Dual G5 2.0 Power Mac (June 2004) referb - booting problem

Hi all - my dual G5 2.0 Power Mac (June 2004) decided to rev its fans and boot no more. When I push the power button in front, the white light comes on while pushing it, then goes off, yet I hear the fans starting, the hard drive spinning etc. The key board isn't getting power (the caps light doesn't go on) and after a few minutes the fans rev like a jet engine...starting slow then gaining speed. I can't open the DVD from the key board (have tried all usb ports). Have also looked through this discussion area and tried many of the solutions provided (reset the PMU, unplug, try different outlets etc.) Any help would be appreciated. I do have Applecare but they are closed for the night.
Thanks for you help
Dual G5 2.0 (June 2004) referb from Apple   Mac OS X (10.4.6)  

Your OS is not loading and the fans default into a speed up mode.
Power up and hold down the mouse button, the cd tray will spit. Insert Tiger/install disk and power boot holding c. (note: use a wired keyboard/mouse directly to the machine and nothing else for now)
In the Installer, select Disk Utility from the menu>Repair disk/permissions. note any errors you see.
If you can't access the drive, it might be dead. I hope you backed up files.
All you need to do is get a new drive and reinstall Tiger etc.
If you can get a 6 pin firewire 400 cable to each Mac and t boot the problem Mac. the hard drive should appear on the other which you can recover files.
If the OS is fried you can do a archive and install too.

Similar Messages

  • I have a Power Mac G4 (2004) and want to transfer all my files to a new MacBook Pro 15.4". Can this be done thru firewire cable or do I have to transfer to an external Firewire 800 hard drive first?

    I have a Power Mac G4 (2004) and want to transfer all my files to a new MacBook Pro 15.4". Can this be done thru firewire cable or do I have to transfer to an external Firewire 800 hard drive first?

    Do it with a Firewire cable (buy a 800/400 adapter if you need it) - the USB transfer takes a much longer time.
    Start up your old PowerMac G4 holding down the "T" key, for target disk mode.
    On your new MacBook Pro open "Migration Assistant" in your utilities folder.
    Connect the 2 computers by firewire cable and follow the prompts in Migration Assistant.

  • Can I put a dual processor in my power mac g5 which only has one processor right now

    Can I put a g5 dual processor into my power mac g5? I have a power mac G5 but it only has one processor so I wanted to upgrade to the G5 dual processor found in the later version power macs. Would I be able to do this? If i could do this would i need another fan or other parts? I was also thinking of putting more ram in and another hard drive. PLEASE HELP

    Exactly what to do with ram and video is hard to say without the model details.  You can go to http://www.everymac.com and click on Power Mac G5 and then find the machine you have.  The detailed info on the machine will show how much and what type of ram you can put in (I always use ram from either OWC, http://www.macsales.com or Crucial, http://www.crucial.com) and also gives the installed video card info.  OWC would also be a good source to see what video cards are available that will work with that logic board.

  • Power Mac Lion Won't Boot! Fixes

    Ok, I have the following: 2 x 2.66 Ghz Dual-Core Intel Xeon Power Mac that had 10.6.8, 4 GB MHz DDR@ FB-Dimm Ram over 4 slots. I had the original hard drive (Western Digital Caviar SE 250gb Ram HD model #WD2500AAJS-41RYA0) drive in this morning, and cloned it to a Seagate Barracuda SATA 1 TB 7200rpm 32 Cache Hard Drive. When I formated the new drive, I did it journaled. I took out the Western Digital and made the Seagate Barracuda the boot drive. I also installed a second drive, a Seagare Barracuda SATA 2 TB 7200rpm in bay 2. That drive is not journaled since I am storing video on it. Both of the new drives were formated properly and without issue. They worked all day without issue. This evening, I downloaded Lion without issue. It installed and rebooted. Everytime the computer boots, it goes to the "you need to reboot screen" aka "Mac Kernel Panic Screen" with four languages. Here is a link to the image: http://support.apple.com/kb/TS3742. Any ideas of what is happening or what I did wrong? Any thoughts on what happened? Any fixes? Help please. Do you need any other information?

    OK. ALSO, I installed the OLD hard drive on its own and it boots fine. It seems like it can't find the new drive. Thoughts?

  • Power Mac G5 won't boot with Lion?

    After installing Lion, my early Intel 2010 Power Mac G5 won't boot. There were no problems for the first 2 days. The third day my G5 wouldn't boot at all. Not using Lion's recovery function, many attempts to boot from a previous system disk, and firewire target mode. The keyboard seems to be dead after attempting to boot except for the DVD eject key. All I get is a grey screen with an icon of a folder with a question mark within the folder. This icon blinks on and off continuously. Since the keyboard isn't working, I can't reset the PRAM, start in safe mode, or any other keyboard commands. The failed boot doesn't even get far enough for the Apple window to open. I replaced the hard drive and accomplished nothing except for spending even more money and time.
    This is VERY frustrating! Has anyone else had a similar problem with booting after Lion't installation??
    Thanks.

    1) you have a Mac pro Early 2009, remember this. It avoids confusion here in forum
    2) you're HDD's OS cannot be found by the firmware of the Mac hence it results to a question mark
    perform the following(recommended to use a USB keyboard)
    a) startup manager
    press and hold option on startup. Do u see your HDD?
    b) if you have a back up of your data then you can boot to the install disk and perform an erase and install
    repairing the permission will not work since the disc's OS is different from the HDD's OS.

  • Power Mac g5 hangs on boot up when hot

    My Power Mac G5 hangs on boot up when hot, such as after I have been using it a while. It won't get through the boot up process and I have a blank (dark) screen- no picture. Sometimes the little Mac chime sound doesn't even complete, and it quits abruptly 1/2 way through the sound.
    Once the machine cools it does start... at least so far.
    Any thoughts?
    keith

    Any Extra Ram, Extra Peripherals, Aftermarket Video Card?
    Will it boot with a CD?
    When was the last time you checked the RAM in "About this Mac?"
    Can you monitor internal temps thru software ?
    Possible bad ram, bad power supply, bad video card.
    Try removing an extra add-on components and see if that helps.
    Also, I've found startup freezes can corrupt HD start-up files badly.
    Just had similar issue in my single processor, ancient 1.6 Gig G-5.
    Bad Radeon Card. Put the original back in and it works fine.
    Google "G-5 Power Supplies" and check out the information....known issue.
    Good Luck

  • Power mac G5 2004 won't power on

    Hello all,
    my Power mac G5 June 2004, won't power on at all. I've changed the logic board, power supply, dual processors, front panel board, and front panel board cable. Still getting the same results. The only thing I could think of next is the power button.
    Please help!!!
    M-One

    m-one
    No more wise guy stuff then.
    If you have tried and thus eliminated everything else, then perhaps it is indeed the power button.
    However, are you perfectly certain that it can be nothing else? Were all of the parts that you used for troubleshooting purposes from some other Mac or from some kit or did you purchase them or what?
    Sometimes it can be more than one thing. And at different times. I am not sure exactly what the minimum configuration for a boot-up is but perhaps search for that and see what pops up. Reduce it to that and try it.
    If you have a working Mac from which these replacement parts are coming it is not high on my list of favorite strategies but you can try plugging the suspect components into the working Mac one at a time until you find the culprit.
    Are there any parts that you replace that require you to press the SMU reset although you have done it once? Perhaps a call to Apple or again search on that for suggestions.
    Luck-
    -DaddyPaycheck

  • Dual Layer DVD on PM G5 (June 2004)

    I have a Power Mac G5 (June 2004) and i'd like to upgrade it's Superdrive to a Dual Layer one. Do I have to buy one provided by Apple? Or there is another I can install instead?

    The Pioneer DVR-112 is a popular choice. It's available for about $30 here and other retailers.
    What drive do you currently have? Some, like the Pioneer DVR-117 are Apple-crippled to not burn double layer discs. The DVR-117 is actually a Pioneer DVR-108 that's had its DL burning capability removed in firmware.

  • Can I run Leopard OS X v10.5.8 on a Power Mac G5 (2004)?

    I am wanting to upgrade to CS5 but I see more and more people are having problems with Snow Leopard not running on the Power Mac G5 because of it not having an Intel Processor. Mine does have the Dual 2 GHz Processor is it able to run the new CS5 on Leopard OS X v10.5.8? Please advise and thank you for your help.

    Adobe CS5 requires an Intel Mac.
    That Intel Mac can be running OSX 10.5.8 and still run CS5, but it has to be an Intel machine.
    The good news is that even today's Mac Mini is likely a more powerful machine than the biggest G5 available (not just the faster CPU, but every single one of the sub-system components is significantly improved).  And the cost of a new machine isn't so bad, in the context of what Adobe charges for their apps.  Your best bet would be to start scouting around for a new machine that would be ready for CS5.5 when it starts shipping next month.

  • Upgrades For Dual 1.8GHz G5 Power Mac

    Hi
    I have just bought a power mac g5 and i am confused with what some of the other posts are saying about ram. The spec is 1.8 GHz Dual Processor, 1GB Ram (8x128MB Chips), 64MB graphics card. I am looking to upgrade my ram to at least 2 GB. Is the spec i need ddr pc3200 400MHz 184 pin, as this seems to be expensive? i am also looking at upgrading the optical drive so it can read/write dual layer discs, i have found 1 on ebay with lightscribe aswell. should this be ok?
    http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&ssPageName=STRK:MEWAX:IT&item=35 0227215181
    i am also after onboard bluetooth and wireless. i already have a d-link bluetooth usb but would prefer the bluetooth card and antenna. is it one combined card? is it possible to get a wireless n card with this model?

    If you want you can get some upgrades from OWC In wookstock, Illinois in the usa . I see you are from the uk that maybe to far for you .What do you want yo upgrade first . I would do the graphics card, but I would get the nvidia 6800 gt or better . they go for about 200 dollars in the us , I dont no how much thats in pounds . But www.owc.com is a good place to look and ebay .

  • OS 9 disks for 2002 dual 1 Ghz MDD Power Mac

    Hello.
    I own a 2002 MDD Power Mac - the 1 Ghz dual version -, but I don't have the original OS 9 disks. I'm from Romania, so it's quite hard to get hold of them. Is there a way that someone could help me? I'd really like to run OS 9 on the Power Mac, as my 333 Mhz iMac proves to be to slow.
    Thank you.

    You can call Apple Customer Support 1-800-767-2775, provide the Serial Number and specifications of the Mac, and for a fee, a replacement set of system discs (if available), can be ordered.
    However, the discs will be for the original version of OS, that was pre-installed, when the Mac was manufactured. In this case, it should include the OS 9.
    Do you want to be able to boot into OS 9.x, or run OS 9.x in classic mode while booted into OS X. If you want to boot, you'll need the CD. However, if you just want to operate in classic (no OS 9.x boot) copy the complete System Folder containing OS 9.2.1 or 9.2.2 from another Mac. Then copy the folder to your Mac. You should now be able to run in classic mode.
     Cheers, Tom

  • Installing an intel processor on a power mac G5 (2004) with mac os Xpanther

    Hi everyone,
    I really need some help, I need to update my Power Mac G5 because I discover that almost every single new upgrade for Final Cut Pro is for Intel Macs, so i would like to know if it is possible to install this processor to my oldie computer or can I upgrade my panther system to a leopard and being able to run the new programs??'. Thanks a lot
    Eugenia

    You can't install an Intel processor in your G5. For Intel you need to buy a new/newer Mac.
    Here's the *Mac OS X 10.5 Leopard installation system requirements*
    http://support.apple.com/kb/TA24950 To upgrade, you can skip Tiger 10.4.
    Recommend you increase RAM more than the minimum.
     Cheers, Tom

  • Power MAC G4 doesn't boot up, keeps shutting down.

    I have a Power MAC G4 dual 1.25 GHZ with mirrored bay doors. When I start the computer and it begins to rev up it shuts down. After several tries it eventually boots up, but when i go to restart, it shuts down. Any Feedback is this a major problem ?

    Stevink, welcome to Apple Discussions.
    Is this a new occurance? Are you using any wireless devices? After it eventually boots up, does it stay up for a long time?
    Some USB devices can cause the opposite - restart instead of shutdown. Don't know if your case could be caused by a USB device. What USB devices do you have connected? Disconnect all external devices except your monitor, keyboard & mouse. Now does it startup OK?
     Cheers, Tom

  • Power Mac G4 MDD Intermittent Boot from Internal HD?

    I have a Power Mac G4 MDD with a 1.42G Dual Processor, 2GB Ram using a 500GB HD operating OS 10.5.8 The problem I am having is that my computer will boot just fine for a week or so then all of a sudden it won’t boot up at all from the internal HD. Here are the symptoms; I get the ‘chime’, then the grey screen appears with the black apple logo and I see the ‘spinning gear’. The spinning gear stops (after about 15 secs) then it goes to a light blue screen and just sits there forever. I usually see this ‘blue screen’ for about 2 seconds just before my desktop appears on the screen during a normal boot. I could go home tonight and it might boot up just fine, I don’t know, but it’s very frustrating. Things I have tried – ( I have two MDD’s so it’s pretty easy to troubleshoot) but still no successful boot sequence.
    1. Reset PRAM
    2. Changed MOB battery
    3. Attempted a boot from another known good HD
    4. Removed the 500 GB HD and installed in another MDD and it boots every time.
    5. Replaced Motherboard with a known good spare I have.
    6. Swapped out RAM modules
    I’m not sure what’s next? Processor?, Power Supply??, Video Card??
    Maybe someone out there has seen or witnessed this strange occurrence on their MDD?

    I have not reseated ALL the connectors but I will try that first tonight. I removed the AC last night so when I get home I will power it up and try again. When I can get it to boot reliably, it's usually been following an AC outage overnight or a couple of days.
    Thanks,

  • Power mac g5 will not boot to dvd at all any ideas?

    Power mac g5 2.3 late 2005. Leopard 10.5 installed on drive and boots ok to hhd.
    how ever i need to go back to tiger 10.4.4 or later for my music hardware to work correctly..
    Sooo i purchased a Tiger 10.4 black retail disk and it will not boot to it in any way all I end up with is a kernal report screen.
    I have tried everything.. taking the drive out. adding a new formatted drive to install to.. no joy..just does not even look to be installing nothing..not even a spinning wheel thingy . if the disk was too early eg before late 2005 would it act like that and not install?
    I'm lost here lol.

    Hmmm, something else is going on I guess...
    The dvd is black with the X on it and has this number on it - 2Z691-5305-A
    Apple Mac OS X 10.4 Tiger (Full Install) DVD Retail Version
    Item #:
    MA453Z/A 1005166
    Compatible with eMac (2005), iBook G4 (Late 2004), iBook G4 (Mid 2005), iMac G5 17-inch (ALS), iMac G5 20-inch (ALS), iMac G5 (17-inch iSight), iMac G5 (20-inch iSight), iMac (Early 2006 17-inch), iMac (Early 2006 20-inch), Mac mini, Mac mini (Late 2005), Mac mini (Early 2006), MacBook Pro, Power Mac G5 (Early 2005), Power Mac G5 (Late 2005), PowerBook G4 (15-inch Double-Layer SD), PowerBook G4 (17-inch Double-Layer SD).
    Also...
    Mac OS X Tiger 10.4 Drop-in Install Hardware Bundle (CDVersion)
    Item #:
    2Z691-5306-A 1002481
    Compatible with eMac (2005), iBook G4 (Late 2004), iBook G4 (Mid 2005), iMac G5 17-inch (ALS), iMac G5 20-inch (ALS), iMac G5 (17-inch iSight), iMac G5 (20-inch iSight), iMac (Early 2006 17-inch), iMac (Early 2006 20-inch), Mac mini, Mac mini (Late 2005), Mac mini (Early 2006), MacBook Pro, Power Mac G5 (Early 2005), Power Mac G5 (Late 2005), PowerBook G4 (15-inch
    MA453Z/A 
Disc 1 - 2Z691-5306-A 
Disc 2 - 2Z691-5307-A 
Disc 3 - 2Z691-5308-A 
Disc 4 - 2Z691-5420-A 
Disc 5 - 691-5145-A, Ver 2.0 

The iwork cd is 603-6242.
    http://www.welovemacs.com/2z6915306a.html

Maybe you are looking for

  • Opening an URL via a button in a new browser window?

    Hello, I'm integrating now Oracle Reports in my HTML DB application. Everything work well. I have create a launching page with paremeter items and a button that call a branching of type "Branch to Function Returning a URL". This branching construct t

  • Question about FCP feature. (Not sure what they call it)

    Hello everyone, I have a question. A few times before I have done this thing on FCP where I get 2 clips and run them at the sametime and as they are playing I would click on the angle that I would like at that moment and so on. FCP would automaticly

  • I don't see the download button after I put in my redemption code.

    I have been trying to download photoshop after purchasing it at Best Buy.  I don't have a disk drive.  I put in my redemption code, but I don't see any download button.

  • Moving Time Machine Backup to Time Capsule

    I just bought a 1tb refurbished TC and am trying to figure out how to move my backup files from my FireWire TimeMachine drive to my new TimeCapsule drive. I haven't done any backups to the TC yet, and would like to be able to use the FireWire drive f

  • Multiple Safari Sessions

    My wife uses Safari and has her's set up the way she likes with important bookmarks on the task bar, homepage setup, etc. I want to open up Safari and have all my personal options at my fingertips as well. So I'm looking to have two different Safari