DSL loosing connection

Hello,
May parents are experiencing recent drop out of there DSL service.  A reboot of the modem fixes it, bit it will randomly happen again later.
Transceiver Information
Down Stream Path
Up Stream Path
DSL Speed (Kbits/Sec)
3360
768
Margin (dB)
14.0
6.0
Line Attenuation (dB)
33.7
14.5
Transmit Power (dBm)
-1.-6
2.9
I have it set up like this:  DSL modem handling DHCP to a wireless 4 port router.    Modem is a westell G90-610015-20.

Step one: Visit http://www.giganews.com/line_info.html and post up the Traceroute the page shows, if you wish. Be aware that your non-bogan public IP Address will show up.  It might shown up as the final hop (bottom-most line of the trace)  might contain a hop with your IP address in it. Either remove that line or show only the first two octets. What I'm looking for is a line that mentions "ERX" in it's name towards the end. If for some reason the trace does not complete (two lines full of Stars), keep the trace route intact.
For example this what I see
    news.giganews.com
    traceroute to 71.242.*.* (71.242.*.*), 30 hops max, 60 byte packets
    1 gw1-g-vlan201.dca.giganews.com (216.196.98.4) 13 ms 13 ms 13 ms
    2 ash-bb1-link.telia.net (213.248.70.241) 39 ms 7 ms 7 ms
    3 TenGigE0-2-0-0.GW1.IAD8.ALTER.NET (63.125.125.41) 4 ms 4 ms GigabitEthernet2-0-0.GW8.IAD8.ALTER.NET (63.65.76.189) 4 ms
    4 so-7-1-0-0.PHIL-CORE-RTR1.verizon-gni.net (130.81.20.137) 6 ms 6 ms 6 ms
    5 P3-0-0.PHIL-DSL-RTR11.verizon-gni.net (130.81.13.170) 6 ms 6 ms 6 ms
    6 static-71-242-*-*.phlapa.east.verizon.net (71.242.*.*) 32 ms 32 ms 33 ms
Step two: An original or very old style NID with a spark gap and ground wire can even get spiders in it that could cause an issue. Inspect the NID first before thinking of changes or wiring.
http://en.wikipedia.org/wiki/Network_interface_device
http://en.wikipedia.org/wiki/Demarcation_point
Running a good quality wire CAT5, no need for CAT6,  directly to the NID for the DSL modem jack may help. That is what I had done with mine. Depending on the number of loads or amount of wire in the house could also cause issues. But if the user's signal quality is not being pulled low due to a wiring issues, it would usually indicate a problem elsewhere. Unless there was noise being picked up on the premises wiring. Wire DSL directly to the NID and install a filter there for all other in house wiring may help. There used to be available what was called a NID Filter, and I am sure you can still get them.
Ideal Connection if house wiring is an issue, or very old, and lengthy. Install a filter / splitter at the NID.
Run CAT5 directly to the NID location, and install a dedicated jack for the DSL modem.
Remove all in house wiring from the NID.
Connect piece of CAT5 from the NID to the filter / splitter input
Connect all existing phone lines to the phone side of the filter output.
Connect the new DSL CAT5 directly to the NID before the filter / splitter, or to the DSL side of the filter / splitter, depending on the device purchased.
This will take all the existing premises wiring out of the picture unless there is a short circuit or excessive load somewhere in the house.
At this point all the single filters could be removed because the DSL is filtered at the NID.
http://www.homephonewiring.com/dsl.html
Step three: You can test outbound to Giganews. But giganews has/had a test that will check your inbound connection from their servers to you.
I heard from another user that
Giganews is being watched very closely because of multipart binaries, and pirated material. MP3s and Video Content. 7 years ago you could get 10-20 MP3 albums in a single day, and that was with a 15/5 fios connection. So they started providing an encrypted connection service for an added fee. I have not messed with news groups for a very long time. Now with deep packet inspection, and other enforcement, I would not even think of it. No news I want there. But there may be content that people want? They may even be checking and limiting speed from that domain. Never tested. But let me see. It looks as if reverse trace routes and speed tests are being blocked by Verizon from Giganews to my router.
        Reverse Traceroute
        Tool news.giganews.com
        traceroute to *.*.*.*, 30 hops max, 60 byte packets
        1 gw1-g-vlan201.dca.giganews.com (216.196.98.4) 0 ms 0 ms 0 ms
        2 te0-0-0-7.mpd22.iad02.atlas.cogentco.com (38.122.67.49) 0 ms 0 ms te0-7-0-9.mpd22.iad02.atlas.cogentco.com (38.122.62.193) 0 ms
        3 te0-0-0-4.ccr21.iad02.atlas.cogentco.com (154.54.31.105) 0 ms 0 ms te0-2-0-0.ccr21.iad02.atlas.cogentco.com (154.54.31.101) 0 ms
        4 uunet.iad01.atlas.cogentco.com (154.54.13.138) 28 ms verizon.iad01.atlas.cogentco.com (154.54.10.226) 40 ms uunet.iad01.atlas.cogentco.com (154.54.13.138) 28 ms
        5 0.ae1.RES-BB-RTR2.verizon-gni.net (152.63.32.157) 41 ms 41 ms 0.ae2.RES-BB-RTR1.verizon-gni.net (152.63.34.22) 13 ms
        6 * * *
        7 * * *
        8 * * *
        9 * * *
        10 * * *
        11 * * *
        12 * * *
        13 * * *
        14 * * *
        15 * * *
        16 * * Max number of unresponsive hops reached (firewall or filter?)
Step 4: Have the provider run a local loop test to see if any problems are indicated. If there are, then they could run the test with everything in the house disconnected, except the new DSL modem connection. If issues are still indicated, then the DSL provider needs to make connections on the local loop. Another user told me that they had issues when it rained, and it was because construction had left a splice box open on a line somewhere.
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

Similar Messages

  • TC Looses connection to the Internet for wireless device & new Apple TV

    I have a new TC (1 TB) that I got within the last month or two, I use it as my Internet router behind my DSL modem. TC gets a DHCP address from my DSL modem then does NAT to both Ethernet and Wifi devices behind it. After a short period of time I have noticed that my Wifi devices (New Apple TV, Macbook Pro, & 2 Iphones) will loose connectivity to the Internet, although they never loose their Wifi connection. What is strange is that I have several hard wired Ethernet devices that can still access the Internet going through the TC at the same time the wireless devices can not.
    In order to get the wifi devices back working I have done a few things, disconnected and reconnected the Ethernet cable between the TC and my DSL modem, power cycled the TC, power cycled my DSL modem. It seems like the most reliable method is power cycling the TC.
    This seems to happen pretty frequently however with no pattern or cause I can detect. The only interesting thing is that I just installed my New Apple TV and prior to that I do not recall having to recycle the TC. I am inclined to think the TCP video streaming might be overloading the TC and causing the wireless process to crap out while the ethernet ports are fine.
    Any thoughts or comments would be appreciated. Will do some more troubleshooting and will contact Apple support at some point. I will also update this thread when I find out more.

    I have a similiar problem - but I don't have Apple TV - and when the TC looses internet connection it is for wired and wireless devices. WLAN and LAN still working.
    At the same time i cannot access the configuration of the TC thru Airport - are you able to do this?
    I also have the feeling that high data loads provokes the error more often.

  • When streaming a movie with the new Apple TV, and using a DSL Internet connection, all audio sound works, e.g., the music track, but the audio track with the actor's voices, does not work. What can I do?

    When streaming a movie with the new Apple TV, and using a DSL Internet connection, all audio sound works, e.g., the music track, but the audio track with the actor's voices, does not work. What can I do?

    Hi Brian,
    Thanks restoring and restarting didn't fix my problem - i have started it fresh and still it doesn't work. Basically I press ONCE on the remote, after the machine has not had any commands for 10 minutes, and the cursor skips from one end of the menu to the other - so I can't choose network or update software etc - I sometimes manage to stop it randomly in the middle of the menu if I press on a command in the middle of the cursor skipping all the menu steps...not sure what the problem is but I have basically not used my brand new apple tv since I bought it for that reason! I should call Apple support I suppose! grrrr hate wasting time with stuff like this!
    Thanks for your help though!
    Pernille

  • Help. DSL drops connection all the time, is it the modem? (westell 327W)

    Pardon me because I'm not so tech aware, and so don't know what to do to try to find a solution.  We lose our internet connection a lot.  It seems to happen in spurts:  last night we couldn't connect at all, today it was bad in the morning but now I've been on for about a half an hour and all seems good.  I can't figure out any pattern.  Last weekend we were fine all weekend, during the week it was bad every single day. 
    I connect through a desktop and the westell modem;  upstairs we connect with a laptop and wireless.  The connection problems happen in both places, although it's our housemates who connect upstairs through the wireless and so I'm not entirely sure if they have problems when we're having problems or not (this has been going on for so many months, we've all kind of adapted to it.  but it's more and more frustrating).  Our wireless is encrypted.
    When we can't connect, we get the Explorer 'cannot find website because you are not connected to the internet' error page.  Even when we can't connect, the "local area connections" icon on the lower right side of the screen (Windows XP) says we have a network connection at 10.0 mbs.  The lights on the modem are all green, and the DSL light stays steady green, although sometimes the internet light will blink erratically, and the wireless light always blinks quickly.  We recently switched out the cable to the jack, so it's not that. 
    Sometimes we can get it to get back a connection briefly by doing one of these things (but they don't always work):
    - use the "repair" button on the local area connections window support tab -- this will often get it back for a few minutes but is rarely permanent.  When it doesn't work, it usually says it's because it can't renew the IP address
    - turn the modem on and off.  That's what worked this morning.  It did not work last night.
    - turn the computer on and off.  That worked last night only to get an initial connection that then pooped out.
    - use the verizon support popup that sometimes (and only sometimes) appears when we're having connectivity problems.  This morning that worked briefly -- the internet connection popped back up at the stage where the pop up siad "testing connection." 
    Any idea what is going on here?  I tried a couple months ago to get help through verizon online support, and it ended up as a 3 hour phone call to India that resolved things only for an afternoon, and not on any more long term basis, and I don't want to do that again unless I know what I'm asking for (since all they do is go through some kind of checklist). 

    I had similar probelm. I did find dns lookup is very slow. The following are consecutive tests:
    C:\Users\pchen>nslookup www.verizon.net
    Server:  dslrouter
    Address:  192.168.1.1
    Non-authoritative answer:
    Name:    www.verizon.net.westell.com
    Addresses:  63.251.179.13
              8.15.7.117
    C:\Users\pchen>nslookup www.verizon.com
    Server:  dslrouter
    Address:  192.168.1.1
    DNS request timed out.
        timeout was 2 seconds.
    Non-authoritative answer:
    Name:    a1280.g.akamai.net
    Addresses:  205.177.69.56
              205.177.69.66
    Aliases:  www.verizon.com
              www.verizon.com.edgesuite.net
    C:\Users\pchen>nslookup www.google.com
    Server:  dslrouter
    Address:  192.168.1.1
    Non-authoritative answer:
    Name:    www.google.com.westell.com
    Addresses:  63.251.179.13
              8.15.7.117
    C:\Users\pchen>nslookup www.bloomberg.com
    Server:  dslrouter
    Address:  192.168.1.1
    DNS request timed out.
        timeout was 2 seconds.
    DNS request timed out.
        timeout was 2 seconds.
    DNS request timed out.
        timeout was 2 seconds.
    *** Request to dslrouter timed-out
    -- when I got disconnected from internel (even westel 327w showsInternet Status: Connected DSL link:  Connected Speed (Down/Up):  3356 Kbits/sec by 843 Kbits/sec Connection Type:  PPP

  • I have just upgraded to Windows 8 and my scyning and upgrading my phone with new apple software fails, Itunes looses connection with the device (phone), cant backup the phone or download new software, is this an issues with Windows 8?

    I have just upgraded to Windows 8 and my scyning and upgrading my phone with new apple software fails, Itunes looses connection with the device (phone), cant backup the phone or download new software, is this an issues with Windows

    Hi, stig2013. 
    I would recommend the steps in the article below.  See the section labeled Verify that the Apple Mobile Device USB Driver is installed > For Windows Vista, Windows 7, and Windows 8 > Update the Apple Mobile Device Driver.
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/TS1538
    If you are receiving an error message, find the exact error number that you recieved in the article below and process the steps. 
    iTunes: Specific update-and-restore error messages and advanced troubleshooting
    http://support.apple.com/kb/TS3694
    This error occurs when the device unexpectedly loses its USB connection with iTunes. This can occur if you manually disconnect the device during the restore process. You can resolve this issue by using USB troubleshooting, using a different Dock Connector or Lightning Connector to USB cable, trying another USB port, restoring on another computer, or by eliminating conflicts from third-party security software.
    Cheers,
    Jason H. 

  • Firewire device looses connection when external screen is inserted into the thunderbolt port? HELP

    HI
    I am a recording studio engineer. Ive got a Firewire AD/DA Converter (Focusrite Saffire Pro 56) running from my Firewire port of my MacBook Pro, which is running OSX Mavericks. I've also got an external Screen I want to use as an extended display. I'm using a HDMI cable from the screen to a HDMI to Thunderbolt Converter which I then plug into my Thurderbolt Port.
    As soon as I plug the screen in, the Firewire Port looses connection completely and I cant use or even choose the Saffire Pro 56 as audio driver. Another thing happens where the Thunderbolt port replaces the Saffire Pro 56 Driver with the screen as the audio output source.
    Please help, there's nothing I can find to fix this.
    Thanks Maurice

    You don't mention which model you have, but this is from the M-Audio Firewire 410 Manual Troubleshooting section:
    The FireWire 410 has been designed to give you high performance and professional quality audio. It has been tested under a wide range
    of systems and operating conditions. In the real world, however, there is a nearly infinite number of possible operating scenarios, any of
    which could affect your system’s performance. Much like owning an automobile, “your mileage may vary.” This section can not begin to
    cover all possible issues you may encounter, however we want to give you some suggestions on common problems you may experience.
    One thing to avoid is connecting too many devices. The FireWire bus is a dependable, high-speed, high-bandwidth protocol which is ideally
    suited for digital audio. Nonetheless, it’s important to remember that audio and multimedia streaming places considerable demands on
    your processor and the FireWire bus. Although it is theoretically possible to chain many multiple FireWire devices in series, doing so may
    potentially degrade your audio performance.
    I guess this degradation could also affect the Firewire HD. Maybe there is a simple fix, but it sounds like the M-Audio people have been down this road before.

  • Wi-Fi loosing connection every few seconds on my macbook pro and its not my router's fault (running yoseomite)

    Basically I bought my new Macbook Pro retina display in September 2014. My wifi was working perfectly well for about a month or two until Yosemite was brought out. I'm not sure if it was immediately after I downloaded Yosemite or not, but not long afterwards I noticed I was having trouble with my wifi (and not just mine but my schools as well). Every time my computer tries to join the wifi network it will work for a while (5 seconds) and it will say that I have a wifi connection but then it will just stop working and it will say I'm not connected to wifi. A few seconds later and it will then reconnect and say I have wifi. I am fairly certain this is not my wireless router ( a BT home hub) as I have other devices such as my iPhone and a computer which does not suffer these problems. After a while of it loosing connection and then gaining connection it will finally stop and the wifi icon at the top will suggest I have a wifi connection but when I hover over it, I see it says "Wi-Fi:looking for networks..." and then 2 seconds later it will say "Wi-Fi: On" and it will repeat like this for however long I am on the network. When the icon appears to suggest I have a connection I am able to load a webpage but it is slow and watching Netflix can be tiresome. I've scoured these forums for information that will solve my issue however all I have found is outdated information from 2010 or 2012 or too technical information that I can't understand. Does anyone else have this problem, has anyone else found a solution, it would be much appreciated if any one could help me solve t.

    Please test after taking each of the following steps that you haven't already tried. Stop when the problem is resolved. Back up all data before making any changes.
    Step 1
    Take the applicable steps in this support article. The Wireless Diagnostics program generates a large file of information about your system, which would be used by Apple Engineering in case of a support incident. Don't post the contents here.
    Be sure to test on more than one Wi-Fi network, if at all possible. A desktop computer can be tested with a mobile hotspot, such as the hotspot created by a cell phone. If the problem only exists on one network, then the access point of that network should be the focus of your attention, not the computer.
    Step 2
    Disconnect all USB 3 devices. If you don't know which are USB 3, disconnect all USB devices except keyboard and mouse.
    Step 3
    If you're not using a wireless keyboard or trackpad, disable Bluetooth by selecting Turn Bluetooth Off from the menu with the Bluetooth icon. If you don't have that menu, open the Bluetooth preference pane in System Preferences and check the box marked Show Bluetooth in menu bar. Test. If you find that Wi-Fi works better with Bluetooth disabled, you should use the 5 GHz Wi-Fi band. Your router may not support it; in that case, you need a new router.
    Step 4
    Open the Energy Saver pane in System Preferences and unlock the settings, if necessary. Select the Power Adapter  tab, if there is one. Uncheck the box marked
              Wake for Wi-Fi network access
    if it's checked.
    Step 5
    Open the Network pane in System Preferences and make a note of your settings in the Wi-Fi service. It may be helpful to take screenshots of the various tabs in the preference pane. If the preference pane is locked, unlock it by clicking the padlock icon and entering your administrator password. Delete Wi-Fi from the service list on the left by selecting it and clicking the minus-sign button at the bottom. Then recreate the service by clicking the plus-sign button and following the prompts.
    Step 6
    In the Wi-Fi settings, select
              Advanced... ▹ TCP/IP ▹ Configure IPv6: Link-local
    Click OK and then Apply.
    Step 7
    Reset the System Management Controller.
    Step 8
    Reset the PRAM.
    Step 9
    Launch the Keychain Access application. Search for and delete all AirPort network password items that refer to the network. Make a note of the password first. Turn Wi-Fi off and then back on. You'll be prompted for the password when you reconnect. Save it in the keychain.
    Step 10
    Make a "Genius" appointment at an Apple Store, or go to another authorized service center.

  • Loose connection between Mac Mini and Apple TV 2

    Help!     I have a new Mac Mini 2.5 ghz running Lion and Apple TV2 hooked up to my 32 inch LG TV.
    Before I got the Mac Mini, Apple TV was running just fine on the same network with my Win 7 machine.
    Ever since I got the Mac Mini and I run the Apple Tv at the same time.  I loose connection on both.  My cable provider replaced the router and all my other Win 7 machines run just fine on a wireless network.  I might also add that when the apple tv and mac mini goes down, my ipad 2 goes down too.  Of course, air play doesn't work .  It comes and goes.
    I have a 2nd Apple TV 2 and hooked that up to the same tv with the same results.  I have called Apple many times.  They are helpful but not been able to solve my problem.   The cable provider and I have traced down to a conflict between the Apple TV, Mac Mini and the IPAD 2 . 
    Does anyone have any ideas what may be wrong?

    I have had multiple ATV's, desktops, laptops, and i Devices all running at the same time without a problem. Typically on a network when you start 2 devices and the connection crashes it is an IP problem. Check the IP address on both devices and see. It is usually easiest to have the router assign IPs automatically using DHCP. The router, computers, and ATVs should also be set to DHCP.
    If everything is set to DHCP try disabling DHCP and assign fixed IPs to each device.

  • Help. Changing subnet mask looses connectivity.

    HI,
     I know this is basic but is giving me a lot of head ache.
    I had a /30 between the Router(3925)  and the ASA(5515).
    Installed EHWIC on the router to support ASA failover.
    I loose connection when I change the mask at /29.
    So currently the vlan interface at the router has address 10.xx.xx.xx/30 and ASA interface has 10.xx.xx.xx/29.
    This works fine but the moment I change router's mask to /29 it looses connection.
    Cant figure out why and I have checked all I could.
    - Did shut/ no shut on the interface
    - Speed/Duplex settings are set to auto both sides.
      Its frustrating. Please help.

    Chris,
    Pasting below relevant config of both the router and the ASA.
    Router
    interface Vlan10
     description Router_FW1_FW2
     ip address 10.xx.xx.2 255.255.255.252
     ip access-group 120 in
     ip nat inside
     ip virtual-reassembly in
    interface GigabitEthernet0/0/0
     description ASA_Primary
     switchport access vlan 10
     no ip address
    access-list 120 permit ip any any
    ASA Config
    interface GigabitEthernet0/0
     nameif outside
     security-level 0
     ip address 10.xx.xx.1 255.255.255.248
    route outside 0.0.0.0 0.0.0.0 10.xx.xx.2 1

  • MacBook MB466LL/A has loose connection Any suggestions?

    MacBook MB466LL/A has loose connection in screen producing line down the middle, if I mess with it (or even wedge something between hinge by the power button) it goes away. Repair center wants to replace whole thing which I can not afford. Any suggestions?

    Have you used Software Update to update to 10.7.1. That update was suppose to fix some WiFi Issues.  http://support.apple.com/kb/HT4764

  • IMAC looses connection to Printer

    Computer will not print and seems to lose connection to the printer. I deleted all printers and made a new printer connection. Printer has address 192.168.0.14.  Later IMAC looses connection to printer again. I look at address on printer and it is now 192.168.0.15. Its done this several times. So why does the printer keep changing its address? Is there a way to set it permanently?

    Hi  I may have found what you are looking for to set the printer up with a dedicated IP Address. The printer obtains the IP address from your router, I'm not sure why your router is reassigning the IP addresses so frequently.  All of the steps for troubleshooting the Printer Does Not Maintain Wireless Connection are on available on that document, but I have copied the basics on setting up the Static IP address. (Solution five: Assign the printer a static IP address) You can review that document and try the other solutions if you continue to have connectivity issues. Locate your printer's current IP address, which you already haveOpen an Internet browser (Safari, Chrome, Firefox, etc.) on your computer.Type your printer's IP address in the browser's address bar, and then press Enter. The Embedded Web Server (EWS) opens.Click the Network tab from the EWS navigation menu.In the Wireless section, click the Network Address (IP) or IPv6 configuration, depending on your network setup.Click Manual IP, and then click Suggest a Manual IP Address.
    A manual IP address, Subnet Mask, and Default Gateway displays.Don't forget to save or apply the settings I believe you might want to try to refresh your network connection afterwards. Power cycling your router allows it to reestablish a fresh connection to all of your devices. Here's how to power cycle your network if you are unsure: 1) Unplug the power cable from your wireless router (NOTE: Do not reset the router)
    2) Do the same for the printer
    3) Shut down the computer
    4) First plug the router back in, and wait for it to fully power up
    5) Then plug the printer back in and wait for the wireless light to become solid.
    6) Once both the router and printer are on, go ahead and turn the computer back on  Check to make sure the manual IP address has stayed on the printer.
     You may also have to remove and add your printer in Printers and Scanners.Open your System Preferences, click on Printers and Scanners.Click the name of your printer, click the minus sign (), and then delete the printer.Once the printer is removed, click the plus sign (), click Add Printer or Scanner, click the name of your printer  Please let me know if these steps resolved your issue, or if there is anything else I can do to help.  I look forward to hearing from you!   Thanks, 

  • Loosing connection to my iMac drive

    Hello Support Community,
    I have an late 2012 late model iMac and a 13in Retina pro MacBook Pro.
    I do a lot of graphics work and what I used to do (before upgrading my MacBook) is do most of my graphics work on my iMac, but sometimes want to sit on the couch and use my MacBook instead.
    So i'd log into my iMac's drive on my MacBook and just access the files (so all the files stay on my iMac).
    In the last 3 months I have run into a problem where while connect to my iMac's drive, the drive would drop out (loose connection, as you can see by my pings below), which would then make my MacBook not happy and the finder would have the spinning wheel of death for a long time, UNLESS I get up and "wake up" my iMac or force quite the finder on the MacBook.
    I have set the Hard drives NOT to sleep on the iMac and made sure that wake for network activity is on, but in the past I could be connected for hours with no problem.
    Can anyone shed any light on this?
    Also, as I am transferring files from iMac to MacBook sometimes it even drops out half way.
    Here is a copy of the pings below where I am pinging from MacBook to iMac..
    64 bytes from 10.0.1.5: icmp_seq=181 ttl=64 time=167.427 ms
    64 bytes from 10.0.1.5: icmp_seq=182 ttl=64 time=189.954 ms
    64 bytes from 10.0.1.5: icmp_seq=183 ttl=64 time=110.766 ms
    64 bytes from 10.0.1.5: icmp_seq=184 ttl=64 time=134.041 ms
    Request timeout for icmp_seq 185
    Request timeout for icmp_seq 186
    Request timeout for icmp_seq 187
    Request timeout for icmp_seq 188
    Request timeout for icmp_seq 189
    Request timeout for icmp_seq 190
    Request timeout for icmp_seq 191
    36 bytes from 10.0.1.1: Redirect Host(New addr: 10.0.1.5)
    Vr HL TOS  Len   ID Flg  off TTL Pro  cks      Src      Dst
    4  5  00 0054 57b0   0 0000  40  01 0cf3 10.0.1.2  10.0.1.5
    Request timeout for icmp_seq 192
    36 bytes from 10.0.1.1: Redirect Host(New addr: 10.0.1.5)
    Vr HL TOS  Len   ID Flg  off TTL Pro  cks      Src      Dst
    4  5  00 0054 c6b3   0 0000  40  01 9def 10.0.1.2  10.0.1.5
    Thanks Guys and Gals

    Your screenshot is blank and even clicking on it just brings up an error.. the site is having issues.. has done so since the latest Apple update.
    Same with your Yosemite installed OS. It is bug farm. There are lots of issues and it is hard to get things working in a consistent way on the network.
    Redo the setup of the TC.. starting with a factory reset.
    Use only short names, no spaces and pure alphanumeric. eg TCgen5 for basestation name and TCwifi for wireless name.
    Use pure alphanumeric passwords.. 8-20 characters mixed case and numbers.
    Then if you have issues.. try manually mounting the TC.
    In finder. Use Go, Connect to Server from the top menu.
    Type in AFP://TCgen5.local (use the actual name of the TC and local is the default domain).
    If that doesn't work use the IP address. AFP://10.0.1.1 (that is the default IP in router mode.. you will need a fixed IP for this to be useful).
    Save the password in your keychain.
    Welcome to the bleeding edge. The problem with every new OS release now is the users are all now beta testers.. !

  • Got new ATV and all set up. It keeps loosing connection with iTunes on laptop and have tried everything suggested in set up guide. It works fine for a while then the iTunes account vanishes from 'computer' menu TV screen.  Full Wifi signal on both devices

    Got new ATV and all set up. It keeps loosing connection with iTunes on laptop and have tried everything suggested in set up guide. It works fine for a while then the iTunes account vanishes from 'computer' menu TV screen.  Full Wifi signal on both devices so can't think what could be causing it to happen. Any suggestions please?

    Sorry, I updated another thread I was a part of but didn't update my own thread.....ughhh!
    I updated all of my ATV 2's and 3's to the latest firmware when it was released and have been problem free since. I do believe the major issue of not being able to connect after a period of inactivity has been corrected with the latest ATV firmware.
    I can look at my network connection table using "netstat -an" in a CMD window and I do not see the massive number of connections I saw before the update.
    Here is a link to the other thread I was referring to above:
    https://discussions.apple.com/message/19952545#19952545
    Have you applied the latest firmware updates to your ATV 3's?

  • Keyboard looses connection says batteries low but just replace

    Hi new iMac 21inch with wireless keyboard. Just started to loose connection wireless trackpad working fine. Comes up with low battery warning even though batteries replaced. Then cycles through connection and disconnection constantly. Happened after 10.6.8 upgrade.

    Hello Nick:
    I seriously doubt that the update to OS X 10.6.8 is the cause of the problem.
    Try resetting the PRAM and SMC.
    If that does not help, I would return the KB for a warranty replacement.
    Barry

  • Issues with client looses connection with 6.0.196.0

    Hi,
    We recently upgraded our Wisms to version 6.0.196.0 and after the upgrade we have seen the clients sometimes looses connectivity and has problems to connect. We use an network with 802.1x  and PeapMschapv2 with dynamic WEP.
    We have disabled aggresive load-balancing but still see the issues.
    Any ideas anyone?
    Regards,
    Martin

    Hi,
    Any news for these problems? Did the version 7.x fix these CAPWAP UP/DOWN problems with HREAP APs? It seems that I'm having these same problems now. Local APs seems to be fine, but HREAP APs goes UP/DOWN with versions 6.0.196.0 and 6.0.199.4.
    There are three 4404 WLCs, where are different sites' office and warehouse APs connected to. The environment is configured as N + N + 1
    like following:
    WLC1 is for officeAPs. APs are 1131 and they're configured as H-REAP
    WLC2 is for warehouseAPs. APs are 1242 and they're configured as Local
    WLC3 is for backup and I used this for testing.
    After I updated all the WLCs at summer to version 6.0.196.0, there have been issues where the clients looses randomly WLAN-connections. But the complaints just came from the two largest offices. And these didn't happend immeaditly after the update, but after few months. It can be that the summer holidays was reason for it. After some investigations, I updated the WLC3 for version 6.0.199.4, which just got released at the time, and moved these two largest offices' APs to there. Complaints stopped but after a month the second largest office informed that the clients' disconnections started to raise again and the WLAN-network has become unstable again. First there was just couple of issues but it have been raised as the time goes by.
    When I made some more investigation to this site, I noticed that the APs' CAPWAP goes DOWN and UP randomly for a second:
    *Nov 12 07:39:29.537: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN
    *Nov 12 07:39:29.590: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *Nov 12 07:39:29.590: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
    *Nov 12 07:39:29.759: %CAPWAP-5-CHANGED: CAPWAP changed state to UP
    *Nov 12 07:39:29.811: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Nov 12 07:39:29.812: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Nov 12 07:39:29.849: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
    *Nov 12 07:39:29.850: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Nov 12 07:39:29.889: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    Then I investigated some more and noticed that this happens on all of the H-REAP APs and almost in the same time:
    *Nov 12 07:39:29.537: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN - WLC3, second largest site's AP (6.0.199.4)
    *Nov 12 07:40:17.439: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN - WLC3, second largest site's other AP (6.0.199.4)
    *Nov 12 07:41:20.297: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN - WLC3, largest site's AP (6.0.199.4)
    *Nov 12 07:42:31.928: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN - WLC1, random site's AP (6.0.196.0)
    When I checked the warehouseAPs, which are configured as local in the WLC2 (6.0.196.0), there was nothing like this in the logs. Logs are clean.
    But when H-REAP is configured for these APs, the clients should not be disconnected when the CAPWAP goes down? And this whole "process"  seems to last just for a second. Not sure if this is the real reason for these client disconnections, but at least this is not normal. I haven't heard complaints from smaller sites, even when APs at them also does the same.
    I don't feel great to update the WLCs for the version 7.x, because it just seems to be new feature release, but if it fixes these, then I should think about it. Has someone, who had these same problems, got this fixed with version 7? Or has TAC provide some other patches for this?
    Thanks,
    Joni

Maybe you are looking for

  • HP Officejet Pro 8500 A909g can't scan to network folder

    Since upgrading to 10.7 Lion, I have not been able to scan to a network folder on my mac. Have downloaded the latest driver from HP, and reinstalled the driver etc, but to no avail? Any thoughts?

  • Customizing credit limit

    Hi all i habe the following problems, I customiz the credit limit and it work well, but the Message to the credit manager can not be sent. when i create a sales order, i can see the message in header output well, when i save the Order i become a mess

  • Printer prints letters with wrong spacing

    When I print a webpage from Firefox it (always?) prints what seems to be the right letters but with hopeless spacing between the letters -- usually overlapping each other so it is unreadable. This is exactly the problem discussed in Bugzilla@Mozilla,

  • NCQ on iMac G5 (non-iSight)

    Anybody know whether or not iMac G5 1.8GHz (non-iSight) has Native Command Queing (NCQ) support on the SATA bus?

  • 2 SSDs: RAID or not?

    Hello! I would like to know what's the best path to be taken in my case. I have two 256gb SSDs. 1st option: 2 partition (OSX + Bootcamp) in one drive and 1 partition in the other one for sharing data between them. 2nd option: Raid them and make it 3