DSO 6032A KEYSIGHT SCOPE OLDER DRIVER

hey evreyoe.
with my automatic STE we use in test stand 2.0 and windows 2000 (very old).
til now we use the agilent model 54622a scope. now we replaced to model DSO 6032A scope.
some error came from the scource file "ag5462x.c line 1410/1415.
actully, i think its because its not the same source file and i need a newer cvi driver for this scope.
i found here, but is not for windows 2000, (xp and up).
sombody can help me with fitted driver?

I don't think there is a driver for Windows 2000 for this device. You may need to upgrade your OS to use this new hardware.

Similar Messages

I have new hard drive in macbook pro(08) and have SATA cable with external power source to old hard drive (10.5.8)via. USB port and newer drive(10.6.8) will not recognize older drive..Do I need to partition newer drive with older disk to recover data?

I have new HD 750GB Hybrid in 2008 Macbook Pro 17" w/ Snow Leopard 10.6.8 connected to old Hard drive(250GB that had 10.5.8 on it at time of failure) via SATA cable to USB port with external power source.. Computer not acknowledging old HD at all in Disk Utility or otherwise (that I'm aware of)..Do I need to partition New HD and load old(10.5.8) onto partition to recognize older drive for data recovery? Thanks Wayno08

You do not need to load 10.5.8 onto your new drive in order for a 10.6.8 system to see the contents of a 10.5.8 system.
You might want to check out the hard drive troubleshooting bootk in the downloads section of this web site:
http://scsc-online.com
They also sell a product named Phoenix that can do OS extraction and volume copying/cloning, but to be honest I don't know if it's appropriate in this case.
I would suggest the following:
Open up Terminal.app (under utilities) and type "diskutil list" without the quotes. This is the command line version of Disk Utility. If the external drive doesn't show up at all, then it's likely not connected properly, not getting power, or just plain dead. If it shows up with only a devce name like disk0s16 but no volume it means the drive is seen, the OS just can't make sense of it.
Assuming the drive shows up, I would try to boot off the original installl disks for the system and run Disk Utility from that. I'm assuming the drive will show up. You'll want to select the option to repair the drive and then perform the option to repair the permissions.
If the unit isn't showing up, as per step 1, try a different USB port. More importantly with your unit, try it on another side of the unit if possible. If you read the book I referenced above, some of those units have I/O boards that are separated from the logic board. If the cable from the logic board to the I/O card goes bad or has problems, which isn't all that uncommon, some or all of the ports on the I/O card may appear to be bad as well. If you use a USB port on another side, it would be routing out of a completely different I/O path, so that's a potential problem.
If the drive is only seen with a device name such as disk0s16, it's likely either the index files are corrupt beyond Disk Utility's ability to see them. The only thing that I think would help would be a product named DIsk Warrior, but I can't guarantee that.
Disk Warrior can be found at:
http://www.alsoft.com/diskwarrior/
The company that I linked in the first link above also makes a product named Scannerz that does HD and system testing. The Scannerz/Disk Warrior combination make a good pair because the complement each other....Scannerz does what Disk Warriror can't and Disk Warrior does what Scannerz can't. However, at this point I'm not too sure getting a tool like Scannerz would be of much use because it sounds like the damage has already been done.
Let us know what happens.

HOW TO INSTALL OLDER DRIVE for EPSON r1800

Hello
SInce I upgraded to Lion, my Pictures are no longer printing as WYSIWYG on my Epson R1800. It seems from forums, that the newer driver isn't working corectly. I was able to find the installation DMG of an older Driver - but it is not found by the R1800 under System Perferences. Can you tell me how to install an older Driver?
THanks
Art

"...It seems from forums, that the newer driver isn't working corectly..."
What forums? The driver should work properly.
http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?BV_UseBVCookie=yes&oid= 14121&prodoid=53540919&infoType=Downloads&detected=yes&platform=OSF_M_X7

Finding an older driver version for LaserJet Professional M1212nf MFP

Dear all,
I am looking for an older driver version for our HP LaserJet Professional M1212nf printer, since with our SAP-Citrix system I could only print reports from that version. The version is 20100331 (1.0.1.19178). Is there any place where I could find this driver version? If not, is there any way to transfer the printer driver to the new computer?
In the meantime I found the HP FTP path where various drivers can be found: ftp://ftp.hp.com/pub/. However, I don't know where I could find the driver I am asking for. Could please someone help me with this?
Best regards,
Radu

@RaduPopa ,
I have brought your issue to the attention of an appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post personal information (serial numbers and case details).
If you are unfamiliar with how the Forum's private message capability works, you can learn about that here.
Thank you for visiting the HP Support Forum.
I work for HP. However I speak only for myself, not for HP nor anyone else

Corrupt hard-drive, swapped for an older drive from another similar MacBook Pro

My original hard drive is corrupt, I swapped to an older drive which has snow lepoard on it, when installing Yosemite it freezes now i cant boot into the old OS and installer freezes extracting.
Disk utility says the disk is fine, with no issues.
The original disk failed and would not boot, disk utility says it was corrupt. I have another MacBook pro so i swapped the HD's, it is 320GB compared to the 500GB (failed drive).
It was working fine on Snow Leopard but when I ran the upgrade in the App Store, it freezes everytime at the same point in the install ( extracting the same .pkg file).
Any ideas?

You apparently have a MBP that came with an OSX newer than Snow Leopard. If that is the case, the Snow Leopard HDD will not boot in the newer MBP. If you erase that HDD and install the OSX that came with your MBP (or a newer one), then it will be compatible.
Ciao.

Having issues with Mounting older drive/time machine

Hey folks, I'm having issues with mounting a ex hard drive. It works, but there is a passcode for it, due to being my time machine drive, I dont remember the password, is there anything I can do to reset it? if not how do I wipe it clean? I went into disk disk Utilities and everythink looks fine.. Check out the pics Iput up

I dont remember the password, is there anything I can do to reset it?
No.
if not how do I wipe it clean?
If you can connect the drive to a computer running Windows or a version of OS X older than 10.7, erase the drive that way. Otherwise see the link below.
Hard disk bricked after using file vault with time machine

Configure ag6000 Scope IVI driver to use math channels

Hi all,
just before capitulating using the generic Teststand-IVI Scope driver capabilities, one try get help here:
We want to use a ag6000 compatible scope with teststand. The first guess is to use the ag6000 IVI compatible driver, and directly use IVI-scope steps within teststand.
Connection and step usage works so far, but:
1. How do I configure the math channel to be used from within teststand? The ag6000 driver itself provides the necc. functions when used with CVI, but the generic Teststand IVI Steps don't have this functionality (or I'm to blind to find it?)
The alternative approach I'll start, is to encapsulate the ag6000 driver in a cvi DLL and use this within teststand.
2. Unsupported feature seems to be having an AUTO trigger or something like a continous measurement. (We also need to measure DC without crossing any trigger level)
Any Ideas?
David

All of the functions in the IVI are defined by the IVI Foundation - not NI or TestStand. They pick the functions that are most common to all scopes. If there is a specific instrumention function that you need to use, you have to use the specific driver for the scope. Doing that, of course, removes a lot of the reasons for using IVI in the first place.

Older drives into a newer intel

I have a couple of drives that came out of an older, PPC G5. What precautions should I take when installing them in the Mac Pro? Any possible damage? Thanks.

Thanks Martin. Didn't know about the screws. Will remove them prior to installing.
While we're on the subject of Mac surgery, is there anything special I should know about replacing/upgrading the ram? Did some on the old G5 but I'm sure things have changed over the years.
Thanks again.

IPrint drivers not overriding older driver on client

Hi
Using iPrint client (v540) and HP printers.
We installed printers at image time using a command line.
Printers were giving problems (spooler crashing), so we wanted to change to UPD.
So, we modified the drivers on the IPP servers to be UPD.
I then created a policy to push the printer out again, and update the driver.
The policy IS applied successfully, but when I check the printer it still says it is using the old driver, not the UPD.
I am not specifying anything in the policy other than:
- The IPP printer path
- The checkbox for "Update iPrint printer driver while installing the printer"
The policy is enforced and is being applied successfully (checked form device and ZCC).
Any advice as to why it is not using the new driver?
Thanks.

ClemClark,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Visit http://support.novell.com and search the knowledgebase and/or check all
the other self support options and support programs available.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://forums.novell.com)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://forums.novell.com/faq.php
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://forums.novell.com/

LATEST NVIDIA DRIVER OR MSI OLDER DRIVER

I'm currently using MSI 311.06 driver but NVIDIA has already released version 320.18.
Should I update to NVIDIA driver and why?

newest drivers include fixes and peformance optimizations
so try latest one, go back to msi one only if you have issues with nvidia one

Older Drive Modules

Recently made the Intel transition after years of steadfast performance from my XServe G5. My new Intel XServe is using two drive bays with mirrored RAID. I've wanted to keep the old XServe G5 boot volume around just in case I need an old config file or log, but there isn't really a convenient way to mount it.
Supposedly, the XServe G5's drive modules are not supposed to work with the Intel XServe, but I popped one into the spare drive bay and it mounted immediately. I'm guessing that Apple says they're unsupported due to lack of hardware monitoring and so forth? That said, I see no harm in temporarily parking my old drive module in my new XServe, as long as I'm not actively using it for boot/write.
What is people's experience with using old drive modules in new machines or vice-versa?

DaddyPayCheck? I know you have some input on this... I accept links to old posts that didn't show up in my search results.
Pretty please?

MyDAQ is not recognized under Window7 (32b) - "upgrade" to older driver version??

Hi,
although my myDAQ appears in the Windows device manager without exclamation marks and the blue LED lights up, the myDAQ does not appear in MAX and I am not able to use it.
Starting up NI myDAQ Troubleshooting Utility yields the following strange error message:
Device Drivers Installed (Failed)
- Using DAQmx Driver Version 9.3.5f2 . Please upgrade to version 9.1.1 or higher before using the myDAQ device. (Critical Failure)
- Using ELVISmx Driver Version 4.3.89.0. Driver version exceeds requirement.
Any idea what's going on there?
Best regards,
Christian

Hi Christian,
I would recommend you to UPgrade to the latest driver version 9.5.
That should hopefully solve the problem.
Cheers, RMathews

Hd intel 4000 code 43 on windows 8.1 - It only works with an older driver version

Hi there I have an HP Pavilion Sleekbook 14 PC (HP Pavilion Ultrabook 14), with a 18FA motherboard - version 82.23, F.12 Bios, and a Intel(R) HD Graphics 4000. The graphic card only works with the 9.17.10.2932 (12/12/2012) driver, and everytime I try to update to a newer driver version, it shows the "Code 43" error. Does anyone knows how to update the drive and solve the "Code 43" error? Without solving this issue, I can't install the Windows 10. I've tried to update to Windows 10, but it doesn't run this old graphic display driver and it only gives me a blue screen, and if I install a new driver version, there it comes the "Code 43" error. Thank you, guys.

Hi ,
Thank you for visiting the HP Forums! A great place where you can find solutions for your issues with help from the community!
I came across your post about the Notebook, and wanted to assist you! I have looked into your issue about your HP Pavilion14 Sleekbook and issues with the Drivers for Windows 8.1. If your computer is having problems finding and installing operating system updates, try using the Windows Update Troubleshooting tool to fix the problem.
I would be happy to assist if needed. How Do I Find My Model Number or Product Number?
Please let me know.
Thanks.

How do I erase an older Western Digital 1TB mirrored hard drive? Newer drives can be erased via a WD Utility, but the WD site says to "ask Apple" about the older ones.

I have a MacBook Pro with OSX 10.7.5. The hard drive is approx. six years old - a Western Digital for Macs, mirrored with 1TB on each half.
Because the drive is "infected" with Time Machine backups that I can't erase, I have removed all important files from the drive and now want to wipe it clean. I've done this with new drives, via the WD Utility that came with the drive, but the older drive doesn't have such a utility. The WD site only has a protocol for PCs.
I find nothing on the Apple site itself. Can you community members help??
(I've tried various ways of deleting the Time Machine backups, but nothing has worked. The instructions for that, which I read on a community support site, were too advanced for me to understand. A Mac IT guy tried to erase the backups, but he didn't know how either. So that is why I'm erasing the drive totally. I've learned my lesson and have a dedicated Time Machine drive now.)

Please be clear:
This is a mirrored RAID that you use as the startup disk?
You now have a different startup disk and wish to erase the RAID mirror?
Do you wish to continue using the RAID for backup?
If all you want to do is erase the RAID to get rid or the Time Machine backups, the use Disk Utility to erase the mirror disk mounted on the Desktop.

How to get older nvidia driver

I just installed archlinux again and the nvidia driver.
Now when I run 3d games I get a stutter every 13-15 seconds, as if the graphics freeze for 1 second.
I remember having this problem with the nvidia version 169, and then I downgraded the driver which fixed the problem.
But this was in Gentoo.
How do I get an older driver in Archlinux?
I think I need the 100. something driver.

I haven't tried using ABS yet. The question is for me if it will be easier for me to install Gentoo again where I can just choose the driver version freely, or llearn to use ABS.
I was just hoping that I could use Arch since it is faster to install..
Last edited by Kabi (2008-07-14 09:08:14)

DSO 6032A KEYSIGHT SCOPE OLDER DRIVER

Similar Messages

Maybe you are looking for