Dv6 ram upgrade
hello,
recnetly i've been looking for rams to upgrade my notebook but cant find the exact one needed.
currently it has 4gb ram (2gb in each slot) and i want to increase it to 8gb(4gb in each slot) also it has samsung ram so do i look for samsung only or any other company.
i want to know the exact rams specs that would support my motherboard coz there are lots of different rams in market with diff specs and i dont want to waste my money...plz reply asap...
model : pavilion dv6 i5 M460 2.53Ghz 4Gb DDR3
thanks..
The original module HP 4 GB 1333 MHz that is in the manual, today was replaced by a compatible 1600 MHz.
http://partsurfer.hp.com/Search.aspx?SearchText=599092-001
Kingston is equivalent modules but are discontinued.
599092-001 KTH-X3B/4G 4GB 1333MHz SODIMM
641369-001 KTH-X3C/4G 4GB 1600MHz SODIMM
Maybe you can get some:
http://www.amazon.com/Kingston-1600MHz-SODIMM-KTH-X3C-4G/dp/B0084IELNC/ref=sr_1_2?s=electronics&ie=U...
Regards
Similar Messages
-
hi
i just want to know is it possible to upgrade my laptop's (DV6-7040tx) ram to 16 gb ddr3 ? i m not into much technical stuff so if you guys can recommend the best option available for my laptop ,it will be awesomeHi,
Currenntly it has 4+2 therefore you can't get 8+6. You can have 2 + 2, 4+ 2, 4+4, 8+ 2, 8+4 and 8+8 configuration. In this case, you can have 4+4 (throw away 2Gb) or 8 + 4 (also throw away 2Gb) or 8+8 (throw away both).
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem. -
Can i do 16 GB RAM Upgrade (8GB x2) For my HP DV6 7052SR ?!
Can i do 16 GB RAM Upgrade (8GB x2) For my HP DV6 7052SR ?! If yes what is the good RAM for me ?
Hi,
Maximum of 8Gb RAM is supported for unit with 32 bit OS. If the unit as 64 bit OS, then you can upgrade upto 16GB as listed in the manual.
"I work for HP."
Please click the "White Kudos" star to say thanks for helping.
Please mark "Accept As Solution" if my help has solved your problem. -
HP dv6-6c75sa Windows 7 64-bit RAM upgrade
I am running an HP dv6-6c75sa on Windows 7 Home Premium 64-bit, with an Intel Core i3-2350M processor. My installed software is a combination of 32- and 64- bit compatible.
When I purchased the computer, I installed a RAM upgrade which took the total onboard RAM to 8GB. Due to a system issue which I cannot now recall, a search query informed me that my system would only recognise 6GB of what I had installed.
My computer is now 2 years old, and to extend its lifespan, and help it keep up with a recent software install which it cannot seem to cope with (Native Instruments Traktor 2, and Kontrol S4; I would like to make a new RAM upgrade.
I think that the reason only 6GB of my 8GB installed was recognised, may have had something to do with the 32- vs. the 64-bit system, but I can't be sure.
I know that the maximum RAM for Windows 7 Home Premium is 16GB. What changes could I make now that would allow my system to work at or near 16GB of RAM capacity?
Also, where I have a mishmash of 32- and 64-bit software, on a clean install running 64-bit, I believe that I should be able to get all of my software running again. Are there any traps I should look out for that may hamper this.
Do you think that my processor is the thing that is limiting my RAM capacity?
I would appreciate your input.Hi @hyfpxm ,
Thank you for visiting the HP Support Forums and Welcome. I have looked into your issue about your HP Pavilion dv6-6c75sa Notebook and concerns with system recovery.
Here is a document on performing a system recovery. Here is a document on troubleshooting issues with performing a system recovery.
Always back up important information before attempting a recovery.
This system supports up to 8 GB DDR3 10600 1333-MHz and I would recommend 2- 4s. Here is a link to the manual page 60 for the memory. If the specs are correct for your memory I would reseat it.
Use the built-in Windows System Information utility to view information on Operating System, CPU type and speed, 32Bit or 64Bit design, and installed RAM memory. The section marked Find specifications using Windows System information.
Hope this helps.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping! -
Dv6-1122us, upgrade confusion? SSD an option for me?
Ok, I've recently ran a system test in BIOS for the HDD. Short test>passed Long test>failed (almost immediatly). I spoke with HP support and they were awesome. I have a new drive on the way, no cost to me at all. While chatting with the tech I asked if i could upgrade to a faster & larger drive. Well that was out of the question but he also told me that I couldn't get a faster drive, only larger. Currently i have a 5400rpm 320G drive. He told me I could go to a 5400rpm 500G, my user manual states that there are 7200rpm models that go in this dv6-1122us. So
Question #1: Can I install a 7200rpm drive in this laptop that is on my user manual parts list? Or maybe a SSD?
Or are these user manuals not very specific, covering many different models of the dv6?
If so how can i find specific upgrade options for my laptop?
If there is not enough information here to make a wise decision just let me know!
Thanks in advance!!
Message Edited by Drenaline on 11-16-2009 12:31 PM
Message Edited by Drenaline on 11-16-2009 03:30 PM16GB RAM upgrade + an SSD upgrade (biggest wallet can afford).
However, if it is a 13" model, there is an inescapable wall, since those carry just a single GPU and share the video memory with the rest of the apps. 15" and 17" models have a higher powered, separate and autoswitching GPU and up to 1GB of dedicated VRAM. -
HP Pavilion dv6-6170ee upgrade
Can i upgrade HP Pavilion dv6-6170ee to 16 GB RAM?
This question was solved.
View Solution.Hi,
The following link shows its specs:
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c02982007
8GB is the max. BUT Crucial says for a similar machine:
http://www.crucial.com/upgrade/HP-memory/Pavilion+DV6+Series/Pavilion+dv6-6170us-upgrades.html
but not the following:
http://www.crucial.com/upgrade/HP-memory/Pavilion+DV6+Series/Pavilion+dv6-6172nr-upgrades.html
Confusion isn't it. To be at the safe side, I would follow the specs.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem. -
Memory modules can we use for RAM upgrade of HP Pavilion dv5-1198de??
What memory modules can we use for RAM upgrade of HP Pavilion dv5-1198de??
Max RAM? Vista? Windows 7?I can't find a dv5-1198de but I did find a dv5-1198er which should be similiar. It states up to 8 gb of ram. HERE
I would try www.Crucial.com for suggested memory ,you can use their Scanner Tool to let it detect what you have and what you can upgrade/replace with.
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others** -
RAM upgrade on Satellite L300-20D
I was wondering if the laptop L300 - 20D.
Can get a ram upgrade. It has 1024 MB RAM 800MHZ. And i need 1500 MB .Your notebooks RAM can be upgraded up to 4 GB.
For upgrade you can use follow RAM modules:
512MB DDR2-667 - PA3511U-1M51
1GB DDR2-667 - PA3512U-1M1G
1GB DDR2-800 - PA3668U-1M1G
2GB DDR2-667 - PA3513U-1M2G
2GB DDR2-800 - PA3669U-1M2G
Bye -
MacBook Pro 13' Early 2011: Still Slow After 16GB RAM Upgrade
Hi,
I have a MacBook Pro 13' Early 2011 running Yosemite. After the RAM upgrade to 16GB, the speed of the computer is still not satisfactory, having some lag times in launching softwares and startup. Please suggest me what to do. Below is the report. Thank you!
Problem description:
The computer is still running slow even after the RAM upgrade to 16GB.
EtreCheck version: 2.0.11 (98)
Report generated November 18, 2014 at 5:40:20 AM EST
Hardware Information: ℹ️
MacBook Pro (13-inch, Early 2011) (Verified)
MacBook Pro - model: MacBookPro8,1
1 2.3 GHz Intel Core i5 CPU: 2-core
16 GB RAM Upgradeable
BANK 0/DIMM0
8 GB DDR3 1600 MHz ok
BANK 1/DIMM0
8 GB DDR3 1600 MHz ok
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
Intel HD Graphics 3000 - VRAM: 512 MB
Color LCD 1280 x 800
System Software: ℹ️
OS X 10.10.1 (14B25) - Uptime: 0:7:52
Disk Information: ℹ️
ST9320325ASG disk0 : (320.07 GB)
S.M.A.R.T. Status: Verified
EFI (disk0s1) <not mounted> : 210 MB
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
Macintosh HD (disk1) / [Startup]: 318.84 GB (156.62 GB free)
Encrypted AES-XTS Unlocked
Core Storage: disk0s2 319.21 GB Online
MATSHITADVD-R UJ-8A8
USB Information: ℹ️
Apple Computer, Inc. IR Receiver
Apple Inc. FaceTime HD Camera (Built-in)
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
Kernel Extensions: ℹ️
/System/Library/Extensions
[loaded] com.Cycling74.driver.Soundflower (1.5.2) Support
[not loaded] com.marvell.kext.USBGenericPrinterClass (1.0.0) Support
[loaded] com.rim.driver.BlackBerryUSBDriverInt (0.0.74) Support
[not loaded] com.rim.driver.BlackBerryUSBDriverVSP (0.0.74) Support
[not loaded] com.wacom.kext.pentablet (5.3.0 - SDK 10.8) Support
Launch Agents: ℹ️
[loaded] com.google.keystone.agent.plist Support
[loaded] com.oracle.java.Java-Updater.plist Support
[running] com.rim.BBAlbumArtCacher.plist Support
[running] com.rim.BBLaunchAgent.plist Support
[running] com.wacom.pentablet.plist Support
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist Support
[loaded] com.google.keystone.daemon.plist Support
[loaded] com.macpaw.CleanMyMac2.Agent.plist Support
[loaded] com.microsoft.office.licensing.helper.plist Support
[loaded] com.oracle.java.Helper-Tool.plist Support
[loaded] com.oracle.java.JavaUpdateHelper.plist Support
[running] com.rim.BBDaemon.plist Support
User Launch Agents: ℹ️
[loaded] com.adobe.ARM.[...].plist Support
[loaded] com.macpaw.CleanMyMac2Helper.diskSpaceWatcher.plist Support
[loaded] com.macpaw.CleanMyMac2Helper.scheduledScan.plist Support
[loaded] com.macpaw.CleanMyMac2Helper.trashWatcher.plist Support
[not loaded] com.valvesoftware.steamclean.plist Support
User Login Items: ℹ️
Dropbox Application (/Applications/Dropbox.app)
Internet Plug-ins: ℹ️
JavaAppletPlugin: Version: Java 7 Update 71 Check version
o1dbrowserplugin: Version: 5.38.6.0 - SDK 10.8 Support
WacomNetscape: Version: 2.1.0-1 - SDK 10.8 Support
Default Browser: Version: 600 - SDK 10.10
Flip4Mac WMV Plugin: Version: 2.4.0.11 Support
WacomTabletPlugin: Version: WacomTabletPlugin 2.1.0.2 Support
AdobePDFViewerNPAPI: Version: 11.0.09 - SDK 10.6 Support
FlashPlayer-10.6: Version: 15.0.0.223 - SDK 10.6 Support
Silverlight: Version: 5.1.10411.0 - SDK 10.6 Support
Flash Player: Version: 15.0.0.223 - SDK 10.6 Support
QuickTime Plugin: Version: 7.7.3
googletalkbrowserplugin: Version: 5.38.6.0 - SDK 10.8 Support
SharePointBrowserPlugin: Version: 14.4.6 - SDK 10.6 Support
AdobePDFViewer: Version: 11.0.09 - SDK 10.6 Support
DirectorShockwave: Version: 11.6.5r635 Support
User Internet Plug-ins: ℹ️
CitrixOnlineWebDeploymentPlugin: Version: 1.0.105 Support
WebEx64: Version: 1.0 - SDK 10.6 Support
3rd Party Preference Panes: ℹ️
Flash Player Support
Flip4Mac WMV Support
Java Support
Time Machine: ℹ️
Mobile backups: OFF
Auto backup: NO - Auto backup turned off
Volumes being backed up:
Macintosh HD: Disk size: 318.84 GB Disk used: 162.22 GB
Destinations:
LACIE SHARE [Local]
Total size: 350.07 GB
Total number of backups: 5
Oldest backup: 2012-07-17 01:12:57 +0000
Last backup: 2014-03-19 07:05:24 +0000
Size of backup disk: Too small
Backup size 350.07 GB < (Disk used 162.22 GB X 3)
Top Processes by CPU: ℹ️
9% mds
6% WindowServer
1% BBLaunchAgent
0% AppleSpell
0% fontd
Top Processes by Memory: ℹ️
103 MB mds_stores
86 MB Dropbox
86 MB ocspd
69 MB com.apple.WebKit.WebContent
52 MB Safari
Virtual Memory Information: ℹ️
13.07 GB Free RAM
1.71 GB Active RAM
740 MB Inactive RAM
1.66 GB Wired RAM
1.31 GB Page-ins
0 B Page-outsFirst go to the RIM web site and look to see if they have an uninstaller for the device you had. Some times a reinstall of the application and then running the uninstaller is required for complete removal.
If no uninstaller is available, then you will have to use Spotlight to find all items with 'Blackberry' and 'Rim' in the titles. I would also download EasyFind and use that to locate such files. Often it will locate items that Spotlight misses.
Ciao. -
HP Envy 13 1030nr. Windows 7 64-bit. RAM upgrade help.
I just purchased a RAM upgrade for my Envy 13 and I was trying to figure out how exactly to access the memory module. I couldn't find a youtube video for the Envy 13 and reading the maintenance manual provides only partial instructions to access the memory module. It tells you what you need to do (Disconnect the TouchPad cable 2 from the low insertion force (LIF) connector on the system board) but not how to do it without damaging the computer. I don't want to permanently sever a cable or anything so I'm looking for help via a link to a video or more detailed instructions on exactly how to safely access the memory module.
I was under the impression that this would be a quick replacement, but the more I read the manual, the more I think that this is going to be a little more complicated than opening up the bottom and removing the current RAM chip and replacing it with the one I have. Any help would be appreciated. Thanks!Here is the Manual:
Manual
Memory is indeed on the motherboard and getting there requires nearly complete disassembly. See Page 4-26. Not sure how this qualifies as "easy" and if you have not done this before you should get some help. And yes, keep careful track of those screws. -
Hard Drive and RAM upgrades for latest 15" MBP
I'm minutes from ordering a new MBP. Only concerns are whether I get hte Apple upgrades or shop around.
I like this Hard Drive...
http://www.compu2000.com/index.php?l=product_detail&p=6433
And this RAM upgrade...
http://www.a-power.com/product-10937-311-4
If these are equivalent to the apple options I can save hundreds and get a 320 GB drive, which will make a great portable.
So, does my plan hold water?You're on your own for support when you do your own upgrades like this, but generally speaking, it works fine.
Note that HDD is less risky than RAM. With RAM you run the risk of unstable behavior that is tougher to diagnose. That said, a quality RAM upgrade and some initial testing with any of many available tools is as good as a factory build.
HDD upgrades are less risky, and I've upgraded (well, replaced after HDD death) ones in my MBPs many many times. I crunch my hard drives more than normal and have to generally replace them about every year. Some of the MBPs don't make this easy, and prepare to get all sorts of cozy with little 0 and 1 sized Phillips screwdrivers and some T6 as well, but it is doable (just not quite for the truly faint of heart).
Again, you're on your own for support once you do this, so weigh that in your decision. -
Hi there,
I'm hoping to seek the expert views of the community here.
I have a MacBook Pro, Late 2011, 17 inch. Running latest version of Mavericks. Speed seems to have slowed somewhat, perhaps since I upgraded to Mavericks, but not certain about that. Based on my research of the Apple communities, I suspect that I may benefit from a RAM upgrade.
Attached are a few screen shots to assist:
Based on what I have researched in the community, the fact that I have used 3.99GB of 4.00GB, and have used 5.63GB of Virtual memory, seems to suggest to me that I have well and truly maxed out my RAM. Also there is a high number of read ins/outs (but it had been a wheile since I last did a restart on the MBP (if that has any effect on these numbers here).
I have also read that my model of MacBook Pro is upgradeable to 16GB of RAM (2 x 8GB).
Thoughts and views from the community would be greatly appreciated. Will additional RAM help the speed and performance of my MacBook Pro?
Many thanks.More RAM is always a Prudent move...
Kerrod wrote:
Will additional RAM help the speed and performance of my MacBook Pro?
It will certainly help with Performance.
Macs can be very Fussy about RAM...
You can use these Links to check which RAM is suitable for your Mac...
http://eshop.macsales.com/shop/apple/memory/
http://www.crucial.com
It is Important to get the Correct and Matching RAM
Those sites also have videos on how to Install RAM should you need it.... -
Video will not play on Canvas or NTSC after RAM upgrade
editing on a G5 v. 10.4.11, Dual 1.8 Ghz G5 with a recent upgrade to 4GB of ram. Have an AJA IO LA
After the RAM upgrade, FCP timeline will play but video is black in the canvas and image is frozen on the NTSC. Video WILL play in Viewer but no audio.
All cables have been checked to make sure they were put back correctly - will keep checking for errors in re-cabling computer.
Have tried refreshing displays and other tests with displays. Any info would be greatly appreciated.
Thanks!pull the ram, problem goes away? - bad ram
you can pull 2 sticks at a time to isolate which chip it is.
did you get it from a good source - Crucial.com is my favorite, OWC is popular too - both have lifetime warranty -
24" iMac (Primo 2009) strange RAM upgrade issue
I have a 24" iMac (Primo 2009) at work. I been granted a RAM upgrade by the IT department and have received 2 indentical 4 GB modules.
The 24" iMac (Primo 2009) uses 1066 MHz DDR3 modules and supports up to 8 GB RAM in 2 slots. I have purchased RAM from this source http://www.dustin.dk/product/5010642132/corsair-4gb-ddr3-1066mhz-1x4gb-so-dimm-i mac-macbook-macpro/#intcmp=searchProvider_SiteSeeker (Corsair Mac Memory so they SHOULD be fine.)
Here's the issue:
I had 2x 2GB modules. I have taken both out.
I have inserted the new 2x 4GB modules but the machine refuses to boot. It gives off 3 beeps-interval-3 beeps-interval (repeats).
I took out one of the 4GB modules from slot B. It boots.
I inserted the one I removed in slot B again so we're back at 8GB. same beeps. No boot.
I switched the 2 4GB modules from slot A+B around. Now beep-interval-beep-interval (repeats) No boot.
I inserted one 4 GB in slot 1, and one of the old 2 GB in slot 2. It boots with 6GB RAM.
I inerted only the one that won't boot when in slot B in slot A, beep-interval-beep-interval (repeats) No boot.
OK - so logical deduction tells me one of the new 4GB RAM modules is defective. No matter what configuration, booting fails with that specific module inserted, though there are different beeps. I also know tha both slots work since the machine works with 6 GB RAM (2+4).
So I called Dustin, and since we're a big customer they sent a new moduel for free. But, I have the same isssue with the new module!! What are the chances I have recived 1 working and 2 defective modules? not big right? So my iMac seems fine with the old 2GB modules and one of the new 4 GB modules, but says no to the 2 other 4GB modules.
YES - I have tried resetting PRAM and SMC to no avail. Any clue?Switched the 2 modules around, so there's now a 2GB in slot A and a 4 GB in slot B. Still works fine
Model Name:
iMac
Model Identifier:
iMac9,1
Processor Name:
Intel Core 2 Duo
Processor Speed:
2,93 GHz
Number of Processors:
1
Total Number of Cores:
2
L2 Cache:
6 MB
Memory:
6 GB
Bus Speed:
1,07 GHz
Boot ROM Version:
IM91.008D.B08
SMC Version (system):
1.45f0 -
Kernel Power error after Win 7 and RAM upgrade
Hello,
I posted earlier on the subject of win7 and ram upgrades. I did both and it seemed to go fine. I did the ram first ... replaced a 667Mhz 1gb with a 800Mhz 2gb. A couple of days later the computer just shut itself down and restarted. Since then it has done it another 5 times, seemingly at random. Yesterday I decided to spend some time looking into it and found the 'event log'. All the shutdowns are recorded as 'critical'. A search on the web/here showed other occurences of the fault associated with drivers as much as anything.
After I did the win update I did update almost every driver with ones from this site.
Other than the shutdowns the only issues I have which are of very mild concern are the length of time the fingerprint reader takes to be present and that occasionally the cursor is unavailable for about a minute after logging on. When you try and control it it jumps about anywhere but where you want it to go. I rolled back the alps driver and that seems to have sorted the cursor issue.
So, details of the shutdown from the event log are as follows.
Log Name: System
Source: Microsoft-Windows-Kernel-Power
Date: 16/01/2011 16:21:31
Event ID: 41
Task Category: (63)
Level: Critical
Keywords: (2)
User: SYSTEM
Computer: (removed by me)
Description:
The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly."
There's more (I've shown it all below) but it's not that important. When I looked into it I found details of the problem on the microsoft knowledge base. Its described here http://support.microsoft.com/kb/2028504.
I believe I fit into scenario 3 for cause and resolution.
So, it seems that win7 and mixed speed ram may be a problem on some computers ... probably only a tiny number, but it looks like the HP3507 is one of them. I did see somewhere that I could down speed from 667 to 266 which might help with memory compatability but I can't see anywhere on the the insydeH20 bios where to do it. BIOS is version F18 .... upgraded from F15 as part of the Win7/RAM ugrade.
Before I swap back to the 'old' memory I'll see if anybody here can come up with any ideas. It may be that I have to sell off the expensive 2gb memory (ddr2 800mhz 200 pin) for £39.99 from maplin at a bargain price and get 2gb of 667Mhz from somewhere.
The full 'detail' regarding the fault is below.
Bye for now.
Phil
Log Name: SystemSource: Microsoft-Windows-Kernel-Power
Date: 16/01/2011 16:21:31
Event ID: 41
Task Category: (63)
Level: Critical
Keywords: (2)
User: SYSTEM
Computer: (removed by me)
Description:
The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly."
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-Kernel-Power" Guid="{331C3B3A-2005-44C2-AC5E-77220C37D6B4}" />
<EventID>41</EventID>
<Version>2</Version>
<Level>1</Level>
<Task>63</Task>
<Opcode>0</Opcode>
<Keywords>0x8000000000000002</Keywords>
<TimeCreated SystemTime="2011-01-16T16:21:31.187617000Z" />
<EventRecordID>194889</EventRecordID>
<Correlation />
<Execution ProcessID="4" ThreadID="8" />
<Channel>System</Channel>
<Computer>Home_Laptop</Computer>
<Security UserID="S-1-5-18" />
</System>
<EventData>
<Data Name="BugcheckCode">0</Data>
<Data Name="BugcheckParameter1">0x0</Data>
<Data Name="BugcheckParameter2">0x0</Data>
<Data Name="BugcheckParameter3">0x0</Data>
<Data Name="BugcheckParameter4">0x0</Data>
<Data Name="SleepInProgress">false</Data>
<Data Name="PowerButtonTimestamp">0</Data>
</EventData>
</Event>Hi DWeiland and Schwede,
Thanks for your replies. Yes I did the runtime engine registry change and also mass compiled the LV7.1 folder and my sourcecode. I still see the problem as I have set the LV adapter as Lv 7.1.1 runtime engine. Now I have changed it to LV7.1 development system. With this setting, it is not giving any error. Thus I don’t see any problem now. The older version of the code had the adapter as the runtime engine for some reason, now I have changed the setting to the development system. I hope that it shouldn’t be a problem.
Thanks again!
Thank you,
Sasi
Maybe you are looking for
-
I use PS CS6 on a Win7 64bit machine. I noticed several users having issues with the autorecovery in PS. I had some too in the past, and just yesterday I had a PS crashing a couple of times too. The error seemed to be related to the facial recognizin
-
I upgraded to iOS x mavericks on my iMac now i cannot access my iPhoto i get this messageThis update is not available for this Apple ID either because it was bought by a different user or the item was refunded or cancelled. I have not changed anythin
-
Basic Action Script 3 question
I've been watching a tutorial on making a thumbnail photo gallery with Flash. Unfortunately the only tutorial I could find that explained everything step by step was for Flash MX and I'm using Flash CS4. It seems that the scripting code is different.
-
BI - Client copy 000, 001 or neither
After install SAP Netweaver 7.0 BI ABAP+JAVA what shoud we do about client? In BW we can't have more than one client so I think this is the same for BI. If the system start with two clients (000 and 001), should we do a client copy? If yes, which of
-
Problem with new data-sources format
Hi, I m moving to Oracle IAS 10.1.3, so i m testing the application with the standalone version. I use the datasource converter just like the manual say. this is how datasources looks.. <?xml version = '1.0' encoding = 'UTF-8'?> <data-sources> <manag