Dual LED Flash - any good in a dark environment?

I currently own a phone with a xenon flash which gives me really quite usable night-time (or nightclub rather!) shots, compared to my old LED flash phone that was pretty much useless in anything other than daylight or very bright internal lighting.
A couple of the Nokia phones I am looking at as an upgrade to my current phone have Dual-LED flashes - how do these compare to Xenon flashes? I guess they aren't as good, but do they at least give tolerable shots in low light conditions?

They still do not compare to the Xenon flash. Nokia should really be putting these on their high end phones as standard.
The best way to get a quick response is to use the boards. Please do not be offended if I don't answer emails immediately.

Similar Messages

I have problem with My dual LED flash On My iPhone 5s. The Amber LED doesnt work at All. I dont know Since when It happened,.. Does anyone Know how to solve This?

When i bought This iPhone 5s one Month ago, all The functionalities of This iPhone 5s worked normally. And somehow, i have just noticed that My amber_led doesnt work when i use My Camera. I am sure that i have The flash turned On at The screen. And Also The white LED working properly. So., does anyone Know how to Solve The issue? Thank you

I believe there are 1500 different mixes of brightness for the two LEDs to produce an accurate color tone on the "flashed" subject. So possibly there are situations where the bottom LED would appear brighter than the top one, especially in very cool lighting conditions...
also there are software algorithms to control how bright each is..reesetting the phones settings should fix the problem if notthen, its a hardware related issue bring to apple its under warranty

Problem with Dual LED - N79

I have Nokia N79 for the past 10 months and today I realized that its dual LED flash is not working. It was fine till atleast last week. I tried a hard reset but its still not working. Please help me out with this problem

Hi ashwani26596,
Let's start by using the HP Support Assistant to check for any updates and drivers to see if that resolves the issue. If that doesn't work then go your Control Panel and then Programs and Features and uninstall the Catalyst Control Center. Then try installing both the Intel High-Definition Audio Driver and the AMD High-Definition Audio Driver.
Thank you,
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

My z10 led flashing red when charging and even at battery full it blinks red. no green at any note..

My z10 led flashing red when charging and even at battery full it blinks red. no green at any notification. But at below 10% charging level it blinks with a combination of red and green. Please send me any settings to be changed if.. at full charged no green light is blinking.. how many colours does z10 led have..and when it works and how to make those settings..or was my led not working fine? I am worried so much..plz help me

Your LED is fine, on the Z10 there is not "network signal available" green LED, as you're accustomed to from the legacy devices. At reaching 10%, the LED will blink orange.
Red for message or applicaiton notifications.
if you want to edit and create specific LED color combination, see the third party apps such as BeBuzz or Hub++
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Can anyone recommend any good books on leaning actionscript for flash?

Can anyone recommend any good books on leaning actionscript
for flash?
Intermediate level
I have been using flash for about 2 years more as a hobby
than anything else, some websites etc but now I realise I am going
to need to learn more actionscripting to do what I want, I have
come to terms with the simple stuff like goto – basic
variables – load mov – enough to programme up website
navigation.
I ideally want to learn more about the dynamic side of flash,
mostly for designing user interfaces and websites etc
I’m after a book that doesn’t get too heavy too
fast yet I’m a little past the more basic functions
Any thoughts?
Cheers

You appear to be stuck on iOS 4.2.1. That means up really have a 2G iPod. A real 3G can go to 5.1.1
.To find compatible apps more app for 4.2.1 see:
Old Apps
VintApps 3.1.3 for iPhone, iPod touch, and iPad on the iTunes App Store
apps for ios 4.2.1: Apple Support Communities
Finding iOS 4.2.1 Apps Compatible with Older Devices - Apple Club
HT4972 Touch Game 4.2.1 Apps: Apple Support Communities
apps for 4.2.1 (also works for 3.1.3)
Tip - Finding 4.2.1 apps that work on an...: Apple Support Communities
4.2.1 iPod 2nd generation unable to use any...: Apple Support Communities

Power LED flashes, firmware updates good, and can still access the router

I have a wrt54G first version as there is no version number. About two months ago, the power led started dropping out and with a reset worked for a day or so, then, it became worse, every hour, and now only a couple of minutes. according to the help side of this site, the router will not be accessible, but it is. I upgraded to the 4.7.1.1 firmware, the problem continues, un plug and start it up. Any ideas? Could it be the 12 volt power supply going bad or over shooting the power?

yes, that is the level, verified at the router. the help side of this site says that if the led flashes like this that it would be corrupt an un accessible, but a restart of the router stops it, and it is accessible, moreover, the upgrade fails since that is the level at the router. just that it is happening about every 15 minutes (8/3) - could it be that comcast is sending packets of ??? to blow out routers? Thee state they don't like people using routers - that you are not supposed to use more than one computer with their broad band connection. Yes - serious, the e have said this twice in the last 6 months. Don't know what it could be, Saturday - Sunday it has not dropped out at all

Recommend any good flash books...

Hi,
I want to learn how to connect flash CS3 to databases/dynamic
information etc....Can anyone recommend any good books. I just
bought Flash and PHP Bible but don't think much of it (it keeps
referring to a companion website that doesn't exist - the book only
came out this month). I want to learn how to connect databases with
flash, get dynamic content and things like that. Have any of you
guys used such a book that you thought was great?
Cheers...
Ben.

There are a lot of good online tutorials and such. If you
really want to do
it right, learn to use AMFPHP, a remoting gateway for PHP.
It'll make your
life much easier if you do any fair amount of database work
with Flash. I
still use LoadVars for simple forms and such, but for
anything bigger I use
AMFPHP / remoting.
Dave -
www.offroadfire.com
Head Developer
http://www.blurredistinction.com
Adobe Community Expert
http://www.adobe.com/communities/experts/

Phone is totally unresponsive. But has power (green led flashing). Was OK this morning. Any ideas?

Phone is totally unresponsive. But has power (green led flashing). Was OK this morning. Any ideas?

Will47,
Help has arrived! Does the device have any physical/liquid damage? Was the device in use or being charged when this happened?
EfrainM_VZW
Follow us on Twitter @VZWSupport

Three beeps then led flashes and fan is on

Hi. I haven't used my mac in a while and tried turning it on...it beeped three times then the led flashes three times and pauses, and the fan goes on full blast. I found out in my quest for answers that the 3 flashes could mean bad RAM. I have the factory installed RAM...I had some problem with my computer before and an apple tech put in a new logic board. Could this be the problem? I'd like to fix it myself since the tech is a hike away. Any thoughts? Thanks for the help.
PowerMac G5 2ghz Mac OS X (10.4.8)

Hi. Well -
Not sure whether you need the FW card for your recording session - but if you remove the FW card, and get the G5 up and stable first - then put back what you need and try it.
I would try to boot from the most recent system disc you have - presumably it came with 10.4 if you have a "Late 2005" dual-core 2GHz G5 with PCI-Express
http://support.apple.com/specs/powermac/PowerMac_G5_Late2005.html
- and Verify, or Repair if necessary, the startup disc
http://docs.info.apple.com/article.html?path=DiskUtility/10.5/en/duh1018.html
in case directory corruption has occurred during the various shutdowns and restarts.
If boot problems still persist, it may be worth re-seating the video card, also.
There are threads in the Forum mentioning that FW card
http://discussions.apple.com/search.jspa?objID=c108&search=Go&q=siig+NN-E20012-S 2
There is some discussion there of the power requirements of the connected firewire device - and of the possible need for a separate power connection to the card. It's also possible that the FW card needed re-seating, after the G5 not being used for a while.
It may also help to disconnect anything firewire - iSight, drives, etc. - not needed at this pressing moment...
Have presumed that you don't need Airport for tonight - but if it appears to causing problems with the basic startup, it can be disconnected; although this is more complicated on a dual-core, and to be avoided, if possible.
Anyway - trust some of this helps. Good Luck.

LED FLASH ISSUE !

Hello guys,im using an i5, my problem is about the led flash of iphone.LED flash is turning off itself when i tried to use it from the control panel.And my iphone is taking dark pictures in full of lightning room,when the flash is on.im not using a back plastic protector.is it a hardware bases or software bases problem? Thanks for ur help,sorry for bad English.

Hey there,
It sounds like the camera and LED are nto working as expected on your iPhone. I would use these troubleshooting steps to help isolate the issue from the following article:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/ts2802
Camera isn't functioning or has undesired image quality
Ensure the camera lens is clean and free from any obstructions. Use a microfiber polishing cloth to clean the lens.
Cases can interfere with the camera and the flash. Try gently cleaning the lens with a clean dry cloth or removing the case if you see image or color-quality issues with photos.
Try turning iPhone off and then back on.
Tap to focus the camera on the subject. The image may pulse or briefly go in and out of focus as it adjusts.
Try to remain steady while focusing:
Still images: Remain steady while taking the picture. If you move too far in any direction, the camera automatically refocuses to the center.
Note: If you take a picture with iPhone turned sideways, it is automatically saved in landscape orientation.
Video: Adjust focus before you begin recording. You can also tap to readjust focus while recording. Exiting the Camera application while recording will stop recording and will save the video to the Camera Roll.
Note: Video-recording features are not available on original iPhone or iPhone 3G.
If your iPhone has a front and rear camera, try switching between them to verify if the issue persists on both.
My issue is still not resolved. What do I do next?
Contact Apple Support
Thank you for using Apple Support Communities.
Regards,
Sterling

Is the i phone any good for those with essential tremour

is the i phone any good for those with essential tremour

Hi auchenshugglegranny,
Welcome to the Support Communities!
The iPhone has a number of accessibility features that may be helpful to you, including Siri, which will accept voice commands. The article below will provide an overview for you.
Apple - Accessibility
http://www.apple.com/accessibility/
Below is a list of features included in the iPhone User Guide:
Accessibility features - iPhone
http://help.apple.com/iphone/7/#/iph3e2e4367
VoiceOver
Support for braille displays
Siri
Zoom
Invert Colors
Speak Selection
Speak Auto-text
Large, bold, and high-contrast text
Reduce onscreen motion
On/off switch labels
Hearing aids
Subtitles and closed captions
LED Flash for Alerts
Mono audio and balance
Call audio routing
Assignable ringtones and vibrations
Phone noise cancellation
Guided Access
Switch Control
AssistiveTouch
Widescreen keyboards
Turn on accessibility features. Go to Settings > General > Accessibility, or use the Accessibility Shortcut. See Accessibility Shortcut.
Use iTunes to configure accessibility. You can choose some accessibility options in iTunes on your computer. Connect iPhone to your computer and select iPhone in the iTunes device list. Click Summary, then click Configure Accessibility at the bottom of the Summary screen.
Hope this information helps ...
Happy Holidays!
Judy

Blackberry 9900 bricked with red LED flashing

My cell phone Blackberry 9900 was bricked last night. No special usage or status before. Now it can't be turned on any more, just the LED flashing. I have tried many ways to re-turn it on, not work. It even can't connect to computer. the computer is able to find it just when the red LED is lighting!
What happened on my phone? What can I do next? I must turn it on!

Hi and Welcome to the Community!
Please try this sequence...note that, throughout the entire 4h15m process, your BB must remain directly connected to a known-good wall charger (not PC USB, not a cradle):
With the battery inside, connect your BB to the wall charger
Leave it alone for 2 hours, no matter what the LED or the display does
Remove the battery
Wait 15 minutes
Insert the battery
Wait another 2 hours, no matter what the LED or the display does
This has been known to "kick start" some BBs.
It is also possible that your battery or BB has experienced a problem...to test, this sequence is needed:
Obtain an known good and already fully charged additional battery...use it in your BB and see what happens
Obtain access to a known good and identical BB...use your battery in it and see what happens
The results of this will indicate if it's your BB or your battery that has the problem. Note carefully please that "new" and "know good" are not necessarily the same things. While rare, a "new" battery certainly could be defective. Rather, the simplest (and least costly, btw) method to conduct this test is to find someone with an identical BB who has no issues...trade batteries and see what happens.
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

LED flashes 3 times

Hi
I have just tried to install 2 x 1GB chips into my G5 that already has 2 x 256mb and 2 x 1GB and the led on the front is flashing 3 times. I believe this means Incompatible memory installed.
So I then removed the new Ram and left the old Ram in the same place as before. Same thing happens, 3 flashes. I have been using the old Ram for 3+ years.
I have tried removing everything and just replacing the original 2 x 256mb and still 3 x flashes.
any ideas.
Peter

The act of heating the logic board at the point where these RAM sockets are
soldered on, and have that work, means there are micro-fractures or a faulty
solder joint at the junction - - or worse - - a component nearby has failed.
Since heat expands and the sections needing a proper connection would be
forced together tighter at the higher temperature, that situation could be an
easier fix than some others involving a logic board's complex circuits & parts.
Had you noticed anything odd prior to this apparent failure, such as slower
applications, or other sluggishness? If this issue had started going out be-
fore your AppleCare coverage expired, and you were unaware of the cause,
you could've had some recourse through AppleCare in this matter... About
all a person could do, is pay for the tech support call, and have your notes
ready; and ask what - if any - options you have, since the cost of this at a
retail repair rate, breaks the bank; when a repair costs so much you can't
continue to do your work, you could be bankrupt. You don't need a computer
to go broke; anyone can do that and be essentially computer illiterate!
Good luck & happy computing!

LED flashing light and email notifications!

i just got the curve 9300 and before had the curve 8520 and the flashing LED is so dim i can barely see it on my new one!
i have the phone on silent at work and use the LED to tell when i have a notification and i cant even see it in daylight hardly.
is there any way to make the red light flash up brighter like on the older model?
my sister has the new bold and hers is fine and bright.
Ive got the free bebuzz app and even when i select my fave contact as BRIGHT pink it is still really dim light.
Also i have my hotmail account set up on my bb.
When i get a new email the notification icon appears at the top but i cant view the email in my hotmail box only if i go into the "messages" icon. this isnt how it was before either!
HELP?

misscandypop wrote:
so do they not all have a dimmer LED than other models then?
I do not have a 9300 device on hand. I have used one and tested one, and played with. The LED flashing was fine, with nothing less bright about it that I would have noticed or made me remember "oh this is dim".
misscandypop wrote:
you think its a fault on mine?
I don't know that, hence my suggestion to drop by where you purchased it and check another 9300 LED for comparison. There could certainly be some "personal preference" on this that you think it's not bright enough to you, but another 9300 might be brighter. There could some fault of your device. Do I think it's a fault on yours... I don't know. I haven't seen yours.
I'd also suggest that you UNinstall BeBuzz for now, completely uninstall, reboot your 9300 and test the LED from the native opertaing system settings.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Is 24" iMac really any good?

I know this is a vague question but hang with me.
I am about to buy a 24" iMac and decided to look on these forums first to check if there are any problems with them.
I have now read all sorts of horror stories regarding the screen (too bright/dead pixels/dark corners/etc...) Various problems with humming and misc noises coming from inside the Mac, and issues with audio quality output.
One of the main reasons for going for a new machine is Boot Camp. Now having read the Boot Camp forum it seems the 24 incher just won't work at all with the latest beta of Boot Camp.
Can I start a straw poll of owners with new 24" iMacs - are they any good? Are you happy with them? Is it the fact that we only heaar about the duff ones on these forums, or is it that a large percentage are inferior/faulty/unsatisfactory.
Your thoughts/recommendations/experiences would be welcomed.
Thanks

I was going to post a new topic with this but I will post it here instead.
I am on my second iMac in as many weeks, but this one is two hours old and it I am yet to find a fault with it.
My first iMac had a single green stuck pixel, I called apple and they replaced it and where very good.
I collected my new one about 3 hours ago from TNT and got it home. Took it out the box and notice the packaging was damaged and thought Oh god here we go...
Turnt it on and spent 5 minutes looking at every single pixel on the display then I saw a single black dot.. luckily it was just a bit of dust!
I booted it up, had trouble with setting up the keyboard, it just didnt work first time, But I got over that. Mouse was a doddle to set up! (both wireless)
Now it is just working perfectly! Wireless is working great, iSight and Photobooth are fantastic! (I love the effects!!) The speakers are VERY good for a device that is so thin!
I am yet to try a movie or DVD at the moment I am just playing with it, getting it configured and what not.
There are dark corners on the display, but its really nothing to worry about. You dont really notice them, you just need to look really hard to find them.
There is also a very important factor which many over look. It smells nice!!
They keyboard is great, quiet and responsive, its white and I am a little scared of making it dirty!! it just looks so good. The mouse is a little heavy but I am just used to using a decent gaming mouse from my pc which is very light.
Overall when you get a proper working one it works great, peforms fast and does exactly what it says on the tin.
I dont get the so called brightness buzz, if I do, the noise from my PC is overpowering it and stopping me from hearing it so its really nothing to worry about.
I was worried about the problems described here when I ordered but the thing is, this is a user support forum, IE the only people who are going to post are the ones with problems. If you get your mac and your not happy then call Apple as soon as possible and they will do every effort to ensure they get it fixed!
Adam "happy mac man" C
OOOO I need to update my mac info now below : D woooooohooooo

Dual LED Flash - any good in a dark environment?

Similar Messages

Maybe you are looking for