Dual Monitor Issue: 2nd Display too large...can't adjust...web pages provide no scroll bars

I have two (2) HP S2031 LCD flat screen monitors. They functioned perfectly with my old 32-bit machine (now gone). I have just purchased a new 64-bit Windows 7 machine. There are no error messages, but if I open a web page on the right (2nd) monitor, it does not display correctly. It's as if it is a little too large. I've tried adjusting the image using the Nividia software and using the monitor adjustments without improvement. It is difficult getting out of that window because no scroll bars (vertical or horizontal) present themselves. I am connecting through an iogear MiniView KVM switch to DVi-D sockets (with the four pins).
Is it a 64-bit driver issue? I think not, because display #1 looks fine. Could it be an iogear KVM firmware issue?
I dug out the HP driver disks that came with my monitors and installed them. After I did that, I realized these were a 32-bit installation. Now the monitor resolution won't go back to the higher, recommended level. I don't see the software installation on the "add/remove programs" listing. I'd like to change that.
BUT THE REAL ISSUE is that I need BOTH monitors to be able to display proper aspect independently. Remember, I've been through both the Nividia adjustments menu and the built-in monitor adjustments menu and found nothing that worked so far.
Please help if you can. This is for my trading business and I need it desperately.

When requesting assistance, please provide the brand and model name and/or product number of the computer in question. Without this information, it may be difficult or impossible to resolve your issue.
Have you swapped the two monitors to see if the problem follows the monitor or remains at the same location??? Try that first... if the problem follows the monitor, perform a hard reset by unpluging the monitor from power then holding the power button for 30 seconds. If the problem stays in the same location, you know both monitors are good and I would suspect the KVM isn't passing the "EDID" data to the computer. Removing the KVM should will tell you if this is the case.
Please post back with your troubleshooting results.
Please send KUDOs
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

Similar Messages

How can I browse my page without a scroll bar?

Hi, I 'd like to have my site in specific size(1360x768pix) without a scroll bar, since I 'm making it for a wide screen PC for a special occasion.
I unchecked "sticky footer" , set 0 for both "Mergin" and "padding" of the "Page property".
Although I set page size and property to make it fit on the screen, It shows scroll bars on the right and bottm of the browser.
Is there any way to get rid of a scroll bar??
It would be great if you could give me some ideas.
Thanx!

Thanks for the tip, guys!!
I insert the
<style type="text/css">
overflow:hidden;
</style>
code in the<head>Sec. in the Matadata panel of the PageProperties. But I can't get rid of the scroll bar yet.
Do I do that procedure for the every pages?? There's no Metadata panel in the Master page's Page property but other's. Thanx!

Suddenly I can not select anything within the top inch or so of any web page. The scroll bar arrow doesn't work at the top. I don't know what to do. I tried updating my browser but the problem still exists.

Everything worked fine on Tues. I shut down my system and then on Wed. morning, the problem appeared. Anything within the top inch or so of a webpage is unavailable to select. It is like there is an inch of the page that is dead. It is that way on every website that I visit with Firefox. It does not happen if I use internet explorer, which I do not like and do not want to have to go back to using. Please help!!! My sister in law has the same problem with firefox.

Hi,
Please [https://support.mozilla.org/en-US/questions/911441 see this.] You may also want to check if this happens in [https://support.mozilla.com/en-US/kb/Safe%20Mode Safe Mode.]

The display on my monitor is too large (can't fit the whole screen on my monitor) even though I have the correct resolution. Suggestions?

The display on my monitor is too large (can't fit the whole screen on my monitor) even though the resolution is correct. Suggestions?

Sounds like it may just be enlarged. Have you tried holding down the <ctrl> key and moving the mouse up and down, or scrolling your finger up and down if you have a magic pad.

Attached images display too large

when using mail in os 10.4, if someone sends me a message with pictures attached, they are at a size that you can see the whole picture when you scroll down in the message. if i forward that email to someone, the pictures display too large and you cannot see the whole image in the message. is there a setting for this somewhere?
thanks

BDAqua wrote:
Ah thanks, maybe I was experimenting with too small of pics!?
Hmm, interesting...
Mail will remebember the size and will automatically use it the next time you attach an image if you forget to manually change it back.
And if the last setting was small, the menu may be there, but will have no effect since you cannot Scale up!
Yes, it works only for downsizing.
Also, it seems that if the pic is in quoted nesting the size setting has no effect!?
On Mac OS X 10.5 and later it works regardless of quotation. If it does not on Mac OS X Tiger, it must be a bug that was fixed later.

Sync error: Uploading records failed: "client issue: request body too large"

1328917629619 Sync.Engine.AdblockPlus DEBUG Uploading records failed: "client issue: request body too large"
This happens from 2 Win 7 computer and 1 Win XP computer sync'd. Without the Add Block Plus being sync'd everything works.

Hi!
That's a problem with the Add Block Plus sync engine. It seems that they have issues on their servers.
Try to ask the same question in their forum: https://adblockplus.org/forum/
Good luck!

F5061 Balance in local currency EUR is too large for automatic adjustment

My Company code currency is EUR. The customer has made a downpayment in USD (say 100) and i am now to clear the same against invoice of same amount in USD (100 $) but its is resulting into minor differences in Local currency. I am getting the following error
Balance in local currency EUR is too large for automatic adjustment
Message no. F5061
Diagnosis
For postings in foreign currency, it is possible that the balance in foreign currency is zero, but not in local currency. Providing the balance in local currency does not amount to more currency units than the document has line items, the system adjusts the amounts automatically. If an automatic adjustment is not possible, the amounts must be adjusted manually in local currency.
System Response
The document is not posted in local currency without adjusting the amounts.
Procedure
Adjust the amounts in local currency.
How can i have the system automatically fetch the Gl accounts to post the exchange rate differeces.
I have maintained the settings in FBKP- Exchange rate differenes
Thanks & Regards
Pooja

Hi,
I have the same problem; my company code is defined in HUF and I am trying to post a vendor invoice in Euros.
I have a 10% maintained there and still receiving the error, either for differences of just one HUF. The strangest thing is that differences are automatically adjusted (also for discrepancies over the 10%) when posting through FB60 but not when using FB01.
Any idea?
Thanks in advance for your input.
Best regards.

How can I display XSLT transformer errors on a web page ?

Hi,
I have some JSP pages that access DB, create an XML based on DB data and then transform it into HTML through an XSLT stylesheet. Developing the XSL code it's easy to make mistakes and generate errors on trasformation, but what I receive on the web page is only a "Could not compile stylesheet" TransformerConfigurationException, while the real cause of the error is displayed only on tomcat logs. This is the code for transformation:
static public void applyXSLT(Document docXML, InputStream isXSL, PrintWriter pw) throws TransformerException, Exception {
        // instantiate the TransformerFactory.
        TransformerFactory tFactory = TransformerFactory.newInstance();
        // creates an error listener
        XslErrorListener xel = new XslErrorListener();
        // sets the error listener for the factory
        tFactory.setErrorListener(xel);
        // generate the transformer
        Transformer transformer = tFactory.newTransformer(new SAXSource(new InputSource(isXSL)));
        // transforms the XML Source and sends the output to the HTTP response
        transformer.transform(new DOMSource(docXML), new StreamResult(pw));
}If an exception is thrown during the execution of this code, its error message is displayed on the web page.
This is the listener class:
public class XslErrorListener implements ErrorListener {
    public XslErrorListener() {
    public void warning(TransformerException ex) {
        // logs on error log
        System.err.println("\n\nWarning on XEL: " + ex.getMessage());
    public void error(TransformerException ex) throws TransformerException {
        // logs on error log
        System.err.println("\n\nError on XEL: " + ex.getMessage());
        // and throws it
        throw ex;
    public void fatalError(TransformerException ex) throws TransformerException {
        // logs on error log
        System.err.println("\n\nFatal Error on XEL: " + ex.getMessage());
        // and throws it
        throw ex;
}When I have an error in the XSL stylesheet (for examples a missing closing tag), I can find on tomcat logs the real cause of the error:
[Fatal Error] :59:10: The element type "table" must be terminated by the matching end-tag "</table>".
Error on XEL: The element type "table" must be terminated by the matching end-tag "</table>".but on my web page is reported just the TransformerConfigurationException message that is:
"Could not compile stylesheet".
How can I display the real cause of the error directly on the web page?
Thanks,
Andrea

This code is part of a bigger project that let developers edit XSL stylesheets through a file upload on the system and we can't impose the use of any tool for checking the xsl. So, I need to display the transformer error on the web page.I see. This code is part of an editorial/developmental tool for developers to create and edit XSL stylesheets.
As part of the editorial process, XSL errors during editing can be considered a normal condition. In other words, it is normal to expect that the developers will generate XSL errors as they are developing stylesheets.
In this light, handling the XSL transformation errors is a business requirement that you need to handle. Using the Java Exceptions mechanisms, e.g. try / catch are inappropriate to handle business requirements, in my opinion.
I suggest that you look at how you handle the occurence of XSL errors differently than what you currently have. You need to:
(1) capture the Transformation exception on the server;
(2) extract the message from the exception and put it into a message that can be easily understood by the user;
The current error message that you have going to the web browser is not useful.
And you should not have the Transformation exception sent to the web browser either.
What you are attempting to do with the exception is not appropriate.
Handle the Transformation exception on the Business tier and use it to create a useful message that is then sent to the Presentation tier. In other words, do not send Java exceptions to web browser.
/>

Can't open web page because too many redirects

Get the message Can"t open web page because too many redirects

Try clearing Safari and restart the iPad.
Go to Settings>Safari>Clear History, Cookies and Data. Restart the iPad.
Restart the iPad by holding down on the sleep button until the red slider appears and then slide to shut off. To power up hold the sleep button until the Apple logo appears and let go of the button.

I can not print web pages with my HP Deskjet 5440

I can not print web pages with my HP Deskjet 5440. I use Vista, no error page, just prints a blank page with headers and footers. Recently reinstalled printer driver from HP.

Hello , Welcome to the HP Support Forums!
I understand that since upgrading your Mac OS X 10.10 computer to Mac OS X 10.10.4 you have been unable to print colour photos wirelessly from your HP Officejet 5740 e-All-in-One Printer. I would like to assist you today with resolving this colour printing issue. To be honest, it does sound like Mac may have loaded the generic Apple Airprint driver on your printer rather then the HP Full Feature Software and Driver package. Should this be the case then you will only have basic print capabilities. Please follow the steps below to confirm that your HP Officejet is utilising the correct driver on your Mac.
1. Click the Apple menu, and then click System Preferences. 2. Click Print & Scan, and then check if the name of your printer displays in the Printers list. 3. Click the name of your printer, click the minus sign (), and then delete the printer.  4. Click the plus sign (), click Add Printer or Scanner, click the name of your printer, 5. Click the Use or Print Using box, and then select the name of your printer in the pop-up menu. Ensure that the Officejet driver is selected and not the Airprint driver.
  6. Click Add to add the printer to the list.  Once your printer has been installed with the correct HP driver, please test printing a colour photo to confirm that the issue has been resolved. Please respond to this post with the result of your troubleshooting. Should the issue persist there are additional software and driver troubleshooting steps I will have you perform. I look forward to hearing from you!

HT4922 Downloaded 5.1.1. to my iphone. Now, Safari will not connect to my server. Can not download web pages and many of my apps. Running very slow sluggish! Is there a fix? Sound like other users are experiencing same problems. Anyone have a solution?

Downloaded 5.1.1 to my iphone. Now, Safari will not connect to my server. Can not download web pages and many of my apps. Email seems to be ok. iphone running slow and sluggish. I have read several other users have experienced the same problem. Any solutions?

Basic troubleshooting steps oultlined in the User Guide are restart, reset, restore from backup, restore as new device.
You need to go through all steps in succession until your problem is solved. If going through ALL these steps fails to resolve your issue, then you'll need to bring your phone into Apple for evaluation and possible replacement.

Display customers by Type on a web page

I can find any module for displaying customers by type on a web page.
The intention was to have customers entered under a specific Type, and then under a secure zone display them based on the customer type.
Anyon know how this can be done?
Thanks

I have been working with BC (since Good Barry) for years and have had a few clients request the option for their members to create public profiles, so similar situation to what you are talking about. One workaround I have used is having the clients enter their CRM details first (in my case after they subscribe to a secure zone) and then directing them immediately to a page with the Web App Submission form. THAT form can then be pre-populated with the newly saved customer's CRM details using secure zone modules (E.g {module_workphone}, {module_workaddress} etc..). It is not ideal, but reasonably seamless from the client's point of view, as you can populate the form with hidden or read-only fields, meaning they don't have to enter their details twice.
Question for you, Mario - the problem I have always had is that obviously there comes a time when the client wants to update their profile and/or their details on file. I noticed that the EDIT layout of the webapps will NOT populate fields with the CRM modules - setting the values of the fields to {module_whatever} just won't work, as simple as it sounds.. So every time a client wants to (for example) UPDATE their contact details, they have to do it twice (once for the "Update Details" form and once for the "Profile Web App").
Is there ANY way around this?

Can't add web page to existing document

I am new to Acrobat 9 Pro (running on Win7). I love the feature where you can convert a web page to pdf and then add a wab page to an existing document. My probelm is that I saved one page as a pdf then went to a different link on that website that appears very similar and tried to add that page to the first one. As many times as I tried, my second page will not appear.
I did try going to an entirely different website and adding a page to the very same document and I was successful.
Is it possible that the program won't add the similar page because it is recognizing the page to be the same? Is there a setting to override this? I need to be able to save multiple web pages that appear the same way to one document quickly and easily.

Thank you for your response. It is possible to do this but I need the 'Add web page to existing doc' feature to work for me. I will be converting a large number of similar pages to pdf and this feature would be perfect if it worked as it is intended. Going back later to insert pages is counter-productive for me.

I can not print web pages,print box does not appear . I can print web pages using IE

Windows 7. Firefox 5.0 I can not print web pages. After clicking PRINT the print dialog box does not appear and nothing prints. I do not have this problem using IE
Printer: Brothers HL-5140
Thank you,
Syd

First of all, update Firefox to 3.6.17 via Help | Check For Updates.
There was a security breach at Comodo which is an SSL certificate provider recently whereby a number of fraudulent certificates were inadvertently issued. These allow a hacker to impersonate any site including online banking and the Firefox version you're running at the moment will not warn you that the site is a fake. The fraudulent certificates were blacklisted in v3.6.17 and beyond.
To uninstall the Yahoo Toolbar, go to Tools | Add-ons | Extensions. You should find it in there.
To revert to Google as your preferred search engine, please do the following.
* In the location bar, type '''about:config''' and hit Enter.
* In the filter at the top, type: '''keyword.URL'''
* Double click it and remove whatever's in there and replace it with http://www.google.com/search?q=
The URL to add in "keyword.URL" becomes a link in this post, so right click it and choose "Copy Link Location" to copy it to the Windows clipboard. Then hit CTRL+V to paste it. Saves you having to type the whole thing.
'''To reset your home page, do the following'''.
* Go to the site you want to set as your homepage.
* Go to '''Tools '''| '''Options '''| '''General'''
* Make sure it says "''Show My Homepage''" in the first dropdown menu.
* Click the button called "'''Use Current Pages'''" to set the homepage to the one you have on the screen.
After you complete the above steps, install this add-on to prevent another search engine from modifying your preferences: https://addons.mozilla.org/en-US/firefox/addon/browserprotect/
Additonal security risks on your system are the version of Flash you have installed at the moment. See http://www.adobe.com/support/security/bulletins/apsb11-12.html
Update via http://get.adobe.com/flashplayer/
Printing issues might be fixed by installing Java via http://www.java.com/en/
But if the problem persists, please post again.

I can open my web page, but cannot install itunes.

Everytime I try to install itunes, i get message saying check internet connection.
I can open my web page, but cannot update or install itunes.

These issues are usually caused by firewalls. See [[Cannot connect after upgrading Firefox]]

Dual Monitor Issue: 2nd Display too large...can't adjust...web pages provide no scroll bars

Similar Messages

Maybe you are looking for