DV Transfer Issues

I've been using a Canon XH A1 in SD (24F and with the 2:3:3:2 pulldown), and I transferred footage over in Final Cut without knowing a whole lot about what I was doing; I put the Sequence Preset to DV NTSC 48 kHz - 24, the Capture Preset to DV NTSC 48 kHz Advanced (2:3:3:2) Pulldown Removal, and the Device Control Preset to Firewire NTSC.
The problem is that when it gets into Final Cut, it is suddenly quite small. In the preview frame, there is a small box where the video is, and then the rest of the frame is black. This is also the case when I export it as a video to DVD Studio Pro. What am I doing wrong?

Do you also have to render the video when you put it in the sequence?
If so, it sounds like your sequence is the wrong type for your video format.
Did you chose the preset before or after you made the project?
Try making a new sequence and see if that helps. "File/New/sequence"
Even though your sequence preset is set to match your video type it only applies to "NEW" sequences, it doesn't change sequences that have already been made.
Does this help?
Message was edited by: MovieMakers
Message was edited by: MovieMakers

Similar Messages

  • SCP log file transfer issues after upgrade

    We upgraded out AsyncOS from 6.3.3 to 7.1.3 and now we are encountering log transfer issues with 2 out of 3 WSA's. Also the log rotation is set at 3GB but is rotating at 1GB. Anyone have any suggestions?             

    Hi Dominick,
    FIrst look at your log subscriptions for the access logs. Log into the GUI -> System Administration -> Log Subscriptions -> Access Logs highlighted in blue on the left side of the window. Check that your configuration is set to your needs. Next we need to review what is taking place when SCP tries to send the logs to the destination by reviewing the System Logs also located within the log subscriptions. Is the destination a Windows or Linux device ? If it is a Linux device you may also want to look into var/log/secure for the log information there as well.
    Sincerely,
    Erik Kaiser
    WSA CSE
    WSA Cisco Forums Moderator

  • More SMB Slow transfer issues 2012 R2

    Hello All,
         I have read the multiple threads about 2012 Rs and SMB file transfer issues, and I have tried everything I have found on TechBet with no luck.  I have disabled RSS and all the checksum offload options, and I have changed the GPOs
    for digital signing...no luck.  Any advice would be great...
    AB

    Hi,
    Above all please make sure it is caused by SMB. Sometimes network issue could also be caused by hardware configuration or limitation.
    Incase is related to SMB version please test to disable SMB2 to see if SMB1 works fine or not.
    Also here is a forum FAQ article which could help troubleshoot general SMB related issue. Please see the troubleshooting process:
    http://social.technet.microsoft.com/Forums/windowsserver/en-US/7bd9978c-69b4-42bf-90cd-fc7541ccb663/forum-faq-troubleshooting-network-file-copy-slowness?forum=winserverPN
    If you have any feedback on our support, please send to [email protected]

  • Mid Month Transfer Issue in Payroll

    Hello All
    Good Day!
    We have two payrolls defined, Payroll A and Payroll B and both has separate Legal entity but Business Group for both Payroll is same. We are having an issue when employee transfers from Payroll A to B or vice versa as mentioned below :
    1) Lets assume Employee transfers from Payroll A to Payroll B as on 17 Oct 2012.
    2) As Business Group is same , employee remain in the same BG.
    3) So we tried to terminate the employee as on 17-Oct-2012 and re-hired as on 18-Oct-2012 in the Payroll B. We need two IRP5 (tax certificate) so we need to terminate the employee from one payroll and reinstate in new payroll.
    4)) We have most of the recurring element configured to Terminate as Last Standard Process so all the recurring elements ended as on 31-Oct-2012, i think this should have been Actual Termination Date but as Payroll is running from last 2 years so this will be too big to change now.
    5) Now when we process the payroll as on 31-Oct-2012, employee got full month salary in Payroll A which is not correct as employee worked up to 17-Oct-2012.
    6) To avoid full month Salary, we changed the Last Standard Process to 17-Oct-2012 so all elements ended as on 17-Oct-2012 but now when we process the payroll as on 31-Oct-2012, employee is getting picked up but no element processed and no balance generated. Don’t know why ?
    Could you please provide your input as what is the best practice to handle this mid month transfer ?
    Thanks
    Gaurav

    Hi, Gaurav..
    6) To avoid full month Salary, we changed the Last Standard Process to 17-Oct-2012 so all elements ended as on 17-Oct-2012 but now when we process the payroll as on 31-Oct-2012, employee is getting picked up but no element processed and no balance generated. Don’t know why ?
    =>I guess.. The "Final Process Date" set as 31-Oct-2012 when you end this employee, isn't it?
    Actual Termination Date will let person end at this date, that's mean person record's effective_end_date will equal to the Actual Termination Date and create a new person record after Actual Termination Date.
    Last Standard Process Date let all elements ended as this date.
    Final Process Date means you can process payroll run before this date, and the assignment record's effective_end_date will equal to Final Process Date. That's why your payroll run includes this person. There's no elements because all elements ended on 17-Oct-2012, system doesn't get any element on 31-Oct-2012.
    Best Regards,
    Changhua

  • File access / transfer issue - MTP, PTP, bluetooth

    I'm having issues transferring files from my Galaxy Nexus to my PC. First, here are the config of the two -
    Galaxy Nexus - Verizon LTE
    USB debugging enabled
    PC - Windows 7 Ultimate 64 Bit.
    Samsung ADB driver 1_4_6_0 installed.
    When I connect the GNex to my PC via usb on MTP mode, all the folders show up but other than Camera, music, movies etc, other folders don't show their content...!! For example,
    1) the TitaniumBackup folder. When I browse it using ES File explorer on my cell, that folder shows lots of files, all having read permissions. But the same folder in PC window shows up empty.
    2) The apps backup that I created using ES Backup, located at sdcard\backup\apps - shows up on phone but not on PC.
    I even connected the cell on PTP mode. But then only camera folders show up. Duh, PTP IS camera mode.
    So, other than Pictures, Music and Video, I'm not able to move/copy any other file from GNex to my Pc. Geeeez, that's what MTP stands for. Media Transfer Protocol. It can't handle anything else....!!!
    Next I paired my PC and GNex over bluetooth. And lo n behold, all the files show up. Pretty. But now it is "You can look but you can't touch" drama. If I try to copy anything, I get service not available error. Aparently, "Bluetooth peripheral device" driver is not installed. I tried to update those [showing up with yellow ! marks on Device manager], but no results.
    Anyone else facing these issues? Any solutions? Thanks in advance guys.

    How do you create a LAN connection between your cell and PC? On ES File explorer, I select "LAN" from the drop-down snd then menu > New > Scan. It doesn't find anything. Then I try to manually add my PC. I provide my PC's ip address and username password on the prompt. It still gives failure. Both PC & GNex are on same wifi network and connected via usb as well. What am I doing wrong?
    Also, now I'm seeing that when I connect the GNex to my PC, the folders are showing old files; even deleted files; but not new files created since last time I had connected it to the PC. I cleared the system cache and tried connecting it to different port too.. No luck...

  • CUCM 7.1.5 + cue 8.6.7 AA call transfer issue

    The problem I have, happens only when a caller from PSTN calls my AA, the call is answered (the PSTN Caller hears a message) and then transfer to an sccp phone but the destination number does not answer and then the call is redirected to the forwarding destination. The last DN that will answer the call does not receive called id information but only the caller id (PSTN number).
    For example a PSTN user xxxx2232 calls one of our customer service representatives at xxxxx007. The call is answered by CUE AA that plays a message and then the call is transferred back to xx007. In my case xx007 does not answer and the call is forwarded to xx008 which sees on the phone display call from xxxx2232 only and not call xxxx2232 for xxxxx007. When xx008 tries to pick up the call from xx007 the same happens.
    With cue 7.0.3 i had no such issue after the upgrade of my cue to 8.6.7, I have this issue.
    Can help in order to find what is going wrong.
    Thanks.

    CUC yes, for CUPS you need to review the CUPS compatibility info to find that out, for any other Cisco apps, also review the release notes to find if they're compatible or no. For 3rd party apps, check with the vendor
    Sent from Cisco Technical Support iPad App

  • Video transfer issue from iPhone

    Hello!
    I own iPhone 4S and iPad (3rd Generation) and regularily make video with both devices and then transfer the video to my PC via the USB cable and then play the videos in Quick Time on the PC.
    Prior to updating to iOS 6 on both my iDevices on September 19, I had no problems at all. The videos transferred properly and I was able to view them on my PC in Quick Time. Today (September 25), I made a video on my iPhone 4S, transferred it to my PC the way I always have (via USB), and when I opened it in Quick Time, I just got a black screen with no audio. I then tried the same thing with my iPad (3rd Generation) and had the same results.
    The videos played perfectly on the iOS devices on which they were shot.
    Anybody else having these issues? What can I do to fix this?

    in case you ended up on this thread via web search (as I did today),
    I'll post how I solved it when it happened to me.
    the issue was caused by importing 3 months of camera roll using Image Capture (I do not use iPhoto anymore).
    after importing all the items, I selected them all in the Image Capture window and clicked on "delete".
    a few ghost files (video only) were left behind, all of them 0 Bytes.
    tried disconnecting/restarting the device but the issue persisted.
    no way to delete the video references from the mac.
    had to go in camera roll and manually delete them all.
    using "select' on the top right you can tap them and delete after they are all checked.
    hope this helps someone
    u.

  • Itunes 11.1.3.8 video transfer issue

    Hello!
    Im using Itunes11.1.3.8 for transfering my musics, apps, videos and photos from my windows xp pc to my iphone 5s
    but im not able to transfer any videos to my iphone
    pl. help me

    Hi there L.Bear,
    You may find the troubleshooting steps in the article below helpful.
    iTunes for Windows Vista, Windows 7, or Windows 8: Fix unexpected quits or launch issues
    http://support.apple.com/kb/ts1717
    -Griff W.

  • P2 Transfer Idles on select clips - P2 transfer issues in 5.1.4

    Hi this is my first HD/p2 project. I'm having an issue where some clips are idling out when i try to tranfer them to .movs. What's weird to me is that the first day of the shoot, all P2 transfers to .movs went fine. then on the second day for some reason, some of the files wouldn't transfer. And it seemed a bit random which ones didn't. It wasn't based on Folder location or anything. One file would tranfer then the next one wouldn't. I couldn't see any pattern or connection to which file would transfer and which wouldn't. I clearly have all the files on my external (the cards were rented) because I can watch them in the P2 import window. and it's always the same files that don't transfer. I've tried redoing it in another project, I've tried moving the CONTENTS folder to a new drive and then try to re transfer to no avail. Any suggestions that don't involve buying 3rd party software?

    #36 - One or More P2 files failed to import.
    Shane's Stock Answer #36 - "One or more clips failed to import..."
    Very often in the field with this camera the camera operator will delete clips from the P2 card that they just don't like. That is the beauty of this camera. But, the still for that video file (located in the CLIP folder in the CONTENTS folder)...the still that you see when you are in the P2 Import window...is not deleted. So you will see the image, and the name, but the video file would have been deleted.
    What you can do it compare the file names in the VIDEO folder and CLIP folder and see if anything is missing. If something is, then you know what the problem is. You can then just import the rest a few at time, skipping that one.
    ALSO...in the P2 Import window...in the P2 Browser, there is a little sprocket drop down menu. Click on that and choose PREFERENCES. Uncheck REMOVE PULLDOWN and then try importing again.
    ALSO...make sure your file names aren't too long. Try shortening them and see if that works.
    Shane

  • Attachment transfer issue from Shopping cart to Purchase req in ECC

    Hello,
    How are you all. Need your expert advise..
    We are trying to achieve functionality where documents which are attached on shopping cart get transfer into Purchase req in ECC (Classic Scenario with SRM 5.0 and ECC 6.0). For this we have done following config / enhancements:
    - Activated BADI "BBP_CREATE_BE_RQ_NEW" in SRM with following code for attachment;
    cs_ctrl_att-BE_DOC_TYPE = 'SRM'.
    cs_ctrl_att-BE_storage_cat = 'DMS_C1_ST'.
    cs_ctrl_att-TRANSFER_ACTIVE = 'X'.
    - Created new document type ECC with t.code DC30 for SRM and assigned the object links for EBAN table.
    After performing above task we are able to see Link of the attachment into Purchase req in ECC with document number (i.e. the one we assigned while defining document type in DC30) but not able to open the document in ECC.
    Could you please let us know if there is any settings which we have missed for actually opening documents in ECC?
    Thank you
    Ritesh

    Issue as reported Please let me know why the docs are not uploaded to SRm succesfully .
    I am facing the below weird issue .
    Easy shopping >Shop> eHiring catalog
    Click Transfer to SRM
    Now click on the button ‘Details’ and open the tab ‘Notes and attachments’
    All attchments are names after the 1st attachment and all have the same file type
    Basically you have lost all you attachments here, except 1 (when you click on the link, all links refer to the same document, so not just cosmetic). This is a problem.
    When you order this shopping cart and search for it and open it again, the attachment tab is even completely empty, so now all attachments are lost.
    Something like this, but less severe, happens in the process a bit further.
    - Approve the shopping cart with the applicable approver
    - Log in as Hiring desk:
    Still no original attachments (like job descriptions).
    Now click button ‘responses and awards’
    Click tab ‘Items’ and fill out price ‘40’ euro
    Click notes and attachment tab
    I added 5 attachments
    As can be seen here, the docx becomes an xlsx again, but it looks like it just takes over the 1st file type that was uploaded, it can also be the other way around (xlsx becomes docx) when the 1st uploaded attachment is a document.
    But in this case, when you click on the link, it will open the right file with the right program, so over here it looks like it is just cosmetic.

  • Log and Transfer issues

    I have a 2GHz Mac Book Pro with 2 GB or ram. I use this quite a lot when shooting and editing with my Panasonic P2 (HPX2000). Usually, I log and transfer DV, DVC Pro and DVC Pro 50 files with no issues. The other day, I shot a concert in 720P and when trying to log and transfer a 40 minute video, it would not finish. It would show the file transferring, but show the exclamation point at next to it, alerting me that it had problems. I was able to transfer over small chunks and edit them together in FCP, but I wonder if this is a ram issue or something like that. Any thoughts?

    #36 - One or More P2 files failed to import.
    Shane's Stock Answer #36 - "One or more clips failed to import..."
    Very often in the field with this camera the camera operator will delete clips from the P2 card that they just don't like. That is the beauty of this camera. But, the still for that video file (located in the CLIP folder in the CONTENTS folder)...the still that you see when you are in the P2 Import window...is not deleted. So you will see the image, and the name, but the video file would have been deleted.
    What you can do it compare the file names in the VIDEO folder and CLIP folder and see if anything is missing. If something is, then you know what the problem is. You can then just import the rest a few at time, skipping that one.
    ALSO...in the P2 Import window...in the P2 Browser, there is a little sprocket drop down menu. Click on that and choose PREFERENCES. Uncheck REMOVE PULLDOWN and then try importing again.
    ALSO...make sure your file names aren't too long. Try shortening them and see if that works.
    ALSO make sure that the folders that contain the CONTENTS folder doesn't have any odd characters like /!@#$%^&*()?.

  • STS: Portal HTTPS to BSP HTTP transfer issue

    Hi Experts,
    We have the following issue.
    We use portal with SSL, and we put SSL on out BW backend system. We also use STS, and we created a BSP iView in the portal to use STS inside portal.
    The problem occurs when a link to the iView is clicked. What happens is that when the iView is being loaded, all the session cookies are getting blocked for some reason, so that clicking on any link in STS results in timeout error.
    My observation is that STS only uses SSL for the login page. So when a request comes through the portal that uses SSL it goes to a BSP iView without an SSL (you get the warning that you are about to display non-secure items).
    A workaround solution is to goo to IE properties, security/privacy and click the "Allow all session cookies" checkbox. This a bad solution because it involves telling users to configure their browser. I am wondering if anybody had the same or similar issue, and if there is any other resolution then just explicitly allowing cookies in the browser.
    We have another environment setup in QA that does NOT use SSL for either portal or a backend BW, and this problem with cookies does not happen there. I am guessing it has something to do with a switch from HTTPS to an HTTP request when it comes through the portal.
    Please let me know if you know how to resolve this.
    Thank you,
    AG

    Hi Marc,
    Thank you very much. The note helped us ensure that all the STS pages are using HTTPS protocol. There is still one issue remaining though.
    When STS generates its start URL, for some reason it starts with HTTP, not HTTPS. It is evident when you go to BPS_TC tcode and try to execute option "Test call with display of URL". The URL that gets displayed is for example:
    http://test.somedomain.com:8000/sap/bc/bsp/sap/tunguska/start_sts2.htm?teilplan=ZBUDGET&version=002&sap-client=200&sap-language=E
    When pasting this link in the browser, STS automatically redirects you to the https protocol, which is fine if you are using STS BSP application stand alone.
    This represents a problem however, if the application is integrated into portal BSP iView. If portal is running under HTTPS, then clicking on the STS iView causes a warning message to be displayed saying that you are about to be redirected to the page that is not secure because for some reason the very first page STS generates uses http protocol disregarding the fact that HTTPS has been setup for STS. This warning message creates a false assumption that the pages are not secured, while in fact right after the warning message is displayed a redirect to https occurs making sure STS pages are protected.
    My question is there some sort of global setting where you can control the generation of STS start URL? I made changes for every page making sure Transfer Options set to HTTPS, and also made sure Logon page is using HTTPS in the SICF transaction for tunguska and tunguska_detail services.
    At this point we are stuck and do not know what to do to eliminate that warning and how to control the generation of start URL in STS. Any help would  be greatly appreciated.
    Thank you,
    Andrei

  • CLOSE ISSUE - FI PCA transfer issue

    Hello Friends
    We have an critical issue which is holding our close now.
    After transferring AP AR Subledger and PCA transfer we see that some accounts have different balance in PCA compare to FI.
    In detail, we did the following steps -
    Used T Code F.5D Which calculates the Balance sheet Adjustments AP AR documents
    Used T code 1KEK to transfer the AP AR to PCA
    Went to SM37 to process the same
    Checked the Job Log and confirmed that there are no errors
    Used Y_DEV_19000069 report to check whether the balances are transferred correctly to PCA and found the above differences
    Thankyou
    DS

    Hello friends
    Issue was solved . We find those accounts in 3KEH.
    We have to remove them from 3KEH for the amounts to be trasfered to profit centers.
    Thank you
    DS

  • File transfer issues

    I'm attempting to transfer files from my (very) old G4 (running OS 10.4) to my new mini via firewire. I have no problem starting the G4 in target disk mode, but it doesn't show up anywhere on the mini.
    What am I missing here? I've read everything I can find but nothing has addressed this problem. I've skimmed the topics here and also didn't see anything, so my apologies if this has already been answered.
    Thx~
    Deb

    After talking with Apple Support, only to be told to do exactly everything I'd already done a 100+ times, I'm no closer to resolving this issue than I was before. I suppose I could have purchased a bad firewire cable, though it seems kind of unlikely. Or perhaps the firewire ports on the G4 are bad, though they've never even been used.
    I have no other ideas, though. Does anyone have a thought? Please? Am I stuck transferring years' worth of files via ethernet?
    D.

  • EWM CIF Integration Model master data transfer Issue

    Hi Gurus,
    I am not able to transfer the master data from ERP to EWM.
    When I excecute the transaction CFM1 and CFM2 integration model ,the material is not getting transferred.
    I am getting the below mentioned Error message.
    "Location does not exist for external location 9997, type 1040, and BSG CSSCMDEV"
    Please help me in resolving this issue.
    Regards
    Govind

    Hi,
    Thanks for the reply
    I had created the location 9997 for the location type 1001earlier.
    When I tried to delete the location and create new Location for Location type 1040.System is not allowing me to delete.Please let me know how to delete the existing Location.
    Regards
    Govind

  • IAnnotate PDF - wifi transfer issue workaround

    I bought this app because it provided useful tools like highlighting, notes, strikethrough, underlining, etc, of PDF docs. I was extremely frustrated that each time I tried to transfer a PDF to the iPad using the app's AJi Reader Service desktop app, it could cut out my wifi connection. I was close to pulling my hair out over it and demanding a refund.
    Went to their site and there were several folks in the forum having the same issue. Aji tried to say its Apple and their wifi problems; users kept saying no it's not (me included), never had ANY wifi issues before using this app.
    One very clever user figured it out ... if you have bluetooth enabled at the same time you are trying to transfer a PDF it will cut the wifi connection. Turn of BT and it works just fine.
    Aji now knows the issue and will hopefully put out a fix. I think this is a very useful app, so I'm glad to hear someone found it. Granted, the app needs some new features like undo, but overall it's quite nice.

    There actually is but it's not very intuitive. Took me quite a while of playing with the app to figure it out. Once you do a highlight, for example, and save that, go back to the highlight and double tap. A little bar comes up with a small X (among other buttons) to undo the highlight.
    I hope they refine the annotation features soon. It's a bit unwieldy to undo things.
    Message was edited by: dlg_az

Maybe you are looking for