DSP error -Calls getting disconnected

Jan 26 21:54:09.871: %DSPRM-5-SETCODEC: Configured codec 14 is not supported wit
h this dsp image.
Jan 26 21:54:16.323: %DSPRM-5-UPDOWN: DSP 7 in slot 1, changed state to up
I have this error on Cisco3745 which is configured as voice gateway.
Network:
Cisco 3745 is connected to PBX e1 cards using 2 Controller E1(NMHDV) QSIG.
Some of the calls made by agents are getting disconnected. This is a call center. I have huge no. of calls @ 25 calls dialed out in 10 seconds.
PBX vendor says disconnect message coming from Cisco which is connected by e1 pri.
About this error Cisco website says
""The %DSPRM-5-SETCODEC error is caused by having a high complexity codec configured on a VoIP dial-peer while still having the voice card set for the default of medium complexity""
http://www.cisco.com/en/US/tech/tk652/tk701/technologies_tech_note09186a00800b6710.shtml
But my Voice Class codec is this
voice class codec 100
codec preference 1 g729r8 bytes 40 - medium complexity only
codec preference 2 g723r63 bytes 48
codec preference 3 g723ar63 bytes 48
WHAT ELSE CAN BE THE PROBLEM.
How to FIX this guys.
Thx very much.

Hi
See this document:
http://www.cisco.com/en/US/tech/tk652/tk701/technologies_tech_note09186a00800b6710.shtml#code_com
According to this G723 is a high-complexity codec, so you'll need to have the 'codec complexity high' command under your voice-card...
You need to clear out the config of your E1 before changing the complexity.
Aaron

Similar Messages

Call gets disconnected after playing the menu from CVP

Hello,
When I make a call, the call is going to the ICM and then it is coming to the Call server then to the VXML gateway and then it goes to the VXML server and plays the promt.
The problem i am facing is that once the menu audio is played the call gets disconnected. It doesnt let me choose any options. I feel it is not able to identify the my inputs
I have some debug outputs
Mar 1 01:09:03.095: //-1/C113522D805A/CCAPI/cc_api_display_ie_subfields:
   cc_api_call_setup_ind_common:
   cisco-username=1000
   ----- ccCallInfo IE subfields -----
   cisco-ani=sip:[email protected]:5060
   cisco-anitype=0
   cisco-aniplan=0
   cisco-anipi=0
   cisco-anisi=1
   dest=sip:[email protected];transport=udp
   cisco-desttype=0
   cisco-destplan=0
   cisco-rdie=FFFFFFFF
   cisco-rdn=
   cisco-rdntype=0
   cisco-rdnplan=0
   cisco-rdnpi=-1
   cisco-rdnsi=-1
   cisco-redirectreason=-1   fwd_final_type =0
   final_redirectNumber =
   hunt_group_timeout =0
*Mar 1 01:09:03.103: //-1/C113522D805A/CCAPI/cc_api_call_setup_ind_common:
   Interface=0x67213130, Call Info(
   Calling Number=sip:[email protected]:5060,(Calling Name=)(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed),
   Called Number=sip:[email protected];transport=udp(TON=Unknown, NPI=Unknown),
   Calling Translated=FALSE, Subscriber Type Str=Un
R1#known, FinalDestinationFlag=TRUE,
   Incoming Dial-peer=811, Progress Indication=NULL(0), Calling IE Present=TRUE,
   Source Trkgrp Route Label=, Target Trkgrp Route Label=, CLID Transparent=FALSE), Call Id=65
*Mar 1 01:09:03.103: //-1/C113522D805A/CCAPI/ccCheckClipClir:
   In: Calling Number=sip:[email protected]:5060(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed)
*Mar 1 01:09:03.103: //-1/C113522D805A/CCAPI/ccCheckClipClir:
   Out: Calling Number=sip:[email protected]:5060(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed)
*Mar 1 01:09:03.103: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
*Mar 1 01:09:03.103: :cc_get_feature_vsa malloc success
*Mar 1 01:09:03.103: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
*Mar 1 01:09:03.103: cc_get_feature_vsa count is 1
*Mar 1 01:09:03.103: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
*Mar 1 01:09:03.103: :FEATURE_VSA attributes are: feature_name:0,feature_time:1732532552,feature_id:23
*Mar 1 01:09:03.103: //65/C113522D805A/CCAPI/cc_api_call_setup_ind_common:
   Set Up Event Sent;
   Call Info(Calling Number=(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed),
   Called Number=(TON=Unknown, NPI=Unknown))
*Mar 1 01:09:03.111: //65/C113522D805A/CCAPI/cc_process_call_setup_ind:
   Event=0x67452800
*Mar 1 01:09:03.119: //65/C113522D805A/CCAPI/ccCallSetContext:
   Context=0x65097114
*Mar 1 01:09:03.119: //65/C113522D805A/CCAPI/cc_process_call_setup_ind:
   >>>>CCAPI handed cid 65 with tag 811 to app "_ManagedAppProcess_bootstrap"
*Mar 1 01:09:03.143: //65/C113522D805A/CCAPI/ccCallProceeding:
   Progress Indication=NULL(0)
*Mar 1 01:09:03.147: //65/C113522D805A/CCAPI/ccCallConnect:
   Progress Indication=NULL(0), Data Bitmask=0x0
*Mar 1 01:09:03.151: //65/C113522D805A/CCAPI/ccCallConnect:
   Call Entry(Connected=TRUE, Responsed=TRUE)
*Mar 1 01:09:03.239: //65/C113522D805A/CCAPI/cc_api_event_indication:
   Event=141, Call Id=65
*Mar 1 01:09:03.243: //65/C113522D805A/CCAPI/cc_api_event_indication:
   Event Is Sent To Conferenced SPI(s) Directly
*Mar 1 01:09:03.243: //65/C113522D805A/CCAPI/cc_api_caps_ind:
   Destination Interface=0x0, Destination Call Id=-1, Source Call Id=65,
   Caps(Codec=0x0, Fax Rate=0x2, Vad=0x2,
   Modem=0x0, Codec Bytes=20, Signal Type=2)
*Mar 1 01:09:03.243: //65/C113522D805A/CCAPI/cc_api_caps_ind:
   Caps(Playout Mode=1, Playout Initial=60(ms), Playout Min=40(ms),
   Playout Max=250(ms), Fax Nom=300(ms))
*Mar 1 01:09:04.163: //65/C113522D805A/CCAPI/ccCallHandoff:
   Silent=FALSE, Application=0x6773AB4C, Conference Id=0xFFFFFFFF
*Mar 1 01:09:04.295: //65/C113522D805A/CCAPI/ccSetDigitTimeouts:
   Initial Digit Timeout=0(ms), Inter Digit Timeout=0(ms)
*Mar 1 01:09:04.295: //65/C113522D805A/CCAPI/ccSetDigitTimeouts:
   Call Entry(Inter Digit Timeout=0(ms), Initial Digit Timeout=0(ms))
*Mar 1 01:09:04.295: //65/xxxxxxxxxxxx/CCAPI/ccCallReportDigits:
   (callID=0x41, digit_event=0x1, enable=TRUE, consume=FALSE)
*Mar 1 01:09:04.299: //65/C113522D805A/CCAPI/ccCallReportDigits:
   Enabled=TRUE, Call Id=65
*Mar 1 01:09:04.303: //65/xxxxxxxxxxxx/CCAPI/cc_api_call_report_digits_done:
   (vdbPtr=0x67213130, callID=0x41, disp=-4, digit_event=0x1, enable=TRUE, consume=FALSE)
*Mar 1 01:09:04.307: //65/C113522D805A/CCAPI/cc_api_call_report_digits_done:
   Enabled=TRUE, Disposition=0xFFFFFFFC, Interface=0x67213130, Call Id=65
*Mar 1 01:09:04.311: //65/C113522D805A/CCAPI/cc_api_call_report_digits_done:
   Call Entry(Initial Digit Timeout=0(ms), Inter Digit Timeout=0(ms))
*Mar 1 01:09:05.291: //65/C113522D805A/CCAPI/ccAssociateStream:
   Coder=5, DTMF Relay=4, Vad=0,
   Record Function=0x0, Event Queue=0x66954714, Stream Context=678B0364,
   Record Context=0x0, Stream Call Id=66, Call Id=65
*Mar 1 01:09:05.295: //65/C113522D805A/CCAPI/ccAssociateStream:
   Call Entry(Stream Status=2, Digit Enable=TRUE)
*Mar 1 01:09:05.327: //65/C113522D805A/CCAPI/cc_api_call_associated:
   Interface=0x0, CallId=65, Disposition=0
   Play Function=0x62C2DFA8, Codec=0x5, Vad=0x0
   Media Type=0x3, SPI Context=0x678D2480, Stream CallId=66
   TX Dynamic Pt=0x0, RX Dynamic Pt=0x0
*Mar 1 01:09:05.531: //65/C113522D805A/CCAPI/ccSetDigitTimeouts:
   Initial Digit Timeout=5000(ms), Inter Digit Timeout=10000(ms)
*Mar 1 01:09:05.535: //65/C113522D805A/CCAPI/ccSetDigitTimeouts:
   Call Entry(Inter Digit Timeout=10000(ms), Initial Digit Timeout=5000(ms))
*Mar 1 01:09:05.535: //65/xxxxxxxxxxxx/CCAPI/ccCallReportDigits:
   (callID=0x41, digit_event=0x1, enable=TRUE, consume=FALSE)
*Mar 1 01:09:05.535: //65/C113522D805A/CCAPI/ccCallReportDigits:
   Enabled=TRUE, Call Id=65
*Mar 1 01:09:05.535: //65/xxxxxxxxxxxx/CCAPI/cc_api_call_report_digits_done:
   (vdbPtr=0x67213130, callID=0x41, disp=-4, digit_event=0x1, enable=TRUE, consume=FALSE)
*Mar 1 01:09:05.539: //65/C113522D805A/CCAPI/cc_api_call_report_digits_done:
   Enabled=TRUE, Disposition=0xFFFFFFFC, Interface=0x67213130, Call Id=65
*Mar 1 01:09:05.543: //65/C113522D805A/CCAPI/cc_api_call_report_digits_done:
   Call Entry(Initial Digit Timeout=5000(ms), Inter Digit Timeout=10000(ms))
*Mar 1 01:09:08.723: //65/C113522D805A/CCAPI/ccDisassociateStream:
   Record Context=0x0, Stream Call Id=66, Call Id=65
*Mar 1 01:09:08.723: //65/C113522D805A/CCAPI/ccDisassociateStream:
   Call Entry(Stream Status=1, Digit Enable=TRUE)
*Mar 1 01:09:08.735: //65/C113522D805A/CCAPI/ccAssociateStream:
   Coder=5, DTMF Relay=4, Vad=0,
   Record Function=0x0, Event Queue=0x66954714, Stream Context=678B0364,
   Record Context=0x0, Stream Call Id=66, Call Id=65
*Mar 1 01:09:08.739: //65/C113522D805A/CCAPI/ccAssociateStream:
   Call Entry(Stream Status=2, Digit Enable=TRUE)
*Mar 1 01:09:08.747: //65/C113522D805A/CCAPI/cc_api_call_associated:
   Interface=0x0, CallId=65, Disposition=0
   Play Function=0x62C2DFA8, Codec=0x5, Vad=0x0
   Media Type=0x3, SPI Context=0x678D2480, Stream CallId=66
   TX Dynamic Pt=0x0, RX Dynamic Pt=0x0
R1#
R1#
*Mar 1 01:09:16.143: //65/C113522D805A/CCAPI/ccDisassociateStream:
   Record Context=0x0, Stream Call Id=66, Call Id=65
*Mar 1 01:09:16.143: //65/C113522D805A/CCAPI/ccDisassociateStream:
   Call Entry(Stream Status=1, Digit Enable=TRUE)
*Mar 1 01:09:16.175: //65/C113522D805A/CCAPI/ccCallDisconnect:
   Cause Value=16, Tag=0x0, Call Entry(Previous Disconnect Cause=0, Disconnect Cause=0)
*Mar 1 01:09:16.179: //65/C113522D805A/CCAPI/ccCallDisconnect:
   Cause Value=16, Call Entry(Responsed=TRUE, Cause Value=16)
*Mar 1 01:09:16.227: //65/C113522D805A/CCAPI/cc_api_call_disconnect_done:
R1#Disposition=0, Interface=0x67213130, Tag=0x0, Call Id=65,
   Call Entry(Disconnect Cause=16, Voice Class Cause Code=0, Retry Count=0)
*Mar 1 01:09:16.235: //65/C113522D805A/CCAPI/cc_api_call_disconnect_done:
   Call Disconnect Event Sent
*Mar 1 01:09:16.235: //-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
*Mar 1 01:09:16.235: :cc_free_feature_vsa freeing 67445940
*Mar 1 01:09:16.235: //-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
*Mar 1 01:09:16.235: vsacount in free is 0
I have some basic VXML gateway configuration
R1#show run
Building configuration...
Current configuration : 2588 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname R1
boot-start-marker
boot-end-marker
no aaa new-model
memory-size iomem 5
ip cef
no ip domain lookup
ip domain name lab.local
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
multilink bundle-name authenticated
voice service voip
sip
header-passing
application
service cvperror flash:cvperror.tcl
paramspace english index 0
paramspace english language en
paramspace english location flash
paramspace english prefix en
service new-call flash:bootstrap.vxml
paramspace english index 0
paramspace english language en
paramspace english location flash
paramspace english prefix en
service ringtone flash:ringtone.tcl
paramspace english language en
paramspace english index 0
paramspace english location flash
paramspace english prefix en
service ringback flash:ringtone.tcl
service handoff flash:handoff.tcl
paramspace english index 0
paramspace english language en
paramspace english location flash
paramspace english prefix en
service bootstrap flash:bootstrap.tcl
paramspace english index 0
paramspace english language en
paramspace english location flash
paramspace english prefix en
archive
log config
hidekeys
interface FastEthernet0/0
ip address 192.168.1.253 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
ip forward-protocol nd
no ip http server
no ip http secure-server
control-plane
dial-peer voice 9191 voip
service ringtone
session protocol sipv2
incoming called-number 91919191
codec g711ulaw
no vad
dial-peer voice 9292 voip
service cvperror
session protocol sipv2
incoming called-number 92929292
codec g711ulaw
no vad
dial-peer voice 1503 voip
destination-pattern 1503
session protocol sipv2
session target ipv4:192.168.1.57
dtmf-relay rtp-nte h245-alphanumeric h245-signal
codec g711ulaw
ip qos dscp cs3 signaling
no vad
dial-peer voice 100 voip
destination-pattern 10..
session target ipv4:192.168.1.100
dial-peer voice 811 voip
service bootstrap
session protocol sipv2
session target sip-server
incoming called-number 81T
codec g711ulaw
no vad
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous
line aux 0
exec-timeout 0 0
privilege level 15
logging synchronous
line vty 0 4
login
end
Please help me out how o fix this issue/

Thanks for the respose
The microapp what I use is user.microapp.ToExtVXML[]
This is the activity log in the CVP application. I dont see any error logs.
192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.109,,start,newcall,
192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.109,,start,ani,NA
192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.109,,start,areacode,NA
192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.109,,start,exchange,NA
192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.109,,start,dnis,NA
192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.109,,start,uui,NA
192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.109,,start,iidigits,NA
192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.125,CVP Subdialog Start_01,enter,
192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.593,CVP Subdialog Start_01,exit,done
192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.593,Greetings,enter,
192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.597,Greetings,interaction,audio_group,initial_audio_group
192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.703,Greetings,exit,done
192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.703,Menu,enter,
192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.707,Menu,interaction,audio_group,initial_audio_group
192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.875,Menu,exit,
192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.875,,end,how,hangup
192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.875,,end,result,normal
192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.875,,end,duration,1
192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.531,,start,newcall,
192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.531,,start,ani,NA
192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.531,,start,areacode,NA
192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.531,,start,exchange,NA
192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.531,,start,dnis,NA
192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.531,,start,uui,NA
192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.531,,start,iidigits,NA
192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.531,CVP Subdialog Start_01,enter,
192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.921,CVP Subdialog Start_01,exit,done
192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.921,Greetings,enter,
192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.957,Greetings,interaction,audio_group,initial_audio_group
192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:07.109,Greetings,exit,done
192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:07.109,Menu,enter,
192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:50:25.718,,end,how,app_session_complete
192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:50:25.718,,end,result,timeout
192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:50:25.718,,end,duration,1819
192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.312,,start,newcall,
192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.312,,start,ani,NA
192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.312,,start,areacode,NA
192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.312,,start,exchange,NA
192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.312,,start,dnis,NA
192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.312,,start,uui,NA
192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.312,,start,iidigits,NA
192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.312,CVP Subdialog Start_01,enter,
192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.750,CVP Subdialog Start_01,exit,done
192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.750,Greetings,enter,
192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.782,Greetings,interaction,audio_group,initial_audio_group
192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.937,Greetings,exit,done
192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.937,Menu,enter,
192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:53:25.718,,end,how,app_session_complete
192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:53:25.718,,end,result,timeout
192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:53:25.718,,end,duration,1829
Thank you

Calls Getting disconnected with reason code 26

Hi,
Few of my calls are getting disconnected with reason code 26. on agent screen it just flash and disconnect.as per RCD its showing Error code 0( fine) and finally its ending at Skill Group Node. talk time is 1 or 2 seconds. agents having auto answer setting as well as IP Phone set auto ans with headset.
my setup is IPIVR based UCCE setup.
Please help
Regards-
PK

Hi PK,
CD 26 normally indicates Resource Not available in CUCM side. please check the Jtapi gateway process logs for the failed calls. you should be able to see something similar to below
19:08:37:896 PG1A-jgw1 Trace: ConnFailedEv CID: 27224748 Addr: 80002985 CiscoCause: CAUSE_RESOURCESNAVAIL Cause: CAUSE_RESOURCES_NOT_AVAILABLE.
if that is the case , please check from CUCM perspective as well.
Regards,
Sasikumar.

Calls getting disconnected in my Nokia XL within 1...

Hi,
All my calls which I am making or recieving are getting disconnected within 1 minute in my Nokia XL. Please help with solution for this problem

How old is your sim card and have you spoke to your provider?
If i have helped at all a click on the white star below would be nice thanks.
Now using the Lumia 1520

Call gets disconnected when lock button is pressed.

I use iPhone 6 and upgraded my device to 8.3 today. This happened to me couple of times now, I was in a call without a hands free got a text message , the screen lit up with notification and never got switched off. Now ow when I pressed on a lock button to lock the screen and continue on call , the call got disconnected .
This is very wiered. Any comments on this.?????

Sounds like you have a internal connection problem in the iPod. I would make an appointment at the Genius Bar of a local Apple store.

When calls get disconnected, call timer does not s...

I have had European unlimited account for several years, for the past couple of months when calling land lines the number rings, the number is answered and the line goes dead, the timer on the phone continues to increase, I have the same problem using either my dual skype phones (no pc) or using either of my iPhones, some s recalling the same number its answered and all is OK, its impossible to contact skype by email for help, the site just sends me around in circles but no contact made available to email any one.
This post was transferred from its previous location to create its own new topic here; its subject and/or title has been edited to differentiate the post from other inquiries and to reflect the post's content.

Ring/Silent switch on?

I noticed that Phone call, is getting disconnected often while on the wheel.

Any one have noticed this problem while using your iPhone:
While you are travelling (on the wheel) and attending a phone call, while your the cell phone receives signal from telecom network tower to tower, your phone call get disconnected automatically. When you look at you phone, it shows there is no network and after sometime (about 2 to 4 Seconds) phone receives signal back.
I am using iPhone 3GS model with iOS 6.1.3 (10B329). I thought this would be my phone problem but when I asked my friends and colleagues (they are using iPhone 5) and they said that even they are facing this issue.
Another issue: Today we (a group) in a club house. We kept 3 iPhones, 1 Nokia phone and a Samsung phone in a line. iPhone receives only 1 network tower (3G) while both the phones (Nokia and Samsung) receives 4 towers out of 5. Where we all use the same network provider (Corporate connection).
Then what we 3 did is we Switched ON the Airplane Mode and after a while switched OFF this mode. After that iPhone start to receive the full signal.
What is this PROBLEM in iPhone ? What about you (iPhone users) did you face this problem ?
What is the solution ? Any answer ......

It sounds like the vibration motor on your iPhone has failed and will no longer vibrate.

The signal of carrier vodafone and idea fluctuates and call get intermittent disrupted voice what to do?

Call getting disconnected and voice to is disrupted why?

Parkash,
You better rely on nokia website repair option. UPS tracking is only one sided job, and once they delivered it to nokia service centre, their job is done.
Now it is very confusing, they have 2 ware house, according to their manager. All phones which go for repair, get delivered to 1st warehouse, where it stays for couple of day, they open it and then send it to 2nd warehouse which is proper repair centre.
Once your phone is repaird, you will get e-mail from nokia that your phone is ready for pick up from local service centre (just ignore that e-mail).
This e-mail is sent to you when your phone is ready in 2nd ware house (repair centre), and it may take 3-7 days after that to get delivered to you. It has to go to first warehouse, and they dispatch it 1-3 days after that e-mail.
I think if nokia repair service is showing that it is being repaired, than its still in their repair house. Mine one took 2 weeks and 4 days before I get e-mail that it is ready for pick up.
It took another 2 weeks to track it, as they did not provide my contact number to UPS whereas UPS tried on 3 ocassions to deliver it to me and (as I live in intercom controlled flats) so they could not even leave notice.
Finally complaining to Nokia thourgh their nokia care centre helpline, speaking to their manager and getting time fram of 24-48 hours, nothing happend. Got call in 72 hours from UK to give me new tracking number and I was told that UPS tried to contact you.
Anyhow after getting in touch with UPS and get it delieved to my office I noticed that there was no phone number....
There you go, everthing get lost in the system, especially when they are big corporate giant companies.
Best of luck mate. Keep us updated with the progress.

Phone gets Disconnected

I have z3 dual sim. I use my main sim which is used for voice calls in sim 1 and data sim for Internet in sim 2.
The first.problem i am facing is that i cannot set sim 1 as the default sim for voice calling.each time i have to select sim.
The next issue is whenever my voice conversation exceeds more that 2 to 3 minutes, the call gets Disconnected. Sometimes in less than one minute too. I tried to disable the sim 2 or disable mobile network, at this time no issues. The calls goes on. I have faced this issue on my old Samsung dual sim too. Can i get the solution for both problems

yep. it happens to me on iPhone 5 with iOS 6.0. I have yet found a solution. If you do search in this discussion forum, you will see a lot of discussion regarding the same topic on iOS 6/6.0.1 on iPhone 4/4s/5
https://discussions.apple.com/thread/4487915?tstart=0

Spa400 firmware 1.0.1.3 drops calls - DSP errors

spa400 firmware 1.0.1.3 is not reliable enough for production use, since it is frequently dropping calls mid-conversation. syslog trace suggests its internal DSP software is falling over: Mar 13 14:33:47 spa400 0045173199 - DIM: 0:*, DSP ERROR: Reason= Exception 0x1DAE ^M Mar 13 14:33:47 spa400 0045173199 - DSP: 0:*, ALARM= Software exception (bits=8 numeric=1795)^M Mar 13 14:33:47 spa400 0045173250 - DSP 0 Failure. Error: 3^M Mar 13 14:33:47 spa400 0045173254 - CCU: 2, Channel Failure. State: 6^M Mar 13 14:33:47 spa400 0045173258 - CCU: 1, Channel Failure. State: 6^M Mar 13 14:33:47 spa400 0045173258 - CCU: 3, Channel Failure. State: 6^M Mar 13 14:33:47 spa400 0045173258 - CCU: 0, Channel Failure. State: 6^M Mar 13 14:33:47 spa400 0045173259 - SPU: 2, Coding failure^M Mar 13 14:33:47 spa400 0045173259 - SPU: 1, Coding failure^M Mar 13 14:33:47 spa400 0045173259 - SPU: 3, Coding failure^M Mar 13 14:33:47 spa400 0045173263 - SPU: 0, Coding failure^M Mar 13 14:33:47 spa400 0045173263 - DIM: channel_config2 TCID 0 has no DSP^M Mar 13 14:33:47 spa400 0045173264 - EXT CPS: EXTENDED collect - Failed CCU Reconfigure on tcid 0 ^M Mar 13 14:33:47 spa400 0045173264 - DIM: channel_config2 TCID 0 has no DSP^M Mar 13 14:33:58 spa400 0045178527 - George: Set UK CID on 2^M Mar 13 14:33:58 spa400 0045178527 - DIM: voice_config2 TCID 2 has no DSP^M Mar 13 14:33:58 spa400 0045178527 - DIM: voice_config2 TCID 2 has no DSP^M Mar 13 14:33:58 spa400 0045178770 - DIM: , CHECKSUM=49159^M Mar 13 14:33:58 spa400 0045178773 - DIM: 0:*, Core Download complete!^M Mar 13 14:33:58 spa400 0045178773 - DIM: 0:*,Writing 0x6a001400 @ 0x100^M Mar 13 14:33:58 spa400 0045178775 - DIM: 0:*, CONFIG has been received!^M Mar 13 14:34:20 spa400 0045189591 - George: Set UK CID on 1^M Mar 13 14:34:20 spa400 0045189591 - DIM: voice_config2 TCID 1 has no DSP^M Mar 13 14:34:20 spa400 0045189592 - DIM: voice_config2 TCID 1 has no DSP^M Mar 13 14:34:20 spa400 0045189594 - George: Set UK CID on 3^M Mar 13 14:34:20 spa400 0045189594 - DIM: voice_config2 TCID 3 has no DSP^M Mar 13 14:34:20 spa400 0045189594 - DIM: voice_config2 TCID 3 has no DSP^M I'm sure other people have hit this too. Linksys guys - can you fix it?

thanks for this info...i haven't had time to check on my syslog trace ever sicne I've upgraded to the latest firmware and i haven't been using the SPA400 that much lately...if i find some time I will post my trace here as well in case i get the same problem
i suggest using firmware version 1.0.1.1 in the meantime if your problem only started after you upgraded to the latest firmware
| isolate! isolate! isolate! |

Why do calls on my iPhone 5 keep getting disconnected at random intervals?

My iPhone 5 is in a cover. Most of the time when I answer a call, it gets disconnected. Once, a person had to call me back 11 times! Is there something wrong with my iPhone? Why do calls (both outgoing and incoming) keep getting disconnected at random intervals?

Hi, could be an error, if you back up your data and perform a reset to factory standard could sort it. But before doing this, explore the settings for sounds and vibration patterns see if there are different settings selected by mistake. hope this helps

HT4245 i use a macbook pro which came with facetime i have an iphone 4S as well. whenever i use the wireless on my iphone i can facetime with ease however when i use the same wireless for my mac to facetime the call always gets disconnected.

i use a macbook pro which came with facetime i have an iphone 4S as well. whenever i use the wireless on my iphone i can facetime with ease however when i use the same wireless for my mac to facetime the call always gets disconnected.

To use factime on your Mac, I believe you will need to use your email address to do so instead of your wireless number. Since you can't make calls on the Mac.

Getting Fatal error: Call to undefined function mysql_connect() error.

ok, so before I had my mysql_connect php script and it ran fine, no errors, but once I changed my php.ini file to give ERROR_REPORTING E_ALL I now get Fatal error: Call to undefined function mysql_connect(). I am just wondering how I can fix this?
I followed the arch linux LAMP wiki and I can't figure out why I am getting this error after turnning on error_reporting.
Thanks
this is my php code
<?php
$connection = mysql_connect('localhost', 'root', 'password');
if(!$connection){
echo mysql_error();
} else {
echo 'connected';
if (!mysql_select_db('my_first_db')){
echo 'uh';
} else {
echo 'selected database';
?>
<?php phpinfo(); ?>
Last edited by clandest (2012-03-22 04:36:43)

aking9 wrote:grabbing into the back of the back of my memory here but don't you need to specify a port to connect to?
Only if you change the port from the default 3306. But even then, a different error message will output, in this case the mysql modules have not loaded for some reason.
There is a syntax error in your php.ini file, at line 510. Comment out this line as it's a line giving information rather than an option. Then uncomment the error_reporting option.
So this:
Default Value: E_ALL & ~E_NOTICE
; Development Value: E_ALL | E_STRICT
; Production Value: E_ALL & ~E_DEPRECATED
; http://php.net/error-reporting
;error_reporting = E_ALL & ~E_DEPRECATED
Should be changed to this:
; Default Value: E_ALL & ~E_NOTICE
; Development Value: E_ALL | E_STRICT
; Production Value: E_ALL & ~E_DEPRECATED
; http://php.net/error-reporting
error_reporting = E_ALL & ~E_DEPRECATED
After this try "sudo /etc/rc.d/httpd restart" then see if you have any better luck connecting to mysql.
Last edited by astiak (2012-03-22 23:24:40)

Getting a error when Muse Website is viewed in browser:MuseJSAssert: Error calling selector function

Every time I open any .html file in a browser I recieve this error message; MuseJSAssert: Error calling selector function: TypeError: Object does'nt support property or method 'museMenu'

I have a similar problem that seems to have come up since the latest upgrade. My error is:
"JavaScript Alert
MuseJSAssert: Error calling selector function:SecurityError:Blocked a frame with origin "null" from accessing a cross-origin frame."
The strange part for me is that there's no error at all when using File>Preview Page in Browser. I only get the error when I File>Export Page as HTML and then try to view the output.
I can post a zip file of the HTML output to Adobe, but not publicly. Also, where is the Preview Page stored? If I don't get error on that, why can't I just use that as my HTML output?
Thanks!

Problem calling web service: Error while getting the ORACLE user account

Hi All!
I was able to call the service EGO_ITEM_PUB-PROCESS_ITEM, but after implemented some patches, suddenly I get this error as result:
- <env:Envelope xmlns:env="http://schemas.xmlsoap.org/soap/envelope/">
- <env:Body>
- <OutputParameters xmlns="http://xmlns.oracle.com/apps/ego/soaprovider/plsql/ego_item_pub/process_item__1/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
<X_INVENTORY_ITEM_ID xsi:nil="true" />
<X_ORGANIZATION_ID xsi:nil="true" />
<X_RETURN_STATUS>U</X_RETURN_STATUS>
<X_MSG_COUNT>1</X_MSG_COUNT>
<X_MSG_DATA>Encountered an error while getting the ORACLE user account for your concurrent request. Contact your system administrator.</X_MSG_DATA>
</OutputParameters>
</env:Body>
</env:Envelope>
Any ideas?
Thanks,
Konrad

hsawwan wrote:
Hi,
I was able to call the service EGO_ITEM_PUB-PROCESS_ITEM, but after implemented some patches, What are those patches?
# Patch 8407693:R12.TXK.B ISG: Service Generation Failure - Java Compiler Could Not be Found
# Patch 8459663:R12.OWF.B : Mandatory Consolidated One-Off Fixes for ISG on Top of 12.1.1
# Patch 8916358:R12.OWF.B : Service Timeout When Invoking Services Deployed to Integrated SOA Gateway
# Patch 9349321:R12.OWF.B : Issue with item Bulk Load in Oracle Product Hub PIP 2.4
# Patch 9446625:R12.FND.B : 1OFF:8995921:12.1.1:12.1.1:PERF : LoginModules Performance Issue
# Patch 9070077:R12.OWF.B : 1OFF:9045280:12.1.1:12.1.1:Invoking a Web Service Requires NLS Lang When It Should be Optional
# Patch 9153106:R12.OWF.B : IREP_Parser.PL Exits with GETPWUID Function IS Unimplemented in PARSER.PM -> Wichtig für ISG (für custom pl/sqls im ISG)
# Patch 9004712:R12.OWF.B : One-Off for IREP PARSER on Top of Oracle E-Business Suite Release 12.1.1 -> Wichtig für ISG (für custom pl/sqls im ISG)
IAS:
# Patch 8607523 for the AS version 10.1.3.4
Oracle Support told me that I need this patches because of some other problem (generating wsdl and deploy for BOM_BO_PUB package does not work in my environment) and since that, the process_item call stopped working!
btw: The EGO_ITEM_PUB-PROCESS_ITEM call for an existing item still works (I can modify the description), but creating a new item does not work anymore. Here are the parameters I send to the web service:
Header:
<wsse:Security xmlns:wsse="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-secext-1.0.xsd">
<wsse:UsernameToken>
<wsse:Username>sysadmin</wsse:Username>
<wsse:Password
Type="http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-username-token-profile-1.0#PasswordText">sysadmin</wsse:Password>
</wsse:UsernameToken>
</wsse:Security>
<q0:SOAHeader/>
Body:
<q1:InputParameters>
<q1:P_API_VERSION>1.0</q1:P_API_VERSION>
<q1:P_INIT_MSG_LIST>T</q1:P_INIT_MSG_LIST>
<q1:P_COMMIT>T</q1:P_COMMIT>
<q1:P_TRANSACTION_TYPE>CREATE</q1:P_TRANSACTION_TYPE>
<q1:P_ITEM_NUMBER>KHR_WS_05</q1:P_ITEM_NUMBER>
<q1:P_DESCRIPTION>desc2</q1:P_DESCRIPTION>
</q1:InputParameters>
Thanks,
Konrad

DSP error -Calls getting disconnected

Similar Messages

Maybe you are looking for