DSP Resource for VIC3-4FXS/DID on NM-HDV2
Hi,
If only PVDM3 is installed on the C3945 motherboard (Slot 0), and I have VIC3-4FXS/DID inserted in the NM-HDV2 and but without PVDM2 installed in the NM-HDV2, can I still enable the FXS port?
Do I need to have this command to enable dsp sharing with the NM-HDV2?
voice-card 1
dsp tdm pooling
Also, should the FXS ports appear in the "show voice port summary"?
Thank you.
Hi,
just refer this
http://www.cisco.com/c/en/us/products/interfaces-modules/2800-3800-high-density-packet-voice-digital-signal-processor/index.html
Are the PVDM3 modules supported in a NM-HDV2?
A. No. You cannot install PVDM3 modules directly on the PVDM slots of an NM-HDV2, only the PVDM2s are
supported by the NM-HDV2. However, an NM-HDV2 that has no PVDMs installed at all can share PVDM3 DSP
resources from the router motherboard PVDM slots across the chassis backplane.
Q. Do the PVDM2 modules work with the Cisco 2900 and 3900 Series platforms?
A. Yes. You can install PVDM2 modules on the motherboard PVDM slots using special adaptor cards (PVDM2-
ADPTR). You can also insert an NM-HDV2 module with PVDM2 modules into the service-module slot of the
Cisco 2900 and 3900 Series platforms using the network-to-server module adaptor card (SM-NM-ADPTR).
regds,
aman
Similar Messages
-
Why the ringing voltage closely 0v for VIC3-2FXS/DID port?
Initially, I have tested every port of FXS module on ISR with an analog phone. There
was ringing tone and I was able to communicate to other as normal. The second
test involved measuring the ringing voltage on the same ports by using a pair cable and multimeter. The
'idle voltage' measured was around 44V and when there was an incoming call, the measured 'ringing
voltage' was close to 0V.
So why the ringing voltage is drop to 0V?
Please advice.You cannot measure ringing voltage with a common multimeter. Read why:
http://www.sandman.com/ringvoltbul.html -
VIC3-4FXO/DID module not detect in 2801 Router.
Hi Team,
I have Cisco 2801 router with 2 DSP 16 Channel, 128 MB DRAM and 128 MB flash. I am using IOS c2801-spservicesk9-mz.124-3i but the VIC3-4FXO/DID module is not detected. I tried to upgrade the IOS to 15.0 and 15.1 but the router is not boot up due to insufficient memory. In that IOS the FXO card is detected. I checked the data sheet of both router and FXO card it support 12.4T IOS but when I upload the IOS and try to boot same problem I have faced (router not boot due to insufficient memory). Kindly help me find out the appropriate IOS to resolve the issue.
Thanks in advance.
Regards,
Manas RanjanVIC3-4FXO card is not supported in 2801 according to table4
Table 4. Software and Memory Requirements for Voice/Fax Network Modules and Voice Interface Cards
Product
Cisco 2800 Series
Cisco 3800 Series
Cisco 2900 and 3900 Series
NM-HD-1V
NM-HD-2V
NM-HD-2VE
• Cisco IOS Software
• Release 12.3(8)T4
• "IP Voice" images
• Cisco IOS Software
• Release 12.3(11)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images
VIC2-2FXO
VIC2-4FXO
VIC2-2BRI-NT/TE
• Cisco IOS Software
• Release 12.3(8)T4
• "IP Voice" images
• Cisco IOS Software
• Release 12.3(11)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images
VWIC2-xMFT-xx
• Cisco IOS Software
• Release 12.3(14)T
• "IP Voice" images
• Cisco IOS Software
• Release 12.3(14)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images
VIC3-2E/M
• Cisco IOS Software
• Release 12.4(15)XW or 12.4(20)T
• "IP Voice" images
• Cisco IOS Software
• Release 12.4(15)XW or 12.4(20)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images
VIC3-2FXS/DID
VIC3-2FXS-E/DID
VIC3-4FXS/DID
• Cisco IOS Software
• Release 12.4(15)XZ or 12.4(20)T
• "IP Voice" images
• Cisco IOS Software
• Release 12.4(15)XZ or 12.4(20)T
• "IP Voice" images
• Cisco IOS Software Release 15.0(1)M
• "UC Technology" images -
I have a network in Beijing China below,
(1) E1 Pri interface to PSTN
(2) Vic3-2FXS/DID to fax machine
all these modules installed on Cisco 2900, when I call my fax machine from PSTN, the fax machine answered, but fax can't start.
I want to know is there any special consideration about the fax configuration to be worked.
Thanks for your advice.
Robert
2011/2/18Hey Robert.
Since you have PRI and the fxs port on the same card, in theory there is not a whole lot you need to do with regards to the fax or port configuration on the router if this is H323 or SIP. On our initial voip gateways even on port to port calls we would invoke fax relay, but on the ISR line with the internal tdm backplane, the dsp should be dropped from the call with minimal impairment of the connection through the gateway.
Now, this is true as long as you don't have "no local-bypass' configured under the voice-card. Default is that this is not configured but it you do, you should change it to local-bypass. "show voice dsp active" will show if the dsp is still in the loop on the call as well.
Definitely check the E1 controller ("show controller e1") for slips and errors. This will kill a fax if present.
Looking back at your previous post though, I would not expect you to be seeing G722 on the output of the show voice call summary when the call connects between the two ports.
Are you using MGCP?
When the call is active between the two ports, what is the output of "show call active voice brief" and "show call active fax brief"?
There are a few good resources for troubleshooting fax issues. An excellent source if the CiscoPress publication "Fax, Modem and Text for IP Telephony". If you would like some of the scaled down versions, I have posted a couple of links that would be useful.
Bryan
https://supportforums.cisco.com/community/netpro/collaboration-voice-video/ip-telephony/blog/2010/10/26/fax-configuration-and-troubleshooting-project
http://www.cisco.com/en/US/docs/ios/12_3/vvf_c/voice_troubleshooting/old/vts_fax.html -
Hi All,
We are on Netweaver 7.01 SP14. (well I understand we are way behind patch levels, but a simple file upload should be working ?/)
We are trying to upload (HTML &/ Image) a file in one of the KM's public folder.
As and when we select folder and click on upload we get the below message:
Below is the error trace details:
Full Message Text
com.sapportals.wdf.WdfException
at com.sapportals.wcm.control.edit.ResourceUploadControl.render(ResourceUploadControl.java:688)
at com.sapportals.wdf.layout.HorizontalLayout.renderControls(HorizontalLayout.java:42)
at com.sapportals.wdf.stack.Pane.render(Pane.java:155)
at com.sapportals.wdf.stack.PaneStack.render(PaneStack.java:73)
at com.sapportals.wdf.layout.HorizontalLayout.renderPanes(HorizontalLayout.java:73)
at com.sapportals.wdf.stack.Pane.render(Pane.java:158)
at com.sapportals.wdf.stack.PaneStack.render(PaneStack.java:73)
at com.sapportals.wdf.layout.HorizontalLayout.renderPanes(HorizontalLayout.java:73)
at com.sapportals.wdf.stack.Pane.render(Pane.java:158)
at com.sapportals.wdf.stack.PaneStack.render(PaneStack.java:73)
at com.sapportals.wdf.layout.HorizontalLayout.renderPanes(HorizontalLayout.java:73)
at com.sapportals.wdf.stack.Pane.render(Pane.java:158)
at com.sapportals.wdf.stack.PaneStack.render(PaneStack.java:73)
at com.sapportals.wdf.WdfCompositeController.internalRender(WdfCompositeController.java:709)
at com.sapportals.wdf.WdfCompositeController.buildComposition(WdfCompositeController.java:674)
at com.sapportals.htmlb.AbstractCompositeComponent.preRender(AbstractCompositeComponent.java:33)
at com.sapportals.htmlb.Container.preRender(Container.java:120)
at com.sapportals.htmlb.Container.preRender(Container.java:120)
at com.sapportals.htmlb.Container.preRender(Container.java:120)
at com.sapportals.portal.htmlb.PrtContext.render(PrtContext.java:408)
at com.sapportals.htmlb.page.DynPage.doOutput(DynPage.java:238)
at com.sapportals.wcm.portal.component.base.KMControllerDynPage.doOutput(KMControllerDynPage.java:134)
at com.sapportals.htmlb.page.PageProcessor.handleRequest(PageProcessor.java:133)
at com.sapportals.portal.htmlb.page.PageProcessorComponent.doContent(PageProcessorComponent.java:134)
at com.sapportals.wcm.portal.component.base.ControllerComponent.doContent(ControllerComponent.java:88)
at com.sapportals.portal.prt.component.AbstractPortalComponent.serviceDeprecated(AbstractPortalComponent.java:209)
at com.sapportals.portal.prt.component.AbstractPortalComponent.service(AbstractPortalComponent.java:114)
at com.sapportals.portal.prt.core.PortalRequestManager.callPortalComponent(PortalRequestManager.java:328)
at com.sapportals.portal.prt.core.PortalRequestManager.dispatchRequest(PortalRequestManager.java:136)
at com.sapportals.portal.prt.core.PortalRequestManager.dispatchRequest(PortalRequestManager.java:189)
at com.sapportals.portal.prt.component.PortalComponentResponse.include(PortalComponentResponse.java:215)
at com.sapportals.portal.prt.pom.PortalNode.service(PortalNode.java:645)
at com.sapportals.portal.prt.core.PortalRequestManager.callPortalComponent(PortalRequestManager.java:328)
at com.sapportals.portal.prt.core.PortalRequestManager.dispatchRequest(PortalRequestManager.java:136)
at com.sapportals.portal.prt.core.PortalRequestManager.dispatchRequest(PortalRequestManager.java:189)
at com.sapportals.portal.prt.core.PortalRequestManager.runRequestCycle(PortalRequestManager.java:753)
at com.sapportals.portal.prt.connection.ServletConnection.handleRequest(ServletConnection.java:249)
at com.sapportals.portal.prt.dispatcher.Dispatcher$doService.run(Dispatcher.java:557)
at java.security.AccessController.doPrivileged(Native Method)
at com.sapportals.portal.prt.dispatcher.Dispatcher.service(Dispatcher.java:430)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.runServlet(HttpHandlerImpl.java:401)
at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.handleRequest(HttpHandlerImpl.java:266)
at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:386)
at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:364)
at com.sap.engine.services.httpserver.server.RequestAnalizer.invokeWebContainer(RequestAnalizer.java:1064)
at com.sap.engine.services.httpserver.server.RequestAnalizer.handle(RequestAnalizer.java:265)
at com.sap.engine.services.httpserver.server.Client.handle(Client.java:95)
at com.sap.engine.services.httpserver.server.Processor.request(Processor.java:175)
at com.sap.engine.core.service630.context.cluster.session.ApplicationSessionMessageListener.process(ApplicationSessionMessageListener.java:33)
at com.sap.engine.core.cluster.impl6.session.MessageRunner.run(MessageRunner.java:41)
at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37)
at java.security.AccessController.doPrivileged(Native Method)
at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:104)
at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:176)
--- Nested WDF Exception -----------------------
java.util.MissingResourceException: Can't find resource for bundle java.util.PropertyResourceBundle, key xtlt_Required
at java.util.ResourceBundle.getObject(ResourceBundle.java:327)
at java.util.ResourceBundle.getObject(ResourceBundle.java:324)
at java.util.ResourceBundle.getString(ResourceBundle.java:287)
at com.sapportals.wcm.util.resource.ResourceBundles.getString(ResourceBundles.java:55)
at com.sapportals.wcm.control.base.WcmBaseControl.getBaseBundleString(WcmBaseControl.java:150)
at com.sapportals.wcm.control.base.WcmBaseControl.getBaseBundleString(WcmBaseControl.java:176)
at com.sapportals.wcm.control.edit.ResourceUploadControl.renderUploadFileContent(ResourceUploadControl.java:773)
at com.sapportals.wcm.control.edit.ResourceUploadControl.render(ResourceUploadControl.java:655)
at com.sapportals.wdf.layout.HorizontalLayout.renderControls(HorizontalLayout.java:42)
at com.sapportals.wdf.stack.Pane.render(Pane.java:155)
at com.sapportals.wdf.stack.PaneStack.render(PaneStack.java:73)
at com.sapportals.wdf.layout.HorizontalLayout.renderPanes(HorizontalLayout.java:73)
at com.sapportals.wdf.stack.Pane.render(Pane.java:158)
at com.sapportals.wdf.stack.PaneStack.render(PaneStack.java:73)
at com.sapportals.wdf.layout.HorizontalLayout.renderPanes(HorizontalLayout.java:73)
at com.sapportals.wdf.stack.Pane.render(Pane.java:158)
at com.sapportals.wdf.stack.PaneStack.render(PaneStack.java:73)
at com.sapportals.wdf.layout.HorizontalLayout.renderPanes(HorizontalLayout.java:73)
at com.sapportals.wdf.stack.Pane.render(Pane.java:158)
at com.sapportals.wdf.stack.PaneStack.render(PaneStack.java:73)
at com.sapportals.wdf.WdfCompositeController.internalRender(WdfCompositeController.java:709)
at com.sapportals.wdf.WdfCompositeController.buildComposition(WdfCompositeController.java:674)
at com.sapportals.htmlb.AbstractCompositeComponent.preRender(AbstractCompositeComponent.java:33)
at com.sapportals.htmlb.Container.preRender(Container.java:120)
at com.sapportals.htmlb.Container.preRender(Container.java:120)
at com.sapportals.htmlb.Container.preRender(Container.java:120)
at com.sapportals.portal.htmlb.PrtContext.render(PrtContext.java:408)
at com.sapportals.htmlb.page.DynPage.doOutput(DynPage.java:238)
at com.sapportals.wcm.portal.component.base.KMControllerDynPage.doOutput(KMControllerDynPage.java:134)
at com.sapportals.htmlb.page.PageProcessor.handleRequest(PageProcessor.java:133)
at com.sapportals.portal.htmlb.page.PageProcessorComponent.doContent(PageProcessorComponent.java:134)
at com.sapportals.wcm.portal.component.base.ControllerComponent.doContent(ControllerComponent.java:88)
at com.sapportals.portal.prt.component.AbstractPortalComponent.serviceDeprecated(AbstractPortalComponent.java:209)
at com.sapportals.portal.prt.component.AbstractPortalComponent.service(AbstractPortalComponent.java:114)
at com.sapportals.portal.prt.core.PortalRequestManager.callPortalComponent(PortalRequestManager.java:328)
at com.sapportals.portal.prt.core.PortalRequestManager.dispatchRequest(PortalRequestManager.java:136)
at com.sapportals.portal.prt.core.PortalRequestManager.dispatchRequest(PortalRequestManager.java:189)
at com.sapportals.portal.prt.component.PortalComponentResponse.include(PortalComponentResponse.java:215)
at com.sapportals.portal.prt.pom.PortalNode.service(PortalNode.java:645)
at com.sapportals.portal.prt.core.PortalRequestManager.callPortalComponent(PortalRequestManager.java:328)
at com.sapportals.portal.prt.core.PortalRequestManager.dispatchRequest(PortalRequestManager.java:136)
at com.sapportals.portal.prt.core.PortalRequestManager.dispatchRequest(PortalRequestManager.java:189)
at com.sapportals.portal.prt.core.PortalRequestManager.runRequestCycle(PortalRequestManager.java:753)
at com.sapportals.portal.prt.connection.ServletConnection.handleRequest(ServletConnection.java:249)
at com.sapportals.portal.prt.dispatcher.Dispatcher$doService.run(Dispatcher.java:557)
at java.security.AccessController.doPrivileged(Native Method)
at com.sapportals.portal.prt.dispatcher.Dispatcher.service(Dispatcher.java:430)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.runServlet(HttpHandlerImpl.java:401)
at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.handleRequest(HttpHandlerImpl.java:266)
at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:386)
at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:364)
at com.sap.engine.services.httpserver.server.RequestAnalizer.invokeWebContainer(RequestAnalizer.java:1064)
at com.sap.engine.services.httpserver.server.RequestAnalizer.handle(RequestAnalizer.java:265)
at com.sap.engine.services.httpserver.server.Client.handle(Client.java:95)
at com.sap.engine.services.httpserver.server.Processor.request(Processor.java:175)
at com.sap.engine.core.service630.context.cluster.session.ApplicationSessionMessageListener.process(ApplicationSessionMessageListener.java:33)
at com.sap.engine.core.cluster.impl6.session.MessageRunner.run(MessageRunner.java:41)
at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37)
at java.security.AccessController.doPrivileged(Native Method)
at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:104)
at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:176)Hi Vijay,
Thanks for the quick reply.
I have gone through the notes 1535201 & now on 1606563 after your advise.
Both the notes says the fix is available on 7.01 after SP 07 and we are on SP 14 already.
Also just in case I did checked with our basis and they confirmed we are a head and we have the above notes in our release already.
Unfortunately the notes are not the solution to the investigation till date.
Thanks,
Sai -
How to install 2-port vic3 2fxs/DID and 2-port vic2 fxo on cisco 2801 router
Hello
I'm looking for information on how to install 2 newly purchased cards and keep running into dead links. The cards I bought are for a CISCO-2801-CCME/K9 with PVDM2-8, FL-CCME-25, SP Services 128F/256D cisco router:
vic3 2fxs/DID and a vic2 2fxo.
I keep finding documents on how to install these cards but all links are dead and leading to nowhere.
http://www.cisco.com/en/US/docs/routers/access/interfaces/ic/hardware/installation/guide/2port_FXS_DID_VIC.html#wp1065062
The 2 documents i'm looking for are: how to install a 2-port vic2 fxo cards on cisco 2801 router and how to install 2-port vic3 2fxs/DID cards on the same 2801 cisco router.
NOTE: I've never installed these cards and am not sure if:
Does my ios support both of these cards?
and which slots do I install those in the router.
I have 4 slots like this:
slot 0: This slot only accepts VIC's ***This could be used for the vic3 2fxs/DID card correct?
slot 1: Nothing written here ****What can i install in this slot?
slot 2: This slot only accepts VIC's and WIC's ***If I buy a WIC and install here which other slot can i install my VIC2-2FXO card in ?
slot 3: Nothing written here ***What can i install in this slot?
Any chance someone can help me out with this.
Thanks very muchOk
I was able to figure out what goes where and found out that the IOS i had c-2801-spservicesk9-mz.124-15.T10.bin with cme-full-4.1.0.2 tar didn't support the vic3 2fxs/DID card. I then found the one that works which is the c2801-spservicesk9-mz.124-22.YB5.bin.I am now able to see my new hardware interfaces. The question I have now is since the previous version ran with cme-full-4.1.0.2 tar i'm not sure if this needs to be changed since in the compatibility matrix i found this IOS c2801-spservicesk9-mz.124-22.YB5.bin to be compatible with cme-full-7.1.0.0 tar
Do i need to remove cme-full-4.1.0.2 tar and install the cme-full-7.1.0.0 tar?
If yes, i know how to install the cme-full-7.1.0.0 tar but how do i remove the other cme-full-4.1.0.2 tar file in order to be able to install the other version?
Thanks -
Proper amount of DSP resources in router?
Let's say we have a small site with 25 IP phones, 4 analog devices using a FXS module in the router and an ISDN PRI circuit using a T1 module in the router. I assume a PVDM3 module with 64 DSPs would be more than enough to handle that site? Does the FXS module have its own DSP resources and we don't need to figure those in? I figure the ISDN PRI would use up to 23 DSP resources and then what's left out of the 64 on that PVDM3 could be used for conferencing, media termination point and so on. Am I thinking about this correctly? Sound reasonable (64 DSPs for a site like that)?
I didn't know there was one....but I just found it. Thanks
-
Hi,
We are getting the following error when certain data driven subscriptions are fired off: "the query processor could not start the necessary thread resources for parallel query execution". I've read other posts that have the same error, and
the solution usually involves adjusting MaxDOP to limit the number of queries that are fired off in parallel.
Unfortunately, we cannot change this setting on our server for performance reasons (outside of data driven subscriptions, it negatively impacts our ETL processing times). We tried putting query hints like "OPTION (MAXDOP 2);" in the reports
that are causing the error, but it did not resolve the problem.
Are there any settings within Reporting Services that can be adjusted to limit the number of subscriptions that get fired off in parallel?
Any help is appreciated - thanks!Yes, that is correct. It's a painful problem, because you don't know which specific subscription failed. For example, we have a data driven subscription that sends out about 800 emails. Lately, we've been having a handful of them fail. You don't know
which ones out of the 800 failed though, even from the RS log files - all it tells you is that "the
query processor could not start the necessary thread resources for parallel query execution".
Thanks, I'll try changing <MaxQueueThreads> and will let you know if it works.
On a side note: I've noticed that it is only reports with cascading parameters (ex. where parameter 2 is dependent on the selection from parameter 1) that get this error message... -
Dears,
I need the DSP Module For LabVIEW 2011, is it Available? and where can I Download it ?
Thanks
Ahmed AbdulbakyHi Ahmed,
I posted this in error. I did not see that Ryan had already answered this.
Ryan is correct. The latest version is 8.6
You can download the latest version of the DSP module from ni.com/downloads. The exact URL is shown below:
http://search.ni.com/nisearch/app/main/p/bot/no/ap/tech/lang/en/pg/1/sn/ssnavdl/q/dsp/#
I hope this information helps.
Regards,
James D.
Applications Engineer
National Instruments -
VIC3-2FXS/DID VS VIC3-2FXS-E/DID
hi all,
we'll upgrade our router from 2811 to 2911.
the current 2811 uses VIC2-2FXS but saw on cisco's website that we need a VIC3 instead.
i saw there's two versions of this card, the other has an 'E'.
what's the difference between the two? can i just get a VIC3-2FXS/DID?Hi John,
The difference is explained in the following link
http://www.cisco.com/c/en/us/products/collateral/interfaces-modules/ip-communications-voice-fax-network-modules/product_data_sheet0900aecd801c595e.html
VIC3-2FXS-E/DID is designated as an "Off-Premise Extension Lite" product offering. This means that while the module addresses a subset of the off-premise extension applications, it should be noted that the module is not in full compliance for off-premise usage.
HTH
Manish -
I have a NM-HDV module with two PVDM-16 modules and a VWIC-1MFT installed in a 2811. I have a VIC2-2FXO card that I need to install into one of the HWIC slots. Is there any way that I can share the DSP resources from the NM-HDV for the new FXO card or do I have to install new PVDM2 dsp modules in the 2811?
Can we put PVDM2-64 on NM-HDV network module ?
Because we are using NM-HDV module with PVDM12, we want to add PVDM2-64 on this module. will it possible?
Regards, -
REP-0059: Unable to locate resources for subcomponent 'DE'.
Hi,
I am working on Report Builder: Release 3.0.5.8.0.
When I run the command r30run I am getting the following error -
Report Builder: Release 3.0.5.8.0 - Production on Wed Apr 20 15:54:38 2005
Copyright (c) Oracle Corporation 1979, 1996. All rights reserved.
REP-0059: Unable to locate resources for subcomponent 'DE'.
Check the location of resource file.
Previously I did not have the $ORACLE_HOME/reports30/mesg folder and hence I was getting the error -
REP-0001: Unable to find the Report Builder message file. Please verify your installation.
My id does not have access to the files in mesg folder.
Could this be a reasn for the REP-0059 error.
Please advise.
Thanks in advance,
Sumithello,
it looks as if there was somenting wrong with your installation. i am a bit concerned that you are using a product that old. there is no support available for this product as it has been de-supported for several years now.
i would strongly suggest you move to a more recent release.
thanks,
ph. -
4FXS-DID configuration problem using BRI to receive/send calls from/to PSTN
Hi to all.
Follow is the partial configuration of my CME.
It has a 4FXS card to use analog phones and faxes, and 4 ISDN Basic Rate interfaces.
On each port of the 4FXS DID card happens the following:
If I enable direct-inward-dial
I can receive calls from PSTN.
Off hooking the analog phone I cannot hear any free line tone. I cannot make any call from that phone.
If I disable direct-inward-dial
I cannot receive directly calls form PSTN.
Callers on PSTN after typing my number, they hear a free tone. Then just typing the extension desired the phone ring.
Off hooking the analog phone I hear a free line tone. I can make normal calls to everyone.
I have half the configuration working.
Where am I wrong?
I really appreciate your help.
Thanks to all.
Giorgio.
CME#sh ver
Cisco IOS Software, 2800 Software (C2800NM-IPVOICEK9-M), Version 12.4(24)T3, RELEASE SOFTWARE (fc2)
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
CME uptime is 2 days, 15 hours, 49 minutes
System returned to ROM by power-on
System restarted at 18:54:45 CDT Fri Aug 2 2013
System image file is "flash:/c2800nm-ipvoicek9-mz.124-24.T3.bin"
Cisco 2811 (revision 53.50) with 249856K/12288K bytes of memory.
Processor board ID FTX1120A08L
2 FastEthernet interfaces
4 ISDN Basic Rate interfaces
16 terminal lines
4 Voice FXS interfaces
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
1948656K bytes of USB Flash usbflash0 (Read/Write)
497448K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
CME#sh telephony-service
CONFIG (Version=7.1)
=====================
Version 7.1
Cisco Unified Communications Manager Express
isdn switch-type basic-net3
voice translation-rule 1
rule 1 /^2929091\(..\)/ /\1/
rule 2 /^2929091\(.\)/ /\1/
rule 3 /^02929091\(..\)/ /\1/
rule 4 /^02929091\(.\)/ /\1/
voice translation-rule 2
rule 2 /\(.*\)/ /02929091\1/
voice translation-rule 10
rule 1 /\(^......$\)/ /0\1/ type national national plan isdn isdn
rule 8 /\(^......$\)/ /00\1/ type international international plan isdn isdn
voice translation-profile PSTN-IN
translate calling 10
translate called 1
voice translation-profile PSTN-OUT
translate calling 2
interface BRI0/0/0
description Isdn channels 1 & 2
no ip address
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/0/1
description Isdn channels 3 & 4
no ip address
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/1/0
description Isdn channels 5 & 6
no ip address
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/1/1
description not used
no ip address
shutdown
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
voice-port 0/0/0
translation-profile incoming PSTN-IN
translation-profile outgoing PSTN-OUT
compand-type a-law
description Connessione con CO Telecom channels 1 & 2
voice-port 0/0/1
translation-profile incoming PSTN-IN
translation-profile outgoing PSTN-OUT
compand-type a-law
description Connessione con CO Telecom channels 3 & 4
voice-port 0/1/0
translation-profile incoming PSTN-IN
translation-profile outgoing PSTN-OUT
compand-type a-law
description Connessione con CO Telecom channels 5 & 6
voice-port 0/1/1
description Disponibile
voice-port 0/2/0
input gain 14
connection plar 83
description Interphone 40
station-id name Citofono
station-id number 40
caller-id enable
voice-port 0/2/1
cptone IT
description Ced 35
station-id name CED
station-id number 35
caller-id enable
voice-port 0/2/2
cptone IT
description FAX_1 50
station-id name FAX_1
station-id number 50
caller-id enable
voice-port 0/2/3
cptone IT
description FAX_2 60
station-id name FAX_1
station-id number 60
caller-id enable
dial-peer voice 1001 pots
description **Sends call to PSTN line 1-2**
destination-pattern 0T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/0
dial-peer voice 2001 pots
description **Receives calls coming from PSTN line 1-2**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/0
dial-peer voice 1003 pots
description **Sends call to PSTN line 3-4**
destination-pattern 0T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
dial-peer voice 2003 pots
description **Receives calls coming from PSTN line 3-4**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/1
dial-peer voice 1005 pots
description **Sends call to PSTN line 5-6**
destination-pattern 0T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 2005 pots
description **Receives calls coming from PSTN line 5-6**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/1/0
dial-peer voice 2035 pots
description **Receives calls coming from PSTN to Extension 35**
answer-address 35
destination-pattern 35$
incoming called-number 35
port 0/2/1
dial-peer voice 2040 pots
description **Receives calls coming from PSTN to Extension 40**
destination-pattern 40
incoming called-number 40
no digit-strip
direct-inward-dial
port 0/2/0
dial-peer voice 2050 pots
description **Receives calls coming from PSTN to Fax 50**
destination-pattern 50
incoming called-number 50
no digit-strip
direct-inward-dial
port 0/2/2
dial-peer voice 2060 pots
description **Receives calls coming from PSTN to Fax 60**
destination-pattern 60
incoming called-number 60
no digit-strip
direct-inward-dial
port 0/2/3
CME#Hi Paolo.
Sorry for the delay. I was on holiday.
I would like to keep separate incoming calls from outgoing calls.
So I decided to keep two dial peers for every BRI interface.
I followed your suggestion on eliminate commands:
"incoming called-number" on FXSs,
various "progress_ind" on BRIs
Also I eliminated "direct-inward-dial" on FXSs,
Today I reconfigured and right tested the dial peers as following:
! Bri Interfaces
dial-peer voice 1001 pots
description **Sends call to PSTN line 1-2**
destination-pattern 0T
port 0/0/0
dial-peer voice 2001 pots
description **Receives calls coming from PSTN line 1-2**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/0
dial-peer voice 1003 pots
description **Sends call to PSTN line 3-4**
destination-pattern 0T
port 0/0/1
dial-peer voice 2003 pots
description **Receives calls coming from PSTN line 3-4**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/1
dial-peer voice 1005 pots
description **Sends call to PSTN line 5-6**
destination-pattern 0T
port 0/1/0
dial-peer voice 2005 pots
description **Receives calls coming from PSTN line 5-6**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/1/0
! FXS interfaces
dial-peer voice 2035 pots
description **Receives calls coming from PSTN to Extension 35**
destination-pattern 35
no digit-strip
port 0/2/1
dial-peer voice 2040 pots
description **Receives calls coming from PSTN to Extension 40**
destination-pattern 40
no digit-strip
port 0/2/0
dial-peer voice 2050 pots
description **Receives calls coming from PSTN to Fax 50**
destination-pattern 50
no digit-strip
port 0/2/2
dial-peer voice 2060 pots
description **Receives calls coming from PSTN to Fax 60**
destination-pattern 60
no digit-strip
port 0/2/3
Thanks a lot Paolo. :-)
Giorgio. -
Resources for first java soap client/server endeavour?
Hello community,
Im looking for some good resources for setting up a soap server, on apache tomcat, to handle incoming soap messages and send a soap response to the client.
Any links to examples/sample code are greatly appreciated. I am completely new to webservices.
your help is appreciated, thank you.Christ, how did I mange to make those typos?
You need a webserver to accept the requests, and something like Tomcat to run your web service. Since Tomcat has a webserver (doesn't it include Apache?) already, Tomcat is all you need, but it won't really care whether you send some XML using HTTP or HTML form data using HTTP. It's still HTTP. -
Java Programming Resources for starting out
Hey guys,
What are the best resources for starting out with Java. I did a bit of work with Java in my Uni course but it was about 2 years ago. I'd like to go over it from the start and get familar with everything again.
Can anyone suggest some good places to get Resources, Tutorials and Exercises for Java Programming?
Thanks in advance.Getting Started With Java
[Sun's basic Java tutorial|http://java.sun.com/docs/books/tutorial/]
[Sun's New To Java Center|http://java.sun.com/learning/new2java/index.html]
Includes an overview of what Java is, instructions for setting up Java, an intro to programming (that includes links to the above tutorial or to parts of it), quizzes, a list of resources, and info on certification and courses.
jGuru
A general Java resource site. Includes FAQs, forums, courses, more.
[Yawmarks List|http://forums.devshed.com/java-help-9/resources-for-learning-java-249225.html]
[The Java Developers Almanac|http://www.amazon.com/exec/obidos/tg/detail/-/0201752808?v=glance]
[http://javaalmanac.com|http://javaalmanac.com]
Bruce Eckel's [Thinking in Java(Available online.)|http://mindview.net/Books/DownloadSites]
Joshua Bloch's [Effective Java|http://www.amazon.co.uk/exec/obidos/Author=Bloch,%20Josh]
Bert Bates and Kathy Sierra's [Head First Java|http://www.amazon.com/exec/obidos/tg/detail/-/0596004656?v=glance ]
James Gosling's [The Java Programming Language|http://www.bookpool.com/sm/0321349806]
Gosling is the creator of Java. It doesn't get much more authoritative than this.
Joshua Bloch and Neal Gafter [Java Puzzlers.|http://www.javapuzzlers.com/]
Maybe you are looking for
-
Issuing two outputs at a time.
For a given invoice,we have to issue ouput(Smartform) to Bill-to-party with BP Address. Also we need to check the buying group(KNB1-EKVBD) of sold-to-party with that of Bill-to-party. If the buying group of SP and BP is different,then we need to issu
-
Itunes 10.6.1 And Apple Mobile Support
I've been at this for 5 hours, and I'm taking my pride away and going to the forums for some help I just received an iPod Touch 3.x.x from my friend, and when I hook it up to my desktop, the classic error "The iPod you connected cannot be used becaus
-
Transfer Lion (I bought on App Store) to a newer Mac Mini (July 2011)?
I just purchased a new "July 2011 Mac Mini" on ebay. Can I transfer the Lion (I bought on App Store) off of my older Mac Mini to the new Mini? I purchased Lion the day it came out from the App Store and had it downloaded on my 2 GHz Intel Core 2 Duo
-
few of my songs on ipod wont play fully they play for few seconds and then next song is selected to play. why is that?
-
No Network setting under General tab
I am trying to set up tethering. I am on iPhone 3gs, OS6. I have been advised to go to the General tab in settings then go to Network, there is no Network available. I have Personal Hotspot set up under Settings, which has bluetooth and USB, but want