DTMF Tones not working with 7.7.64.103

Hi, I'm trying to dial into a conference call and the keypad tones aren't being sent through from Windows. I'm running Windows 7. Any suggestions of how to get round this will be gratefully received as it'll cost a fortune to use landlines or mobile phone to dial into the meetings. Thanks, Rachel.

I belive that Skype have broken something at the backend. See:http://community.skype.com/t5/Windows-desktop-client/Skype-not-generating-DTMF-tones-again/td-p/4073503

Similar Messages

Touch tones not working with FaceTime/Handoff Calls in Yosemite

Has anyone successfully used the new Handoffs feature to call into a conference bridge? I've tried and failed a few times now. I hear the touchtone sounds when I enter the numbers on my keyboard but they are not recognized. One service - GotoMeeting - responds back with "You entered zero numbers".
Here is a number you can try calling. +1 (646) 749-3131
If it is responding back to you with "You entered [the numbers you entered]" then I guess it is just happening to me.
Thanks for your help!
---Marc

Works fine on my MacBook Pro (Retina, 15-inch, Late 2013), and iPhone 6 with iOS 8.1.

DTMF not working with UCCX

Hi
We have noticed that DTMF is not working with UCCX,
Call flow ->
PSTN (SIP)-> CUBE - (SIP)-> CUCM - > UCCX
UCCX DTMF is working with IP Phones which are registered with CUCM, But not working with PSTN incoming calls, also we have Unity Connection, for this DTMF is working with PSTN incoming calls,
Please help to troubleshoot this issue,
Rgds
$

What this boils down to is that the CTI Ports do not support RFC2833, only out of band over the CTI QBE protocol. This means that CUCM must "see" the DTMF packets. If CUBE offers KPML in the call SDP, CUCM will automatically request this and translate from the SIP packet into a CTI event. If CUBE is only offering RFC2833, CUCM would need to invoke an MTP on the call to intercept the RTP packets containing the DTMF event.
If this isn't working the most likely reason is that there is no MTP for CUCM to invoke, or the MTP doesn't support RFC2833 DTMF interop. The best way out of this problem is to adjust the CUCM-facing VOIP dial-peer to include both capabilities: 'dtmf-relay rtp-nte sip-kpml' CUBE, assuming it's doing media flow-through, will do the heavy lifting for CUCM. If you set the DTMF Method on the CUCM-side SIP trunk, CUCM will essentially invoke an MTP for *every* call, in most cases needlessly; that's a great way to introduce problems and break things such as faxing.
Please remember to rate helpful responses and identify helpful or correct answers.

HT201401 Q) Can anyone please help me with this: My in coming call ringing tone not working?

Q) Can anyone please help me with this: My in coming call-messges ringing tone not working? All I am getting in Vabration + Flashing light when receiveing messages or incoming Calls. I am missing my phone Calls constantly. Please Help me?
I have just received this phone as a replacement from my insurance company, as I had lost my own phone. It has taken them 3 weeks to sort this out. This has ruined my business because it has taken so long. I really do not have time to send it back to them. Because it will waist another three weeks for them to sort it out again. Please Help!

HA! By Jove I've Got it! it was simples..
TURN ON THE RINGING ON / OFF BUTTON ON THE SIDE OF YOUR PHONE JUST ABOVE THE VOLUME BUTTONS. THEN MAKE SURE THE VOLUME IS UP TO THE HIGHEST. NOW JUST TRY THIS!
I ALSO LOOKED UP A MANUAL ON IPHONE4:
Ringtones, Ring/Silent switch, and vibrate
iPhone comes with ringtones that sound for incoming calls, Clock alarms, and the Clock timer.
You can also purchase ringtones from songs in iTunes. See Chapter 22, iTunes Store, on page 94.
Set the default ringtone: Go to Settings > Sounds > Ringtone.
Turn the ringer on or off: Flip the switch on the side of iPhone.
Important: Clock alarms still sound even if you set the Ring/Silent switch to silent.
Turn vibrate on or off: Go to Settings > Sounds.
Assign a different ringtone for a contact: In Contacts, choose a contact, tap edit, then tap
Ringtone and choose a ringtone.
For more information, see Sounds on page 139.
THE REASON MY PHONE HAD NO RING TONE, WAS SIMPLY BECAUSE THE VOLUME WAS TURNED DOWN. :-/
I HOPE THIS HELPS OTHERS INFUTURE! :-D

HP Color LaserJet Pro MFP M177fw Not working with Fedora 14

Our ERP is compactible up to Fedora 14. But I newly purchased Printer(
HP Color LaserJet Pro MFP M177fw) is not working with this OS.
Give me a urgent solution

Hi @HealthITLadyRed,
I read your post and see that the printer is making noise and is stuck initializing. I would really like to be able to help you resolve this issue.
I have provided some steps to try to see if we can resolve this issue.
Check and remove any packaging material inside the printer and toner.
Disconnect the USB/Network/FAX and power the printer on Standalone.
Do a hard reset to see if that will resolve the issue.
Leave the printer on and unplug the power cable from the printer and wall outlet for 60 seconds.
Then reconnect the power cable to the printer and wall outlet rather than a surge protector.
This ensures the printer is receiving full power and may help this situation.
If the issue persists, perform a power drain by disconnecting the power cord from the back of the printer and keeping the power button pressed for 30 seconds and in case of a power switch keep the switch in ON position for 30 seconds before reconnecting the power chord.
Update the printer's firmware by a USB connection. Software and Drivers.
Select Option 2 and wait for the page to load and then select the link for firmware. This resolved the previous posters issue.
I can send a private message with another step to try.
In the forum beside your handle name just click on the envelope to view it.
How is the printer connected? (USB/Ethernet/Wireless)
What happened prior to this issue? (paper jam, changed toner) Any feedback would be appreciated.
Is this a new printer?
If you appreciate my efforts, please click the Thumbs up button below.
If there is anything else I can help you with, just let me know. Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Smart Talk not working with Bluetooth since update

I have been using Smart Talk for many months now on my iPhone. I have a bluetooth headset which I generally use.
This has worked fine (with the exception that when I get an incomming call it disconnects the bluetooth from the Smart Talk call).
But now, since installing version 1.28.0, Smart Talk is not working with my bluetooth headset at all. When I first make a call the headset is connected - I hear ringback tone. But as soon as the call is answered, the headset disconnects and the call is transferred to the iPhone itself. And the Smart Talk app does not give me any options to select the "audio source" (as it does if I make an ordinary mobile call).
As I almost exclusively use the headset, this latest update has made Smart Talk unusable for me.
Is there anyway I can get back to the previous version?

I worked out the problem... I'm using iPhone 4S iOS7
- Start BT Smart Talk from in car
- call someone, connects to bluetooth
- call someone else, connects to bluetooth
- call someone else, no bluetooth connection
- kill and restart BT Smart talk
- call someone, connects to bluetooth
- call someone else, connects to bluetooth
- call someone else, no bluetooth connection
3rd call, always no bluetooth.
It seems there is no way to select the output like with all other bluetooth devices too

Party Entrance Tone not working on CUCM 10.5(1.10000.7)

Party Entrance Tone not working on CUCM 10.5(1.10000.7) . This is an intermitent issue for Meet Me conference.
++On the CUCM Service Parameter Party Entrance Tone has is TRUE .
++On Directory number Party Entrance Tone is ON . However the Party entrance tone (Beep tone) not coming when Meet Me conference going on .
Gateway 3945 with IOS Version 15.3(3)M5, RELEASE SOFTWARE (fc3).
The conference Configureation as below.
sccp local GigabitEthernet0/0
sccp ccm 172.20.0.152 identifier 1 priority 1 version 7.0
sccp ccm 172.20.0.153 identifier 2 priority 2 version 7.0
sccp ccm 172.22.0.110 identifier 3 priority 3 version 7.0
sccp ccm 172.22.0.111 identifier 4 priority 4 version 7.0
sccp
sccp ccm group 1
bind interface GigabitEthernet0/0
associate ccm 1 priority 1
associate ccm 2 priority 2
associate ccm 3 priority 3
associate ccm 4 priority 4
associate profile 2 register ASB-DR-GW04CFB
associate profile 1 register ASB-DR-GW04XCO
dspfarm profile 1 transcode
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729br8
codec g729r8
maximum sessions 60
associate application SCCP
dspfarm profile 2 conference
codec g729br8
codec g729r8
codec g729abr8
codec g729ar8
codec g711alaw
codec g711ulaw
maximum conference-participants 32
maximum sessions 12
associate application SCCP
Can any one tell me how the party entrance tone happening when a confernce session open.Is it generated from the hardware Confernce resource which configured on the gateway while mixing the RTP streams ? Is there anything to do with CUCM or any service in CUCM to generate the Party entrance tone ?

Hi,
It looks like the following bug
https://tools.cisco.com/bugsearch/bug/CSCup27560/?referring_site=bugquickviewredir
MeetMe Party Entrance Tones stop working
CSCup27560
Description
Symptom:
- MeetMe party entrance tones stop getting played to participants when they join/leave
- The issue will go away for a few weeks if the CCM service is restarted, but then will come back.
- When the issue comes back, it fails 100% of the time.
Conditions:
This problem would occur when we have user having a call from user in different node initiate transfer and also initiate MeetMe and dial user in different node. When transfer completes, we will have a leak in current node MeetMe. This issue should have been there in all CCM versions.
Workaround:
Restarting the CCM service will correct the problem temporarily.
You can either try the workaround or upgrade to one of the fixed versions.
HTH
Manish

Standby PRI not working with voice Gateway Router & CUCM

Hi ALL ,
GOOD Day all of you .
I am facing a big problem i.e standby PRI not working with VG & CUCM , I have checked all the configuration parameter on VG & CUCM found ok but I am unable to make any call from standby link also incoming not come on the standby link . When I make a call on my Pilot no but getting busy tone .
I observer the some errors on VG like Cause i = 0x8286 - Channel unacceptable on my second PRI channel .
Please help me to reslove this proem .
Following are the PRI configuration Parameter on CUCM .
Product Specific Configuration Layout
Line Coding : HDB3
Framing : NON CRC4
Clock : External
Input Gain (-6..14 db) 0
Output Attenuation (-6..14 db) 0
Echo Cancellation Enable
Echo Cancellation Coverage (ms) 64
PRI configuration on VG
interface Serial0/0/1:15
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
isdn bind-l3 ccm-manager
BR,
SANDIPAN

Hi Craig ,
Thanks for your reply .
We are using the full 30 channel E1 PRI .
following are PRI Channel Statistics:
%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 1. Layer 3 output may not apply
ISDN Se0/0/0:15, Channel [1-31]
Configured Isdn Interface (dsl) 1
   Channel State (0=Idle 1=Proposed 2=Busy 3=Reserved 4=Restart 5=Maint_Pend)
    Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    State   : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
   Service State (0=Inservice 1=Maint 2=Outofservice 8=MaintPend 9=OOSPend)
    Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    State   : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Please find following debug error
VG_RO_01#isdn test call interface serial 0/0/0:15 09665484798
Mar 7 03:00:54.570: ISDN Se0/0/0:15 Q921: User RX <- RRp sapi=0 tei=0 nr=5
Mar 7 03:00:54.570: ISDN Se0/0/0:15 Q921: User TX -> RRp sapi=0 tei=0 nr=4
Mar 7 03:00:54.570: ISDN Se0/0/0:15 Q921: User TX -> RRf sapi=0 tei=0 nr=4
Mar 7 03:00:54.574: ISDN Se0/0/0:15 Q921: User RX <- RRf sapi=0 tei=0 nr=5
CCIL_PUNE_DR_VG_RO_01#
Mar 7 03:00:55.994: ISDN Se0/0/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Called num 09665484798
Mar 7 03:00:55.994: ISDN Se0/0/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=5 nr=4
Mar 7 03:00:55.994: ISDN Se0/0/0:15 Q931: SETUP pd = 8 callref = 0x0084
Bearer Capability i = 0x8890
Standard = CCITT
Transfer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9839F
Exclusive, Channel 31
Called Party Number i = 0x81, '09665484798'
Plan:ISDN, Type:Unknown
Mar 7 03:00:56.006: ISDN Se0/0/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=6
Mar 7 03:00:56.018: ISDN Se0/0/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=4 nr=6
Mar 7 03:00:56.018: ISDN Se0/0/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x8084
Cause i = 0x8286 - Channel unacceptable
Mar 7 03:00:56.022: ISDN Se0/0/0:15 Q921: User TX -> RR sapi=0 tei=0 nr=5
Mar 7 03:00:59.995: ISDN Se0/0/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=6 nr=5
Mar 7 03:00:59.995: ISDN Se0/0/0:15 Q931: SETUP pd = 8 callref = 0x0084
Bearer Capability i = 0x8890
Standard = CCITT
Transfer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9839F
Exclusive, Channel 31
Called Party Number i = 0x81, '09665484798'
Plan:ISDN, Type:Unknown
Mar 7 03:01:00.007: ISDN Se0/0/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=7
Mar 7 03:01:00.019: ISDN Se0/0/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=5 nr=7
Mar 7 03:01:00.019: ISDN Se0/0/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x8084
Cause i = 0x8286 - Channel unacceptable
Mar 7 03:01:00.019: ISDN Se0/0/0:15 Q921: User TX -> RR sapi=0 tei=0 nr=6
Mar 7 03:01:03.995: ISDN Se0/0/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=7 nr=6
Mar 7 03:01:03.995: ISDN Se0/0/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x0084
Cause i = 0x80E6 - Recovery on timer expiry
Mar 7 03:01:03.995: ISDN Se0/0/0:15 **ERROR**: CCPCC_CallOrigination: SETUP timed-out (2nd T303) to NETWORK. The SETUP failed.
BR ,
SANDIPAN

I have recently upgraded my iMac Intel G5 iSight to OS 10.6.8 and now the internal mic does not work with skype or facebook. I can here static when playing back clips. Do I need to update firmware or reload old sys parts

I have recently upgraded my iMac Intel G5 iSight (iMac5,1) to OS 10.6.8 and now the internal mic does not work with skype or facebook. I can here static when playing back clips. Do I need to update firmware or reload old system parts. I have zapped PRAM. The blue indicator in system audio panel will appear for a second as I slide the bar for internal mic but then it disappears. Is there a fix?

The sound seems very faint but can here static on playback.

My operating system windows XP not working with photoshop cloud, why not?

I need to add 2 more licences for photoshop cloud and I'm being told my operating system windows XP does not work with Photoshop cloud. We already have 2 pcs using it in our office so why not?
Please help
Roy

Do you have the latest version of iTunes? If not, get it at:
http://www.apple.com/itunes

Adobe creative cloud eea 1.5 is not working with our asus Eee box , celeron j1900 2.00 ghz, 4gb of ram, 64bit. can settings be changed in adobe?

adobe creative cloud eea 1.5 is not working with our asus Eee box , celeron j1900 2.00 ghz, 4gb of ram, 64bit. can settings be changed in adobe?

A chat session where an agent may remotely look inside your computer may help
Creative Cloud chat support (all Creative Cloud customer service issues)
http://helpx.adobe.com/x-productkb/global/service-ccm.html

Application is not working with mouse

Dear All,
We have a strange issue in the our application (Oracle form) in the one of our client machine.
Some times the forms are not able to work with the mouse but is able to work with the keyboard. After one or two machine restart its again working. When the issue occur we can able to work in other applications using mouse.
Our Applications server is in Other country and client are accessing from India.
This occurs for some user and not for all.
Application server Version 10.1.2.0.2.
Oracle Database 11g Enterprise Edition Release 11.2.0.1.0 - 64bit
Java Plug-in version 1.6.0_31 .
Please any info will help us lot.

Thank you for the quick replies Michael Ferrante and HamidHelal.
But since its occurring for some users (perticulary indian users) and some times. And also its occurring in production environment not in development environment.
Even the java control panel is not working with mouse.
For other country customers everything working fine.
So its difficult for me to apply the patch with these uncertainties.
Checking with fresh java installation and let you know the status.
Thanks.

Voice Memo is not working with iOS 8.2

Voice Memo Records is not working with iOS 8.2. how to fix it?

Voice Memo Records is not working with iOS 8.2. how to fix it?

Iphone 4 Alerts Tones Not Working / Ringer Is WORKING KINDLY REPLY ME

HI , PLEASE HELP ME I WANT TO FIX THIS ISSUE THAT I AM GETTING PLEASE HELP
MY ISSUE IS IPHONE 4 ALERTS TONES NOT WORKING AND CALL RINGER IS WORKING.. PLEASE HELP ME!

If the iPhone came from the US then it is locked to AT&T. To unlock an iPhone the original carrier is the only one who can unlock the iPhone and AT&T will not unlock iPhones. So there is not official way to unlock the iPhone 4.
At this point there is no way to hack the iPhone 4 running 4.2.1 to unlock it either so the phone and messaging apps will never work. You basically have an iPod touch.

On updating my iphone it shows no network inspite the sim inserted,now it also not working with itunes.i cant see menu page on display screen

on updating my iphone it shows no network inspite the sim inserted,now it also not working with itunes.
i cant see menu page on display screen

http://support.apple.com/kb/HT1808

DTMF Tones not working with 7.7.64.103

Similar Messages

Maybe you are looking for