DSL bridged works on ethernet but not wireless.

I have been trying to solve my NAT problems with Xbox live. My first attempt is to bridge my Motorola/Netopia 2210 DSL modem, ISP is Bellsouth/ATT.
I successfully set the 2210 to bridge mode. I set the router (wrt54gl) to PPPoE and entered my bellsouth login. When I am hardwired into port 1 of the router I can connect to the Internet. When I unplug the ethernet cable and disable local connection and enable wireless, I lose my full connection and get a local only connection.
I have power cycles all devises in order modem, router, laptop but that does not seem to help. If I enable PPPoE on the 2210 and DHCP on the router I get full access both wireless and wired.
any ideas?

When you set the modem in the bridge mode and router as in PPPOE mode, Are you able to see the your wireless network?
If yes, then follow the below mentioned settings.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
On the set-up tab change the MTU Size to 1365 and click Save Settings...
Click on "Administration" tab and disable the option UPnP and click Save Settings...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 53 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box, click Save Settings once done...
2) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
3)Click on the Status tab and take note of DNS1 and DNS2 Addresses...
4) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox
IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
5) Also assign the DNS Addresses on the Xbox
Use DNS1 and DNS2 Addresses you took note off of the router status tab as Primary DNS & Secondary DNS for the xbox...
6) Turn off your modem, router, and Xbox...Wait for a minute...
7) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...
IP Address: 192.168.X.[last part of ip in your device] e.g. if static ip given to the device was 192.168.X.10 get the last part and put that to the empty box.
This should fix the issue for you.

Similar Messages

Works on ethernet, but not wireless

I'm configuring my AirPort Extreme after some cable modem problems and now the wireless won't work. The AirPort utility says it doesn't have a proper IP address, but I can get internet through an ethernet cable from the AE box, so that doesn't seem right. The amber light is flashing. I've tried resetting and pulling the power, but no luck. Any ideas?
Thanks

Eh? PPPoE connection to the cable modem from the AE? Unless I missed something that is never going to work.
1. Cable modems do not use PPPoE. It's equivalent I guess would be DOCSIS.
2. The Cable modem will have an Ethernet output.
The only way what you are describing might would would be if the AEBS was connected direcly to the phone point, in that case use PPPoE, or the device it is connected to, some kind of ADSL modem, not Cable modem, is passing through PPPoE to the AEBS.
If the OP is connnecting to a cable modem, via Ethernet, turn off PPPoE on the AEBS and switch to Ethernet.
If there is nothing between the two devices, then enable DHCP so that the AEBS picks up the WAN IP and turn on one of the methods of connection sharing, enabling DHCP and NAT for devices connecting behind it via Ethernet or Wireless.

I can home share to Apple TV via ethernet but not wireless. Please help!!

This has been driving me mad for a week now. I have an acer Laptop using windows vista. When I connect the Ethernet cable to my rout and laptop, home sharing works fine. But as soon as I disconnect and go wireless, Apple TV cannot find my library. My partner has a HP laptop that operates on windows xp. That works fine. can anyone help and give me a step by step guide with what to do? I've checked every apple forum on the matter and nothing seems to work. I figure it's got something to do with my wireless Internet settings. It can't be the router if my partners library shares ok, right?? I've uninstalled macafee and even turned my windows firewall off. But surely these weren't problems in the first place if Ethernet connection works?!? Am not very tech savvy, so any simple things to check would be SO appreciated.

Homesharing should work over ethernet too, ask your network provider about homesharing, it may be that the university doesn't allow it.

Airport Express only works through Ethernet and not wireless

Hi there,
As it states in the header - Airport Express works when I connect it either directly to my iMac or through my Cable modem using an ethernet cable. Unfortunately, as soon as I unplug the ethernet and try to use it wirelessly, it disappears from the AirPort Utility view and I can no longer connect. Strangely the green light stays on solid, no flashing.
I'm no wireless connectivity expert so am sure it's something basic I've missed. Would be most grateful of any pointers.
Thanks

For the short term ...
Either connect to the AX's wireless network or connect directly, using an Ethernet cable, to the Ethernet port of the AX, and then using the AirPort Utility in "Manual Setup" mode, make the following changes:
AirPort > Base Station
o Base Station Name: <rename or leave default>
o Base Station Password: <enter desired password>
o Verify Password: <re-enter desired password>
o Remember this password in my keychain: (optional)
o Set time automatically: (unchecked)
AirPort > Wireless
o Wireless Mode: Join a wireless network
o Network Name: <existing BT HomeHub's wireless network>
o Wireless Security: <select the encryption type of the existing wireless network>
o Wireless Password: <enter the existing wireless network password>
o Verify Password: <re-enter the existing wireless network password>
Music
o Enable AirTunes (checked)
o iTunes Speaker Name: <enter desired speaker name>
o iTunes Speaker Password: (optional)
o Verify Password: (optional)
o Click Update to write the new settings to the AX
In iTunes:
iTunes > Preferences... > Advanced > General
o Look for remote speakers connected with AirTunes (checked)
For the longer term, since the BT HomeHub is not WDS-compatible with the AX, the AX would need to be connected directly, via Ethernet, to the BT and then re-configured as a bridge to allow the BT to continue to provide NAT & DHCP services for the entire network.

IChat works with ethernet, but not with wifi

I've been having problems signing into iChat over my wifi connection for a long time. It will say connecting but a second later it will tell me that the connection to AIM was lost. When i sign in and my computer is connected to the internet with a cable, it works fine. I can sign in using AIM for mac over the wifi no problem, it is only with iChat.
Any help will be appreciated for i do not like the AIM for mac.
Thanks

I will assume you're talking about video iChat connections.
You may want to check the effective Internet bandwidth while hooked-up to the Wifi. I suggest you try a speed test at one of the sites at speakeasy.net. Pick the one closest to your location. If you're getting a speed test over Wifi at about 1Mbps per second down, then I think you have a Wifi connection problem. Wifi speed is sensitive to distance and walls.
Also take a look at your port connection on iChat. Look in iChat preferences and server settings. It should say port 443 not 5190.
Lastly in Systems Preferences, set your Quicktime streaming speed to 1.5 not automatic.
Then restart iChatAV.
... just noticed you have a Netgear router. I have had problems with that router and switched to Linksys WERT54g v4 with a dd-wrt driver. Check to see you are using UPnP and do not open any ports on your router or the Mac firewall.

I have a MacBook Pro and all of a sudden I cannot get wireless internet connectivity to my router or any other router, I get connectivity through the ethernet port but not wireless. This was working well till this morning

I have a MacBook Pro and all of a sudden I cannot get wireless internet connectivity to my router or any other router, I get connectivity through the ethernet port but not wireless. This was working well till this morning

BXB1905 wrote:
I tried the Apple diagnostics it did not work.
What do you mean it did not work! What were the results of the diagnostic tests?
Have you contacted your ISP to determine if the problem is on their end?
Have you changed your router channel? Sometimes this resolves wireless problems.
Your profile confirms you are using Lion. Check out the following:
Troubleshooting Wi-Fi issues in OS X Lion and Mac OS X v10.6
Configuring 802.1X in Mac OS X Lion and Later

Time Machine works on Ethernet connection but not wireless

Hi,
This weekend I setup time machine to work with a NAS drive connected to my wireless router. If I connect my macbook to the router directly via an ethernet cable, and start a backup, it works fine. If I however try to start a backup when only on wireless it always fails. Here's what messages I'm getting:
Starting standard backup
Attempting to mount network destination using URL: afp://;AUTH=No%20User%20Authent@Backup%20to%20Iomega-0cd217.afpovertcp.tcp.local/backups
NetAuthConnectToServerSync failed with error: 64 for url: afp://;AUTH=No%20User%20Authent@Backup%20to%20Iomega-0cd217.afpovertcp.tcp.local/backups
Attempting to mount network destination using URL: afp://;AUTH=No%20User%[email protected]/backups
Mounted network destination using URL: afp://;AUTH=No%20User%[email protected]/backups
Warning: Destination /Volumes/backups does not support TM Lock Stealing
Warning: Destination /Volumes/backups does not support Server Reply Cache
QUICKCHECK ONLY; FILESYSTEM CLEAN
Disk image /Volumes/backups/Garys-MacBook-Pro_xxxxxxxxxxxx.sparsebundle mounted at: /Volumes/MAC Backups
Backing up to: /Volumes/MAC Backups/Backups.backupdb
Stopping backupd to allow ejection of backup destination disk!
Error: (5) getxattr for key:com.apple.backupd.SnapshotState path:/Volumes/MAC Backups/Backups.backupdb/Gary's MacBook Pro/2011-01-15-042811
Error: (5) getxattr for key:com.apple.backupd.SnapshotContainer path:/Volumes/MAC Backups/Backups.backupdb/Gary's MacBook Pro/2011-01-15-042811
Error: (5) getxattr for key:com.apple.backupd.SnapshotState path:/Volumes/MAC Backups/Backups.backupdb/Gary's MacBook Pro/2011-01-15-171318.inProgress
Error: (5) getxattr for key:com.apple.backupd.SnapshotContainer path:/Volumes/MAC Backups/Backups.backupdb/Gary’s MacBook Pro/2011-01-15-171318.inProgress
Error: (5) getxattr for key:com.apple.backupd.SnapshotState path:/Volumes/MAC Backups/Backups.backupdb/Gary’s MacBook Pro/2011-01-15-042811
Error: (5) getxattr for key:com.apple.backupd.SnapshotContainer path:/Volumes/MAC Backups/Backups.backupdb/Gary’s MacBook Pro/2011-01-15-042811
Error: (5) getxattr for key:com.apple.backupd.SnapshotState path:/Volumes/MAC Backups/Backups.backupdb/Gary’s MacBook Pro/2011-01-15-171318.inProgress
Error: (5) getxattr for key:com.apple.backupd.SnapshotContainer path:/Volumes/MAC Backups/Backups.backupdb/Gary’s MacBook Pro/2011-01-15-171318.inProgress
Backup canceled.
[SnapshotUtilities mountPointForVolumeRef] FSGetVolumeInfo returned: -35
Failed to eject volume (null) (FSVolumeRefNum: -179; status: -35; dissenting pid: -1)
[SnapshotUtilities mountPointForVolumeRef] FSGetVolumeInfo returned: -35
Failed to eject volume (null) (FSVolumeRefNum: -178; status: -35; dissenting pid: -1)
I've x'ed out the mac address from the sparsebundle name. Any help would be much appreciated as I can't understand why it's working when connected but not when on wireless.
Thanks!

GT777 wrote:
Hi,
Hi, and welcome to the forums.
This weekend I setup time machine to work with a NAS drive connected to my wireless router.
Time Machine doesn't work well, if at all, with many NASs. See the pink box in #2 of [Time Machine - Frequently Asked Questions|http://web.me.com/pondini/Time_Machine/FAQ.html] (or use the link in *User Tips* at the top of this forum).
There are several threads in the Snow Leopard > Time Machine forum with what appear to be similar problems with Iomega NASs.
If I connect my macbook to the router directly via an ethernet cable, and start a backup, it works fine. If I however try to start a backup when only on wireless it always fails.
An indication of a bad wireless connection or interference, but could also be the setup of the NAS or compatibility with the way the router works in wireless mode.
Mounted network destination using URL: afp://;AUTH=No%20User%[email protected]/backups
After an initial failure, it did connect.
Warning: Destination /Volumes/backups does not support TM Lock Stealing
Warning: Destination /Volumes/backups does not support Server Reply Cache
You've posted in the Leopard forum, and didn't specify what version of OSX you're on. But those messages usually indicate that your NAS is not fully compatible with the Time Machine requirements on Snow Leopard.
Error: (5) getxattr for key:com.apple.backupd.SnapshotState path:/Volumes/MAC Backups/Backups.backupdb/Gary's MacBook Pro/2011-01-15-042811
Those are errors reading from the backups; specifically, getting extended attributes from the backups on your NAS (a "snapshot" is Time Machine's name for a backup folder).
First, contact the maker of the NAS for updated software/firmware compatible with Snow Leopard.
That might fix the problem. If not, all we can tell you is, it may be some problem with the setup of the NAS, and/or compatibility with the wireless function of your router. See the maker's instructions/Help/support.

Can't FaceTime anymore? iPad states wifi connected and iPhone 4 states not connected? I have wireless in my home? Not sure what happened. Password works for iPad but not on phone?

iPhone won't connect to wifi. iPad is connected. Password working on iPad but not on phone. Can't upload software update of IOS 7.1 because phone not connecting to wifi?

Connect iPhone to computer and open iTunes. You will be prompted to update to iOS 7.0. Keep your phone connected until the update is finished.

Airplay working from Imac but not macmini

On my imac I can see all my remote speakers ( airport express and denon airplay) & connect to them, however on my macmini I only see some of them( airport express) & can connect to none.
I have tried reinstalling itunes on the mac mini but to no avail...I am at a loss as to how to fix this.
All machine have latest sotware updates installed.
Any advice gratefully received.
Thanks,
John

Jason Groff Mac wrote:
We have a Apple TV that is connected to the network via ethernet cable. The computer connected to the network via WiFi can access it via AirPlay (and can play music to it via iTunes), but neither my iPhone 5S or iPad get the AirPlay icon. Does anyone have any ideas? I see people saying that AirPlay does not work over Ethernet, but the computer seems to do fine with it.
Is the iPhone and iPad connected to the same network? Many newer routers create seperate wired, wireless 2.4Ghz, and wireless 5Ghz networks in additon to guest networks.
Jason Groff Mac wrote:
I see people saying that AirPlay does not work over Ethernet, but the computer seems to do fine with it.
Only clueless people would make such a silly statement.

Sockets work on localhost but not remotely?

hi there,
I have created a simple multithreaded client / server program.
The Server listens on port 2222 for clients. When a client connects - the client sends its ip address to the server and then disconects. More than 1 client can connect at the same time to the server and the server also listens continuasly. I have 2 problems with the program...
a) the programs work on localhost but not on remote machines? (Well not over my LAN anyway).
b) I am getting 2 lots of 'datain' when the server recieves an ip address from the client when the client should only send it once.
The code is below - any help would be greatly appreciated.
//TCPServer.java
import java.io.*;
import java.net.*;
class TCPServer {
     public static void main (String args[]) throws IOException {
          ServerSocket serverSocket = null;
          boolean listening = true;
          try {
               serverSocket = new ServerSocket(2222);
          } catch (IOException e) {
               System.err.println("Could not listen on port: 2222");
               System.exit(-1);
          System.out.println("Server Started...\n");
          while (listening)
          new TCPServerThread(serverSocket.accept()).start();
          serverSocket.close();
//TCPServerThread.java
import java.net.*;
import java.io.*;
public class TCPServerThread extends Thread {
    public Socket socket;
    public TCPServerThread(Socket socket) {
     super("TCPServerThread");
     this.socket = socket;
    public void run() {
               try {
               BufferedReader datain = new BufferedReader (new InputStreamReader
                    (socket.getInputStream()));
                    System.out.println("ip address recieved");
                    System.out.println (datain.readLine () + "\n");
               } catch (IOException e) {
                    System.err.println("Cannot read in ip address\n");
                    e.printStackTrace(); // show the error
                    System.exit(-1);
     } //TCPClient.java
import java.io.*;
import java.net.*;
class TCPClient {
     public static void main (String args[]) throws Exception
          String hostname;
          int portNumber;
          String portString;
          BufferedReader inFromUser =
               new BufferedReader (new InputStreamReader(System.in));
               System.out.println("What host would you like to connect to?");
               hostname = inFromUser.readLine();
               System.out.println("What port would you like to connect to?");
               portString = inFromUser.readLine();
               portNumber = Integer.parseInt(portString);
               System.out.println("Connecting to port " + portNumber + " of " + hostname + "....\n");
                    Socket clientSocket = new Socket(hostname, portNumber);
                    Socket sock = new Socket (InetAddress.getLocalHost(), portNumber);
                    BufferedWriter dataout;
                    java.net.InetAddress i = java.net.InetAddress.getLocalHost();
                    System.out.println("Sending ip address...\n" + i.getHostAddress());
                         dataout = new BufferedWriter (new OutputStreamWriter (sock.getOutputStream()));
                              dataout.write (i.getHostAddress());
                              dataout.flush();
                              sock.close();
                                   clientSocket.close();
                         }Oh, yeah - check out my site below, I am trying to write an audio streaming client / server in Java if anyone is interested in getting involved or just being nosey....
http://www.projectg.dsl.pipex.com

In your client you are creating two sockets (why?). One connected to localhost, the other connected to the host specified using readLine.
If your client runs on the same machine you have started your server, you have two connects to your server instead of one.
The ip adresse is sent using the socket connected to localhost. That is why it does not work on remote machines.
Hope this helps.
Jörg

I can connect my lexmark printer by usb but not wireless

i can connect my lexmark printer s400 series by usb but not wirelessly any thoughts please

I'm having the same issue. On my MBP 15" OS 10.7.3 the Lexmark printer does not connect to WIFI. It works on the USB connection. In wifi however it will work on the Virtual Box Windows 7 partition.
In my logic this means the printer is properly connected to the wifi (green indicator and working with Virtual Box and Windows 7) The MBP is properly connected to the wifi network as Virtual Box works in the Mac's environment. The printer is present in the System Preferences indicating it is Idle and does have a IP address.
When I do send a document to the printer it just sits in the Que and in System Preferences the status goes to Busy. In the Que it also indicates it is busy until it tmes out and indicate that communication with the printer is a problem.
Thanks for any suggestions.

Custom F4 help in a BSP application working in Mozilla but not in IE

Hi,
I have created a custom F4 help in a BSP application.
It is working in Mozilla but not in IE. I tried enabling javascript as well but still it is not working.
Can someone please suggest a possible solution for this?

Hi,
See simmilar discussion in thread /thread/1883519 [original link is broken]
I think this may be helpful for you.
Thanks,
Chandra

Why does the counter work in MAX, but not Labview?

Please help, I have been away from Labview for over 3 months, and I am quite rusty....
Last year, I successfully configured NI9401 to measure period (seconds) by counting the rising edges of my sensor signal. Since then, I have aquired a new PC, and loaded all my software into it, including the Labview VI's that successfully worked on the old computer.
I can see the digital signal using MAX and the test panel for the NI9401, so, I know my wiring and my TTL signal is OK, but, when I try to run the attached VI, nothing happens except the error below.. How do I tell this VI to look for the signal on MOD3/CTR0 and channel 14?
Thanks. I am sure it is a small adjustment...this worked fine a few months ago...not sure what is wrong now.
Thanks,
Dave
Solved!
Go to Solution.
Attachments:
continuously measure period buffered_singlechannel_forum_feb_23_2012.vi ‏20 KB

OK, now. Resolved the issue. The vi is fine, but, some shaky wires were identified...worked in MAX but not in the vi. Now that the connections have been tightened up, it works for both. Sorry for the inconvenience.
Dave

Works on emulators but not on mobile devices

Hello,
My project works on emulators but not on mobile devices (no image and on Samsung it says "unsupported file").
Please help, I don't know what to do. My configurations: MIDP 2.1, CLDC 1.1.
Thanks in advance.
Edited by: Vitali.pom on Oct 27, 2011 12:01 PM

Edit: I succeeded to solve it accidentally. I did the following: Sign the jar in Netbeans, clean and build, the jar didn't work, I wiped out the .ks from the jar and clean and build again. Now it worked.
Edited by: Vitali.pom on Oct 30, 2011 1:28 AM

Wifi works at home but not when away from home

My Wifi works at home but not when away from home, what is wrong? I thought with a phone plan I didn't need to have a wifi connection.

You either need WiFi or Cellular (or both). If you have neither, you can't connect to the internet.
Most people use WiFi at home and Cellular while away from home, or connect to public WiFi networks where there are some.

DSL bridged works on ethernet but not wireless.

Similar Messages

Maybe you are looking for