Dual 9800GTX+'s not working

Ok I am running XP x64 SP2 with the Speedster w/o a on-board video, Updated BIOS to the BIOS the allows dual Quad Cores. I have 2 NVIDIA 9800 GTX+'s and I have them installed in both PCI-E slots. Now I am unable to get the other card to even be seen by windows. I have tried a number of things including beta drivers for SLI multi monitor, Updating drivers a number of times. disabling SLI. and still no additional GC
Any ideas?
Here is a better list of things I have tried: http://forums.nvidia.com/index.php?showtopic=84281&st=0&p=477646&#entry477646

Quote from: jus71n742 on 30-December-08, 05:16:58
Well it may not be OS cause that same PSU supplied to Win Pro 32bit and never had an issue. I Ran Memtest w/o and OS and nothing errored. So I am thinking I prob need to ditch 3 of those rails. SHould have read more into the PSU when I was doing the research for my build. I will run Orthos next
Orthos would run for about 10-15 min and then Shutdown...never crashed but would just power down. So that mean that it is most likely a PSU problem?
Another Question...Why would Windows crash and/or shutdown while Linux would only power down?
"Orthos would run for about 10-15 min and then Shutdown...never crashed but would just power down. So that mean that it is most likely a PSU problem?"
One of the CPU's is overheating or weak/defective PSU.
I've told you to watch out CPU underload temp during Orthos testing too.

Similar Messages

Lumia 630 dual sim headphones not working

After denim update on lumia 630 dual sim headphones not working properly in india

Hi, kingpawan. Is the issue the same when you're using another compatible headset? Are you experiencing this when you're watching a video? Did you happen to check if the phone's system settings are all updated? To do this, go to Settings > swipe to applications > store > check for updates. We'd love to hear your response. BTW, welcome to our community!

Z97 Gaming 5, Dual Channel RAM not working?

Here are my specs for the moment , Windows 7, Intel Core i7 4770k, 8,00GB Single-Channel DDR3 @ 666MHz (9-9-9-24), Nvidia GeForce GTX 780 (EVGA)
As the title says dual RAM is not working, when I put all 4 RAM sticks in their slots or even just two in dual channel mode my monitor will not respond and the screen is just black, can't even go to BIOs.
The BIOs settings are at 1333 MHz and 1.5 v, I've tried raising the volt and lowering it, anyone have any ideas?
I've tried the 1-3 and 2-4 slots with two 4gb sticks and it does not work, but the 1-2 and 2-4 works fine, have also tried all the individual sticks so none of them are faulty.
RAM: Corsair XMS3 DDR3 1333MHz 16GB KIT CL9 4x4

Quote
I've tried the 1-3 and 2-4 slots with two 4gb sticks and it does not work, but the 1-2 and 2-4 works fine, have also tried all the individual sticks so none of them are faulty.
Please clarify. You mean a single stick works in 2 or 4 but not 2 and 4 together? So that means DIMM slot #3 is the only one that doesn't work at all? My suspicion is a grounding or short under the mainboard by an errant standoff, or the DIMM slot has some debris in it, or the slot is just plain faulty. Other possible is a pin problem in the CPU socket.

New MacBook (Aluminum), new Time Capsule (Dual-Band), backups not working

My Mom got a new (refurbished) 13.3" MacBook (Aluminum) and new (not refurbished) Time Capsule 500 GB (Dual-Band.) The Time Capsule is working great for wireless internet and we can copy files to and from it, but Time Machine backups are not working. I enabled Time Machine, selected her TC, and then when it tries to backup it sits at the preparing stage for a little while and then gives a very unhelpful "the backup failed" message. Unfortunately I don't have the exact error message, but it never gets out of the preparing phase. It doesn't stay in preparing forever, it only stays there for a minute or so before it gives up and reports the backup failed message and stops. It's unclear to me, searching these forums, if this problem is the same as others are reporting.
I've tried turning off Time Machine and back on, removing and reselecting the Time Capsule, etc. Nothing makes a difference. There are no backup files on the TC - it's brand new.
This happened out of the box, but I also tried installing the latest Time Capsule firmware. It didn't help.

Apple needs to create a configuration tool that configures all the Apple devices one owns by creating a network diagram using drag and drop symbols...
Sounds like a cool suggestion. If you want Apple to hear it, go to www.apple.com/feedback/timecapsule.html

Dual 30" ACDs not working correctly in mirror mode

My Apple Care guy is telling me that the problem I have is known and there is nothing they can do for me. I find this hard to believe, especially since it seems like I'm the only one complaining about this, so, before throwing in the towel and accepting defeat I ask, "Does anyone else have two 30 inch ACDs that do not work correctly while in mirror mode?". I have a Mac Pro4,1 eight core Intel Xeon with the ATI HD 4870. The details of my problem are in another post here (http://discussions.apple.com/thread.jspa?threadID=2659330&tstart=0).

Charlie Parker-
I do not represent the position of Apple, Inc. I am another User, like you.
After reviewing your Videos, I suggest that you may never be satisfied with the performance of two displays on one display card.
You are a very exacting and demanding user. You may want to consider having each display on its own card to maintain crispness and lack of transient artifacts.

Dual Channel Does Not Work!!!

As the title states, I can not get anything to work in dual channel mode. I have tried 3 pairs of matched memory, and they all do pretty much the same thing. These are the modules tried:
Mushkin: http://www.newegg.com/app/ViewProductDesc.asp?description=20-146-289&depa=0
Corsair: http://www.newegg.com/app/ViewProductDesc.asp?description=20-145-432&depa=0
OCZ: http://www.newegg.com/app/ViewProductDesc.asp?description=20-146-882&depa=0
After perusing this forum I found several things to try, so I tried them all, even bought a new PSU, nothing helps. Then I actually called tech support, after about an hour on the phone(on my own dime) they decided it was a bad mobo...(which was my assumption and why I called..)
Anyways, here is what happens when I try to boot with default settings, and SPD. It will either post and freeze while trying to load windows, or it will not post, and hang during the process, at which point the monitor loses signal. The only way I can get it to load windows in dual channel mode is if I set the DRAM freq down to 266 and raise the latency values far from spec, and then it is highly unstable in windows...On top of all this, the only ram that is stable in single channel mode is the OCZ, but only when 1 module is installed...in bank 1.........can someone please help me!!

Quote
Why do I have to set the DRAM voltage to 2.9v, when everyone else has theirs set to 2.75 - 2.8v ???
you shouldnt. even corsair recommends to set their stuff to 2.7v or 2.8v and i have never heard that anyone needed more voltage on his/her memory in order to make it run stable in dual channel mode.
since you've said that you have done "all the little tricks" posted in the forum i dont know what to advice further on. maybe you tell us what you have already done...

Dual sim a916 not working ?

What you need is to flash another ROM to the phone. There's one called A916 S1205 141013 which can be downloaded from needrom dot com (but you need to sign up as a member first) This gives full dual-SIM, dual standby, but only after you also key in the code * # * # 5448264 # * # * on the phone pad. This now shows both signal strengths and you can make and answer calls from either (and texts). When you make a call, you get an easy two-way button to choose which network to use. Check your phone with Malwarebytes - mine was shown to have 4 items of malware in....get this.... the Lenovo apps which of course makes them un-deletable normally. This left me no alternative but to 'root' the phone so I could delete the offending apps, and Malwarebytes confirms no more nasties on my phone. Of course, I'll never know if the original firmware had malware as I never thought to check - it was only while I was reading reviews on the UK Amazon site that I heard about this. BTW, you do know that Sim 2 is only 2G capable don't you?

I bought a new a916 and one of the main reasons was because it has a dual sim option I have installed my main sim which is O2 and my second sim is EE on orange can I get some confirmation as to why this is is it becausecit has Chinese firmware and not English and if I can change to an English firmware to make it work andcif so where can obtain the new firmware thanks.

M92p DisplayPort to dual Displayport adapter not working

I have purchased several M92p tiny computers and had great success with them. however, we are wanting to start hooking up 4 monitors as advertised using the “Displayport to Dual Displayport adapters” to connect two identical monitors to a single displayport on the PC. When we hook up this adapter neither monitor connect. The status lights on the adapter for each displayport just blinks green (I assume they should be solid green lights). Does anyone have any idea what is going on with these adapters or can locate any technical documenation for them. I have verified the displayports on the computers work by connecting monitors directly to them, I have tried several different display driver options since the device doesnt have any drivers, and different types of monitors. I have called lenovo support and they say everything is working as designed… ( yet nothing displays… at all…) Any suggestions or help is greatly appricated.

Bigg, Here is a quote from Lenovo's website regarding the tiny form factor...
"Multiple Monitor Display
Maximize productivity with independent display support for up to three independent displays or Mosaic quad display. The expanded work area and easier navigation between applications helps reduce errors and improve productivity as you extend your desktop across monitors. (Requires optional second DisplayPort connector.)"
http://shop.lenovo.com/us/en/desktops/thinkcentre/m-series-tiny/m92p/#features
in the next post you can see in the image I uploaded that I have two DP and one VGA... I would think I am missing something but I cannot figure it out...

I have a late 2008 Macbook Pro, I am trying to run MW3 but it will not work without crashing a few minuets into the game. The general specs on my computer are a dual processor 2.53 ghz. 4 gb ram and a NVIDIA geforce 9400 (9600 is the alternate card)

I have a late 2008 Macbook Pro, I am trying to run MW3 but it will not work without crashing a few minuets into the game. The general specs on my computer are a dual processor 2.53 ghz. 4 gb ram and a NVIDIA geforce 9400 (9600 is the alternate card).
Things to note:
I have been unable to update firmware on this computer for about a year now. Im not sure why.
I am running a bootleg copy of Windows XP on this computer, I would not like to spend $149 to get Windows 7 if possible.
any thoughts on the matter would be greatly appreciated, thank you.

Why don't you take your 'old' MBP into your local Apple Store and have them check out everything that's wrong with it - and I mean everything? Then, when you get an estimate about how much it would cost to get the machine completely repaired, ask about the Apple flat-rate repair pricing?
It's worth a shot - and with what you may save, you can put in the bank for a new MBP.
Clinton

What key(s) do i type to change language from english to other? i am writing s story in dual languages. i was told to click command and space bar together but it is not working.

what key(s) do it type to change language from english to other? i am writing a story in dual languages. I was told to click command and space bar together but it is not working.

Command Spacebar opens Spotlight as you have found out. If you want to change languages you need to say what app you are using to write the story in, I'm guessing you are using Pages or MS Word. If that's the case
Pages: Open Inspector - Click the T tab - Click Language and change your language.
MS Word: Tools Menu - Language - Choose your language.

Dual Monitors on Mac Mini Late 2014 not working on Dell S2340Lc

Hey guys,
Got a mac mini and using it mainly for work. Working for an ISP and no one has used macs and I've opted to be the poor sucker that gets to deal with old people that don't know how to mac very goodly.
I have two Dell S2340Lc monitors. I have one connected up via HDMI and that works perfectly fine. I turned off the mac, I plugged in Monitor 2 with a MiniDP/Thunderbolt to HDMI adapter, powered on the mac and whilst it was booting, it had the Apple logo and the loading bar on the Dell display plugged in to the thunderbolt to hdmi adapter and then once it loaded up the log in screen, it went to the HDMI display. I logged in and in the displays section, the monitor plugged in to the thunderbolt to hdmi adapter isn't being detected, however I can plug it in to a Samsung 55 Inch Smart TV and it works just fine. I can set up dual monitors between the TV and the monitor in HDMI, but the Dell S2340Lc will only work with a HDMI cable into the HDMI port on the mac mini and will not work through the thunderbolt to hdmi adapter. On the display it just says that there is no signal coming from the computer.
Just wondering if any of you apple gurus had any ideas as to why this isn't working?
Thanks!

What if you switch monitors?
What happens if yo only have the Thunderbolt>HDMI>Dell monitor connected?
Try resetting the SMC and PRAM
Intel-based Macs: Resetting the System Management Controller (SMC)
About NVRAM and PRAM
Call Apple. You get 90 days or free telephone support
Complimentary Support (USA)

Internet working in windows xp, not working in leopard (dual boot)

i have a problem with connecting to the internet in leopard, but not in windows xp. i'm on a dual boot machine (mac mini g5 1.66).
the problem started in an odd way:
everything was working fine, i left the computer open for a few hours (fell asleep) and when I came back I couldn't connect to the internet whatever browser I was using. I restarted the computer in windows and it works fine. Obviously this is not a problem related to the modem or the cables - something must have changed in Leopard. But I did not install any program recently.
I checked the Network tab in System Pref - nothing wrong, I checked disk permissions and corrected them - no change, I checked for unusual threads or processes in Activity Monitor - nothing.
I tried using the Network Utility and sent a few pings, but it's not working. However, both the Network Utility and Activity Monitor report outgoing and incoming packets of data, as if the connection were working.
Can you help me solve this problem without reinstalling the entire operating system? Thanks.

Is there anyone who knows the networking workings in Leopard to help me identify the problem??
I have no modem problem, since I can use the same system in dual boot with Windows XP. The problem must be a file or a setting in Leopard that is blocking my connection to the internet.
I dunno, it could be related to Java or how some scripts are executed by the operating system.
If I don't solve this one, I'll have to reinstall the whole system again. Come on, help me guys!

Dual-Boot; Restart and boot other o/s USB devices not working

I have issue with my msi z97-g43 mobo and Windows dual o/s PC.
Booting with win-8.1, USB devices working very well.Restaring windows 8.1 have NOT any issue.
After shutdown & start PC, choosing to boot windows 7 on bootmanager, USB devices not working in Win-7.
System no hang or occur any error/BSOD message.All startup programs run as normal.
I tried to re-plug usb devices but notting happens... Still not working
But after the win-8.1 shutdown, if i switch off PSU power button, watting ~1 munute for discharge.
After power up PC and boot with windows 7 all usb devices works normaly.
I checked all internal connections. 2 times disassembly all hardware and re-built system, nothing changed.All windows updates and latest drivers installed.
I'm sure other H/W is OK, but I thnik this mobo have a fault.

Thank you for reply.My PC system specs:
CPU:    Intel Pentium G3258 3.2ghz
Board:    MSI Z97-G43 /Bios: Ver. V17.7
MEM:    G.Skill Ripjaws 2x4gb DDR3-1600mhz cl9 1.5v F3-12800CL9-4GBRL
VGA:    Sapphire AMD Redeon HD6670
CASE:    Zalman z3 plus white (5x 120mm fan)
PSU:    Thermaltake Litepower 500w (12v1+12v2=36amp)
HDD-1:    Seagate 1TB ST1000DM003 /HDD-2: Seagate 2TB ST2000DM001
COOLER:    Akasa 92mm PWM Blue Led
OC:    CPU:Default /MEM: X.M.P mode=1600mhz 9-9-9-24-2t 1.5v
O/S:    Win7 x64 PRO + Win8.1 x64 PRO (Genuine)
All hdd's have MBR based partition table.Windows 7 & 8.1 installed in non-efi mode.In BIOS Boot sequence is setting up to non-efi Boot(system) drive as primary.
Before I suspect maybe have a short circuit to pcb or similar thing cause this issue.I take out all parts outside the chassis, and ran this system on the antistatic bag and box.Nothing has been changed.
I have Cooler Master Devastator(MB24 + MS2k) USB keyb+mouse set and tplink wn722n usb wireless dongle.
I have one more pc,based on AMD 970+SB950 chipset mainboard and AMD CPU.I exchange all parts to this amd mainbaord and tested for faulted hardware.All intel system H/W's is ok.All works great
Dual boot works perfectly.Not needs to switch off psu/power back and run system again.
I think msi z97-g43 mainbıoard have a problem.

N73 ME not working in Network Mode GSM and Dual Mo...

Dear All,
I have N73 ME.
Firmware: V 4.0812.4.2.1
I am using Vodafone Line and I am living in egypt.
I have a problem with the network of the device. The device is working fine only with the Network Mode UMTS, but not working with GSM and Dual Mode, which makes it doesnot have network signal in many areas, while I have another Nokia 5200 phone whick works fine in these areas.
Is it a Software or Hardware problem?
and what is the solution for it?
Thanks in advance for your help.

moderator note:
please be informed that your personal and contact information, as well as the IMEI of your phone are not allowed to be posted in this board for security and privacy reasons.
thanks.

Hello, I am trying to upgrade to yosemite, but I get the "disk cannot be used to startup your computer" error. Resizing the partition does not work, I get the error "MediaKit reports no such partition" probably because I installed linux in dual boot

Hello, I am trying to upgrade my macbook pro to yosemite, but I get the "disk cannot be used to startup your computer" error.
Resizing the partition does not work for me and I get the error "MediaKit reports no such partition" probably because I installed linux in dual boot and the disk manager is lost.
Anyway to tell the yosemite installer that it should not pay attention whether the disk is bootable or not ?
If I am doomed, any way to delete the installer and downloaded OS from my hard drive ?
Thanks for your help

As usual, the Linux installer wrecked the partition table. You would have to boot from your OS X installation disc and repartition. Doing so will of course remove all data from the drive, so you must back up first if you haven't already done so.

Dual 9800GTX+'s not working

Similar Messages

Maybe you are looking for