E-B9B4-BDB5EEECC178> /usr/lib/libutil.dylib
        0x7fff87da3000 -     0x7fff87da5ff7  com.apple.EFILogin (2.0 - 2) <51A470D7-1F72-3369-AF0F-AD2340B42C12> /System/Library/PrivateFrameworks/EFILogin.framework/Versions/A/EFILogin
        0x7fff880b1000 -     0x7fff880e9fff  libncurses.5.4.dylib (37.3) <68D5B5F5-8252-3F1E-AFF1-C6AFE145DBC1> /usr/lib/libncurses.5.4.dylib
        0x7fff881ed000 -     0x7fff881faff7  com.apple.NetAuth (4.0 - 4.0) <F5BC7D7D-AF28-3C83-A674-DADA48FF7810> /System/Library/PrivateFrameworks/NetAuth.framework/Versions/A/NetAuth
        0x7fff88571000 -     0x7fff8859fff7  libsystem_m.dylib (3022.6) <B434BE5C-25AB-3EBD-BAA7-5304B34E3441> /usr/lib/system/libsystem_m.dylib
        0x7fff887e7000 -     0x7fff887e8ff7  libSystem.B.dylib (169.3) <5ED23C27-47AF-3C93-984A-172751CF745A> /usr/lib/libSystem.B.dylib
        0x7fff887e9000 -     0x7fff8883aff7  com.apple.SystemConfiguration (1.12.2 - 1.12.2) <581BF463-C15A-363B-999A-E830222FA925> /System/Library/Frameworks/SystemConfiguration.framework/Versions/A/SystemConfi guration
        0x7fff8883b000 -     0x7fff88b52ff7  com.apple.CoreServices.CarbonCore (1037.6 - 1037.6) <1E567A52-677F-3168-979F-5FBB0818D52B> /System/Library/Frameworks/CoreServices.framework/Versions/A/Frameworks/CarbonC ore.framework/Versions/A/CarbonCore
        0x7fff88b53000 -     0x7fff88b54ff7  libsystem_sandbox.dylib (220.3) <B739DA63-B675-387A-AD84-412A651143C0> /usr/lib/system/libsystem_sandbox.dylib
        0x7fff88be0000 -     0x7fff88bf3ff7  libbsm.0.dylib (32) <F497D3CE-40D9-3551-84B4-3D5E39600737> /usr/lib/libbsm.0.dylib
        0x7fff88dd0000 -     0x7fff88dd1fff  libsystem_blocks.dylib (59) <D92DCBC3-541C-37BD-AADE-ACC75A0C59C8> /usr/lib/system/libsystem_blocks.dylib
        0x7fff892df000 -     0x7fff892e5fff  libmacho.dylib (829) <BF332AD9-E89F-387E-92A4-6E1AB74BD4D9> /usr/lib/system/libmacho.dylib
        0x7fff892e6000 -     0x7fff89335ff7  libcorecrypto.dylib (106.2) <CE0C29A3-C420-339B-ADAA-52F4683233CC> /usr/lib/system/libcorecrypto.dylib
        0x7fff89336000 -     0x7fff89536fff  libicucore.A.dylib (491.11.3) <5783D305-04E8-3D17-94F7-1CEAFA975240> /usr/lib/libicucore.A.dylib
        0x7fff89537000 -     0x7fff89537fff  libOpenScriptingUtil.dylib (148.3) <F8681222-0969-3B10-8BCE-C55A4B9C520C> /usr/lib/libOpenScriptingUtil.dylib
        0x7fff89538000 -     0x7fff89581ff7  com.apple.DiskManagement (5.3.1 - 680) <5438A1FF-B92C-3D28-A8E4-FB41F03144C2> /System/Library/PrivateFrameworks/DiskManagement.framework/Versions/A/DiskManag ement
        0x7fff89589000 -     0x7fff895abff7  libxpc.dylib (140.43) <70BC645B-6952-3264-930C-C835010CCEF9> /usr/lib/system/libxpc.dylib
        0x7fff895b6000 -     0x7fff895cdfff  com.apple.CFOpenDirectory (10.8 - 151.10) <F7AD9844-559A-366E-8192-BB4FCF9EE7A3> /System/Library/Frameworks/OpenDirectory.framework/Versions/A/Frameworks/CFOpen Directory.framework/Versions/A/CFOpenDirectory
        0x7fff895ce000 -     0x7fff895d9fff  libsystem_notify.dylib (98.5) <C49275CC-835A-3207-AFBA-8C01374927B6> /usr/lib/system/libsystem_notify.dylib
        0x7fff8960f000 -     0x7fff89614fff  libcompiler_rt.dylib (30) <08F8731D-5961-39F1-AD00-4590321D24A9> /usr/lib/system/libcompiler_rt.dylib
        0x7fff899f3000 -     0x7fff89a3fff7  libauto.dylib (185.4) <AD5A4CE7-CB53-313C-9FAE-673303CC2D35> /usr/lib/libauto.dylib
        0x7fff89b9a000 -     0x7fff89b9cff7  libunc.dylib (25) <92805328-CD36-34FF-9436-571AB0485072> /usr/lib/system/libunc.dylib
        0x7fff89bd8000 -     0x7fff89c09ff7  com.apple.DictionaryServices (1.2 - 184.4) <FB0540FF-5034-3591-A28D-6887FBC220F7> /System/Library/Frameworks/CoreServices.framework/Versions/A/Frameworks/Diction aryServices.framework/Versions/A/DictionaryServices
        0x7fff8a01f000 -     0x7fff8a0afff7  libCoreStorage.dylib (296.18.2) <2FFB6BCA-3033-3AC1-BCE4-ED102DCBECD5> /usr/lib/libCoreStorage.dylib
        0x7fff8a0d9000 -     0x7fff8a0eeff7  libdispatch.dylib (228.23) <D26996BF-FC57-39EB-8829-F63585561E09> /usr/lib/system/libdispatch.dylib
        0x7fff8a0ef000 -     0x7fff8a11afff  libxslt.1.dylib (11.3) <441776B8-9130-3893-956F-39C85FFA644F> /usr/lib/libxslt.1.dylib
        0x7fff8a2e9000 -     0x7fff8a2f3fff  libcsfde.dylib (296.18.2) <08092C5B-2171-3C1D-A98F-CF499A315DDC> /usr/lib/libcsfde.dylib
        0x7fff8a305000 -     0x7fff8a3d1ff7  libsystem_c.dylib (825.40.1) <543B05AE-CFA5-3EFE-8E58-77225411BA6B> /usr/lib/system/libsystem_c.dylib
        0x7fff8a5c9000 -     0x7fff8a628fff  com.apple.AE (645.6 - 645.6) <44F403C1-660A-3543-AB9C-3902E02F936F> /System/Library/Frameworks/CoreServices.framework/Versions/A/Frameworks/AE.fram ework/Versions/A/AE
        0x7fff8a679000 -     0x7fff8a776fff  libsqlite3.dylib (138.1) <ADE9CB98-D77D-300C-A32A-556B7440769F> /usr/lib/libsqlite3.dylib
        0x7fff8a8e3000 -     0x7fff8a9e0ff7  libxml2.2.dylib (22.3) <47B09CB2-C636-3024-8B55-6040F7829B4C> /usr/lib/libxml2.2.dylib
        0x7fff8afa9000 -     0x7fff8afdffff  libsystem_info.dylib (406.17) <4FFCA242-7F04-365F-87A6-D4EFB89503C1> /usr/lib/system/libsystem_info.dylib
        0x7fff8afe6000 -     0x7fff8afeefff  liblaunch.dylib (442.26.2) <2F71CAF8-6524-329E-AC56-C506658B4C0C> /usr/lib/system/liblaunch.dylib
        0x7fff8b2b7000 -     0x7fff8b368fff  com.apple.LaunchServices (539.9 - 539.9) <07FC6766-778E-3479-8F28-D2C9917E1DD1> /System/Library/Frameworks/CoreServices.framework/Versions/A/Frameworks/LaunchS ervices.framework/Versions/A/LaunchServices
        0x7fff8b3bc000 -     0x7fff8b3c0ff7  com.apple.TCC (1.0 - 1) <F2F3B753-FC73-3543-8BBE-859FDBB4D6A6> /System/Library/PrivateFrameworks/TCC.framework/Versions/A/TCC
        0x7fff8c051000 -     0x7fff8c0b9fff  libvDSP.dylib (380.10) <3CA154A3-1BE5-3CF4-BE48-F0A719A963BB> /System/Library/Frameworks/Accelerate.framework/Versions/A/Frameworks/vecLib.fr amework/Versions/A/libvDSP.dylib
        0x7fff8c15b000 -     0x7fff8c17cff7  libCRFSuite.dylib (33) <736ABE58-8DED-3289-A042-C25AF7AE5B23> /usr/lib/libCRFSuite.dylib
        0x7fff8c1bc000 -     0x7fff8c1c2ff7  libunwind.dylib (35.1) <21703D36-2DAB-3D8B-8442-EAAB23C060D3> /usr/lib/system/libunwind.dylib
        0x7fff8c58d000 -     0x7fff8c984fff  libLAPACK.dylib (1073.4) <D632EC8B-2BA0-3853-800A-20DA00A1091C> /System/Library/Frameworks/Accelerate.framework/Versions/A/Frameworks/vecLib.fr amework/Versions/A/libLAPACK.dylib
        0x7fff8c985000 -     0x7fff8c993ff7  libsystem_network.dylib (77.10) <0D99F24E-56FE-380F-B81B-4A4C630EE587> /usr/lib/system/libsystem_network.dylib
        0x7fff8c994000 -     0x7fff8c99bfff  libcopyfile.dylib (89) <876573D0-E907-3566-A108-577EAD1B6182> /usr/lib/system/libcopyfile.dylib
        0x7fff8c99c000 -     0x7fff8c9aafff  libcommonCrypto.dylib (60027) <BAAFE0C9-BB86-3CA7-88C0-E3CBA98DA06F> /usr/lib/system/libcommonCrypto.dylib
        0x7fff8ccbc000 -     0x7fff8cf8dff7  com.apple.security (7.0 - 55179.13) <F428E306-C407-3B55-BA82-E58755E8A76F> /System/Library/Frameworks/Security.framework/Versions/A/Security
        0x7fff8d22a000 -     0x7fff8d589fff  com.apple.Foundation (6.8 - 945.18) <1D7E58E6-FA3A-3CE8-AC85-B9D06B8C0AA0> /System/Library/Frameworks/Foundation.framework/Versions/C/Foundation
        0x7fff8d939000 -     0x7fff8d950fff  com.apple.GenerationalStorage (1.1 - 132.3) <FD4A84B3-13A8-3C60-A59E-25A361447A17> /System/Library/PrivateFrameworks/GenerationalStorage.framework/Versions/A/Gene rationalStorage
        0x7fff8d951000 -     0x7fff8d952fff  liblangid.dylib (116) <864C409D-D56B-383E-9B44-A435A47F2346> /usr/lib/liblangid.dylib
        0x7fff8d953000 -     0x7fff8d95afff  com.apple.NetFS (5.0 - 4.0) <82E24B9A-7742-3DA3-9E99-ED267D98C05E> /System/Library/Frameworks/NetFS.framework/Versions/A/NetFS
        0x7fff8d968000 -     0x7fff8d9d1fff  libstdc++.6.dylib (56) <EAA2B53E-EADE-39CF-A0EF-FB9D4940672A> /usr/lib/libstdc++.6.dylib
        0x7fff8dbde000 -     0x7fff8dc4cff7  com.apple.framework.IOKit (2.0.1 - 755.42.1) <A90038ED-48F2-3CC9-A042-53A3D7985844> /System/Library/Frameworks/IOKit.framework/Versions/A/IOKit
        0x7fff8e11b000 -     0x7fff8e11dfff  libquarantine.dylib (52.1) <143B726E-DF47-37A8-90AA-F059CFD1A2E4> /usr/lib/system/libquarantine.dylib
        0x7fff9012f000 -     0x7fff9024792f  libobjc.A.dylib (532.2) <90D31928-F48D-3E37-874F-220A51FD9E37> /usr/lib/libobjc.A.dylib
        0x7fff91567000 -     0x7fff91568ff7  libdnsinfo.dylib (453.19) <14202FFB-C3CA-3FCC-94B0-14611BF8692D> /usr/lib/system/libdnsinfo.dylib
        0x7fff91952000 -     0x7fff919b5fff  com.apple.audio.CoreAudio (4.1.2 - 4.1.2) <FEAB83AB-1DE5-3813-BA48-7A7F2374CCF0> /System/Library/Frameworks/CoreAudio.framework/Versions/A/CoreAudio
        0x7fff91a98000 -     0x7fff91c82ff7  com.apple.CoreFoundation (6.8 - 744.19) <0F7403CA-2CB8-3D0A-992B-679701DF27CA> /System/Library/Frameworks/CoreFoundation.framework/Versions/A/CoreFoundation
        0x7fff91c83000 -     0x7fff91e09fff  libBLAS.dylib (1073.4) <C102C0F6-8CB6-3B49-BA6B-2EB61F0B2784> /System/Library/Frameworks/Accelerate.framework/Versions/A/Frameworks/vecLib.fr amework/Versions/A/libBLAS.dylib
        0x7fff91e13000 -     0x7fff91e25ff7  libz.1.dylib (43) <2A1551E8-A272-3DE5-B692-955974FE1416> /usr/lib/libz.1.dylib
        0x7fff91e76000 -     0x7fff91e7cfff  com.apple.DiskArbitration (2.5.2 - 2.5.2) <C713A35A-360E-36CE-AC0A-25C86A3F50CA> /System/Library/Frameworks/DiskArbitration.framework/Versions/A/DiskArbitration
        0x7fff91f14000 -     0x7fff91f54ff7  com.apple.MediaKit (14 - 687) <8AAA8CC3-3ACD-34A5-9E57-9B24AD8AFD4D> /System/Library/PrivateFrameworks/MediaKit.framework/Versions/A/MediaKit
        0x7fff92028000 -     0x7fff92037ff7  libxar.1.dylib (105) <370ED355-E516-311E-BAFD-D80633A84BE1> /usr/lib/libxar.1.dylib
        0x7fff921bd000 -     0x7fff921c1fff  libpam.2.dylib (20) <C8F45864-5B58-3237-87E1-2C258A1D73B8> /usr/lib/libpam.2.dylib
        0x7fff921c2000 -     0x7fff92314fff  com.apple.audio.toolbox.AudioToolbox (1.9.2 - 1.9.2) <DC5F3D1B-036A-37DE-BC24-7636DC95EA1C> /System/Library/Frameworks/AudioToolbox.framework/Versions/A/AudioToolbox
    External Modification Summary:
      Calls made by other processes targeting this process:
        task_for_pid: 0
        thread_create: 0
        thread_set_state: 0
      Calls made by this process:
        task_for_pid: 0
        thread_create: 0
        thread_set_state: 0
      Calls made by all processes on this machine:
        task_for_pid: 240
        thread_create: 0
        thread_set_state: 0
    VM Region Summary:
    ReadOnly portion of Libraries: Total=89.5M resident=64.1M(72%) swapped_out_or_unallocated=25.4M(28%)
    Writable regions: Total=82.6M written=784K(1%) resident=1340K(2%) swapped_out=0K(0%) unallocated=81.3M(98%)
    REGION TYPE                      VIRTUAL
    ===========                      =======
    MALLOC                             72.3M
    MALLOC guard page                    32K
    STACK GUARD                        56.0M
    Stack                              10.0M
    VM_ALLOCATE                           8K
    __DATA                             3472K
    __LINKEDIT                         52.1M
    __TEXT                             37.4M
    __UNICODE                           544K
    mapped file                        18.1M
    shared memory                        12K
    ===========                      =======
    TOTAL                             250.0M

    That kind of crash is usually caused by system corruption. I suggest you reinstall.

Maybe you are looking for

  • 5800 V40 Music palyer problem

    I updated my 5800 to new v40 firmware, but now getting wired problem in Music player, its intermitently gets stuck in Music Player first screen where its displays 'Artists, Albums' etc. I am not even able to exit music player using 'Exit' option. I h

  • Question Mark in folder window header

    I just noticed a question mark "?" at the top in the header area in all my folder windows. http://www.sasnet.com/question.png Has anyone seen this before or know what it is, or what to do about it? Steven

  • Problem with connect

    [color="#993399">Ok, so this question has been posted a lot...but no one ever answers.[color="#993399">?[color="#993399">I've dowloaded the latest firmware and Windows Media Player, but my Creative MediaSource just won't recognize my Zen Micro, even

  • How to use gradient colors in Muse?

    Is there a way to use gradient colors in Muse?  I keep reading that you can but there is no instructions that I can find how to do it. 

  • OD Group members not synchronized to mailing lists

    We have some Groups in the SLS OD that we configured as wikis to distribute Dokuments to the members. Last year the configuration of the wiki vanished from the workgroup manager and I think since then the members of the groups were no longer synced w