Dual boot 10.3.9 and 10.5?

I have a 12-inch powerbook G4, and I'm still using OS 10.3.9 because my Pro Tools hardware and software don't support more recent versions of OSX. I'm starting to feel behind the times though, and I'd love to be able to use 10.5. Can I have both 10.3 and 10.5 on my computer? I'd like to use 10.5 for everyday things and then go back to 10.3 just on occasions when I need to use Pro Tools.
Is this feasible? How would I go about doing it? Do I need install discs for both versions of OSX? I have a pretty big external drive that I can use to store the data i have on my laptop while I work this out...
Thanks --
Joe

You can dual boot. I'd suggest getting an external Firewire (not USB) drive. There are two reasons for this:
1 - Firewire is noticeably faster (yes... I know USB 2.0 is faster in theory... but USB 2.0 has a lot of overhead that Firewire doesn't have. If you go google for comparisons between Firewire 400 and USB 2.0 you'll find that Firewire consistently outperforms by a wide margin. How wide of a margin depends on the type of test (e.g. was it one really really big file being transferred vs. lots of very tiny files, etc.)
2 - I think I recall that the PowerBooks can only 'boot' from external drives if they are Firewire. You might have to check on this... but I think you may find that booting from external USB is only supported on the newer Intel macs.
You can format and install the OS of your choice on the external drive. I know the modern Macs prefer that the drive be formatted with 'GUID' partition scheme. Older ones used APM (Apple Partition Map).
Once you've done that, when powering on your Mac remember to hold the 'Option' key down. This will cause the Mac to display all bootable devices (rather than just booting off the default device). You can then select the device (use the arrow keys to highlight the drive of your choice) and hit the enter key and it'll begin booting.
Although you have a laptop, I'd suggest that you get an external drive enclosure intended for desktops. That's because these have (a) their own power supply -- so they're not drawing power fro the Firewire bus, but more importantly (b) because they almost always have their own ventilation and fan. The portable external laptop drives are generally in small, sealed, fanless cases. That's fine for occasional disk use, but when running an OS off the drive it'll be under very heavy use and may get quite hot -- causing premature failure. Oh... reason (c) is that you generally pay a premium for the 'portable' design factor. Desktop external drive & enclosures are usually cheaper!
I own a Maxtor OneTouch III Turbo -- but I'm very disappointed that Maxtor/Seagate has still NOT released a working driver for Leopard (I have to boot Tiger to be able to change the raid configuration) after all these months -- and are silent as to the status. It's NOT ok for a backup drive company to not have a working driver for a major OS update and then remain silent about it to their customers.
I also own three 'MiniStack v2' drives from Other World Computing (macsales.com) and have been extremely happy with those.
If performance is a big concern you may wish to purchase an external drive enclosure that supports "RAID 0" (striping).
Regards,
Tim

Similar Messages

HT3986 i made a dual boot of windows 7 and mac os x lion in my macbook pro .i installed microsoft support software also. now, can i install windows updates? do i turn on the automatic updating of updates?

i made a dual boot of windows 7 and mac os x lion in my macbook pro .i installed m icrosoft support software also. now, can i install windows updates? do i turn on the automatic updating of updates?

yes you need the updates and patches.
Only some of the drivers that Windows will automatically install at times
and always make sure to insure it is using restore points
do all the maintenance andsuch as normal
use MS Security Essentials for AV is really top notch
Clean disk space
Use WinClone new program to inisure you have a restore image

I kept a dual boot of windows 7 and mac os x lion in macbook pro. so, should i keep antivirus for windows 7? which is prescribable between bit defender(bd) and microsoft security essentials(mse)?does bd and mse un-installs easily?

i kept a dual boot of windows 7 and mac os x lion in macbook pro. so, should i keep antivirus for windows 7? which is prescribable between bit defender(bd) and microsoft security essentials(mse)?does bd and mse un-installs easily?

lower your font size unless you have difficulty
MS Security Essentials is excellent
Then again maybe time to investigate Windows 8 RP (which uses Defender)

I made a dual boot of windows 7 and mac os x lion in my macbook pro .i installed m icrosoft support software also. now, can i install windows updates? do i turn on the automatic updating of updates? does hot fix of microsoft helps in stop freezing?

i made a dual boot of windows 7 and mac os x lion in my macbook pro .i installed m icrosoft support software also. now, can i install windows updates? do i turn on the automatic updating of updates? does hot fix of microsoft i.e, " support.microsoft.com/kb/979491" helps in stop freezing in dual boot mechanism?

Windows has a software updater built into Windows and when you install the Boot Camp drivers then it will install an Apple software updater also. I believe Windows is set to automatically download and install your updates as does the Apple software Updater. They both will update the individual files it needs to periodically.
"Microsoft updates" and "Windows updates" are basically the same thing in Windows. Are you talking about the "Windows support software" when downloading from Boot Camp Assistant? Apple installs a software updater for it's Boot Camp drivers in Windows 7 so you can do it manually or automatically.
The "Hot Fix" your referring to is only for certain motherboards built from other Windows only computer manufacturers and does NOT pertain to any Apple computers.
If you have a problem with your computer then it's best to ask a specific question so we can help better.

Dual boot Mac OS X and Arch: Arch installer cannot find CD drive?

Hi, everyone! A friend convinced me to install Arch about a month ago on my desktop and I've loved it so much that I want to dual boot Mac OS X and Arch on my Macbook Pro 7.1.
So I have a Macbook Pro 7.1. I have partitioned the drive in Mac OS X and installed rEFIt. I have the Arch x86_64 disk which I know works because I installed Arch on another computer.
When I boot from CD I get the familiar Arch screen with options "Boot Arch Linux, existing OS... etc." I click boot Arch, and it starts to load. However, it says "Waiting 30 seconds for device /dev/disk/by-label/ARCH_201005 ... ERROR: boot device didn't show up after 30 seconds... Falling back to interactive prompt. /bin/sh: can't access tty; job control turned off."
After searching around the forums, some people said they had similar problems attempting to install via USB. I used "cat /proc/scsi/scsi" and my CD drive does not show up in ramfs.. What can I do to install this amazing OS on my MB Pro 7.1?
Thank you for your time!

Solved! sledgehammer and MrE (sorry, I can't spell it) in IRC helped me out. I had to download a newer iso that offers better Mac hardware support. 2010-12 iso

Dual booting between Solaris 8 and 10

Hi,
We mostly use Solaris 8 for testing which means I can't uninstall it. How would I be able to dual boot both Solaris 8 and 10 on a SUN SPARC machine? Is there a boot loader available like grub?
Please help.
Thanks alot!
Till later,
Joseph.

SPARC doesn't need a split boot loader like BIOS/x86. The OBP can directly load from any slice. So 'boot disk:a' would boot from slice 0 and 'boot disk:g' would boot from slice 6.
Darren

Dual boot Windows 7 (64) and Arch Linux (64) problems

Hello:
I am new to Arch Linux and just finished installing the 64bit on my laptop. It had a prebuilt Windows 7 (64) installed which I kept but split the hdd from 160Gb to 80Gb and 80Gb. I installed Arch there and set 4 partitions, all of them as Logical - a 64 MB ext2 /boot partition; a 512 MB swap partition; a 15 GB root partition; and the rest as my /home partition. My partitions look like this:
Disk Drive: /dev/sda
Size: 160041885696 bytes, 160.0 GB
Heads: 255 Sectors per Track: 63 Cylinders: 19457
Name Flags Part Type FS Type [Label] Size (MB)
sda1 Primary Unknown (27) 12889.02
sda2 Boot Primary NTFS 106.93
sda3 Primary NTFS [] 73915.11*
sda5 Logical Linux ext2 65.81*
sda6 Logical Linux 509.97*
sda7 Logical Linux ext2 15002.92*
sda8 Logical Linux ext2 57549.55*
The install was succesful(this was running from the core install cd) and I installed GRUB to my /boot but when I restarted it loaded Windows 7. I have used Knoppix USB disc to boot and see my Arch Linux install files and edited the /boot/gur/menu.lst file.
In Windows I installed EasyBCD 1.7.2 and tried to get NeoGrub bootloader working as a dual boot. I tried getting rid of the boot flag for Windows with cfdisk and setting it to my (Logical) sda5. That did not work. So far the only way I have booted into my Arch Linux install has been by going to the Live CD, choosing "Boot from Existing Linux Install" and editing the command files there.
root (hd0,4)
kernel /vmlinuz26 root=/dev/sda3 ro
initrd /kernel26.img
My goal is to get a dual boot working for Windows 7 and Arch Linux 64 and continue installing the Xorg and KDE to Arch. I just don't know what the problem is here. I don't mind reinstalling Arch if something went wrong, but I would like to keep my Windows running in order and add Arch on.
Any help would be greatly appreciated.

I ran the LiveCD and chose "Install to MBR hd0". I ended up with this:
setup hd(0,1)
Checking if "/boot/grub/stage1" exists.....yes
Checking if "/boot/grub/iso9660_stage1_5" exists.....yes
Running "embed /boot/grub/iso9660_stage1_5 (hd0,1)".....failed(this is not fatal)
Running "embed /boot/grub/iso9660_stage1_5 (hd16)".....failed(this is not fatal)
Running "install /boot/grub/stage1 d (hd0,1) /boot/grub/stage2 p (hd0,1) boot/grub/menu.lst".....failed
Error 31: File is not sector aligned
My entry for Windows into the menu.lst looks like this:
# (0) Arch Linux x64
title Arch Linux x64
root (hd0,4)
kernel /vmlinuz26 root=/dev/disk/by-uuid/3841273c-d91e-41d6-9dbf-716a15d03a01 ro
initrd /kernel26.img
# (1) Arch Linux x64
title Arch Linux x64 Fallback
root (hd0,4)
kernel /vmlinuz26 root=/dev/disk/by-uuid/3841273c-d91e-41d6-9dbf-716a15d03a01 ro
initrd /kernel26-fallback.img
# (2) Windows 7
title Windows 7
rootnoverify (hd0,0)
makeactive
chainloader +1

Dual Booting with Windows 8 and 7 Pro in a G6 - 2235us Notebook

I have a G6 - 2235us Notebook 64 bit that came with Windows 8.0 installed.
I would like to install Windows 7 Pro and make it dual book with Windows 8.0 with 7 as the default to start.
Would you please give me steps as to how to proceed and also the drivers, etc I would need to download.
Thank you.
This question was solved.
View Solution.

Thank you Paul. I understad I just have one more question:
I found this page that gives info about dual booting:
http://www.pagestart.com/win8dbwin701181301.html
From your expertise, would you say the steps suggested on that
page could succeed for making Win 8 and 7 dual boot in this particular machine?

Dual boot WIndows 8.1 and Windows 7 (32 bits) from separated disks gives error 0XC0000359

Hi all,
I have two disks, each with a (OEM) installed OS on it, a Windows 8.1 (64 bits) and Windows 7.0 (32 bits). The later came from mine old computer that unfortunately died to soon. So I have two disks and two OS in an brand new machine (with UEFI BIOS etc.).
Installing a dual boot option was a pace of cake. However booting into Windows 7.0 gives following error:
"Windows failed to start. A recent hardware of software change might be the cause.
File:\Windows\system32\winload.exe.
Status: 0XC0000359
Info: the application or operating system could't be loaded because a required file is missing or contains errors".
There is lot discussions about installing two OS but that is not mine problem: both are already installed.
Also there is much rumour about the UEFI BIOS and support for older systems. In mine medion computer the Security Boot option is disabled (by the OEM), so booting from a old BIOS should be possible, must isn't.
Someone advised me to run the recovery disk (of Windows 7.0) and run Bootmgr. However the system refuses to boot from CD/DVD with the recovery disk of Windows 7.0 inserted, booting from the recovery disk of Windows 8.1. goes fine.
Removing the disk with Windows 8.1 installed on it and directly booting in Windows 7.0 fails too with the message: "Reboot and Select proper boot device or: Insert boot media in selected boot device and press key". Also in this case the system
refuses to boot from the Windows 7.0 recovery disk.
Could you please help me?

Hi,
To rebuilt boot loader, I suggest we can try following command when you enter Windows 8.1.
Run cmd as administrator and type following command:
BCDboot [Partition Letter with windows 7 installed]:\windows
Note: if you installed Windows 7 on Partition F, the command can be write as: BCDboot F:\windows.
Then, restart and boot into Windows 7.
What’s going on?
Kate Li
TechNet Community Support

SYSTEM RECOVERY (F11) is inaccessible after dual-booting Windows 7 and Windows 8.

I dual booted Windows 8 with Windows 7 and now the RECOVERY partition (F is not loading upon pressing F11. It gives me the boot configuration data error. I have it marked as Healthy (Primary Partition) and I am able to access the files via. My Computer in both OS, but not through F11 System Recovery.
The bcdedit log is here: http://pastebin.com/b0Y5Hd1F
My partition letters:
C: Windows 7
D: Windows 8
F: RECOVERY
H: SYSTEM
In Visual BCD, One WRE is set to D: and the other is set to F:. Should i set both to F, which is the actual RECOVERY partition?
[2] The UEFI boot setup is unable to create HP_TOOLS parition because 4 partitions already exist. I don't remember having the SYSTEM partition earlier so maybe that repalced HP_TOOLS?
[3] When I try to create a recovey media, the orange circle filter keeps of going even after I have inserted the an external USB hard drive for it to detect. Does it usually take this long? I am guessing once the recovery media is made I could do system repair from there and get RECOVERY to work?

What is the p/n? Remove the battery and look for it. Post all alphanumeric characters.
CTO means configure to order. That means only you and HP know the notebook's configuration.
The problem you are going to run into is that there is a maximum of four primary partitions allowed by Windows. That is by design. It appears that you removed the HP_TOOLS partition, which was a requisite for the UEFI diagnostics.
Frankly it looks like what you will have to do is put the UEFI environment on a USB stick.
I would create the recovery media on a high quality 16GB USB drive.
The partition schema must be as follows:
1) C: (NTFS)
2) HP_Tools F: (must be FAT32)
3) RECOVERY D: (NTFS)
4) SYSTEM (NTFS) created by the Windows install process
I am not aware of a dual-boot or more schema that allows a UEFI environment with the Recovery Manager accessible from F11. I wish I had better news for you. Perhaps our forum Provost DavidPK knows how it can be done.
I do recommend that you copy the RECOVERY partition to an external disk for safety sake.
If you are able to boot into the recovery manager I strongly suggest that you create your recovery media. If you do not do that you will not have a copy of your operating system and drivers for a plan B. I did not go with the option you used and did not create problems to deal with later.
When I play around with my loaner notebook and configure it to dual/triple boot, I always install a different hard disk and put the original one aside. You can still return your system to its original configuration and then take the hard disk out and use another one to play with. I believe that would be the wisest path to follow.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Dual boot with Windows 7 and LINUX - Tecra A11 (PTSE1A-00L005)

Hi,
I bought a new Tecra A11 Laptop which runs WIN7 Pro. I want to install LINUX also. That means, I want to run my laptop in dual boot Win7 Pro/LINUX (any distributor). Please tell me how to do that.
There are 5 partitions on the HDD:
1. Active, Recovery partiton 1.46 Gb (no drive letter)
2. Active Primary C: Boot 145.04 Gb (NTFS)
3. Active Logical E: 78.13 Gb (NTFS)
4. Active Logical F: 64.25 Gb (NTFS)
5. Primary Partition 9.2 Gb (no drive letter, application unknown)
Hey, I need it badly, because I have admitted to a course of RHCE (Red Hat Certified Engineer)
Please help me

Hi
I may not be able to give You a step-by-step explanation but most distros today offer a possibility to co-exist with Windows.
During the installation the unused free space will be taken by Linux (with the consent of the user of course!!)
What exact setup is needed by You is impossible for anyone else to say, but I would suggest to make the space occupied by the F drive available for Linux.
You seem to have space enough for Windows and the Linux OS does not need much.
Some thoughts concerning your partition setup:
I would NOT touch 1,2 and 5 no matter what. They are your system and some system internal partitions (recovery environment and data) and would not be fun to lose.
1. Active, Recovery partiton 1.46 Gb (no drive letter)
2. Active Primary C: Boot 145.04 Gb (NTFS)
3. Active Logical E: 78.13 Gb (NTFS)
4. Active Logical F: 64.25 Gb (NTFS)
5. Primary Partition 9.2 Gb (no drive letter, application unknown)
So pick a Distro (my suggestion Ubuntu, Mint, Fedora, OpenSuse - Fedora will be the one closest related to RedHat) which will guide You through the steps to allocate space for Linux.
I would suggest however to remove the drive F in Windows so Linux does not start resizing all partitions.
I am sure that will work fine, but will just take time and the pretty unnecessary F drive will most surely be kept.
If You already have valuable data on your unit, make sure to back it up!! No software comes with warranties :)
Last but not least - make 100% sure to create a recovery set with the help of Toshiba Recovery media creator BEFORE you start installing Linux.
If something goes wrong You might want to have the possibility to put the unit back into factory state.
Good luck and keep asking if You need additional help!
Tom

EFI partition deleted after removal of dual boot of OSX10.8 and Ubuntu/Linux Mint - using rEFIt

so, i recently installed ubuntu to check out the advances in the linux world since i last looked into them 10+ years ago... very impressed, but when i tried to delete ubuntu and remove the various partitions (which i was able to do just fine using gparted) reFIT still displayed the **** linux logo from the install i deleted....
OSX still boots fine... a install of Linux Mint i have on another partition(s) still boots fine ... everything appears to work... but i want to know what the possible issues are so i can be prepared...
this is frustrating...
so i went in and looked around with the remaining partitions and noticed the EFI partition which hadn't shown before i mistakenly tried to install another distro over ubuntu after wiping the partition it was on...
so i erased the EFI partition hoping that this would remove the g-damned hold out linux boot logo in reFIT... it didn't... now i suppose i can go back in and create a new EFI partition through gparted but that stupid linux logo will still be there... and i'll have another problem of getting the proper information back onto the EFI partition, which i am unsure of how to do, or where to even dig up the proper information...
i want to edit my boot mbr or grub or whatever the eff apple comps use as a boot record so that (or i am using as a boot record since i'm using reFIT) to get rid of this **** logo, so i can install another distro of linux and probably windows without having the **** supernumerary logo...
i would rather not wipe the whole drive (aka the primary partition the recovery partition) and do a fresh new install of os x (mountain lion) because i have OSX set up just the way i want it for personal use and work use... all my various tools and so on...
i don't use time machine and can't do a "restore" from a previous back up...
some one please help me out here, what are my options? am i going to have to bite the bullet and do a wipe of the entire drive and all its partitions to get my MBP back to 'normal'???
PS - using a macbook pro late 2011, standard specs, 13"...

stqn wrote:
Expi1 wrote:Thanks, I'm mostly struggling with how to partition for Arch and then how to do the bootloader. I'm using Win8 64-bit and from what I understand a Legacy BIOS bootloader. I'm not entirely sure what I should be partitioning the C: into, I've done partitions before, just not for Arch and then I'm not sure whether to use GRUB or syslinux, or if I even need those. Or if I need to use GPT or MBR?
Your disk is already partitionned so you don’t have to choose between GPT or MBR, the choice is already made.
You don’t partition “C:”, that is the name of a Windows partition. You partition a drive.
Grub or syslinux, use whatever the beginners guide tells you to. Personally I think syslinux is simpler which is why I’m using it (but I’m not dual-booting, if that matters).
You’re not saying what your problem is with partitionning, so it’s hard to help.
Thanks for getting back to me, I'm not sure if I just create one large partition for Archlinux or if I have to create multiple? Where I'm also confused is with the Creating Filesystems part of the guide. I don't understand how I'd do this in Windows, or what /dev/sda1 is referring to.
As for the bootloader part, the Beginner's Guide gives you a choice between syslinux and grub, what I'm not sure about is which to use considering I'm dualbooting. How it will affect my windows bootloader, do I disregard that and use GRUB now? I'm unclear on how that works.
I'm also aware I need to disable Secure Boot, I just searched my BIOS options and couldn't find anything remotely relating to that, so I'm assuming it's not an issue since this computer was originally on Windows 7 anyway?
Thanks again, Expi.
Last edited by Expi1 (2014-03-06 19:54:30)

Dual boot Win7 pre-loaded and XP

I have a T510 that came pre-loaded with Win7 Professional. I'd like to dual boot with XP that I have loaded on a different hard drive on the same T510.
I do have the recovery disks. I can't do a fresh install of XP because it have over 300 programs installed. Is there some way to run the recovery disks with Win7 Pro to not format the XP partition. Can I make the XP partition read only and then run the recovery disks?
Maybe someone knows of a way to install the recovery disks, then ( I know how to move Win7 and make a partition before Win7 then restore XP to the hard drive) then repair Win7 so it has the correct drive letters.
Thanks,
Docfxit

Docfxit wrote:
That's a good idea. I might end up doing this. The problem I have is I can't get all the Lenovo setup/programs that come with the restore disk to load. I know I can get some of them loaded with System Update.
What setup/programs will you be missing? I run a vanilla WIn 7 Pro 64 on my T400 and used TVSU to pull down everything that I need.
It may be that some multimedia stuff will be missing, but grab the installers for them from your Lenovo Win 7 setup before wiping it or removing that drive. Probably in C:\SWTOOLS (at least they were there in the old days. I don't have a Lenovo '7 load to examine.)
I'd probably do something like this, since I can't resist messing with a multiboot machine: clone the XP install to a large HD - or use the one you have if it 's big enough. Shrink the XP C: partition with your favorite tool. Fire up a MS '7 install DVD and install into the free space. I'm told you can use the Win 7 activation code that came w/your machine, but you may have to call MS.
Install TVSU for Win 7 and let it pull down the rest. Come to think of it, that's what I did with my XP T61.
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Satellite L500/013 - How to make dual boot of Windows 7 and XP?

Hi
I just bougth my first Toshiba laptop, it comes with Windows 7 Professional pre-installed. Before I start spending hours on this, I am just wondering if this can be done:
1) I would like to use the Windows 7 Professional in 64 bit mode and then
2) Create second partition on HD to install Windows XP 32 bit on it.
Just wondering about if this is possible and what is the recommended sequence for the install is. First thing I need to do is to create recovery disk for Windows 7, so I assume I need to configure Windows 7 first?
Thanks for any help
Thomas

> First thing I need to do is to create recovery disk for Windows 7, so I assume I need to configure Windows 7 first?
Well, this is strongly recommended!!! Before you would do anything with your HDD you should create the recovery disk!!!
Im not quite sure how you could set up an dual boot using Win 7 because I didnt try this but I did it using Vista.
First of all you have to create an second partition in Vista. This could be done in Disk Management.
Then I installed Win XP on the second partition. But after the XP installation I could not start Vista because Vista boot manager was damage by Win XP.
To fix this I have used a original Vista disk (not recovery disk). I booted the Vista DVD and this has repaired the Vista boot manager. In Vista I have installed EasyBCD.
EsayBCD is a small tool which helped to add the Win XP to the Vistas boot manager.
After new reboot Vista and Win XP appeared in the boot manager and I could choose between both OS.
I think you will need the same procedure using Win 7

Dual boot drive - Mountain Lion and Snow Leopard - Correct order to load software /apps?

Hi
I want to create a dual boot drive for Mountain Lion and Snow Leopard as some of my hardware (is not supported in Mountain Lion).
I am happy how to do this, I just want to know if there is a correct way to install software and apps.
My plan was to do a clean install of both using two partitions, the larger going to ML and smaller one for SL. I was going to install SL from the DVD and then after updating from 10.6. to 10.6.8 and download ML from the app store and install on the larger partition.
Do I install all the software I use like Final Cut, Aperture, iLife (for Garageband) etc on the ML or SL partition or on both. Also, is there a better way / practise of the order software updates / apps and boxed software should be installed when doing a clean machine install.
Thanks in advance.
Matt

Thanks mende1
So, if I have software I need to use on both ML and SL - for example Final Cut as I have a Canopus AVDC box which is not supported in ML but only SL, do I need to install the same software in both OS?
I usually open apps using spotlight and didn't know if it would software / apps would open if already installed on the other partition?
Thanks again
Matt

Dual Boot with Snow Leopard and Mavericks not possible?

I have a Early 2011 Macbook Pro with 2,3 GHz i7 Quad and two 512 GB SSDs (the secondary disk in an optical drive bay enclosure). This Macbook Pro can run Snow Leopard and Mavericks on the primary disk without problems. When I try to set up a dual boot system however, problems appear and it looks like it is not possible. When I start from Snow Leopard, I cannot select Mavericks as a start volume and vice versa. The error message says something like "Bless tool" cannot use this disk, i.e. unmount and boot from it. The problem remains when I exchange the disks (putting the primary disk in the drive enclosure and vice versa). When I put the secondary drive in an external case however, it is possible to boot from it - but strange things happen when the system starts: My computer clock is reset to 1/1/2001, WiFI passwords are not remembered for more than one session, disk permissions are reported as "repaired" but do apear as not repaired when I check them again - and other issues). I have verified both disks already and repaired permissions but that does not change the situation. So my experience is different from what is said in https://discussions.apple.com/thread/566781. It looks like the latest Mavericks cannot coexist with Snow Leopard on neiter a secondary internal drive nor on an external drive. This is strange since both disks and systems work flawless when run alone. Any suggestions to solve this problem?

When I check the Mavericks disk in the optical drive with disk utility after booting / running Snow Leopard on the primary disk I get som errors, see below ("disk utility Info"). So after all, I decided to erase the disk and install Mavericks new. But even erasing the disk is not possible when it is in the optical drive enclosure. I get this error message:
"Volume Erase failed with the error:
Could not unmount disk"
When I put this disk into an external case connected via USB however, it starts and runds MAvericks without any Problem. Same happens when I put thie Mavericks disk into the internal primary hard disk place.
"disk utility Info" when verinfying the secondary drive in the oprical bay:
Verifying volume “Samsung SSD Daten”
Performing live verification.
Checking Journaled HFS Plus volume.
Checking extents overflow file.
Unused node is not erased (node = 40)
Checking catalog file.
Unused node is not erased (node = 30)
Checking multi-linked files.
Checking catalog hierarchy.
Checking extended attributes file.
Unused node is not erased (node = 8)
Checking volume bitmap.
Volume bitmap needs minor repair for orphaned blocks
Checking volume information.
The volume Samsung SSD Daten was found corrupt and needs to be repaired.
Error: This disk needs to be repaired. Click Repair Disk.
Verify and Repair volume “Samsung SSD Daten”
Error: Could not unmount disk

Dual boot 10.3.9 and 10.5?

Similar Messages

Maybe you are looking for