Dual Layer DVD encoding

I have a 90 minute movie that I wish to burn to DVD-9 (Dual Layer) to optimize quality. What settings would be best in compressor for the best image? Workflow is HDV>Prores422>Mpeg-2. What is the highest Bitrate that is compatible with the vast majority of set top players?

The maximum video bit rate allowed by the DVD specification is 9mbps. But in my experience, a bit rate higher than 8 can cause some players to skip and/or stutter. Personally, I never go higher than 7.2 and get excellent results.
Other things that can cause DVD stuttering:
PCM Audio - use AC3 audio only.
Low quality media like Memorex or store brands - use only known high quality brands like Taiyo Yuden or Verbatim.
Burning at too high of speed for the combination of media and burner you're using.
-DH

Similar Messages

  • IDVD refuses to burn lengthy video even though it's set to dual-layer DVD.

    *"Your project exceeds the maximum content duration. To burn this project, remove some content."*
    Project:
    *- total project duration: 164:10 minutes*
    *- total project capacity: 5.208 GB (max. available: 4.172 GB)*
    Menus:
    *- number of menus in project: 2 menus*
    *- total menu duration: 1:10 minutes*
    *- total menu capacity: 54.240 MB*
    Movies:
    *- total movies duration: 163:00 minutes*
    *- total movies capacity: 5.155 GB*
    This should fit quite snug on a dual-layer DVD, which I've gone to the preferences and changed to do so. It won't even let me make a disc image.

    What encoding mode / bit rate is it set at?
    I strongly suggest not exceeding 120 mins. (2 hours) max unless you opt to use a 3rd party app like Roxio Toast's Fit to DVD option.

  • Two hour sequence to dual-layer DVD?

    Hi,
    I'm confused.
    I have a two hour 16:9 sequence (actually 1 hour, 56 minute) that I want to put on a dual-layer DVD. I guess I didn't fully think it through when I sent it from FCP to Compressor and selected DVD 16:9 120 minute fastest encode, because it compressed it to 4.04 gigs rather than twice that size at a better quality. Now I'm looking for a setting that tells it my destination is a dual-layer DVD and I don't see it.
    Additionally, the m2v file that came from that process cut off the final minute or so of my sequence. Why in the world would that happen?
    Kenny

    These instructions assume you're using DSP for authoring. I don't know if iDVD has DL capability.
    The 'calculator' in Compressor assumes a single layer DVD. The key is to look at the summary, which is the far left tab in the Inspector. About 1/3 from the top, it will show the estimated file size. Adjust the bit rate selector until you get the file size approaching the capacity of the Dual Layer disk. You have other restrictions to consider as well. Totally data rate of video(s)audio(s)other data cannot exceed the maximum for the DVD spec (nominally 10mb/s).
    Once inside DSP, when you burn the disk, you'll be asked to select a marker to indicate where the burner will change from writing to the first layer to the second layer. This should occur at a convenient location in the video (a fade to black, eg.) near the end of the first layer capacity. If you don't already have a marker near that point, be sure to add one for the switch-over.
    Good luck
    allen

  • Dual Layer DVD...

    I want to burn my movie onto a dual layer DVD. There is a selection in DVDSP4 for dual layer, but how do I prep it for a lower compression/dual layer option in Compressor?

    Not necessarily - passes impact the encode time, the first pass is a test encode, the second one is the real thing (think of it has a rough draft). It has nothing to do with whether you're using single or dual layer media.
    It shouldn't change size in DVDSP - once the file is encoded that's it - it's going to stay that size no matter what. If its coming out at 4.7 GB you may be able to get away with single layer media.
    Message was edited by: wallybarthman

  • Dual layer DVD will not play after iDVD burning

    Hi All,
    I am having some trouble making a useable DVD. I have a video that I recorded and imported into iMovie (2h33m long). I exported it to iDVD, which told me that I needed to use a dual layer DVD to make it fit. Here's where I noticed the first problem: iDVD has one option for a dual layer disc, stating that it has 7.7GB storage space, and my discs have 8.5GB. I set it to use the standard setting for the DL disc any ways, turned the quality down a bit to make it fit, and burned the DVD. After burning two discs, I still do not have one that works. It comes up as "supported disc not available" on my Mac, and as a blank disc on any other machine I put it in. It will run on my coworker's brand new iMac, but that is the only one. Am I doing something wrong? The only mistake that I have corrected since I have tried all this is changing the aspect ratio back from 4:3 to 16:9 in iMovie (I am not sure how that happened, as the video was originally recorded in 16:9). I am re-exporting the file to my desktop now in the proper ratio, and changed the quality to HD. I am waiting for the file to encode as we speak. Any help would be greatly appreciated, as this work is for my local school board and is very time sensitive.
    I am running a 28" iMac, 2.66GHz Intel i5, 8GB RAM, 1TB hard drive on OSX 10.6.8.

    I set it to use the standard setting for the DL disc any ways, turned the quality down a bit to make it fit, and burned the DVD.
    That part I don't understand.
    iDVD encoding settings:
    http://support.apple.com/kb/HT1502?viewlocale=en_US
    Short version:
    Best Performance is for videos of up to 60 minutes
    Best Quality is for videos of up to 120 minutes
    Professional Quality is also for up to 120 minutes but even higher quality (and takes much longer)
    That was for single-layer DVDs. Double these numbers for dual-layer DVDs.
    Professional Quality: The Professional Quality option uses advanced two-pass technology to encode your video (The first pass determines which parts of the movie can be given greater compresson without quality loss and which parts can’t.  The second pass then encodes those different parts accordingly) , resulting in the best quality of video possible on your burned DVD. You can select this option regardless of your project’s duration (up to 2 hours of video for a single-layer disc and 4 hours for a double-layer disc). Because Professional Quality encoding is time-consuming (requiring about twice as much time to encode a project as the High Quality option, for example) choose it only if you are not concerned about the time taken.
    In both cases the maximum length includes titles, transitions and effects etc. Allow about 15 minutes for these.
    You can use the amount of video in your project as a rough determination of which method to choose. If your project has an hour or less of video (for a single-layer disc), choose Best Performance. If it has between 1 and 2 hours of video (for a single-layer disc), choose High Quality. If you want the best possible encoding quality for projects that are up to 2 hours (for a single-layer disc), choose Professional Quality. This option takes about twice as long as the High Quality option, so select it only if time is not an issue for you.
    Use the Capacity meter in the Project Info window (choose Project > Project Info) to determine how many minutes of video your project contains.
    NOTE: With the Best Performance setting, you can turn background encoding off by choosing Advanced > “Encode in Background.” The checkmark is removed to show it’s no longer selected. Turning off background encoding can help performance if your system seems sluggish.
    And whilst checking these settings in iDVD Preferences, make sure that the settings for NTSC/PAL and DV/DV Widescreen are also what you want.
    http://support.apple.com/kb/HT1502?viewlocale=en_US

  • Outputting a file for dual layer dvd

    Hi...is there a setting in Adobe media encoder that automatically caculates your timeline to fit a dual layer DVD?  The MPEG DVD output setting automatically shrinks it to 3 gigs, enough to fit a standard DVD.  I feel the quality of the file would be better if it was larger and burned to a dual layer. 
    Thanks

    If you're authoring in Encore, you set the Layer Breaks there.  You can let Encore find them for you automagically, or you can set your own, or render out your own separate timeline for each layer.  Read p.178 of the Encore Help PDF.

  • Dual layer dvd burning

    Hi,
    I need some help regarding dual layer dvd burning.
    I never burned a dual layer dvd before and am going to in the next few days for a big movie screening. So I better get this right.
    How do I set the layer break? do I just set it to be automatic or should I set a chapter in the track? if yes, then where do I suppose to put the chapter.
    Is there any advise regarding dual layer burning ? so that I have less possibilities of messing things up.
    Its a 115 mins movie. Im planning to encode it with 6.5 avg 8 max.
    Is it safe to put a lot of chapters in?
    I won't have dvd menu. I will just set it to play straight away.
    thanks.
    Jack

    I'm not an expert in the least but I have worked with duel layers and let me tell you than can be a real s.o.b. I'm not sure what the scoop is on them but they tend to glitch out while your burning. I made three and 1 worked perfect the other two not at all and for some reason the 1 that did work only played on about half of the DVD players they were played on. When I got it into a DVD player that worked the chapter markers were not a problem. I had four seperate segments that were linked up and played fine. We used this for a screening in front of about 400 people.
    Our feature was about the same length as yours so after the screening we decided to just take the quality down a little (which you can't even tell) and put it on a normal DVD R. We saved a ton in duplication.
    Setting the Duel Layer is pretty easy, it's all in the inspector under the disc/volume tab but make sure that in your outline window the main DVD at the top is highlighted. I don't think it matters if you have a chapter in the middle of the footage or anything like that. You can just link up one long stream if needed. Be sure to try out the DVD on the actual player you are going to use. Good luck.

  • Dual Layer DVD's compability with Settop DVD players

    Is there any problems with playing Dual Layer DVD's on a normal consumer DVD Video player?
    Is the DVD Video Player able to read the DVD-r DL or DVD+r DL disks at all?

    Hi Chris,
    All my previews go out through a bit setting DVD 5 downsized system. It's probably 3 years old now. I must admit until yesterday I had completely forgotten about this. As it's just part of the workflow. From having looked around last night my understanding is currently that some +R recorders now come preset to bit encode for DVD-ROM straight out of the box.
    I will also have to look into what Toast is currently outputting. You know the old adage if it ain't broke.....
    I have been very slack with respect to my DVD 9's. I simply use toast as I have normally post authored my build folders. But, those good results may be in part due to the fact that pretty much all my product goes to producers and DVD facilities. So it's either going to end up on a relatively young machines or PC's. None of it would end up in a home i would think.
    Good Luck.

  • Dual layer DVD exhibits blurred motion

    Have a project that is 2 hours and 35 minutes. Takes up 6.8 gigs. Project info shows yellow in the bars. I originally did a draft in iDVD 08 (using three discs) and all slow motion sequences or any clips with fairly quick motion are fine. To put the project on one disc, burned a dual layer in Studio Pro 4 and same clips have a blurred look to them re: motion.
    Am I trying to cram too much on one dual layer DVD? Using Verbatim 8.5 gig DVD's.
    thanks in advance for any advice

    Hi
    It seems you are encoding from inside DVDSP, then probably your encode settings are creating the low quality. Besides that, you must be getting AIFF audio encoding, what takes a lot of the free available space.
    My recommendation is to use Compressor to encode your UAdio to AC3 and take the standard High Quality 90 min preset for the video. With that video encoding preset you can fit 90 min in a single layer DVD and double in a dual layer one.
    Then import the M2V and AC3 file in DVDSP.
    Hope that helps !
      Alberto

  • Best compression setting 90min movie on Dual Layer DVD

    Okay, I admit, I am a total n00b at this...so sorry if you have to break things down into the most basic terms...
    I am trying to get the BEST quality I can for my adobe Encore project (for ease of calculation, 90min movie and added features).  I was previously getting "exceeds dvd capacity" error in Encore. 
    I have decided to recompress and see what I can do to make it all fit, but first I want to re-evaluate my whole process...
    the ultimate issue comes down to three things (i think)...
    1. CBR v VBR??  what is better and why?
    2. What Data Bit Rate to compress at and why?
    3. Single layer DVD vs Dual Layer DVD?  Which is better and why?
    to begin the discussion, I'll tell you what I "know" and what I think.
    It seems DVD players can only handle a max bit rate of 8mbps so I don't want to go over that and using a Dual layer disc I risk that it may not work on older players....also, the dual layer costs twice as much to duplicate (this sucks but money is not an issue at this point, quality is more important).  From what I have read, constant Bit Rate @ 8mbps will give me the Best possible image... 8 is the max and so to encode at 8 the entire time should be the best..  will i have any issues with this?  This is not an amateur home movie but rather an indie feature film so I want to get the best possible viewable product out to people.  I will have blu-ray questions to come later (thats what we are going to send to festivals).
    any help would be greatly appreciated
    thanks so much...
    chris

    Okay, thanks for everyone's thoughts.
    Question....
    I totally understand not wanting to waste space on a dvd IF there was extra room.... HOWEVER, a movie at 90min with menus, etc. BARELY fits on a dvd at a 6.8mbps VBR compression rate....
    therefore....why not just fork out the extra couple bucks and just compress the whole thing at 8.0mbps 2pass CBR, slap it on a dual layer and even though there will be parts of the movie that will be higher than necessary, and there will be leftover space on the dual layer dvd.... you will be guaranteed to have the highest quality right?  heavy motion areas and more static areas will all be encoded at 8 and thus, the best....
    am i wrong in thinking this?
    and after some extensive reading and research....Although is says a dvd player can handle 9.8mbps..... it doesnt' seem safe to encode that high because a lot of players can't handle it.... what is everyone else's thoughts?
    I found this:
    Data rate 
    DVD-Video discs have a raw bitrate of 11.08 Mbit/s, with a 1.0 Mbit/s overhead, leaving a payload bitrate of 10.08 Mbit/s. Of this, up to 3.36 Mbit/s can be used for subtitles and a maximum of 9.80 Mbit/s can be split amongst audio and video. In the case of multiple angles the data is stored interleaved, and so there's a bitrate penalty leading to a max bitrate of 8 Mbit/s per angle to compensate for additional seek time. This limit is not cumulative, so each additional angle can still have up to 8 Mbit/s of bitrate available.
    Professionally encoded videos average a bitrate of 4-5 Mbit/s with a maximum of 7–8 Mbit/s in high-action scenes. This is typically done to allow greater compatibility amongst players, and to help prevent buffer underruns in the case of dirty or scratched discs.

  • Creating Dual Layer DVDs

    I'm trying to encode a dual layer DVD. I'm rendering the project with iDVD and creating a disk image of the DVD on my hard drive. I'm then using Disk Utility to burn the image to a DL disk. The DVD plays fine about half-way through on my DVD player and then freezes. I'm guessing the DVD player is having trouble transitioning to the second layer indicating there is a problem w/ the way it was encoded. The DVD player is functioning fine, as it does not have problems with other dual layered disks.
    Is Disk Utility capable of burning a disk image formatted for dual layers onto a DVD? I don't know if iDVD is creating a bad dual layer disk image or if Disk Utility is incapable of encoding a dual layer disk image to a DVD.
    Could someone please comment on what the best way to get a dual layer disk image transferred to a dl DVD using iDVD would be?
    Thanks in advance.

    I agree with Len. You'll have much better luck with Roxio Toast. Len is also very successful at burning from a disc image via Roxio Toast at 4x or slower. And this is really the best approach in my opinion. However I do want to point out exactly what the iDVD Help Menu states with regards to using a disc image and dual layer media. Pay special attention to the final paragraph below:
    Creating a disc image of a project
    You can create a disc image of your project so you can burn additional DVDs of your project without going through the encoding process each time.
    Saving a disc image of your project creates a file that is formatted just like a finished DVD, except it’s not actually burned on a disc. All the media is compressed into the format used on a DVD, and you can play it on your computer by double-clicking the disc image icon and opening DVD Player.
    To create a disc image:
    Choose File > Save As Disc Image.
    Type a name for the disc image.
    Choose where you want to store the disc image.
    Click Save.
    You can use Disk Utility in Mac OS X to burn the disc image to a DVD when you are ready.
    Note: If you burn your project to a double-layer disc, you should burn directly from iDVD rather than from a disc image. A disc-burning utility will not set the layer break according to DVD specifications and may cause playback issues.
    Hope this helps
    SDMacuser

  • Need Help regarding Dual Layer DVD Writer

    Hi All,
    I want to burn a Dual Layer DVD on my Macbook but I am not sure if it the DVD Writer which I have in macbook will support or not. Below are the details of the drive
    HL-DT-ST DVDRW GSA-S10N:
    Firmware Revision: BP10
    Interconnect: ATAPI
    Burn Support: Yes (Apple Shipping Drive)
    Cache: 2048 KB
    Reads DVD: Yes
    CD-Write: -R, -RW
    DVD-Write: -R, -R DL, -RW, +R, +R DL, +RW
    Write Strategies: CD-TAO, CD-SAO, CD-Raw, DVD-DAO
    Media: Insert media and refresh to show available burn speeds
    Plz, if anyone can help me with this, I will really appreciate, Thanks in advance.

    Your computer will burn dual layer DVDs.
    (37544)

  • Keeps asking for Dual layer DVD

    I made a slideshow in iMovie and shared to iDVD8. The media windows shows the file as 2.7 gig. But when I go to burn it says to insert a Dual Layer DVD because the project to large.
    I dont have anything else in the project other then the menu which is 3 drop areas. Nothing to it.
    I tried sharing again from imovie and selected medium this time with a files size of 1.7gig and i still get the same thing.
    I do have quality set for PRO.

    good question. I used the Theme that has half the screen as a grey fade. When i added music to it i changed it to 25 secs of playback. I would assume then my menu is only 25sec. It only has 1 button to start the movie.
    At this point I have a DVD+R DL created that works fine my PC. After googling around I read about DL and changing the bitsetting before burning so that a TV DVD Player sees the disk as a DVD-ROM.
    Would I be able to copy this DVD+R DL with Toast 8 and change that setting to make it work?
    BTW, thank you for all the replies.
    Bill

  • DVD RW DW-U10A won't read burned Dual Layer DVD

    My friend created a dual layer dvd for me on his PC. I put it in my G5 and after about 15 seconds of the drive trying to read the dist it just gets spit out. It won't mount or anything.
    Why is this happening? I've never had problems reading discs created on a PC. Is my drive incompatible with DVD DL+R media?

    Hi,
    I've been having a similar issues since not long ago. I think it coincides with Apple,s last security update (although I can't swear the 2 are connected).
    I have a dual core 2GHz PowerMac G5 with a Pioneer DVD-R 110D Dual Layer.
    I'm burning Dual Layers medias with Toast 7 (DATA, DVD-VIDEOS ETC). They all mount fine after and I can read the files etc. However if I insert the discs a few day slater, about 50% of them won't mount and are rejected without any error message!
    Anyone else has this problem?

  • Sense Error Message when trying to burn Dual-Layer DVDs?

    Hey all,
    I am trying to burn a dual-layer DVD disc with the internal drive in my MacBook Pro.
    I am getting the same error message from Toast each time I try to burn a disc. I get no response from Disk Utility (it just says "waiting for the disc drive") and Finder doesn't recognize the dual-layer disc when I try to burn in Finder.
    I've heard that it may be a media issue, so I've tried with every single brand of DVDs that I can get my hands on. So far, I've tried Verbatim, Sony, and Memorex. I can't find any other brands of media, even at Best Buy?
    I've heard that it may be a security update that might have caused this issue. System Profiler says that my machine can burn both DVD+R DL and DVD-R DL.
    What is going on?!??

    Welcome to Apple Support Communities
    The two most common suggestions are (a) try other media, which you've done (and Verbatim normally work) and (b) run a DVD Lens Cleaner disc through it to see if some dirt or dust on the lens it causing the problem. If this doesn't fix it then it sounds like a hardware fault and best to let Apple check it out.

Maybe you are looking for