Dual band router that ipad will stay connected with

Is there a dual band router that ipad3 will stay connected to

My son-in-law uses a Netgear model WNDR3700-100NAS Dual Band Router. I just bought one but it hasn't arrived yet. This router is compatible with the iPad: 802.11a/b/g/n, supports 2.4 GHz and 5 GHz, supports WPA2 encryption.
I have ATT UVerse, but the UVerse router range is quite low. I bought a wifi repeater, which increases the range somewhat. The output from the UVerse will be plugged in to the Netgear router.
 Cheers, Tom

Similar Messages

My Ipad will not connect with Itunes prompt states this Ipad cannot connect because the Apple mobile device service has not started "??s "This Ipad cannot connect

my Ipad will not connect with Itunes prompt states this Ipad cannot connect because the Apple mobile device service has not started "??s "

Try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until the screen blacks out or you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.

Cisco 2500 dual band router. the hp printer is connects on one band, pc the other help

Cisco 2500 wireless router Dual Band N, HP PhotoSmart C309-g, Windows 7
PC cannot find the printer because it connects on a different band. Cisco uses the same name for both bands. How do I get both devices on the same network.

I also have a dual band router, Cisco's LinkSys EA3500 N750; and the 5.0gHz band is necessary to avoid interference with other equipment operating on 2.4gHz. I put TP-link 2.4/5.0 gHz adapters on each PC (one HP another Sony, both a few years old) and the PCs now work fine, no loss of internet/network access. Would that solution also work for the printer? The printer does not recognize any network (even though the 2.4gHz shows as available and strong on the TP-link device. I used the same name and security code for the new router as the old; again, neither PC had a problem finding it.

Alternative simultaneous dual band router that supports NTFS?

I was totally smitten with my Airport Extreme, until I had to change all of my media hard drives to NTFS (they had hit the characters per directory limit that FAT32 has).
I need to keep them as NTFS, because my TV only reads FAT32 or NTFS hard drives (i.e. I couldn't change to HFS+)
So my question is, does anyone know of a simultaneous dual band router (5ghz + 2.4ghz) which has gigabit ethernet ports and a USB port which supports NTFS hard drives?
From researching, the big competitors are the Linksys WRT610N and the Netgear DIR-855. Problem is, the Linksys and Netgear support forums are filled with posts from people claiming NTFS hard drives either don't work at all, or are severely temperamental
I could go for a NAS, but I just managed to get a pair of 2TB Western Digital USB hard drives for £98 each. I've been unable to find a 2TB (single hard drive) NAS for less than £170.

Can I use my wireless or an extra router along with the Verizon provided router?

HT204387 My iPad will not connect with my HTC phone even though it is paired.

Even though I have accepted the pairing the iPad will not connect to the phone.

iOS devices haven't been designed for data transfer wirth Bluetooth.
Check out this for more info: http://support.apple.com/kb/ht3647

IPad will not connect with extended network and/or guest network

I have extended my main network (AP Extreme) with an AP Express and uses a guest network too, all Macs, PC's, iPhones, game consoles, mediaplayers can connect to the internet with both networks. Only one device does not work with the main network and that is the iPad (1st gen). It can connect to the guest network, though. If i disconnect the Express, the iPad can connect with the main network or if I set the guest network to off it will too. But I want to connect to the main network (remote access).
Device.                          Network.          iPad internetconnection
Extreme.                        Main.               Yes
Extreme + Express.       Main.               Yes
Extreme.                        Main + guest    Yes both
Extreme + Express.       Main + guest.   NO
I have reset the network configurations on the iPad and it works for only one time, if the iPad goes into sleep mode and restarts, the connections is lost. The iPad seems to be connected with the router/AP but no internet access.
Fyi
- all devices have a fixed IP address dedicated by the Airport. i tried to use DHCP, but no difference
- radio channels on automatic
- all on 2,4 GHz band
IS THIS A IPAD 1 ISSUE and do I have to accept the fact that Apple does not support the iPad 1 anymore?
Any suggestions how to fix this? Thank you.

Thank you for the suggestion.
The name of my home wifi network is automatically found by the iPad and after I select it the iPad asks for a password. I have typed in my password that I use with my laptop, but it does not work.
I also tried the two alpha numeric 13 digit strings on my router. It is actually a Belkin. Neither of those worked either.
finally, I went into general as I could not find settings to tell the iPad to forget network settings?

Is it possible to extend AP Extreme's both main and guest networks by connecting one or two new dual band AP express in roaming mode (connecting with ethernet)?

I have an Airport extreme base station which creates a wireless network and a guest network at my home. Neither of them reach every room so I have set up one Airport express (1st generation A1264) in roaming mode to extend the main wireless network by connecting the base stations with ethernet (with powerline adapters actually). Works fine with the main network. However, I would like to extend also the guest network. Is this possible with a 2nd generation dual band AP express?

I would like to extend also the guest network. Is this possible with a 2nd generation dual band AP express?
Yes it is, if you have updated your Mac to use AirPort Utility 6.2 and both the AirPort Extreme and AirPort Express have been updated to use version 7.6.3 firmware.

HP Officejet Pro 8620 e-all-in-one printer & dual band router

Hi, I'm hoping someone will be able to confirm whether this printer is compatible with my router which is a dual band 2.4 GHz and 5 GHz. I am not able to connect it to the internet. The box says that the printer is compatible only with 2.4 GHz routers. Would the fact that my router is dual band mean that it will not work with the printer?

Hello @JMHouston , and welcome to the HP Forums, I hope you enjoy your experience!
I see you are looking into your options for a dual band router. I would love to help.
The printer will only connect to a 2.4 GHz broadcast. To quote this document on Print | Rate this content HP Printers - Tips and Workarounds for Common Wireless Network Printer Iss...
Dual band routers provide both 2.4GHz and 5.0GHZ frequency ranges. HP printers connect to the 2.4GHz frequency band and the 20 MHz bandwidth only. Many dual band routers let devices connected to the 2.4 GHz band communicate with devices connected to the 5.0 GHz band. But not all routers support this feature.
To manage the different bands and what devices connect to each, try assigning a unique SSID (network name) to each band. For example, name the 2.4 GHz band to “Mynetwork” and the 5.0 GHz band to “Mynetwork-5G”.
Communication and connectivity issues might occur with the printer connected to the 2.4 GHz band and the computer connected to the 5 GHz band. Try connecting the computer to the 2.4 GHz band.
As long as your router is broadcasting both network channels, you should have no issue connecting.
Please let me know if you have any questions. Thanks for posting on the HP Forums!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

Connecting Harmony Hub to Apple Dual Band Router

It appears that the Harmony Hub only connects to 2.4 ghz and my dual Airport Extreme, although it sends out both 5 and 2.4 doesn't work with it. If we can't find a work around one thing we are considering is whether we can add a second (2.4ghz only) router to the network either directly to the modem or as an extension of the network. I'm a little (a lot) over my head on this stuff so would appreciate any suggestions or approaches. thanks

Hi @SP-Michigan ,
I see that you are experiencing issues with setting up the printer over the network on the Comcast Dual Band Router.
I will do my best to help you.
Restore the factory settings on the printer.
Press the OK button on the printer, go to service, then select restore defaults.
Print a configuration page from the printer to make sure the IP and SSID are cleared.
Most likely it is the settings on the router that might need to be changed.
If it is set to 5 GHZ network you may need to change to 2.4 GHZ. (rename the 5ghz or shut it off)
You might also have to set it to WPA personal.
The WPA key setting needs to be on AES to work correctly not TKIP.
Multi casting needs to be turned on.
Firewall on router has to have open ports for printer.
If you have Mac Filtering you need to give printer hardware address from configuration page.
You might need to contact Comcast for further assistance to check those settings.
I have provided a document for setting up the wireless connection or you can follow my different methods provided.
Installing the Printer Software on a Wireless or Wired (Ethernet) Network.
If you need further assistance, just let me know.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Problem connecting 1525nw to Comcast Dual Band Router

I recently got a new Comcast Dual Band router. Since then I have not been able to connect my HP 1525nw wireless printer to the network. Have tried all methods, WPS, PushButton, Pin, installation thru HP drivers, resetting to factory defaults etc.......any suggestions?
BTW - the printer was connected earlier to the Comcast Single Band router. It used to work just fine then.

Hi @SP-Michigan ,
I see that you are experiencing issues with setting up the printer over the network on the Comcast Dual Band Router.
I will do my best to help you.
Restore the factory settings on the printer.
Press the OK button on the printer, go to service, then select restore defaults.
Print a configuration page from the printer to make sure the IP and SSID are cleared.
Most likely it is the settings on the router that might need to be changed.
If it is set to 5 GHZ network you may need to change to 2.4 GHZ. (rename the 5ghz or shut it off)
You might also have to set it to WPA personal.
The WPA key setting needs to be on AES to work correctly not TKIP.
Multi casting needs to be turned on.
Firewall on router has to have open ports for printer.
If you have Mac Filtering you need to give printer hardware address from configuration page.
You might need to contact Comcast for further assistance to check those settings.
I have provided a document for setting up the wireless connection or you can follow my different methods provided.
Installing the Printer Software on a Wireless or Wired (Ethernet) Network.
If you need further assistance, just let me know.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

IPad Air: stumped by streaming problem on dual band router

I have a dual band router at home. My iPad Air will stream very poorly when connected to the 5 GHz band. By streaming, I mean Netflix, Crackle, etc. Everything works fine if I connect to the 2.4 GHz band. The strange part is that my old iPad One streams fine from either band. Even stranger, downloading stuff like apps or magazines works fine with the iPad Air on either band. The problem is only with the iPad Air when streaming on the 5Ghz band. Any one else has this problem?

I am also finding streaming (from YouTube) to be poor both on wifi and 3G. My first gen iPad had a lot of problems, but streaming was never one of them. Signal strength is good and I haven't changed any network hardware or settings.

I have a dual band router. How can I tell if my iPad is using 2.4Ghz or 5Ghz.

I have a dual band router. How can I tell if my iPad is using 2.4Ghz or 5Ghz. I want to try and manage all the devices in the house over our WLAN. Thanks. Nik

I'm not really sure there is a way to tell, it certainly doesn't seem to be something you can set within the iPad so I'd assume that if a 5Ghz frequency is available it would use that, otherwise it would default to using a 2.4Ghz frequency instead. I'd also assume from having a 5Ghz router myself that there would be some sort of light on your router which will flash on/off when data is recieved so if iPad is your only 5Ghz device and it's sending/receiving data then this light should flash on your router.
Regards,
Steve

Ipad push applications on Apples Dual band router - Help

All, why are my push apps not pushing when I'm connected to the Apple dual band router, internet works fine though? Funny thing is at my moms house it pushes fine with her cheap netgear. Can someone with a dual band and push working on your iPad please provide what settings you used on the router ? Is it best to just a separate name for 5ghz ?
Its been so hard to find help on this. Thanks

I am also finding streaming (from YouTube) to be poor both on wifi and 3G. My first gen iPad had a lot of problems, but streaming was never one of them. Signal strength is good and I haven't changed any network hardware or settings.

Extend an AE dual-band router with a 2nd AE dbr: will automatic mode work?

I have a new Apple Extreme dual-band router, and it works just great. My N devices all get the maximum bandwidth, and the G devices connect easily as well. I have a section of my house that gets weak reception, and want to extend the network with a second router.
If I bought a second Apple Extreme dual-band router, and configured it to Extend Wireless Network and Allow Wireless Clients, could I then leave it on the default radio mode of Automatic? It seems like either router would then be able to tell if the wireless clients were N or G, but communication between the routers would be N. I want to keep the maximum bandwidth for my N devices.
Thanks in advance

I have a new Apple Extreme dual-band router, and it works just great. My N devices all get the maximum bandwidth, and the G devices connect easily as well. I have a section of my house that gets weak reception, and want to extend the network with a second router.
If I bought a second Apple Extreme dual-band router, and configured it to Extend Wireless Network and Allow Wireless Clients, could I then leave it on the default radio mode of Automatic? It seems like either router would then be able to tell if the wireless clients were N or G, but communication between the routers would be N. I want to keep the maximum bandwidth for my N devices.
Thanks in advance

Dual band router will fix interferences right?

So i got really bad download problems, and i think i narrowed it down to interference problems.
Probably baby phones or a wireless 2.4ghz phone from my new neighbours.
So if i get the WRT320N-EW Dual Band router and put it on 5.2ghz this should fix it right?
Thanks in advance.

Home wireless networks based on the 802.11b or 802.11g standards transmit their signal in a narrow radio frequency range of 2.4 GHz. Various other electronic devices in a home, such as cordless phones, garage door openers, baby monitors, and microwave ovens, may use this same frequency range. Any such device can interfere with a Wi-Fi home network, slowing down its performance and potentially breaking network connections.
One benefit of the 5GHz 802.11a WLAN devices is that they are not vulnerable to interference from other devices, because the 5GHz frequency range they utilize is not used by any other devices (at least for now).
On the down side, because of the type of modulation 5GHz wireless devices employ, their signals are more prone to be reflected and/or absorbed by materials in the home. This can have the same practical effect as active interference; that is, to weaken the signal, and reduce range and speed.

Dual band router that ipad will stay connected with

Similar Messages

Maybe you are looking for