DSL Modem/Router Upgrade

I am tired of my modem/router dropping connection when playing my Xbox for awhile. It kicks me out of games and parties. I am considering Netgear's new NETGEAR Nighthawk AC1900 Wi-Fi VDSL/ADSL Modem Router (D7000-100NAS)to replace my existing modem/router as it seems to be more powerful and better suited for gaming. Has anyone used this new Modem/Router and would ATT support it?

Hmm, I think that the gateway might just be defective if it's just rebooting randomly on its own. Make sure you try different outlets to rule out faulty electrical wiring. If the gateway is on the floor and it's carpeted, try moving it to a different surface.
I see that you mention you have a 7550, because of that, you SHOULD be able to use the D7000 with your service in replacement of your 7550 and WNDR4300. Just make sure you purchase it from somewhere with a good return policy in the case that something goes wrong.
When installing a new device, make sure you have your AT&T username and password ready if asked during device PPPoE setup.
Just remember that when using a non-AT&T supplied gateway, you aren't guaranteed to receive support from them for certain things. You must be prepared to instead contact NETGEAR.

Similar Messages

WiFi Problems w/ OS X 10.4.11 and Speedport W 502V DSL Modem/Router

We just moved to Germany again, so went to Deutsche Telekom (DT) for Internet/phone access. They sold us a Speedport W 502V DSL Modem/Router with manuals--all in German, as DT does (DT offers NO support in English; some would argue they offer no customer support at all).
Babelfish and I managed to configure a late-model eMac, G4 PowerBook and two iPhones with the DSL router, with pretty good success (sometimes we have intermittent Internet connectivity). Then our household goods were delivered and we unpacked and set up the G4 dual-GHz tower. So...the G4's Airport (not Airport Extreme) "sees" the WLAN and the https://speedport.ip site "sees" the IP address of the G4, but the G4 can't join the network, no matter what I try. It's to the point that I think it's something painfully obvious that I'm missing and I must be too far in the weeds...so now I need fresh eyes on the problem.
I have no computer connected to the Speedport, and wouldn't have thought that was the problem because the other non-physically-connected computers are using the WLAN network. Thanks for any help!

hi kathryn
did it have to be the Telekom, by all means??
anyway, first of all a link to a video where a german comedian writes a letter to steve jobs demanding he chose any carrier but the DTAG for the iPhone distribution in germany - really funny!
http://bit.ly/4B4OdQ
OK, I´m currently downloading the speedport manual from their website and will look through it, in order to see if there´s something in there..
as a first guess I´d try looking at the wireless prefs of that speedport box. I guess it supports by default 802.11a/b/g, whereas the G4 only does 802.11b (the "normal" airport). Try selecting only the 802.11b portion from the speedport (that makes networking somewhat slower for airport express computers, but shoudn´t be a problem since it´s still at least as fast as basic DSL service (11MBit vs 2 or 6 MBit)
cheers
Matt
(german in spain)

Airport Expess with DSL Modem Router

I had a DSL Modem Router with 3 computers plugged into it via ethernet and was working fine. I then replaced one of my computers with a laptop so bought an AE and plugged it into an ethernet port on the DSL modem router. It worked fine for about 4 days then all three computers internet connections went down. I have got the two desktops working again with the AE disconnected but am worried that if i connect the AE again the same thing will happen. Is there any way that i can avoid this from happening? is this because i am doubling up the routing if you know what i mean?
MacBook Pro 17" Mac OS X (10.4.7)

First welcome to the discussions,
This isn't that uncommon, many of us expieriance drops in service and have to reset our systems.
There could be any number of reasons that cause this from a Power Spike to surges from power company, to storms from wind and lighting.
If you are lucky nothing gets fried and a simple reset will take care of the problem. Other times it can fry about any component and sometimes it's hard to find exqactly what is fried. If you are able to reset and get everything up and running again I wouldn't worry to much, I would consider a Battery Back-up to add to your Network to save your equipment though.
Cheers and Good Luck.
Don

Best DSL modem/router?

I'm sure this question has been asked but how recently, I wouldn't know. We have a D-Link DSL modem/router sent to us by Verizon in 2010. My desktop Mac is connected via Ethernet to the modem. Our other devices use Internet via WiFi. Verizon can sell us a new basic modem, of course. But I'd like one that has a stronger WiFi signal. Can anyone suggest a specific brand and model that will work with our DSL and emit a stronger signal? Thank you!

sherylsrtx wrote:
I'm sure this question has been asked but how recently, I wouldn't know. We have a D-Link DSL modem/router sent to us by Verizon in 2010. My desktop Mac is connected via Ethernet to the modem. Our other devices use Internet via WiFi. Verizon can sell us a new basic modem, of course. But I'd like one that has a stronger WiFi signal. Can anyone suggest a specific brand and model that will work with our DSL and emit a stronger signal? Thank you!
get your own router/wap and connect it to the modem.

Can Westell 327W DSL modem/router receive wireless signal?

I have a spare Westell 327W wired/wireless DSL modem/router. I need a wireless access point for a G4 Power Mac away from an Apple Extreme. I knew how to make the Westell 327W in a bridge mode. Is there a way to make 327W communicate wirelessly with a FIOs modem/router?
Thank you very much.
Robert

Hmmm, perhaps something like this with a USB extension cord would be a solution, they have better Range even without an extension than Airport cards ime...
http://eshop.macsales.com/Item_XLR8YourMac.cfm?ID=10303&Item=NWTMXP802NU2C

DSL Modem / Router for Airport Extreme / Express

Please can anyone advise re the best DSL Modem / Router to use with an Airport Extreme and Express.
I am in the UK with BT Broadband. I currently have a Netgear DG834G which has been great but seems to need a lot of re-setting recently and has been dropping the connection. I've checked our line with the provider and that seems to be OK. The Netgear DG834G is currently wired via CAT5 to my Airport Extreme which is then also wired to an Airport Express to extend the network.
We are in a rural area so don't have particularly fast Broadband speeds (max tends to be around 4MBps).
As I'm using the Airport Express / Airport Extreme for my WiFi I don't necessarily need a modem / router with wireless or anything that has bells and whistles or can make me a decaf macchiato...I just want something this is bomb-proof and super reliable.
I've looked at various forums and am just getting confusing stuff re what works and what doesn't.
We are due to get fibre-broadband in our area next year - very happy to have to get a new router then for that if needed. The important thing for me is to have a decent set-up for now.
Many thanks! Eddy
Using Macbook Pro and iMac on 10.9.5

You don't need a modem/router since the AirPort Extreme is a router.
I don't know what the best modem might be....that would involve testing hundreds of products, and even if we could come up with a "best" modem for the AirPorts, it would likely not be the "best" working the BT connection, or BT would not support the product......,but you might want to take a look at the Draytek Vigor 120 modem, and then check with both the Draytek support folks and the BT support folks to make sure that the modem will be compatible with your service.
Vigor 120 ADSL Modem - Draytek
If you are due to get a fibre connection in the future, then you will have to start over again modem wise at that time.

How to configure WRT350N as a router in a network wih a DSL modem/router

Hi,
I'll really appreciate if somebody please could give me some help.
The problem is that I have a Dlink DSL-2640B modem/router AND a Linksys WRT350N router, what I want to do is how to configure them so they both are in the same network, and the WRT350N has access to internet and the computers connected to the DSL-2640B.
Is that possible?....OR...the other option I was thinking was leave the DSL-2640B as a modem only, and have the WRT350 make all the routing wired and wireless.
I'll really appreciate your comments.
Regards.

As per my knowledge it is better to use the wireless router to provide connection to wired & wireless computers. Leave the DSL2640B as a modem, connected to internet port on wireless router.

WRT54G & Westell DSL Modem/Router

I want to use the WRT54G as a WAP or signal repeater to extend the range of my Westell 327W DSL modem/wireless router. Is there a way to do that? I'd like to put it halfway between my wireless router and another wireless computer in my house.
Message Edited by rweintra on 08-08-2007 05:13 AM

That router can not be used as a repeater. You can turn it into a wireless access point but it will not repeat the signal from another wireless router with the linksys firmware. You can try to look for a third party firmware that may give you that option but if you do install a third party firmware it will void any warrenty you have on that router.
Check this LINK for other firmware.
Richard Aichner (Ikester)

Install RVS4000 with DSL modem / router combo?

I'm trying to install a RVS4000 VPN router in our small office. My problem is that AT&T has installed a Netopia 3347-02 DSL combination Modem / router. So I can't connect the RVS4000 directly to a dsl modem, the only access I have is on the Lan side of the Netopia. When I tried to set the WAN side of the RVS4000 to the same subnet as our Lan, it wouldn't let me do that. I tried setting the Lan side of the Netopia and the Wan side of the RVS4000 to (the same) slightly different subnet, but that didn't work either. The only way I can get internet access going through both devices is to connect the Lan side of the Netopia to the Lan side of the RVS4000, but that bypasses the VPN, correct? The reason I bought the RVS4000 is for the VPN. Is there a way to configure the RVS4000 in this situation, or do I need to get a plain old DSL modem without a built in router?
Thanks, Scott

Scott,
You should not need to get another device to use the VPN functions of the RVS4000. To setup the equipment you have, you just need to place the Netopia DSL router into "bridge" mode. This will then allow you to connect the DSL router to WAN (internet) port on your RVS4000. Once in bridge mode, your WAN port on the RVS4000 will receive its IP address from AT&T, which will then take over all routing functions, and enable you to use the VPN feature of this router.
If your DSL provider is using PPPoE, you will need to select "PPPoE" on the WAN setup page of the RVS4000, then enter the username and password into the RVS4000 so that it can authenticate and get an IP address from AT&T.
To place the Netopia DSL router into "bridge" mode, I am including a link to one of their user guides. The section for placing it in bridge mode starts on page 107.
http://www.netopia.com/support/hardware/SoftwareUserGuideV761-Clsc.pdf
Thank you,
Darren

IChat Tiger 3.1.4 (v432) resets my DSL modem/router

iChat has always worked untill one month ago on old speedtouch home. Frequent disconnects in the middle of a video conference. Now I have ne new modem/router form my provider, Speedtouch 546, and have internet connection. iChat can start up and connect to the net, see my buddies but can never initiate or accept a video conference. I click "accept" but it reports as if I have declined the invitation. Then ALL lights on my modem turn off, and it will reboot itself.
I have looked at Ralph's pages and opened my mac OS X firewall and have opened the port on my speedtouch in the NAPT section.
But...no way of testing if it works.

Hi Aram,
Welcome to the Apple Discussions
Alcatel Speedtouch 500 series have SIP, a protocol iChat and VoIP devices and apps use, bound to port 5060.
In earlier devices that have version 4.x.x firmware this can be unbound. See here in the white text box a bit further down the page http://www.ralphjohnsuk.dsl.pipex.com/page4.html#_text
Now later devices (normally ending in 6) or those others that have version 5 or 6 firmware can not unbind SIP from port 5060.
The one solution that has been foound has been to put the device in Bridge mode.
11:52 PM Thursday; June 22, 2006

Link an 871 router/switch wirelessly to an ISP-provided DSL modem//router?

Hi, Upstairs we have a 20-Mbps ISP-provided DSL wireless modem/router, and one floor lower, in basement, I would like to install a refurbished 871 Cisco router, without adding a separate Internet connection. I would like the 871 to connect wirelessly to the DSL router. To the 871 I would wirelessly connect 2 workstations, one of which will host 3-4 virtual machines. The 2 main reasons for this weird arrangement are so my virtual machines and virtual switch do not interfere with upstairs devices connected to the DSL router, and so I can practice Cisco router//switch configuration downstairs where I reside, without added expense of a separate Internet connection. Would I need a separate repeater between the two routers? Humbly requesting any other feedback.
Jeff

To have all routers using the same Network Name and wireless password, you would have to configure them for a roaming network. This would require that the Extreme and Express connect individually back to the Pirelli router via an Ethernet connection.

RV120 Bridged with DSL modem/router

Hello,
I am working overseas for a small company, trying to get an RV120 VPN router to connect to our network back home. Part of the problem is that I have to use a DSL modem here which is also a router, and so the WAN IP given to the modem is not the same one used by the VPN router.
Do we need to create a bridge between the two routers so that the VPN router can use the WAN IP from the ISP instead of a DHCP address on the local network? Or is this the wrong approach?
Any assistance is appreciated. I am a software engineer, not a networking/IT person so most of this is unfamiliar to me.
Thanks,
Dan

The DSL router does have VLAN capabilities, would that help? I briefly tried the DMZ solution, but didn't seem to make any progress. So when using the DMZ, would the VPN router still have an IP relative to the DSL router (10.1.1.x, etc. in this case, if the DSL router is 10.1.1.1), or should it try to takeover the actual WAN IP that the router uses?
Thanks

Trouble using Airport Express Base Station with DSL modem, Router and Hub

About 18 months ago, I had an Airport (802.11b) with WAN & LAN ports and modem hooked up to support two laptops, a Titanium Powerbook G4/600 and G3/400. The setup went from DSL modem -> Linksys router -> to Airport -> Hub (which had desktop and ethernet laser printer plugged in). The network worked fine.
Then, I got a G4 iBook to replace G3/400. Wanted to get 802.11g to support “g” Airport card in iBook. Got a Linksys 802.11g Wi-Fi with 4-port router for $50. Hooked it up directly with DSL modem. (Couldn’t get it to send out to hub). Hooked the desktop and ethernet laser printer into Linksys Wi-Fi/router. The only way I could use the printer was by having it be a shared printer from the desktop. This was often problematic.
Two months ago, I got a refurbished Airport Extreme Base Station. I can’t get the AEBS to interface directly with the DSL modem, so I hooked it up as follows:
DSL modem -> Linksys router -> to AEBS -> Hub. I plugged my Epson 820 (USB) into the AEBS and can see it to print to.
I have a static IP. That info is entered into Linksys router. Router set as Gateway, with DHCP enabled. AEBS is set to Connect using Ethernet, Configure using DHCP. Network setting: Distribute IP Addresses is unchecked.
Here’s my issue:
I can’t see the ethernet laser printer. It will occasionally flash available, but is gone in less than a minute. The printer is HP 2100 series.
Sometimes I can connect to the desktop G4 tower; most times I can’t.
I have checked and double-checked the cables.
Both the printer and desktop are connected to the Hub.
What can I do so that I can see the HP 2100 series printer and the G4 tower?

Don,
Thanks for the suggestions. Glutton for punishment that I am, I tried this again, “just for grins.“ The six other times I tried this, I couldn’t get the AEBS to “see” the Internet. And lo, this time it worked. Here’s the setup now:
DSL modem -> AEBS -> 4-port hub (which is connected to G4 tower and HP 2100 Ethernet printer). My USB Epson is connected to the AEBS, and I can print from the laptops. AEBS is set up: manual IP info, Network: distribute IP address; share a single IP using DHCP.
When I still couldn’t see the desktop G4 and the Ethernet HP 2100 connected via the hub (not), I got a flash. I had swapped out the cable a number of times to no avail. Then I realized, the hub is old and all the cables I was using are the new CAT5s. I dug out an old four-wire with RJ45 connectors that my husband made years ago (probably a cross-over cable). It was quite an effort as the cable is 30 ft. long and wrapped around the perimeter of the office behind desks and file cabinets, entwined with all the other wires. But I plugged it in and, Shazam! I am WORKING!
And, Don, thanks to you, I have eliminated the router from my gaggle of electronic boxes.

Time Capsule + 2Wire 1701 HG Gateway DSL Modem/Router

I'm posting this note in that hopes that maybe some lost soul will stumble across it and take heart. Some things do indeed "Just Work," but it might take 10 or 15 person-hours to reach that state.
This was Trouble with a capital T.
It took me about a week, the ISP tech support people a couple of hours in two phone sessions, and finally Apple Support about a half hour to get it running.
The first two times I tried to set it up (even though I'm kind of an RTFM kind of guy) the Time Capsule and I managed to completely bring down my network and to disable the modem all the way to hard reset.
The third time, I got Apple Support to talk me through it, and now it's happily munching away, backing up my main drive.
The root problem, according to Apple support, was that the 2wire is a combined modem/router, so that, unless the guy at the keyboard pays very close attention to the step descriptions and understands all the subtleties, he can get both 2wire and TC trying to assign addresses on the network and really screw things up.
The Apple-phone-support-prescribed sequence that ultimately worked was shutting down everything attached to the modem then restarting in order, modem, TC, finally MacBook. During the re-setup process the 2wire website somehow detected the need for a modem firmware upgrade and offered to download and install it.
Finally the TC's green light came on, and everything seems to be working to spec.
Now I'm a happy guy, but there's no possible way I could have gotten that out of a manual, and if it hadn't been for Apple's willingness to provide human phone support, the TC would have been on it's way to the dump. Well ok, I would have waited 'til the next E-waste day. Apple support gets point for running a down home blues on their 'hold' track.
Hope this helps someone,
rj

This 2Wire modem/router has been nothing short of a pain in my nether region.
Is it possible to disable the 2Wire's router capabilities and use only the Time Capsule's router capabilities?
I'm going to give your suggestions a shot. Keeping my fingers crossed.

DSL modem/router needs to be just a modem to take advantage of TC?

I just bought a time capsule and was finally able to set it up to back up my MacBook Pro. I think I will be very happy with the product. I am new to the support side of the Apple website and was hoping somebody could help me out with a question. I would like to use the time capsule as a router but since I have a combined modem/router From my DSL Verizon Internet connection, AppleCare said I could not use it as two different routers or there would be problems. I was told that I needed to call Verizon to find out how I turn off the router capability/portion of the combined modem. Does this make sense to anyone? Does anyone have any good ideas on how I can accomplish this easily? The device appears to be a ActionTec Verizon brand modem model number MI424-WR rev D

I was told that if the time capsule is in bridge mode, it can only backup up one computer. Is that accurate?
This information is not correct. A Time Capsule in Bridge Mode will allow multiple Macs to backup, with the practical limit being about 5 or 6 Macs.
I have 3 Macs backing up regularly to a TC in Bridge Mode, and there have been no error or delay messages with the setup.

DSL Modem/Router Upgrade

Similar Messages

Maybe you are looking for