Drop frames when printing to tape !

HI
I would like some help please !!!
The problem is when I print to tape I keep on getting drop frames
Here is the run down
The video is normal some where around 1hr 30 min 2hrs long
3 layers maximum
The audio is four layers
I have tried “Nesting all items” and then printing to video (it last a little longer but I still get the same problem)
My system stats are as follows
G5 Dual 2.7 with 3.5GB Ram, 10.4.8, FCP 5.04 650GB Internal HD and 900GB Sata HD
Thanks

Maurice,
make sure all your audio is 48K
close all sequences other than the one you are using to print to tape
Try exporting your project as a QT movie then place it back on a new timeline and print to tape that way
make sure your hard drives are not going to sleep
try recording from the timeline rather than using the print to tape function

Similar Messages

Drop Frames when Printing to Video

I know there are a lot of topics on drop frames, but I couldn't find any that met my specific set of circumstances.
My video plays fine and there is no red bar indicating that something has to be rendered. However, when I try to print to video, ten seconds in, the project is aborted and a drop frame error is given.
Is there anything I can do to get around this?
Thanks.

I don't know the specs of your machine however...
Alternatevely you could open the RT dropdown menu
and turn playback video quality and playback frame rate to the minimum and close
other projects.

Avoiding Dropped Frames While Printing to Tape

Hi everyone. Quick question. I'm trying to avoid dropped frames during playback while printing to Mini DV, and I just read the article everyone links to about ways to do it.
Some solutions are to reduce playback quality, lower framerate, change RT to unlimited, turn on Play Base Layer Only, etc. I was just wondering if any or all of these solutions will affect the quality of my sequence on Mini DV. I see that the lower framerate does, but the others, I can't really tell on my small camera screen.
Thanks.

... reduce playback quality, lower framerate, change RT to unlimited, turn on Play Base Layer Only, etc...
Most of these settings are for playback only and are ignored for printing to video/edit to tape.
Did you read this thread?:
http://discussions.apple.com/thread.jspa?threadID=1403093&tstart=0
Jerry's tip to export a Selfcontained movie first is a very good workaround.
Andy's tips are very important too.
And finally, if your footage is on an external firewire drive, I want to tell you the importance of having an extra firewire card to make sure that your camera is on another firewire bus than your disk(s). (On your G5 all firewire ports are on the same bus and the camera slows down the bitrate of the whole chain. And so can cause dropframe problems)
Rienk

Flash frame when printing to tape?

Ok, this has never happened to me before, I have an hour long show. The whole project is edited and rendered out in one quicktime movie.
I'm using the final QT movie to edit to tape. At the end of a dissolve I am getting a Flash frame, the funny thing is its only happening on the tape. I have gone through the sequence frame-by-frame and there is no indication of an added frame or
bad edit anywhere. Does anyone know why I would get a Flash frame only when I print to Tape?

are you monitoring on a NTSC monitor or your computer. I've seen this when the flashframe is on a field the computer monitor isn't showing, but the ntsc mon will show it. The other thing is when your deck is brought out of record by hitting stop without rolling enough black prior to stopping this can happen but it sounds like you are seeing this in the sequence somewhere not at the end

Not rendering - Getting dropped frames when exporting to tape

I am trying to export my project to Mini DV tape. I have been successful before, but am continually getting dropped frames. I noticed that the sections that are getting dropped frames are showing that it is not rendered (red bar). I have tried rendering them several times, but still show the red bar. I am using a PowerMac G5, Dual 2 GHZ processor with 3GB RAM. The footage is on a Lacie Firewire 800 external hardrive and there is almost 200 GB of free space. I do get occasional dropped frames, but not as often as I am now.

Is there anything else I can do? When I get the Warning - Dropped frames, it suggests turning off "Unlimited RT", which I have and set to "Safe" because I was getting dropped frames. Will this affect the quality when exporting? I have set the Video Quality to "Dynamic" and Frame Rate "Full" and Record "Full Quality". Do any of these settings need to be changed? Lowering your compression data rate (I'm not sure what that is), Closing open sequences (which I've done), Lowering the preference for real-time audio tracks (how do I do that and again will it affect the quality?), Increasing the speed of your system and/or disk drives and/or network connection (Is there a way for me to do that?)

Dropped frames when playing section in the timeline w/audio, Viewer plays fine. Plays for 1 sec, no sound, nothing on audio meters. Problem out the blue, made no conscious changes. FCP 7.0.3. iMac, 2.7 GHz Intel Core i5. OS10.8.4. Thanx.

New to FCP. Dropped frames when playing section in the timeline w/audio, Viewer plays fine tho. Plays for bout 1 sec with no sound, nothing showing coming through the audio meters. Problem came out the blue, made no conscious changes to settings. FCP 7.0.3. iMac, 2.7 GHz Intel Core i5. OS10.8.4. If any other info needed please let me know, will be happy to provide it. Thanx.

Thank you for the help. Below is my Source footage and sequence settings.
The other footage I have on the timeline is an mp3 file made in Garage Band and some footage I sent to Motion to edit. I do have some offline media on there since I switched computers but FCP had been working fine for a few months with it on there. I have not tried trashing my FCP Preferences. If I did would I have to back up my project?

Dropped frames when importing from sony dcr-hc52

hey all,
i'm getting a lot of dropped frames when importing from my sony cdr-hc52. anyone had this experience? is there a setting i'm missing that would correct this?
thanks in advance,
filmgrrrl

Hello kellyfromkenley, Depending on how you move the video or share the video from iMovie to iDVD it can make a big difference. One way is to go to the Share Menu > Share to iDVD. But the better is to Share to Media Browser instead. Try this:
Go back to iMovie and open your Project in Project Library.
Go to Share Menu > Share to Media Browser
Choose the Large size and let it run until it finishes
Quit iMovie and open iDVD.
In iDVD click on the Media Button, then click on the Movies button and look for your project under the iMovie star icon in the Media Browser itself.
Drag that project icon into the iDVD project window and burn another disk
I think you'll see an increase in the visual quality using this method.
The reason this has an effect on the visual quality is there's a whole different set of operations performed on the video when you first Share to Media Browser. The side effect of those changes in steps is a much better looking DVD from your iMovie project.

Why does Premiere Pro stop, or drop frames when using the Timecode Effect.

The Timecode Effect is gpu accelerated, the render bar is yellow and it still drops frames.
If it drops frames on a yellow bar, how can I ever trust it to print to tape? It wouldn't be a problem if I could say render the yellow sections of my edit, but it won't because the bar is not red. Very frustrating!
Running 64bit windows 7;
gtx470 graphics card;
12GB of memory (9 reserved for Premiere)
Raid 0 _ Speed Tested Excellent
working with uncompressed black magic 1080i AVI's
It seems to happen when I have overlapping clips with the Timecode Effect on one or both. Plays fine if just a single clip with the effect.
Any help would be great, hopefully I'm just missing something simple..

Harm,
Here is a capture of my speed test. I do have 4 disks on a raid 0, very little data on the drives. I have run 3 tracks of HD with different levels of opacity with no problem. I do crash the drives when I add the forth. So I would like to think that two tracks with accelerated effect should be fairly simple to playback. Am I wrong to be thinking that way? Also only working with 8 bit, This test is for 10 and up.
The read comes in above 500 mb/s. It was on the way up when I captured it.

Firewire failure when printing to tape with DSR-11

I have a problem printing to tape with bigger projects. I can't put out to tape more then around 20mins, then the either sound or sound and picture drop.
I have everything rendered and exported to a new, not-selfstanding final cut pro file (Quicktime export) and reimported and put in a new sequence. As I found out, this causes the least problems with complex sequences, sounds etc.
The problem might be related to a occasional image drop out while working on the timeline and watching on the external monitor (through firwire). After a while the connection fails and I have to switch from "all frames" to "none" and back in order to continue watching through the deck.
I checked all settings I know, could it be a hardware problem or a problem with the protocoll of the sony DSR-11 deck (I use DVCAM).
Thanks for your time !
klaus

Hello Klaus,
I also own and operate a Sony DSR-11 which has worked out just fine for me. However, I recently bought a new firewire cable to replace my 4-year old cable and discovered that you get what you pay for when it comes to cables. After a while the new cable would slip out of the back of the DSR-11 and I would lose my connection during editing and playback. As part of the troubleshooting process I replaced the firewire cable with a "better" one and no longer experience this problem. My only critisism of the DSR-11 is the smaller firewire connection instead of the larger one found on external firewire devices. Good luck.
Steve

Time code slowly drifting when printing to tape

I have noticed that my time code is drifting a bit when I print to tape, it gets more noticeable the longer the video i need to print is. Why would it do that?

Well, both should be set to drop frame then....by default. Go to the SEQUENCE>SETTINGS and see if DROP FRAME is checked next to the STARTING TC in the TIMELINE OPTIONS tab.
Shane

Drop-Frame v. Non-Drop Frame and Edit to Tape

System Configuration: G5 Dual 2.0, QT v7.0.4, FCP v5.0.4, OS X v10.4.6, KonaLH, Keyspan USA-28x USB-->Serial Adapter
Problem: When working with a drop-frame sequence, and editing to tape, the program is edited to the tape with an offset of 3 seconds and 18 frames.
Reproducible: Yes.
Steps to Reproduce:
1. Create a drop-frame sequence.
2. Edit the sequence in step 1.
3. Perform an edit to tape with the sequence edited in step 2.
What should happen: The sequence should be edited to tape at the time it occurs in the timeline.
What does happen: The sequence is edited to the tape 3 seconds and 18 frames after it should be!
Other observations: 3 seconds and 18 frames is exactly how much time is not in an hour of drop-frame time when compared to non-drop frame time. If you drop two (2) frames in every minute that does not end in zero, the math works out to 2*54=108 dropped frames in an hour. For the sake of simple mathematics, lets say there are 30 frames in a second. So 108/30= 3 with a remainder of 18, or 3 seconds and 18 frames.
It's as if FCP is getting confused about drop and non-drop timecode when the sequence is drop-frame. If anyone can offer any insights, confirmation, or resolutions for what I am seeing, it would be appreciated.
Thanks for reading!

This may be related to a "bug" or issue that has been around since FCP1. When FCP is using deck control over firewire, The timecode display will default to DF, even if the tape is NDF. Look closely at the timecode dispays in the edit to tape window. If you see a semicolon before the frames place, FCP is seeing the tape TC as DF. Play the tape until you see the TC display change to NDF, then re-set your in point. This has worked for me in the past.
Hope this helps.

Loosing audio when printing to tape.

I used FCE to edit my DV-material. It wasn't ever a problem.
I bought a HD-camera (Sony HDR-HC3) and edited a 40 minutes film from about 4 hours footage with FCE HD-3.0.
Editing is no problem. Making a DVD is O.K. But printing to tape is horrible. I loose parts of the music-tracks. Sometimes dropped frames etc. (And it takes a lot of time: about 4 hours to render!).
Many times I tried to print to tape. The problems exist every time in different places (except one place where the music always disappears).
I don't know how to loose this problem. I always mixdown audio, remove prefs etc. but till now no positiv result.
What to do?
G5-2x1.8 Mac OS X (10.3.9)

Hi(Bonjour)!
If there is a song bought on iTune Music Store, you can't use this track.
Did you render an audio mixdown before export ?
Try a test version with just one minute of movie. (set in and out point in timeline and do the print to tape operation).
Try a print to tape from a cold start mac.
Drag your playhead around your sequence before printing (it's seem that this process load the cahe memory, at least in my own experience)
If the problem is still there, you can also do an audio track mix quicktime conversion export (aiff 16 bit) from your sequence, import it into a new sequence, open your previous edited one in editor (option clik), do uncheck audio A1 and A2 target, and drag the video content on V1 in the new sequence. Drag your exported audio on A1 A2.
Do a check for the synch of your movie.
Do not forget to do an audio mixdown before print to tape.
Does your hard drive is fragmented or full at more than 80% level?
Michel Boissonneault

Audio recorded from lavalier mic is not audible when printing to tape

hello!
i am very confused : ( i have an edited work with some audio recorded directly from the built-in camera mic, and most of the audio from a lavalier (lapel) mic. all the audio plays fine from the timeline, and from the "print to video" play back option, when the video playback is set to "none" or "preview"; however, when it is set to ntsc (which i believe i need in order to print it back onto a mini DV tape to submit it) only the audio recorded with the built-in camera mic is clear and audible. the other recorded sounds from the lav mic are very quiet (or silent) and have static noises.
i have exported the timeline and burnt it to a dvd, and all the audio works fine. but i can not seem to print it to a tape without losing most of the audio.
i have tried all different combinations of settings (audio to built in audio, or to firewire), etc etc and nothing seems to fix this problem.
any suggestions would be GREATLY appreciated! thanks : )

You might try highlighting all the audio tracks
then go to the MODIFY drop down - AUDIO - PAN CENTER.
This should make sure all your audio tracks are audible.
Also, I'm not in front of the interface right now,
but if you go to FINAL CUT PRO drop down - AUDIO / VIDEO
SETTINGS, somewhere in there (perhaps in a tab or at the bottom) is a drop down for PRINT TO VIDEO, and there are
some settings there. Make sure it is including all your
audio channels and not set up in some funky way.
Message was edited by: brvideo

Exported pdf from indesign drops punctuation when printed from adobe reader

The pdf prints fine when printed from acrobat pro, but depending on the export pdf settings from indesign, it will drop most numbers and punctuation when printed from adobe reader.

Is Adobe Reader installed on the same computer Adobe Acrobat is?

Compressor 4 drops frames when converting 25fps image sequences

I am using Compressor 4 to batch convert 30fps and 25fps 1080 tiff image sequences to Uncompressed 10bit 422.
I have created custom presets for both 30fps and 25fps.
The 30fps conversions are fine.
But the 25fps conversions have missing or dropped frames and the resulting clip is too short. For example a 106 frame image sequence becomes 88 frames when converted to Uncompressed 10bit 422 QT. (which suspiciously similar to the 83.33% difference between 25 & 30 fps)
I have double checked my setting and can not find a problem (see grab)
Any suggestions much appreciated.

Update: I have found a work around for this problem, but it is not pretty!
By using the 30fps setting even for 25fps sequences, every frame gets included in the resulting QuickTime. But it plays at the wrong frame rate, so I then use Cinema Tools to change the frame rate to 25fps. Then everything is fine.
As Compressor 4 has been around for while, I can't believe this hasn't come up before!

Drop frames when printing to tape !

Similar Messages

Maybe you are looking for