Dual Layer DVD Stock

Has anyone had any good / bad experiences with any brand of dual layer DVD stock? I'm getting ready to start a project and I have an external LaCie dual layer burner that I want to burn to. Thanks in advance!

I have also had miserable luck with Memorex DVD-R DL blanks. The only ones that verify at all are those that I burn at, 1x and two out of three of those are coasters. At $3 each that's really annoying.
I think I'd have gotten more enjoyment out of lighting cigars with the $60 I paid for the 20 discs rather than giving it to Staples for expensive coasters.
Taiyo Yuden, Fuji, and newer Verbatim seem to be the best mfg of DVD-R DL blanks. But their stuff is still pricey. Mitsui also makes great blanks, but I don't know if they are making DVD-R DLs yet.
Check out this website that rates optical media:
http://www.digitalfaq.com/media.dvdmedia.htm
I did find a vendor who would sell me Taiyo Yuden DVD-R DL blanks for $1 ea., but I needed to buy a minimum of 300.
Beware that if you are burning a DVD-Video disc via DVDSP to one of these beauties, DVDSP does not verify the burn afterward like Toast or the built-in OS X disc burner.
So you may not be aware of errors in your disc. Watch out for this if you are burning a disc to send off for mastering.

Similar Messages

  • Using Dual Layer DVD with iDVD

    I have a 2 hour movie that I have imported into iDVD. I put in a dual layer DVD-R, but iDVD insists that my two hour movie can fit on a single layer DVD-R. Yes, I'm sure it can crunch the heck out of it, but I want the quality to be high--THAT is why I BOUGHT a dual layer support drive!
    Is there any way I can tell iDVD to not crunch it down to 4.5 Gigs, but to just 9 Gigs?

    Hey, you used the word "experiment" twice in the same forum which gets you twenty points but you lose 10 points since it was for the same experiment.
    I get twenty (40-20) just for writing this response. Points are redeemable at the nearest refrigerator for hoppy beverages providing that you speak nicely to the member of the household that stocks said items, (or you can play back audio of yourself speaking compliments, but it must be recorded in 16 bit audio, as 12 bit audio will only buy you grief).

  • Burning Dual Layer DVD's

    Hi everyone,
    I have a refurbished MBP- 15.4" 2.53 GHz Dual Core 320 GB with 10.6.3 and Toast 10. As I just got the MBP and haven't burned anything with it yet, my question is, which DVD-/+R DL media is the best to use. On my G4 MDD, I typically have problems burning Sony, Maxell and (sometimes) Memorex media. Normally TDK and Philips work best on that unit.
    Any suggestions?
    Thanks in advance!

    Thans for the suggestion guys. I did buy the Verbatim DL DVD and they seem to work great. But I can't seem to get them to work with Toast 10:
    I attempted to burn a dual layer dvd (Verbatim DVD+R DL, 8X) on my (PowerPC) Mac G4, 10.4.11, Toast 9.0.7. The drive is a Pioneer DVR-109 with DL layer burn capabilities. I turned buffer under-run protection off and burned at 2.4X speed (on an 8X disc). The burn failed. I got the following error right off the bat:
    Sense Key Illegal Request
    Sense Code 0x26
    Invalid Field in Parameter List
    I attempted to burn another dual layer dvd on my (Intel) MacBook Pro 2.53 GHz dual duo-core, running 10.6.4 with the stock superdrive. Toast 10.0.3. Same settings (buffer under-run off, 2.4X speed, 8X disc). Same error.
    Both times I was burning as Disc Copy of a dmg file.
    When I attempted to burn the files on both my G4 and MacBookPro through the Finder/Disk Utility, both burns were successful.
    I don't want to have to save an image file out of Toast each time I go to burn a dual layer disc and then burn with the Finder/Disk Utilities. Is there any other really good media burner for Mac that I can use instead of Toast? I don't want one that just burns video as I want to be able to burn data disks as well (both Mac and PC format) and audio.
    Thanks in advance for any help!

  • Need Help regarding Dual Layer DVD Writer

    Hi All,
    I want to burn a Dual Layer DVD on my Macbook but I am not sure if it the DVD Writer which I have in macbook will support or not. Below are the details of the drive
    HL-DT-ST DVDRW GSA-S10N:
    Firmware Revision: BP10
    Interconnect: ATAPI
    Burn Support: Yes (Apple Shipping Drive)
    Cache: 2048 KB
    Reads DVD: Yes
    CD-Write: -R, -RW
    DVD-Write: -R, -R DL, -RW, +R, +R DL, +RW
    Write Strategies: CD-TAO, CD-SAO, CD-Raw, DVD-DAO
    Media: Insert media and refresh to show available burn speeds
    Plz, if anyone can help me with this, I will really appreciate, Thanks in advance.

    Your computer will burn dual layer DVDs.
    (37544)

  • Keeps asking for Dual layer DVD

    I made a slideshow in iMovie and shared to iDVD8. The media windows shows the file as 2.7 gig. But when I go to burn it says to insert a Dual Layer DVD because the project to large.
    I dont have anything else in the project other then the menu which is 3 drop areas. Nothing to it.
    I tried sharing again from imovie and selected medium this time with a files size of 1.7gig and i still get the same thing.
    I do have quality set for PRO.

    good question. I used the Theme that has half the screen as a grey fade. When i added music to it i changed it to 25 secs of playback. I would assume then my menu is only 25sec. It only has 1 button to start the movie.
    At this point I have a DVD+R DL created that works fine my PC. After googling around I read about DL and changing the bitsetting before burning so that a TV DVD Player sees the disk as a DVD-ROM.
    Would I be able to copy this DVD+R DL with Toast 8 and change that setting to make it work?
    BTW, thank you for all the replies.
    Bill

  • DVD RW DW-U10A won't read burned Dual Layer DVD

    My friend created a dual layer dvd for me on his PC. I put it in my G5 and after about 15 seconds of the drive trying to read the dist it just gets spit out. It won't mount or anything.
    Why is this happening? I've never had problems reading discs created on a PC. Is my drive incompatible with DVD DL+R media?

    Hi,
    I've been having a similar issues since not long ago. I think it coincides with Apple,s last security update (although I can't swear the 2 are connected).
    I have a dual core 2GHz PowerMac G5 with a Pioneer DVD-R 110D Dual Layer.
    I'm burning Dual Layers medias with Toast 7 (DATA, DVD-VIDEOS ETC). They all mount fine after and I can read the files etc. However if I insert the discs a few day slater, about 50% of them won't mount and are rejected without any error message!
    Anyone else has this problem?

  • Sense Error Message when trying to burn Dual-Layer DVDs?

    Hey all,
    I am trying to burn a dual-layer DVD disc with the internal drive in my MacBook Pro.
    I am getting the same error message from Toast each time I try to burn a disc. I get no response from Disk Utility (it just says "waiting for the disc drive") and Finder doesn't recognize the dual-layer disc when I try to burn in Finder.
    I've heard that it may be a media issue, so I've tried with every single brand of DVDs that I can get my hands on. So far, I've tried Verbatim, Sony, and Memorex. I can't find any other brands of media, even at Best Buy?
    I've heard that it may be a security update that might have caused this issue. System Profiler says that my machine can burn both DVD+R DL and DVD-R DL.
    What is going on?!??

    Welcome to Apple Support Communities
    The two most common suggestions are (a) try other media, which you've done (and Verbatim normally work) and (b) run a DVD Lens Cleaner disc through it to see if some dirt or dust on the lens it causing the problem. If this doesn't fix it then it sounds like a hardware fault and best to let Apple check it out.

  • IDVD refuses to burn lengthy video even though it's set to dual-layer DVD.

    *"Your project exceeds the maximum content duration. To burn this project, remove some content."*
    Project:
    *- total project duration: 164:10 minutes*
    *- total project capacity: 5.208 GB (max. available: 4.172 GB)*
    Menus:
    *- number of menus in project: 2 menus*
    *- total menu duration: 1:10 minutes*
    *- total menu capacity: 54.240 MB*
    Movies:
    *- total movies duration: 163:00 minutes*
    *- total movies capacity: 5.155 GB*
    This should fit quite snug on a dual-layer DVD, which I've gone to the preferences and changed to do so. It won't even let me make a disc image.

    What encoding mode / bit rate is it set at?
    I strongly suggest not exceeding 120 mins. (2 hours) max unless you opt to use a 3rd party app like Roxio Toast's Fit to DVD option.

  • Two hour sequence to dual-layer DVD?

    Hi,
    I'm confused.
    I have a two hour 16:9 sequence (actually 1 hour, 56 minute) that I want to put on a dual-layer DVD. I guess I didn't fully think it through when I sent it from FCP to Compressor and selected DVD 16:9 120 minute fastest encode, because it compressed it to 4.04 gigs rather than twice that size at a better quality. Now I'm looking for a setting that tells it my destination is a dual-layer DVD and I don't see it.
    Additionally, the m2v file that came from that process cut off the final minute or so of my sequence. Why in the world would that happen?
    Kenny

    These instructions assume you're using DSP for authoring. I don't know if iDVD has DL capability.
    The 'calculator' in Compressor assumes a single layer DVD. The key is to look at the summary, which is the far left tab in the Inspector. About 1/3 from the top, it will show the estimated file size. Adjust the bit rate selector until you get the file size approaching the capacity of the Dual Layer disk. You have other restrictions to consider as well. Totally data rate of video(s)audio(s)other data cannot exceed the maximum for the DVD spec (nominally 10mb/s).
    Once inside DSP, when you burn the disk, you'll be asked to select a marker to indicate where the burner will change from writing to the first layer to the second layer. This should occur at a convenient location in the video (a fade to black, eg.) near the end of the first layer capacity. If you don't already have a marker near that point, be sure to add one for the switch-over.
    Good luck
    allen

  • System stuck formatting dual-layer DVD

    I'm trying to format a dual-layer DVD but my system gets stuck in the very beginning "Writing image..." part of the formatting process (I waited at least an hour). If I click cancel, I get the warning:
    "Stopping now may produce an unreliable disc...operation is not complete".
    When I choose to Stop formatting, I get the pinwheel, force quit does not work properly and I have to Restart computer.
    I've got DVDSP set to:
    • Dual layer
    • OTP
    • a DL breakpoint that DVDSP OK'd (in black after building the disc) in the Break Point pull down options
    • Seamless not checked
    • and Lossless Linking not checked
    DVDSP says current disc volume is 6.7GB, 5.9 of which is my movie and the rest are menu assets.
    I'm burning to an external DiscMakers Reflex duplicator using a MAM-A DL DVD+R disc. DVDSP has been able to successfully recognize burner.
    Any help greatly appreciated.

    I experienced exactly the same problem recently twice in succession when I tried to burn to Verbatim DVD+R DL disks. After running two Verbatim disks in DVDSP 4, I gave up on DVDSP 4 for burning DVD + R DL disks and went to Toast 8 and burned and verified the disks with no problems. While some people are apparently able to burn DL disks successfully in DVDSP 4, I have not been able to. The fact that Toast 8 burned to the same VErbatim DVD+R DL disks that had failed in DVDSP 4 seems to me to point clearly to a problem with burning DL disks in DVDSP 4.
    Tom

  • How can I get a dual layer DVD+R to burn properly?

    I can not get a dual layer DVD+R to burn properly. The disk pops out before it's finished, usually at the end of the multiplexing stage.  iDVD seems to think the disk is still burning for about 20 more minutes although the box says "done".  I tried it with an external DVD burner with the same result.  I'm running the latest iDVD version available on a MacBook Pro running Lion.  Any ideas out there?

    Hi
    Free space on Start-Up (Mac OS) Hard Disk - How much ?
    • for SD-Video and SL-DVD - I never go under 25Gb
    • for DL-DVD I would guess that 50Gb free is safe
    • if HD-material is used (needs space to be downscaled to SD-Vide0 as this is DVD standard) - 4-5 times more
    Yours Bengt W

  • Dual Layer DVD...

    I want to burn my movie onto a dual layer DVD. There is a selection in DVDSP4 for dual layer, but how do I prep it for a lower compression/dual layer option in Compressor?

    Not necessarily - passes impact the encode time, the first pass is a test encode, the second one is the real thing (think of it has a rough draft). It has nothing to do with whether you're using single or dual layer media.
    It shouldn't change size in DVDSP - once the file is encoded that's it - it's going to stay that size no matter what. If its coming out at 4.7 GB you may be able to get away with single layer media.
    Message was edited by: wallybarthman

  • Compressing 7.5 Hour video for Dual Layer DVD

    I've got to compress 7.5 hours of footage into an MPEG2 fittable on a Dual Layer DVD. The client knows that the quality will be inferior. Anyone have any suggestions as to settings before I start? I'm guessing to set the bitrate to 2.3 or so. How about the maximum? Thanks!

    I used Compressor and set everything on the MPEG 2 settings to the lowest I could, like 2.1-5.0 and compressed the **** out of it. It looks pretty decent for that much compression. It only fit because I chopped off the credits sequence from the 15 different sections, compressed that seperately, then had them link to it so that it was actually about seven hours of footage. There's a little pixelation when you go into certain motion areas, but the client's happy. I only recommend doing this if there are no other options.
    AK

  • Media write error for dual layer DVD burn

    I am having a problem burning a dmg to a dual layer DVD using the internal DVD writer. I have tried both Disk Utility and SimplyBurns.
    Both program s go through the preparation for the file, and when it attempts to burn the disk I get a 'media write error'. I am using Memorex DVD +R DL disks. I have successfully burned both CDs and regular DVDs with the drive.
    Does anyone have a suggestion on how I can fix this?
    Thanks

    I am using Memorex DVD +R DL disks.
    Try Verbatim DVD+R DL discs.

  • Project for dual layer DVD

    Hi there,
    I have a project which contains several individual sequences that have been compressed separately and which constitutes several parts of my future DVD.
    The total size is such that I need to burn a dual layer DVD.
    How do I determine where to include the marker indicating to switch layer ?
    I have done it before with a long project containing only one sequence, but this time the sequences are independent....
    Would DVDSP include automatically a "change layer" marker if I burn as is ?
    Thanks in advance
    Ivan

    I'd recommmend looking up "About Choosing a Dual-Layer Break Point" in the DVD Studio Pro user's manual or Help File.
    -DH

Maybe you are looking for