Ds5.1 on Solaris 8 core install and SNMP

On a Solaris 8 core installation with the Directory Server 5.1,
everything works okay, except SNMP activation from the Administration Server which sends the following error
message :
"Setup select/poll problem : Invalid argument"
SNMP master agent refuses to start.
This works very well on a Solaris 8 full install, so the question
is :
What Solaris 8 packages are required to handle SNMP properly
in this context ?
Thank you very much for your help.
JCT

when i access
http://localhost/portal
A serious error has occured in the Desktop. This may have been caused by a mis-configuration on the server.
Please report this problem to your administrator.
Return to front page

Similar Messages

Solaris 10 new install and new (?) hard disks

Ok, so I started a solaris 10 install (5/08) on a sparc enterprise 3000 server. I first did the install on 2 brand new 10.7k rpm seagate cheetahs and I was able to install, copy layout to the target disk, configure Raid 1 mirror, was able to boot from the mirror, so on and so on, basically everything ran accordingly. Then I was told that there was a batch of brand new 15k rpm cheetahs and that I should use those. As I rebooted with the new drives, I got the "magic label" warning, so basically I re-labeled them. I ran install and everything installed as before, BUT when I went to SMC to copy the disk layout to the target drive, the only drive present is the target drive (c0t1d0). The drive c0t0d0 does not show. Format does show both drives. Now, if I reboot without drive c0t1d0 and immediately go to SMC/Disks, the drive c0t0d0 is there. What is causing that behavior? Do the drives already have labels and partition info that need to be cleared or redone? I have already tried to re-label and re-partition c0t1d0 identically to c0t0d0 and that does not seem to have an effect. I tried running fdisk /dev/rdsk/c0t1d0 and I get the " cannot stat device /dev/rdsk/c0t1d0" message. Is there a way to completely wipe out the entire drive c0t1d0 through solaris? Any suggestions? Thanx in advance.
Erickc

ok, so I was able to copy the c0t0d0 layout to c0t1d0 and that went trough. I verified through format>partition that both drives had identical partition information. I created metadb's to both drives in the specific slices and that was ok. Now here's what I get when I try to create a mirror...
metainit -f d1 1 1 c0t0d0s0
d1: concat/stripe is setup
metainit d2 1 1 c0t1d0s0
metainit: c0t1d0s0: overlaps with c0t0d0s0 which is mounted as "/"
On my first install I was able to create the mirror without a problem. What would be the cause?
Thanx in advance for any suggestions.

Solaris 10 JET install and ZFS

Hi - so following on from Solaris Volume Manager or Hardware RAID? - I'm trying to get my client templates switched to ZFS but it's failing with:
sudo ./make_client -f build1.zfs
Gathering network information..
Client: xxx.14.80.196 (xxx.14.80.0/255.255.252.0)
Server: xxx.14.80.199 (xxx.14.80.0/255.255.252.0, SunOS)
Solaris: client_prevalidate
Clean up /etc/ethers
Solaris: client_build
Creating sysidcfg
WARNING: no base_config_sysidcfg_timeserver specified using JumpStart server
Creating profile
Adding base_config specifics to client configuration
Adding zones specifics to client configuration
ZONES: Using JumpStart server @ xxx.14.80.199 for zones
Adding sbd specifics to client configuration
SBD: Setting Secure By Default to limited_net
Adding jass specifics to client configuration
Solaris: Configuring JumpStart boot for build1.zfs
Solaris: Configure bootparams build
Starting SMF services for JumpStart
Adding Ethernet number for build1 to /etc/ethers
cleaning up preexisting install client "build1"
removing build1 from bootparams
removing /tftpboot/inetboot.SUN4V.Solaris_10-1
svcprop: Pattern 'network/tftp/udp6:default/:properties/restarter/state' doesn't match any entities
enabling network/tftp/udp6 service
svcadm: Pattern 'network/tftp/udp6' doesn't match any instances
updating /etc/bootparams
copying boot file to /tftpboot/inetboot.SUN4V.Solaris_10-1
Force bootparams terminal type
-Restart bootparamd
Running '/opt/SUNWjet/bin/check_client build1.zfs'
Client: xxx.14.80.196 (xxx.14.80.0/255.255.252.0)
Server: xxx.14.80.199 (xxx.14.80.0/255.255.252.0, SunOS)
Checking product base_config/solaris
Checking product custom
Checking product zones
Product sbd does not support 'check_client'
Checking product jass
Checking product zfs
WARNING: ZFS: ZFS module selected, but not configured to to anything.
Check of client build1.zfs
-> Passed....
So what is "WARNING: ZFS: ZFS module selected, but not configured to to anything." referring to? I've amended my template and commented out all references to UFS so I now have this:
base_config_profile_zfs_disk="slot0.s0 slot1.s0"
base_config_profile_zfs_pool="rpool"
base_config_profile_zfs_be="BE1"
base_config_profile_zfs_size="auto"
base_config_profile_zfs_swap="65536"
base_config_profile_zfs_dump="auto"
base_config_profile_zfs_compress=""
base_config_profile_zfs_var="65536"
I see there is a zfs.conf file in /opt/SUNWjet/Products/zfs/zfs.conf do I need to edit that as well?
Thanks - J.

Hi Julian,
You MUST create /var as part of the installation in base_config, as stuff gets put there really early during the install.
The ZFS module allows you to create additional filesystems/volumes in the rpool, but does not let you modify the properties of existing datasets/volumes.
So,
you still need
base_config_profile_zfs_var="yes" if you want a /var dataset.
/export and /export/home are created by default as part of the installation. You can't modify that as part of the install.
For your zones dataset, seems to be fine and as expected, however, the zfs_rpool_filesys needs to list ALL the filesystems you want to create. It should read zfs_rpool_filesys="logs zones". This makes JET look for variables of the form zfs_rpool_filesys_logs and zfs_rpool_filesys_zones. (The last variable is always picked up, in your case the zones entry. Remember, the template is a simple name=value set of variables. If you repeat the "name" part, it simply overwrites the value.)
So you really want:
zfs_rpool_filesys="logs zones"
zfs_rpool_filesys_logs="mountpoint=/logs quota=32g"
zfs_rpool_filesys_zones="mountpoint=/zones quota=200g reservation=200g"
(incidentally, you don't need to put zfs_pools="rpool" as JET assumes this automatically.)
So, if you want to alter the properties of /var and /export, the syntax you used would work, if the module was set up to allow you to do that. (It does not currently do it, but I may update it in the future to allow it).
(Send me a direct e-mail and I can send you an updated script which should then work as expected, check my profile and you should be able to guess my e-mail address)
Alternatively, I'd suggest writing a simple script and stick it into the /opt/SUNWjet/Clients/<clientname> directory with the following lines in them:
varexportquotas:
#!/bin/sh
zfs set quota=24g rpool/export
zfs set quota=24g rpool/ROOT/10/var
and then running it in custom_scripts_1="varexportquotas"
(Or you could simply type the above commands the first time you log in after the build. :-) )
Mike
Edited by: mramcha on Jul 23, 2012 1:39 PM
Edited by: mramcha on Jul 23, 2012 1:45 PM

Solaris 10 x86 install and X Windows

Greetings,
I am having trouble getting the X server to come up on a new install of S10 on an x86 platform. I have run the kdmconfig utility and it correctly detects the hardware for the Xsun server. I tried to use the instructions for Xorg but Xorg does not appear to have been installed.
Any ideas as to what I should try next?
Thanks
TC

it was suggested that one should try to change the resolution.
Question: is there any way to change the resolution of the
Sun X server while it is running ? If not, what config file controls resolution ?
steve

Solaris 10 x86 install and Networking

Greetings,
I have finally gotten S10 insalled on a Win-Tel box and it appears to be working, for the most part. I am currently working on getting the box integrated into our company network and need some direction.
First, is there a good tutorial on configuring a network connection on Solaris 10? I need something that starts at ground zero and walks me through the process. I am UNIX literate but it's been a while since I have had to admin a system.
So what I need to do is:
a. get the Lan card recognized and configured under S10
b. Get the DHCP client working so I can obtain an IP address from our internal DHCP server (actually I think it's running on a switch).
c. Get Samba up and running so I can share files with a Windows machine.
Any pointers to information on how to do this would be greatly appreciated.
Cheers
TC

Well, if you don't think the online Documentation helpful, then the better way is reading step-by-step instructions from a book. Get to local bookstore, i.e Barne&Nobles or Border or any big local bookstore, there should be pretty good book for Unix Administrator (Solaris version).
If you have time and think you can memorize then, read on the spot; otherwise, buy the book for future reference.
If that's not what you had in mind, then this link of free online book might help : http://www.oreilly.com/catalog/solaris8/chapter/ch04.html
Normally, oreilly online bookstore offers free books to accredited universities, colleges, and organizations. However, if that option isn't for you, it might even offer free sample chapters that might just suit your needs.
hoep it helps.
-van.

Core install

First Question:
I've installed Solaris 8 for IA using the 1/01 media doing the core install, and adding some of the SUNW* packages that I thought might be necessary using the Web installer (though I was not using the windows GUI to do it, but rather the basic command line options). I don't have any CDE software installed.
While I can make do without (I have other Solaris machines with more robust installs that I can refer to) I'm not getting the man pages to work even though I have both SUNWman and SUNWdoc (which is described as: utilities and fonts for development, display, and production of documentation such as manual pages (nroff/troff)).
When I do a
% man userdel
as just one example, I get:
Reformatting page. Please Wait...Invalid SGML. File cannot be formatted
sys(cd /usr/share/man; /usr/lib/sgml/sgml2roff /usr/share/man/sman1m/userdel.1m > /tmp/sman_456) fail!
aborted (sorry)
So my first question is, does anyone know of an additional package that needs to be installed? I have all listed dependencies installed for both SUNWdoc and SUNWman
Second Question:
Another thing I noticed is that some commands that I'd like are not on the system. For example,
% vipw
isn't on the system. Again, I can make do, because I have "useradd"/"usermod"/"userdel" available (and maybe that's all I really need). That's just an example.
So my second question is, is there a way to go about finding what package has, for example, "vipw"?
=== Al

Need the same information too, I have this list so fae but it is hanging talking to Sun
SUNWcsmauth
SUNWcctpx
SUNWccinv
SUNWccfwctrl
SUNWupdatemgru
SUNWccccr
SUNWpprou
SUNWccsign
SUNWccccfg
SUNWdc
SUNWupdatemgrr
SUNWppro-plugin-sunos-base
SUNWppror
SUNWswupcl
SUNWccfw
SUNWccccrr
SUNWbreg
SUNWswupclr
SUNWscnsom
SUNWscnsomr
SUNWswupclr
SUNWbrg
SUNWcacaort
SUNWscn-base
SUNWscn-base-r
SUNWscnprm
SUNWscnprmr
SUNWsensor
SUNWsensorr
SUNWjdmk-base

Fresh install and update patch problems 119060-17 , 122213-10 , 122912-02

Just yesterday, i installed a fresh Solaris 10 x86 onto some pc hardware. After getting solaris installed and issues with my network card, i downloaded and installed the free version of the update manager 1.0.x. Next, i proceeded to update all the general patches for the solaris 10 system. I started with the command 'pprosvc -i' from a terminal. It then proceeded to download and validate a bunch of patches successfully until it hit the following 3 patches:
119060-17 ---- X11 6.6.2_x86: Xsun patch
122213-10 ---- GNOME 2.6.0_x86: GNOME Desktop Patch
122912-02 ---- SunOS 5.10_x86: Apache 1.3 Patch
All 3 failed some kind of validation and then crashed the pprosvc program, at which point it exited with the following error:
122912-02 cannot be validated
119060-17 cannot be validated
122912-02 cannot be validated
Unexpected Failure: java.lang.Throwable: ERROR: Failed to validate the digital signature(s).
I also tried to use the GUI Update Manager to update, hoping the problem was isolated to pprosvc, but that problem was also in the GUI with a similar error message:
Error occurred...The detailed error message is: Unexpected Failure: java.lang.Throwable: ERROR: Failed to validate the digitial signature(s)
Anyone know why Sun's update patch process is so troublesome?
Getting Tired of Solaris Updates...
I should mention that this is the free solaris 10 x86 install and i don't have a service contract with Sun. If this problem persists, i don't think i'll get one, as i see only further problems after buying one.
tired and confused

Hi,
There is an issue with this that is currently being investigated. There is another thread that may shed some light on what is happening here;
http://forum.sun.com/jive/forum.jspa?forumID=316
Thread title is : Sun UC, Digitally Signed Patches Using New Verisign Certificates
In the short-term please ensure that the patch mentioned in it is installed.
To quote part of mentioned thread above:
"Once the Sun Update Connection client software is upgraded with patch 121118-06 (SPARC) or 121119-06 (x86/x64) or later revisions normal behavior will resume. "
If this fails to resolve your problem, would you be kind enough to post the output of the following command for analysis please;
# showrev -p | egrep -e '121454|121119|120336|121082|121564|122232|119789'
Sincerely,
Moderator.
Message was edited by:
ForumModerator

Fresh solaris 10 x86 install patch update problems 119060-17 ...

Just yesterday, i installed a fresh Solaris 10 x86 onto some pc hardware. After getting solaris installed and issues with my network card, i downloaded and installed the free version of the update manager 1.0.x. Next, i proceeded to update all the general patches for the solaris 10 system. I started with the command 'pprosvc -i' from a terminal. It then proceeded to download and validate a bunch of patches successfully until it hit the following 3 patches:
119060-17 ---- X11 6.6.2_x86: Xsun patch
122213-10 ---- GNOME 2.6.0_x86: GNOME Desktop Patch
122912-02 ---- SunOS 5.10_x86: Apache 1.3 Patch
All 3 failed some kind of validation and then crashed the pprosvc program, at which point it exited with the following error:
122912-02 cannot be validated
119060-17 cannot be validated
122912-02 cannot be validated
Unexpected Failure: java.lang.Throwable: ERROR: Failed to validate the digital signature(s).
I also tried to use the GUI Update Manager to update, hoping the problem was isolated to pprosvc, but that problem was also in the GUI with a similar error message:
Error occurred...The detailed error message is: Unexpected Failure: java.lang.Throwable: ERROR: Failed to validate the digitial signature(s)
Anyone know why Sun's update patch process is so troublesome?
Getting Tired of Solaris Updates...
I should mention that this is the free solaris 10 x86 install and i don't have a service contract with Sun. If this problem persists, i don't think i'll get one, as i see only further problems after buying one.
tired and confused

Hi,
There is an issue with this that is currently being investigated. There is another thread that may shed some light on what is happening here;
http://forum.sun.com/jive/forum.jspa?forumID=316
Thread title is : Sun UC, Digitally Signed Patches Using New Verisign Certificates
In the short-term please ensure that the patch mentioned in it is installed.
To quote part of mentioned thread above:
"Once the Sun Update Connection client software is upgraded with patch 121118-06 (SPARC) or 121119-06 (x86/x64) or later revisions normal behavior will resume. "
If this fails to resolve your problem, would you be kind enough to post the output of the following command for analysis please;
# showrev -p | egrep -e '121454|121119|120336|121082|121564|122232|119789'
Sincerely,
Moderator.
Message was edited by:
ForumModerator

I am running Photoshop CC 2014 on Windows 8.1 with an AMD quad core processor and AMD E1-2100 APU with AMD Radeon HD 8210 Graphics Card. I have installed the latest driver version 13.152.0.0. When I activate puppet warp, the mesh appears over the image an

I am running Photoshop CC 2014 on Windows 8.1 with an AMD quad core processor and AMD E1-2100 APU with AMD Radeon HD 8210 Graphics Card. I have installed the latest driver version 13.152.0.0. When I activate puppet warp, the mesh appears over the image and I can place the first pin. However, when I go to add the second pin, Photoshop crashes. I have tried with on a new, blank file, with just a few lines on it, but, as soon as I place the first pin, the image disappears, and then, as soon as I click anywhere else in the image, Photoshop crashes. I have followed all the online advice about settings under the Preferences/Performance interface, but nothing fixes the problem. Can anyone please help?

BOILERPLATE TEXT:
If you give complete and detailed information about your setup and the issue at hand, such as your platform (Mac or Win), exact versions of your OS, of Photoshop and of Bridge, machine specs, such as total installed RAM, scratch file HDs, video card specs, what troubleshooting steps you have taken so far, what error message(s) you receive, if having issues opening raw files also the exact camera make and model that generated them, etc., someone may be able to help you.
A screen shot could be very helpful too.
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks!

Solaris 10 with zfs root install and VMWare-How to grow disk?

I have a Solaris 10 instance installed on an ESX host. During the install, I selected a 20gig disk. Now, I would like to grow the disk from 20GB to 25GB, I made the change on VMWare but now the issue seems to be Solaris. I haven't seen anything on how to grow the FS in Solaris. Someone mentioned using fdisk to manually change the number of cylinders but that seems awkward. I am using a zfs root install too.
bash-3.00# fdisk /dev/rdsk/c1t0d0s0
Total disk size is 3263 cylinders
Cylinder size is 16065 (512 byte) blocks
Cylinders
Partition Status Type Start End Length %
========= ====== ============ ===== === ====== ===
1 Active Solaris2 1 2609 2609 80
This shows the expanded number of cylinders. but a format command does not.
bash-3.00# format
Searching for disks...done
AVAILABLE DISK SELECTIONS:
0. c1t0d0 <DEFAULT cyl 2607 alt 2 hd 255 sec 63>
/pci@0,0/pci1000,30@10/sd@0,0
Specify disk (enter its number):
Any ideas?
Thanks.

That's the MBR label on the disk. That's easy to modify with fdisk.
Inside the Solaris partition is another (VTOC) label. That one is harder to modify. It's what you see when you run 'format' -> 'print' -> 'partition' or 'prtvtoc'.
To resize it, the only method I'm aware of is to record the slices somewhere, then destroy the label or run 'format -e' and create a new label for the autodetect device. Once you have the new label in place, you can recreate the old slices. All the data on the disk should be stable.
Then you can make use of the space on the disk for new slices, for enlarging the last slice, or if you have a VM of some sort managing the disk.
Darren

I have an iMac 5.1 ,2ghz core 2duo with 1gb 667 MHz ddr2 SS ram running osx 10.6.8. How much tota ram can I install and will it be enough to run lion and/or mountain lion?

I have a iMac 5.1 running osx 10.6.8 , core 2duo, and 1ghz 667mhz DDR sdram. How much ram can be added and will it run lion/mountain lion? Thanks.

As an additional thought: I had this same model iMac and although you can install 4 GB RAM, it will only address just over 3 GB. Since Lion is somewhat of a memory hog, you really will not be very happy with the performance using anything less than 4 GB - and even 4 GB is a bit of a minimum; fine for basic needs, but any photo or video editing will require more than that.

How install Solaris 2.5.1 and Windows Together

Hi, We�ve a registered copy of Solaris 2.5.1 and we can�t install solaris and windows in the same Hard disk.
I�ve been trying since two weeks. I can�t found a document that help me with this task.
Please, help me with the directions to do that or try to indicate me an internet link to read it.
Thanks a lot.

OK, this is that I did.
1. With solaris 2.5.1. boot disk install solaris from CDROM
2. I do the partition in hard disk, the disk has 3 GB, and make a 940 MB partition for solaris and the rest for Windows
3. I install solaris in stangalong mode
4. When I finished solaris installation, it ask me wich partition are going to use to boot de machine.
5. I format a WINDOWS disk partition to install it.
6. I transfered the system to the windows partition
7. Reboot the machine and the solaris still ask me by wich O/S are going to use to boot.
8. Then, install Windows 95 B version, and when rebbot the machine, the boot manager of salaris dissaper.
9. With FDISK of windows and put the second partition (solaris) as active, and nothing happens.
Note: I`m using the solaris partition as second one, i mean that the main partition is Windows (is exactly that I did have it).

Hi i have a macbook its osx 10.4.11 core duel and i think its tiger already installed but it needs updating what do i do thanks

hi i have a macbook its osx 10.4.11 core duel and i think its tiger already installed but it needs updating what do i do thanks

Hi Paul
The current version of OS X is Snow Leopard (OS X 10.6) and you should be able to order an installation disk for your MacBook from the on line Apple Store.
Soon, a newer version of OS X (called Lion) is being released, but I don't think that it will run on a Core Duo because that particular processor is 32 bit only.
Bob

I have recently purchased a refubished imac 3.06 ghz intel core 2 duo and I'm trying to install logic 7.2 on this machine. I get half way through the content install and it crash's . I have it installed on an older Imac and it works fine. Is there any e

I have recently purchased a refubished imac 3.06 ghz intel core 2 duo and I'm trying to install logic 7.2 on this machine. I get half way through the content install and it crash's . I have it installed on an older Imac and it works fine. Is there anybody out there that can help me figuire outhow to make this work?

See:
Mac Maintenance Quick Assist,
Mac OS X speed FAQ,
Speeding up Macs,
Macintosh OS X Routine Maintenance,
Essential Mac Maintenance: Get set up,
Essential Mac Maintenance: Rev up your routines,
Maintaining OS X,
Five Mac maintenance myths, and
Myths of required versus not required maintenance for Mac OS X for information.

How to Install and config Discover9.0.2 on Solaris?

I am finding the doc about HOW to install and config Discover9.0.2 on Solaris where Application 11i has been installed!
It's quite uegent.Hope you can help me.If possible,pls directly mail the docs to me:[email protected]
Thanks!

Hi,
Installaing Discover is quite easy but you need to configure to the database and apps also for which you need to create a repostory. So keep you database login and a seperate tablespace ready and start discover from oracle_discover_home/bin you will find options there for configuring repostory there.
kamalesh jk

Ds5.1 on Solaris 8 core install and SNMP

Similar Messages

Maybe you are looking for