DV4-1125nr black screen on boot up looking for bios flash file taken off hp site or solution

have black screen looking for sp41969.exe for dv4-1125nr to do blind flash. on board diagnosis is 4 flashes (graphics controller malfunctioning) with amber sound and wireless lighting up by keypad not very good with computers so any help in dummy terms would be appreciated if you have the file i need please email to {Personal Information Removed} thanks

HI,
bmbrsoccer4 wrote:
have black screen looking for sp41969.exe for dv4-1125nr to do blind flash. on board diagnosis is 4 flashes (graphics controller malfunctioning) with amber sound and wireless lighting up by keypad not very good with computers so any help in dummy terms would be appreciated if you have the file i need please email to {Personal Information Removed} thanks
Try the troubleshooting procedures on this HP web page.
Best regards,
erico
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Similar Messages

HT4972 My ipad 1 is stuck on IOS 4 as the IOS 5 update instructions do not work. When I use itunes update the software looks for an update file and the apple site doesn't have one!

My ipad 1 is stuck on IOS 4 as these IOS 5 update instructions do not work. When I use itunes update the software looks for an IOS 5 software update file and the apple site doesn't seem have one anywhere!

If you have an iPad 1, the max iOS is 5.1.1. For newer iPads, the current iOS is 6.0.1. For the iPad Mini the iOS is 6.0.2. The Settings>General>Software Update only appears if you have iOS 5.0 or higher currently installed.
iOS 5: Updating your device to iOS 5 or Later
http://support.apple.com/kb/HT4972
How to install iOS 6
http://www.macworld.com/article/2010061/hands-on-with-ios-6-installation.html
iOS: How to update your iPhone, iPad, or iPod touch
http://support.apple.com/kb/HT4623
If you are currently running an iOS lower than 5.0, connect the iPad to the computer, open iTunes. Then select the iPad under the Devices heading on the left, click on the Summary tab and then click on Check for Update.
Tip - If connected to your computer, you may need to disable your firewall and anitvirus software temporarily. Then download and install the iOS update. Be sure and backup your iPad before the iOS update. After you update an iPad (except iPad 1) to iOS 6.x, the next update can be installed via wifi (i.e., not connected to your computer).
 Cheers, Tom

HP DV4-1155SE Black Screen and Wont Boot. Please Help!

Hello all I am working on an Hp DV4-1155SE. I have tested the memory modules, the hard drive and everything else that I can take out of the computer easily. Everything works but!, The laptop will not boot into the bios or anything else. Black screen, wont boot and i have the bios file that HP supplies on the support page of the site. I have looked at the instructions that a few people have posted about re flashing the bios and that does not seem to help me at all with this AMD processor. If anyone can please offer any help at all this would be greatly appreciated.
Thank you!

I will search on int 19h....thanks.
My problem started before the bios-screen.
This is what I tried this evening:
- Disconnected all non-essential devices...no effect.
- Cleared the CMOS...system booted to OS! Screens still garbled!
- Put in an older graphics-card...No artifacts!
- Put my MSI NX6600GT (AGP) back in...screen grabled while booting. Once in OS everything
looks fine at first. Later I noticed some odd random pixels. Playing movies is working fine.
Playing 3D games results in all kinds of strange looking artifacts.
- Installed the latest NVidia- drivers...no effect.
Is my problem still MOBO related or Graphics Adapter?
Any further advice?
Thanks!

[P6N SLI Platinum] black screen NO BOOT after D-bracket replug [RMA-SOLVED]

Quick setup specs;
P6N SLI Platinum
E6600 (box/stock 2400mhz basic)
2x 1Gb DDR2 6400 Gskill HZ
Sapphire ATI X1600Pro (PCI-e basic)
Aerocool Zero DBA 620W
(2 HDs sata, 2 Hds pata, 2 optical pata at first -all OK at first, disconnected after, so irrelevant here ,( )
(XP Pro clean new install from start)
I tried to check the forum old posts before trying to write that new one, but could not find any really related totally adequate posts so far (or i missed them, sorry if so, then -?). I could already find very useful informations on first aid usual 'rebooting' procedures to follow with minimum new boot configurations, d-bracket new LED signals etc. But so far no luck, all same, nothing better, nothing cured here for the stuation here. ,(( Also excuse my english if not perfect, i am not english either. ,(
VERY bad & sad problem here... ,(((( :
All was working perfectly great during 5 days.. the P6N SLI platinum install went GREAT initially (as normal, not a first pc built, all normally happening, so far so good, etc).... all hardwares compatible together at first (dedicated ATX 'full' 8x8 pins connector too for the cpu only for ex -all working perfect at first try. quick tensions 5V/12V under msi dual core control tool perfect too etc), was great easy going/ great strong ultra-stability feeling on the hardware side.. i was just now concentrating on the software side (no special BIOS tweaks even attempted so far, all on basics-normal e6600/ddr2 auto-settings, apart at the end ddr2 quick test -when problem occured- on 450(900?)Mhz at 2.1V, far far easy under its possible specs max anyway.. and had been working perfect for 3 days with that little ddr2 boost try -no time for special bios further tweakings now, etc), reinstalling and transfering/reorganizing slowly my necessary files/hds/softwares from old to new setup, no oc, nothing special tempted (i was planning oc, new cpu more suited fan/silver6 etc only for the end..), LAN file sharing setup done, Realtek audio setup test done, etc ; installation had been so far one of the quickest and problem free ever... explaining maybe also my fatal lack of cautioun for just (too much) 3 sec in the end after 5/- days of perfect working new ring going on.. ,((( :
At first, i also tried to immediately install the D-Bracket too to check possible hardware install problems -very useful feature i of course thought too..and wanted to try too, "in case of"..- (installing it from quick reading of the printed manual..with no colour pic coding inside..and quick error coming from there thereafter with an initial mismatch usb/jbd1 inverted plugs connections.. *both* having the exact same pins numbers and dispositions, beeing side by side on mainboard layout.. and so able to connect both headers indifferently.. so i did not see it immediately (( .. and no way to see it otherwise as such, anyway.. ,( ), just to be sure all was ok. I noticed that LED were of course, never lightning (not normal).. but as EVERYTHING else was working fine (GLAN, sound, etc etc).. i did not bother more than that -- error checking not necessary.
Till that fatal clumsy day i wanted suddenly to.. check the D-bracket too. ((((
All was working well, XP pro opened for hours as usual etc..
i had not yet totally finished to install the motherboard in the pc-case (always on desk, free in sight..)... so i could always see the connections on it. ... and i noticed that ... the colour headers codes were NOT matching (usb=yellow..).. i had just stupidly initially badly connected the D-Bracket jdb1/usb adjacent plugs (inverting them), so... And still, all had ever worked perfect.. except the D-Bracket, of course, was sending back no lights then, obviously.. so i did the fatal error.. confident all was stable enough and strong if even that initial plug error had had no consequences at all.. i did the fatal bad move to try to UNPLUG the D-Bracket connectors and put them back in right orders WITHOUT switching OFF the power supply so... like an hot USB plug, sort of, in a way. fatal error.. :( :( :(
As soon as i began to remove the usb/jdb1 connectors and put them back in normal order... the system suddenly SHUT DOWN ... no special bad noise, no special smell.. just sudden SHUT DOWN.
From there.. impossible ever to boot back again the so far perfectly working machine (((((((((((( , always same till now :
i switch on the power supply.. orange led appears on motherboard (ok)... i switch on the motherboard.. green led on motherboard appears (ok)... CPU fan begins (ok), video fan begins (ok) .... and... NOTHING.. total black video screen. no more even possibility to see the BIOS. :( total dead startup .. and the fans are going on eternally, blocked eternally in that inital startup with leds on too (no sudden shut down after a few seconds.. just.. nothing)... :(
Suprem irony.. the D-bracket LED seems to 'work' now.. "of course". Just the PC no more booting at all ^. Only thing is that only green LEDs are appearing, no red ones... simply the sequence, from start and never changing :
1. GREEN 2. GREEN
3. GREEN 4. (---) (not red, just nothing -?)
If i look in manual, it means "Testing RTC (real time clock)". I don't know exactly what it means *here*, but sounds to me it is the most basic initial first BIOS checking.. and BIOS can't be reached for even that so ; BIOS fried???? :( :(
I tried every 'standard' things recommanded usually here in older posts, for new boots recovery attempts thereafter in such 'boot errors' situations (clear cmos button pushed in every possible ways -quick, long, quick etc..-, removing little by little everything but the very minimal least energy taxing setup; keyboard, cpu, video, motherboard; 1 ddr2 nearest cpu slot.. point).. NOTHING. Worst, i tried to boot with one of those elements missing.. exact same D-Bracket lightning from start to.. eternally (123 GREEN 4-nothing). Even tried to remove the little (cmos?) KTS lithium battery for a few hours -that could work sometimes with the old already ultra-sensitive amd/nforce2 chipset bioses problems, so i tried there too-?-; same 3 green lights and fans running and nothing else happening from there.. ((
Always the same; total dead boot as above. black screen. no possible access to even bios panel. ,(((
So my desperate questions, now: of course, the origin is obvious here; all happened "by my fault" when i tried 'too quickly' to 'hot-plugging' replace correctly the D-BRACKET plugs *without* switching off the power supply... all shut down suddenly when i put back correctly the usb& jdb1 headers... :( ;
- do you think there could be any possible last HOPES to recover the situation that i had missed (a well known situation in such d-bracket handling 'common' (?) connection error, a simple trick to try i had missed ??)
- do you think i FRIED something in the process on the motherboard ?? :( :(
- do you think it is 'only' the BIOS (fried????) ?? :( :(
- do you think i could have fried a specifical external key component in the process (not necessarily motherboard) : ddr2 modules, cpu, video card????? :( :(
- is my only solution is to send the motherboard to RMA (no other ways now) ???
please, don't hesitate to give me any possible hints to try to avoid the RMA process.
can i avoid it, right now?
is that possible to fry an whole board just with such a D-Bracket 'hot plug switch' (on a so far perfectly working -light- setup - no oc, little video card, etc) ???? :( :(
That is the only C2D Intel/ddr2 motherboard i have here around. No possibility to test elements by elements for precise error checking (cpu, ddr2 modules, video card or powersupply).
Only things i could check so far are;
- the power supply (aerocool 620W zeroDBA) ;
i tested it back on my old amd xp-m nforce2 setup.. always working apparently. NOT 'fried' so, apparently. but no way of course to test for exemple the special 8x8 (or 8x4) Intel ATX cpu connector on old xp-m motherboard. But power supply NOt fried at least, apparently -?
- the video card.
no way for me to really test the pci-e card on other motherboard around but.. i tried a very old PCI VGA card.. that one works on old setup.. and on P6N, no effect, doesn't improve the situation. So, not sure the new pci-e video card isn't fried.. but a new video card doesn't correct the dead boot problem.. (
No way for me to test the ddr2 or CPU directly though.
Do you think DDR2 or CPU could have been fried in the process too ???
or just, as i fear anyway, 'simply', the motherboard BIOS fried -??? :-(
Really, thx for any suggestions..
if there could be an 'hidden' trick i did not try yet to try to recover the (initially working perfectly!!! (( ) setup, WITHOUT engaging the motherboard RMA process (at least 2 or 3 weeks lost here to wait the return..online store etc..)....
please, suggest me.. ,((
i am *really* very sad of that stupid clumsy idea to want to 'enable' the D-Bracket.. all was working great so far.. and i lost all with just that stupid idea to try an hot plug bracket reconnection without switching off the power supply it seems.. can it be possible,sigh?? all seemed so stable before that, that i.. just lost my usual cautious just 3 sec too long it seems... :-(
Thanks in advance
hoping post not too long too, but i tried to expose the situation as precisely as possible; first time i ever had such a problem with a motherboard/system install.. that is quiet ironical knowing it was also the best and quickest/easiest easy going new built i ever had so far too.. till then ,( .. and all came from the 'helper' d-bracket 'luxury second hand possible boot helper diagnostic tool' checking in the end too, here.. really hoping i can avoid an RMA process.. and no other hardware elements (apart the motherboard?) could have been damaged in the process ? ,(((

hi, thx a lot for the quick answer. sorry for the length indeed (i did not know exactly how to describe the situation.. without omitting any later possibly important details).
Alas, i already tried that many times in following interesting asnwers on similar problems in old posts here; did NOTHING. ,(
But after your post, i tried it again, and removed for the remaining *hours* (6/8h?) the cmos battery as suggested again *too* so -pushed again the clear cmos button etc when battery out, then when in again, then replugging the powersupply etc; NOTHING better alas too. always same, no boot, black screen, no bios. ,(
Problem always the same, to sum up, for clarity:
power supply on => orange motherboard led is lightning up, motherboard on => green motherboard led is lightning up, cpu/video/case fans are working up as normal and.. that's all. nothing else forever. black screen. no signal. not a single chance to get again the bios setup screen.
another detail i omitted, maybe; keyboard lights are all lightnng up too.. and stay blocked in that state too. tested with 2 different keyboards, same. to shut down the leds, fans etc, only one solution, shut down the power supply button directly, at that stage.
right now, i test on barebone minimal system as recommanded too;
cpu, 1 dimm (closest cpu slot), video, keyboard. all rest disconnected.
i of course tried to reset the cmos with the 'magical red button' many times before, with power supply cable plugged out, pushed the button trying almost every possible way so far (quick, long, long sequences, short sequences etc etc)... changed NOTHING so far -is that thing working?? ,(. and right now, same after hours with cmos battery removed too. ,(
the d-bracket leds are always (now it is correctly plugged..) :
123 GREEN 4 (nothing)
"Testing RTC (real time clock)"
another 'interesting' detail is that; those leds are appearing IMMEDIATELY after the motherboard is switched on, from start (green led appearing on P6N). and it is staying as such till the end. nothing else. i tried to connect also the case speaker ; no bips, no sound signals at all too.
I also remind the system was WORKING like a dream during 5 days *before* i had that sudden TOTAL boot problem.... AND i touched almost nothing in the bios too all along, for initial security reasons too.. (i was concentrating on the software installs anyway right now, NOT on the oc side..). The ddr2 quick little change i did was also the ONLY change i tempted to simply test quickly some setting i already saw working without problem with that P6N and that kind of ram.. and it was working without problem so far too, so.. all the time idem. And it had been perfectly working for 3 days as such untouched from there; no problems at all (those memory modules have been seen on that motherboard largely at those specs, why i did that quick test anyway.. far under their possible max -micron chips). it was even working so well i forgot to put the setting back as default after that quick ram test.. so much it was stable too (even if i had not time to do real memtest test on that one - i did for many hours with the initial automatical default settings too, to check the ram quality, was perfect for many hours, so ok too, no bad ram initially too-; was so stable for all my XP software installs operations etc.. that i forgot it thereafter, to be true..why it stayed like that till that moment (incidently).. but i preferred to mention it 'just in case' though, yes. i also did not push at all the dimm voltages in the process, it was always far inside the specs at 2.05V to be exact -usual for that ram too up to those numbers easy for it. i did not push the ram voltages either so..).
The problem ONLY appears when i wanted to unplug the *initially* badly connected D-bracket headers so (inverted headers.. but that caused NO problems either so far too for the system stability.. only the LEDs were of course not working so far..) : i did the error to NOT switch off the power supply. :(
*then* immediately the system shut down... and above situation appeared. ,(
BUT all was working perfect before.. ram setting included so. ,((
So my simple questions now too ;
- do you know what means *exactly* the d-bracket message 'Testing RTC" (123 GREEN, 4 nothing).. initial bios problem, isn't it?? other ways to recover it now?? ,((
- is it a WELL KNOWN PROBLEM when we try to disconnect and replug too hastily the d-bracket headers without switching off the power supply (*my* main erorr here, it seems :( :( ) ????
... and of course, do you think it could have *fried* another key component (cpu, ram -?? why i reminded the setting, just in case-?-, video card? .. ) with that d-bracket initial disconnection error ... ,(
as i said, i have no secondary c2d/ddr2 motherboard here : no way to test the cpu and ddr2 modules on another motherboard to be sure too here. :( i absolutely can't know if they have been damaged or not, here.. :( :(
any other idea for the motherboard itself though ??? ,(
once again, thx a lot for any suggestions and precisions on that problem (is that a COMMON well known problem with the d-bracket, when we unplug and replug it without extrem care like i did -my main inattention error it seems.. mainly because all was so stable before too.. ((( - without shutting down the power supply/system FIRST ???? can it be possible 'only' that shut down all the system??? (( )
thx in advance again +

Black screen on boot & Diagnostic errors

Hi,
I've a HP g62 notebook pc that has some problems when is booting.
Sometimes the screen is black when i try to boot or i've a BSOD related with the atikmpag.sys.This PC doesn't have warranty, but i don't know if the problem is only because of the SO or if there is any hardware failure.
The PC model is the: g62-b10sp. Product id XF293EA#AB9
System ID 143A
I tried the HP diagnostics wich I retrieved the some test menssages: Memory Test: PASSED
SMART CHECK : PASSED
Short DST : PASSED
Optimized DST : PASSEDHard disk test: PASSED
Battery Test : Primary - Replace
Failure ID: MBQ3W8-5667NG-9XL03F-C0F403 Start-Up Test : FAILED
Failure ID: MBQ3W8-5667NG-9XL03F-X0F403 Run-In Test: FAILED
FAILURE ID: MBQ3W8-5667NG-9XL03F-C0F403 System Tuneup: FAILED
FAILURE ID: MBQ3W8-5667NG-9XL03F-C0F403
Someone from the HP support team could help me?
I wanna know what those failures id are related... They are failures from motherboard/graphics?
Thank you for you attention
Best regards

Hi , Thank you for visiting the HP Forums! A great place where you can find solutions for your issues, with help from the community!
I came across your post about the Notebook, and wanted to assist you! I have looked into your issue about your HP G62-b10SP Notebook and an Black screen on boot showing. Thank you for the error messages and the explanation. Very helpful in diagnosing the issue. The first error Battery Test : Primary - Replace
Failure ID: MBQ3W8-5667NG-9XL03F-C0F403 the Real Time Clock battery needs to be replaced. All the others are the same error message as one can not perform as the Real Time Clock battery needs to be replaced. I recommend to replace the Real Time Clock battery and run the tests again. Here is a link to show you the part number and what you need to do to replace Real Time Clock battery. Page 51 for the part number and shows you how to replace it. I hope this helps, please let me know how it goes. Thanks.

Win 7/Z580: Black screen on boot up, before login screen?

Win 7/Z580: Black screen on boot up, before login screen?
=======================================
I find some interesting posting in this forum. Thanks for keeping this forum to help windows/Lenovo community. I like to pick up the brain of this forum to resolve the black screen issue. I am not sure, whether it caused by virus. I use Microsoft Security Essentials. I am not able to run this in command prompt.
I started my laptop this morning & login screen showed up. Once I entered my login credentials, I heard the sound that usually plays once a login is successful, but I ended up with a black screen. After this occurred, I had to hold down the power button to manually shut down the computer. Once I started it up again, I was prompted to do a system repair, which eventually ended up with all successful outcomes, but I now have a black screen with a cursor before the login screen now. I have no idea what caused this to happen. My laptop is a Lenovo Ideapad Model Z580 (500 GB HD, 6GB RAM).
I am not able to get into safe mode or any other mode, which all leads to a black screen described above. I am able to use the "Repair Your computer" tools after pressing F8 during booting only . All other options leads to Black screen with cursor in the middle
Last Known Good Configuration leads to same
Enable Low Resolution Video (640x480) leads to same My Z580 is not responding to CTRL+ALT+DEL Windows Logo keys as well.
**** I tried SAFE Mode. It loaded couple of drivers and paused at CLASSPNP.SYS load. It went to Black screen with cursor at center.
I am able to invoke control pannel from Command prompt of working PC by typing control.
Z580 PC is not responding to control from command prompt (under Repair Your computer) either.
Z580 is able to use the "Repair Your computer" tools after pressing F8 during booting .
Under local user login it provided Start Repair option. As I pick this option, I got the following. Problem signature
Startup repair offline
1 - 6.1.7600.16385
2 -
6.1.7600.16385
3 - unknown
4 - 21200332
5 - autofailover
6 -
4
7 - NoRootCause
os v - 6.1.7600.2.1.0.2561
locale id – 1033
Under Admin user login, it provided system recovery options. It is not picking up the recovery point created a while ago.
Windows Memory Diagnostics is not launching and shows a black screen without cursor.
I am able to get into command prompt. I tried the following there.
I am not able to run cmd as admin
I reviewed the past posting of this forum on this subject.
Windows 7 boots to an unresponsive black screen with mouse cursor...
System File Checker: Run sfc /scannow & analyze its logs in Windows 7 / 8
Windows Resource Protection could not start the repair service
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program generates in Windows Vista
Force SFC to Run in Windows 7
Windows Resource Protection found corrupt files but was unable to fix some of them
SFC /SCANNOW showed up
"Windows Resource Protection could not start the repair service
I did "net start trustedinstaller"
"Windows Resource Protection detected pending repair restart the computer"
I ran repair options using sfc /scannow /offbootdir=x:\ /offwindir=D:\windows
and got "Windows Resource Protection found corrupt files but was unable to fix some of them "
I did findstr /c:"[SR]" %windir%\logs\cbs\cbs.log >sfcdetails.txt I will be glad to attach the zip file that contain CBS.LOG & [SR] tag extract (xxx.txt).
I did not any find ERRORS there, SFC ended with message saying "found corrupt files but was unable to fix some of them" . It is misleading. There is no [SR] tag pointing to corrupt files. Does SFC through false positive like this?
I ran chkdsk. ResultsFile verification completed.
0 bad file records processed.
0 EA records processed.
CHKDSK is verifying indexes (stage 2 of 5)...
Index verification completed.
0 unindexed files scanned.
0 unindexed files recovered.
Windows has checked the file system and found no problems.
0 KB in bad sectors.
Failed to transfer logged messages to the event log with status 50.
It is puzzling me.
Thanks for helping.

I tried these steps 8/7/2015. I ran chkdsk. Results for D:\
File verification completed.
0 bad file records processed.
0 EA records processed.
CHKDSK is verifying indexes (stage 2 of 5)...
Index verification completed.
0 unindexed files scanned.
0 unindexed files recovered.
Windows has checked the file system and found no problems.
0 KB in bad sectors.
Failed to transfer logged messages to the event log with status 50.
Updated on 8/7
============
Here are my HDD config:
Volume ### Ltr Label Fs Type Status Info
Volume 0 F WDO_Media64 UDF DVD- Healthy
Volume 1 C NTFS Partition Healthy
Volume 2 D Windows7_OS NTFS Partition Healthy
Volume 3 E LENOVO NTFS Partition Healthy
Volume 4 G FAT Removable Healthy
Volume 5 LENOVO_PART NTFS Partition Healthy Hidden
I ran CHKDSK /F /X for C, D, E. All resluted to "Windows has checked the file system and found no problems."
F8 ===> Repair Computer===> Command Prompt ===> Works OK
F8 ===> Repair Computer===> Start up Repair ==> Results into "Startup repair could not detect a problem"
F8 ===> Repair Computer===> System Restore ===> "No restore points has been created on yout computer system drive"
F8 ===> Repair Computer===> System Image Recovery ===> "Windows cannot find a system impage on this computer"
F8 ===> Repair Computer===> windows Memory Diagnostiyics ===> "Black screen with Cursor in the middle"
After getting into Command prompt
I run net user
User accounts for \\
Administrator Guest
The command completed with one or more errors
It did not list other users in my laptop. I do not know why? I tried under F8 ===> Repair Computer===> Command Prompt ===> Works OK
Here is the result:
- Boot with Last Known Good Configuration (F8 menu) ===> Black screen with cursor in the middle
- Restore to a prior date (System Restore) - System Restore ====> Already reported in previous reply
- Try a clean startup Troubleshoot Application Conflicts by Performing a Clean Startup results in
Clean Start up
D:\Windows\System32>runas /user:administrator msconfig
Enter the password for administrator:
Attempting to start msconfig as user "MININT-84TH5FG\administrator" ...
RUNAS ERROR: Unable to run - msconfig
1060: The specified service does not exist as an installed service.
- Try loading defaults in BIOS - F2 ==> f9 ==> f10 ===> Black screen with cursor in the middle
Check if explorer.exe is running and start from CTRL+ALT+DEL (task manager - new task) ===> CTRL+ALT+DEL not responding
Is anybody in this forum point me to fix? Thanks for looking into this issue.

Quad Channel RAM Black screen on boot

So i can run my computer with Duo channel RAM DIMM slot 1 & 3, but if i add DIMM slot 5 & 7 my computer screen just stays black forever. the computer starts up and stays powered on, but no signal to screen. i have tried all 4 ram pieces alone in DIMM slot 1 and the computer boots just fine and it says 4gb ram in both BIOS and my computer properties. I have also tried just adding just one ram piece in DIMM slot 5 and the same problem occurs, just a black screen on boot.
my specs are:
MOBO:MSI X99S SLI PLUS, Socket-2011-3
ATX, DDR4, 4xPCIe-x16, USB3.0, SLI/CFX, M.2
CPU: Intel Core i7-5820K, Socket-LGA2011-3
6-Core,3.3GHz,15MB,140W,22nm,28 PCIe lanes,Haswell
RAM: HyperX Predator DDR4 2133MHz 16GB
4x4GB, DDR4 Non-ECC CL13 DIMM (Kit of 4) XMP Preda
GPU: MSI GeForce GTX 980 Gaming 4GB PhysX
PSU: Cooler Master GX 750W PSU
ATX 12V V2.31, 80 Plus Bronze, Standard, 4x 6+2pin
I have Flashed the BIOS to 1.5, swapped around on the RAM pieces to no avail.

Quote from: badboy2k on 24-December-14, 13:20:22
some people are having problems with that board! (no idea what is going on with it)
just for the sake of problem checking can you take out your CPU and look at the pins in the cpu socket with a bright light and a magnifier (check multiple angles) to see if any of the pins are bent?
a few of the pins are indeed a little bent out of position, would it be best to return the board or should i be able to bend them back into the correct position?

E531 black screen when booting (90% of attempts to boot)

Hi All,
My laptop is 15 months old and has worked flawlessly until last week (this behavior started all of sudden).
In 90% of the times I try to boot my E531 it just shows a black screen, even not possible to enter BIOS.
Then I have to press and hold down the power switch and then retry to boot.
After a couple of retries the laptop boots as normal and functions flawlessly.
I already removed the battery, pressed power button for 60 seconds and then reboot,sometimes it works and others it doesn't.
Hardware diagnostics did not find any issues.I tried to update the BIOS (v1.22 to v1.29) using windows tool and bootable CD-rom but without success (Update using tool does not work it give me error "failed to read BIOS", CD update gives an error that the necessary files are not on the CD).
anyone have an idea what's wrong ?

Hi, do you have NVIDIA dedicated graphics? If so, the graphics could be failing.
Otherwise I'd be looking at a motherboard fault.
But try this, sometimes if a laptop cannot communicate with the HDD it will black screen - Remove the HDD and see if the black-screen issue still occurs (Obviously wont boot to OS without HDD but we are diagnosing at the moment.)

970 GAMING black screen when boot on cold start, have to clear CMOS everytime

I have 970 GAMING w/ FX8320, it shows black screen when boot on cold start, have to clear CMOS everytime to enter default.
I have updated it to the up to date M11 bios. Once it boot up, it functions OK no matter whether you reboot or reset it. But after turned off a few hours (cooled down), it shows on black screen again on boot, all LED lights up OK, but I can hear the fan like keep rebooting, any idea?
PSU seasonic 430W, GPU HD7750.

In what DIMM slots did you insert your memory? I just got and at this moment building a new computer with a 970.
A horrible experience I had with my last build reminded me of it. My board was am MSI A88XM-E45. DIMM1 is blue, DIMM2 is black, DIMM3 is blue, & DIMM4 is black. When using two sticks of RAM, it says to install one on DIMM1 & the other in DIMM3 (Makes sense... After all, it's color colored that way).
Well it would not boot. I reseated every component and for HOURS tried almost everything. Finally I decided to place my two sticks of RAM in the first two DIMMS and viola!
I think I will begin this build the same way.

Mac Pro intermediate black screen at boot after installing mountain lion

I have a 2008 Mac Pro tower, but since installing Mountain Lion I now get a random black screen at boot. Unplugging the apple cinema 20' power supply for 15 minutes seems to clear the fault. Have had no such problems with other OS until Mountain Lion, seems OK when booting to Snow Lepoard on my other drive?
Anyone have the same fault?

Thanks for trying the help! I tried every version of start up, but with no screen it was no good..
Finally solved the problem, it was the ATI HD 2600 XT graphics card that was dying a very slow death.
Replaced it this morning with a GT120 Nvidia.
Anyone with this card should Google it, as apple did a big recall on these..
http://www.itproportal.com/2011/02/21/apple-extends-warranty-mac-pro-video-cards /

Black screen at boot MSI Z77A-G43 with HD7850

Hi,
I've tried everything You suggested in this topic. I've upgrade and downgrade bios (official 2.3, 2.4, 2.8, 2,9 / beta 256, 281,296) few times but still is black screen at boot. Now i'm on the newest beta bios 296 and still same issue on Sapphire HD 7850 with my Z77a-G43 board. I know for sure that sapphire working well because I've checked on other mobo with even worst PSU (400W instead 550W Volcano). Before hd 7850 I had gtx460 and swith those few times and always gtx460 works fine, so I don't understand anything right now.
Tried different slots, also clear cmos.
Board: MSI Z77A-G43
Bios: Version 296
VGA: Sapphire HD7850 1GB
PSU: Modecom Volcano 550W
Intel Core i5-3570k
MEM: Kingston 4GB 1600MHz
HDD: 2xSSD
Without OC
OS: Windows 7 64bit Professional
Can You help me somehow, maybe I did not check something else?

Quote from: The CPU Whisperer on 22-April-13, 16:06:05
Do you see the same problem on bios 2.90?
The Z77A-G43 seems the have difficulties accepting HD7xxx AMD VGA cards lately.
It seems that the problem is gone. I thought of it being an ATI driver issue ~ but not even the latest didn't fix it. But since I flashed to BIOS 2.9 I haven't encountered the problem anymore. So I believe something is fixed between 2.3 to 2.9.
However my problem was a bit different that the OP has.
Oh, and I said this on other thread so I say it here too: MSI and Asus 7xxx cards haven't faced the kind of issues Sapphires are having. I'm so glad to my choice... as I almost picked Sapphire but then read comments on Newegg which weren't in favor for Sapphire.

Black Screen on Boot using mac pro os snowleopard 10.6.6

I get a black screen on booting my macpro with os 10.6.6 after the booting is done the screen activates automatic. i do hear the startup sound but dont get the startup screen with the apple logo.
also my mouse does strange things like not responding on a mouseover juming around the screen and pressing buttons i don't press. Never had these problems before until this morning whenn i booted my mac pro. Please help

Could be your monitor power supply is going. could also be 10.6.6 so first try to get back to a OSX which did not give you problems.

Fixed black screen on boot, passwords not working now

After fixing black screen on boot with the advice provided by the great community. (Here: https://bbs.archlinux.org/viewtopic.php … 9#p1501989 )
I followed the method outlined in the post I reference. Booting from live USB, mounting my root home and usr partitions, arch-chrooting into the root partition and then setting modeset=0 in radeon.conf and putting radeon in MODULES in mkinitcpio.conf then running mkinitcpio -p linux. Afterwards I exited the chroot and unmounted all partitions.
This fixed the blank screen, but all of my passwords are changed. The root and my user account passwords don't work. So again I booted into hot usb, mounted partitions, arch-chrooted in, and ran passwd to change root pw and then su to get to my user account to run sudo passwd. After doing so, I exit the chroot and try to unmount the partitions. I can unmount /dev/sda2 (home) but no sda1 (root) or sda3 (usr). It says: cannot umount /mnt/arch target is busy or cannot umount /mnt/arch/usr target is busy. It suggest lsof(8) or fuser(1) but either I use them wrong or they don't help. If I just reboot at this point my passwords still don't work. Why can I not unmount usr or root partitions? It says they're busy but ps -ax shows nothing. Any ideas? If more info is needed I will promptly supply it, I want to get my arch box up and running again asap
Take care fellow archers

Forgot to mention when I boot into Arch normally, it does systemd-fsck on all the partitions they all pass but after checking /dev/sda2 (home) it freezes. The messages displayed are:
running hook [udev]
Triggering uevents
performing fsck on /dev/sda1 /dev/sda1 clean xxxx/xxxx files, xxxx/xxxx blocks
mounting /dev/sda1 on real root
running late hook [usr]
mounting /dev/sda3 on /usr
running cleanup hook [shutdown]
running cleanup hook [udev]
Welcome to Arch Linux!
kvm: disabled by bios
systemd-fsck[252]: /dev/sda2 clean, xxxx/xxxx files, xxxx/xxxx blocks
and it freezes here if I switch TTY's none of my passwords work.
Thanks in advance
Last edited by cshenkan (2015-03-03 04:37:00)

Blue to black screen at boot up.

I'm running 10.6.8 Mac Pro and getting blue to black screen at boot up. I am only able to log in by safe mode only, please help...

Do you get:
Chime
gray screen
Dark Apple
Spinner
Spinner spins for the usual amount of time
screen goes blue or black at the point where you would normally login?
That is exactly when the graphics card is shifted to automatic. Although that also is the point when added kernel extensions have been loaded and are made active, users report this symptom often correlates with graphics card failure.
Safe Mode does not use the driver or automatic mode, so being able to operate in Safe Mode adds credence to graphics card failure.

Familiar Story - tx2000 - lights and fan on, but black screen at boot up

I've been reading around that there's a common problem with the 1000 series of tablets. After 1 1/2 years, the sucker gets a black screen at boot up, yet the lights are on.
Well, almost a week to my tx2000's 1 1/2 year date (and now out of warranty), I tried to take my tablet out of hibernation. The screen was black yet the lights were on and I could hear the fan.
I tried basic troubleshooting with the online tech, but to no avail. It doesn't work, and they tell me it'll cost about $400 for it to be picked up and repaired. Anybody got a viable solution, or do I just need to go ahead and start saving for a Mac?
Thanks HP for reselling such faulty merchandise.
http://www.mycheaplaptop.net/2009/03/never-buy-hp-laptop/

So this most likely does not apply to the tx1000 problem, but I believe the tx2000 recent problem is not related.
For those getting lights and fan on.. or perhaps on for a second or so but no boot screen or logo it maybe related to your video card driver.
Sounds crazy right? Well your video card driver controls how your computer goes into hibernation and sleep. If the drivers are incorrect the system may not handle this process correctly when you try to reboot it.
I'm not certain on how to get the system to boot up again, but I've done it quite a few times while trying to revive the machine.. pulled the battery.. the ram.. held the power button.. lots of cussing.. the solution seemed different each time, but eventually if you can get back into windows you'll find that either by not using hibernation/sleep or by loading the original video card drivers from the hp site, you'll avoid this problem again.
This problem started occurring for me after microsoft made available a driver update on windows update this past summer.. then suddenly everyone started having issues at the exact same time.. I've seen it blamed on simultaneous heat issues around the world caused by exactly 1 year and 2 months of dust collection on every tx2000 laptop... however I'm quite certain it's the new video drivers in combination with hibernation/sleep.
But don't take my word for it. For more information on how video drivers can affect the boot process check this site: http://articles.techrepublic.com.com/5100-10878_11-1046825.html

DV4-1125nr black screen on boot up looking for bios flash file taken off hp site or solution

Similar Messages

Maybe you are looking for