Dv7-6160ca usb 3 drivers not loading

So I have did a fresh install of windows 7 on this laptop and the whole left side usb is not working and I can't seem to get the usb3 drivers to load. I downloaded many different drivers from the web site and none worked. The laptop is only four days old.
This question was solved.
View Solution.

Hi,
Just to double check, go into Device Manager, right click on either problem device and select Properties. Click the Details tab, choose Hardware Ids from the dropdown box and post back with the details shown under Value.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Similar Messages

Usb hard drive not loading after security update

usb hard drive not loading after security update
I can't seem to find any other posts about this problem.
I have three external hard rives connect by a USB hub to my iMac.
Problem is that if I turn on the hard drive(s) AFTER start up I get a message that the drive either was not recognized by the OS or that it was ejected unexpectedly.
I get the same issue but not all the time if I turn them on before I boot the iMac.
I used the disk drive utility to "repair" the drives but they always come back as "probably ok".
If I restart the iMac with the drives connected (on), it seems to work but not all the time.
A bit annoying as I am wondering if the drives are OK or not.
I don't always need the drives as they are for backing up images from my camera using Apreture.
This all began after i did the latest security update.
is the update to blame?
mahalo.

Yes, you can still use those instructions to reset the PRAM.
You said that you booted to your install disk and that your primary drive did not show up at the Select a Destination screen? That usually means that the computer is either not recognizing your partition, or it's not recognizing the hard drive itself.
Start with this article and follow all the steps even if you already tried them. I suspect that you'll get to step 4 and you'll end up having to call Applecare. If you haven't done those steps, they're most likely going to make you do them anyway, so you might as well get them done before the call.

Microsoft ODBC drivers not loaded??

Hi All:
When I want to import tables to repository then there is error that i facing. Microsoft ODBC drivers not loaded. Can anybody tell why its happens and how can i solve it. Thanks
Ali

Hi,
Please try this first:
FIX: Error "Datetime field overflow" When Inserting Negative (B.C.) Dates with Oracle ODBC Driver
http://support.microsoft.com/kb/250286/en-us
Since it is more related to Access you can ask in office forum or MSDN forum:
http://social.technet.microsoft.com/Forums/office/en-US/home
http://social.msdn.microsoft.com/Forums/office/en-US/home?forum=accessdev
Thank you for understanding.

T61 USB Human Interface Device drivers not loading after undocking

I have a T61 and after I undock (correct method, by pressing the eject button on the docking station and waiting for it to turn green) the laptop from my advanced docking station, the external mouse does not work. More specifically, this is the error message that I can see in the USB Human Interface Device with the yellow ! in Device Manager.
"Windows cannot load the device driver for this hardware because a previous instance of the device driver is still in memory. (Code 38) "
Is there a fix for this? If I reboot the laptop then I can get my external mouse to work because the drivers can load, but I don't want to have to reboot after undocking.

Regarding your keyboard problem, it seems to be a very low-level problem. The driver cannot access the Control Registers on the Keyboard. By going down from your error message to the lowest level, one can see that it's probably a simple "outb" operation (write data on a specified address, shouldn't fail if the address is correct...) that doesn't succeed.
So I think you defintely need to look in your BIOS if you didn't deactivate something when upgrading, or messed with some address space, or many things I cannot think of right now.
Good luck

W7/64 USB Drivers not loading on boot-up

Installed W7/64 onto clean SSD with all ThinkPad items added and updated off the Driver Matrix (W500).
Using with 2503 Dock I have up to 13 USB devices attached .. just like in former WXP-SP3 setup.
Now when I start the system, only my Logitech LASER mouse (with USB transceiver) driver loads ... ALL others have yellow flag (not loaded). Strange is that this even affects my expansion slots ... that don't register until USB flagged drivers are manually updated.
Further I looked in the windows/system32/drivers folder and none of the several USB driver files are present.
Is there a way to repair this situation without the agony of reinstalling everything.
Please, advise.

csc4096 wrote:
OS X Lion on a Mac Mini with Microsoft Intellimouse
Installation worked with no errors but now when I boot up the mouse cursor is at the top left of the screen and refuses to work until I manually unplug it and push it back in again. Annoying to say the least.
Have you tried another mouse? Have you tried a different USB port? If the mouse is plugged into a hub, have you tried plugging directly into the Mac?
Also the scroll-reversal option is missing from the relevant control panel.
Any sensible suggestions?
To confirm, can you screen shot the Mouse System Preference?
If all else fails, you can install Scroll Reverser. It was for Lion developers to get accustomed to the Lion-style scrolling before Lion was released, but it works just fine in Lion for these unusual situations. (e.g.: older Macbook Pro without a multitouch trackpad.)

Lumia 625 mtp usb driver will not load

After latest firmware update I can not load or reload this driver. Windows 7 PC will not recognise fhe phone. Usb knows it is a 625, but unable to do anything with explorer or the Windows Phone for desktop

fergiefred20, which app do you use? The Nokia Suite does not support Windows Phone.

HP Pavilion dv7-6c95dx USB 3.0 Not Working

As stated in the title my 2 usb 3.0 ports on the left side of my computer do not work. I downloaded the hp support assistant and it didn't find any drivers I was missing, searched online etc and couldn't find an answer. Any help would be appreciated!

Hi,
Please try the first driver of the following link:
https://downloadcenter.intel.com/product/65855/Intel-USB-3-0-eXtensible-Host-Controller-Driver
If your machine is older, please use the second one
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Xorg.conf nvdia drivers not loading?

Hello i am trying to configure X with a fresh install of Arch. (First Time)
And i installed the Nvidia driver
pacman -S nvidia
And i ran
Xorg -configure
And got an error saying kernel module unable to load and a few output errors, i am unable to paste them so here are the 2 logs for Xorg.conf and kernel log just in case.
Kernel.log
http://pastebin.ca/1581935
Xorg log
http://pastebin.ca/1581938
Im almost there. Just hoping i can get this working well.
Oh and this might help for future editing my monitor is a Samsung SyncMaster
http://www.samsung.com/ca/consumer/deta … AQWJFV/XAA
Just thought id paste it just in case i need to know anything for editing xorg.
Thanks for any help much appreciated.

from your kernel.log:
Sep 27 17:37:08 withteeth kernel: NVRM: The NVIDIA Quadro4 980 XGL GPU installed in this system is
Sep 27 17:37:08 withteeth kernel: NVRM: supported through the NVIDIA 96.43.xx Legacy drivers. Please
Sep 27 17:37:08 withteeth kernel: NVRM: visit http://www.nvidia.com/object/unix.html for more
Sep 27 17:37:08 withteeth kernel: NVRM: information. The 185.18.36 NVIDIA driver will ignore
Sep 27 17:37:08 withteeth kernel: NVRM: this GPU. Continuing probe...
Sep 27 17:37:08 withteeth kernel: NVRM: No NVIDIA graphics adapter found!

X-FI xtrememusic drivers not loading problem - having to reinstall drivers every other reb

I am having a bizarre problem with my xtrememusic card. Latest drivers and all, the motherboard is a gigabyte GA-965P-DQ6 (rev .0). Basically, I install the drivers and reboot, the card works fine. I reboot, it stops working, gives me a "can't load drivers" error. Rebooting doesn't change this. Reinstall the drivers again (which requires a reboot) and it works, until I reboot, etc.
Any ideas? Very frustrating. This is a new install of XP/SP3 - but before I rebuilt the computer I had the same setup (hardware/OS) and it worked fine, no hardware changes.

I had the same problem, also with a Gigabyte board. Try to remove all other PCI Cards ...
Does it work?
Maybe you can than add one after the other.
For me it looks like, that the board or windows does randomly change the IRQ's and Memory Spaces ..
I got the same problem also with my PCI TV Card ...so it doesn't looks like a X-Fi only Problem.
Don't know why.
Greetings

HP Pavilion dv7-6166nr USB 3.0 Not Working

My two left USB 3.0 ports aren't working. In the Device Manager it doesn't find the drivers for them. I've searched the forums, tried other drivers, tried the drivers for the latest Renesas USB 3.0 Host Controller drivers and those don't work either. None of the drivers I download seem to work including the ones listed for my laptop on the HP.com support website.
Any help would be great, thank you.
I've also tried: USB3.0_allOS_2.1.28.1_PV.exe with no luck.
This question was solved.
View Solution.

Hi:
Install the AMD chipset drivers and reboot. You want the first file listed on the webpage.
http://support.amd.com/en-us/download/chipset?os=Windows%207%20-%2064

T530 with 2 display adapters - NVIDIA NVS 5400M and Intel HD Graphics 4000 Drivers not loading

Both the Nvidia and Intel graphic drivers show in device manager that they have problem and can't load properly. I have tried uninstalling both they both reinstalled on a reboot with same issues. Is this hardware or corrupt drivers?? Or?

Failure progressed to a point where I could login remotely (GoToAssist) and see the screen but the LCD and External Monitor both were black.
Called tech support, they dispatched a tech (after 3 days, and a bunch of phone calls). They replaced the system board and display board? same problem. Their answer was I needed to reimage the machine.
I found out that Windows had done an update. We did a system restore to before the update (30 some updates) and restored the local displays.
BUT....both the NVidia and Intel HP Graphics devices in Device Manager indicate problems. And this was after reinstalling the video drivers I pulled down from Lenovo.
Any thoughts on where I go next?? Lenovo has washed their hands of this problem....
I am about to wash my hands of Lenovo as a vendor for PCs.
Larry

Renesas usb 3 drivers, not on website, or cd

Hello!
Motherboard: a78m-e45
anybody know why MSI doesn't have USB 3.0 drivers for the onboard ports anywhere? I found some by using the device id, but they were xp 64bit, got those to work, but would rather MSI support their own board and have the drivers available. Unless I am missing something.
Thanks

I have checked the board page and there is no word on the Renesas.
I have also took a look on the picture of the board , failed to see the Renesas USB 3.0 chipset.
Are you sure this is the board you are having ?
Are you sure there is a Renesas chip there ?!
What CPU are you using ?
What operating system are you using ?!

Fglrx drivers not loading after update to Kernel 3.7.3

Hi,
I just updated to kernel 3.7.3 and the fglrx module isnt loading. I just read the catalyst wiki page again and I didnt install the catalyst-hook package or add fglrx to /etc/mkinitcpio.conf hooks array.
Not sure what todo?
Thanks.

nirvanix wrote:I just reinstalled the catalyst-dkms package and then it worked again.
Excellent thanks. I didnt want to go messing around and screwing it up but that was simple enough. I also installed the catalyst-hook package and linux-headers for next time. Hopefully wont be a problem.
Thanks.

Drivers not loading on Windows XP for ENET-485.

I'm no dummy or I wouldnt have gotten this fare. Checking "device manager" and the "diagnostic utility" I cant seem to get my newly purchased NI-485 to work on my Windows XP machine for lack of recongnized drivers. I cant even fine the ".inf" file myself. Any ideas? Software package loaded just fine, several times.

Thanks for the kind reply. However I still have the problem, after a few weeks of hacking at I seem to understand what the problem is but I cant seem to fix it. I see it with the diagnostic utility, as it if fails identify the right ports, and I can see the ports assigned in the device manager, but the devices are failing to actually connect as a com port. Ie any programs cannot see the actual com port as the device mananger has them assigned. I've tried this on two different computers now,two different OS's same results. I'm convinced it's something I'm doing wrong on the set up.

[SOLVED]Virtualbox drivers not loaded at startup

I followed the wiki and added vboxdrv to my DAEMONS. The only change is that I start it in the background. However, when I start Virtualbox, and then the guest OS within, it gives me an error.
DAEMONS=(syslog-ng @net-profiles @dbus !sshd !netfs @crond @alsa @acpid @ntpd @vboxdrv)
I have to manually
modprobe vboxdrv
in order to start the guest OS. How can I have the vboxdrv started at boot?
also, is there a way to start the guest OS directly, without having to start the Virtualbox console?

Inittab:
# Runlevel 5 starts X environments
x1:5:once:/bin/su work -l -c "/usr/bin/startx -- :11 vt11 > /dev/null 2>&1"
x2:5:once:/bin/su windows -l -c "/usr/bin/startx -- :10 vt10 > /dev/null 2>&1"
x3:5:once:/bin/su windows -l -c "/usr/bin/VBoxManage startvm Ama --type vrdp > /dev/null 2>&1"
The first two start new X sessions, user "work" on vt11 and user "windows" on vt10. The third starts an RDP headless VirtualBox VM as user "windows". When the two X sessions start, they execute ~/.xinitrc (each of ~work/.xinitrc and ~windows/.xinitrc):
#!/bin/sh
# ~/.xinitrc
# Executed by startx
VirtualBox
This starts the VirtualBox GUI so I then switch to vt11 or vt10 and select a VM to run. Note each of ~windows/.VirtualBox and ~work/.VirtualBox are completely separate VB configs owned by the separate accounts.
Note that I don't bother with a window manager because I run the VMs full screen anyway, but you can start one if you want within .xinitrc.
You can change "VirtualBox" in .xinitrc to start a specific VM using VBoxManage startvm "MyVMName"
Hope this helps.
Last edited by starfry (2011-03-29 21:49:33)

Dv7-6160ca usb 3 drivers not loading

Similar Messages

Maybe you are looking for