Dv7--6b57nr attempting use recovery disks after virus. Recovery disks fail to load

I am attempting to load the recovery disks for Windows 7 Home Premium. Had a few virus's and the recovery disk installs fails. Have checked the disk within the Bios. The error is as follows: The Recovery attempt has faild. Select one of the following buttons: Save Log; Details; Retry. I don't see any specific errors besides the Recovery attempt has failed. What is the next step that Ineed to do. I have the saved log file HP_SSRD_LOG.SRD.
I have a Serial # of 2CE1480BIX and a product ID of AIT85UA#ABA.
I have attempted to reload after I blanked out the whole drive. That was the only what to get rid of the viruses of the system. I am a tech working for the owner Waymon. Please assist me or tell me exactly what I need to do to get this problem resolved and get the system loaded. Thanks.
Gets to he HP Software Installation now on the five installation try. It then reboots and tries to reload the system.   Here is the error { The Recovery Attempt Failed. Select on eof the Following Buttons:
Save Log ; Details ; Retry.
Here is the file from the Details button. CTOERROR.FLG.txt
[12:53:08.53] Entering Checking OS Edition...
[12:53:08.53] Check RStone.ini file to determine the requried edition.
[12:53:08.58] Exiting Checking OS Edition...
[12:53:08.60] Check if Upgrading Win 7 is required.
[12:53:08.61] Current Edition is [HomeBasic]...
[12:53:08.63] Required [Starter]. Don't need to upgrade...
[12:53:08.63] Required [Starter] ...
[12:53:13.28] Required [Starter] Edition. But, OS is not [Starter]...
[12:53:13.28] Upgrading OS edition might have some problem...
Deployment Image Servicing and Management tool
Version: 6.1.7600.16385
Image Version: 6.1.7601.17514
Current edition is:
Current Edition : HomeBasic
The operation completed successfully.
Component: TDC Preinstall Diagnostic Tools for Windows 7 - TDC
Error found: No OS Flag set on unit, please use EEPROM to set ~OS SKU~ value = 2
[12:54:04.13] ------------------------------------------------------------------------------------------
***CTO Error condition has been dtected in [Factory Update] phase !! ***
[12:54:04.15] Suggest to create PIN-log and send to TWN PDC NB-PreinPM for further analysis ...
[12:54:04.15] ------------------------------------------------------------------------------------------
[12:52:11.75] Start BBOffline.cmd...
UPDrv=[C:]
[12:52:11.77] Set UIA Error Code to 951
[12:52:12.08] WinPE is 32bit.
[12:52:12.08] Starts [FixUps].
[12:52:12.09] ---------------------------------------------------------------------
[12:52:12.09] FixUps.cmd...
[12:52:12.09] create overall progress info...
[12:52:13.72] FixUps.cmd completed...
[12:52:13.72] ---------------------------------------------------------------------
[12:52:13.72] Starts [Tweaks for SSRD].
[12:52:13.75] ---------------------------------------------------------------------
[12:52:13.75] SSRD Tweaks to change user default locale...
[12:52:13.75] Copy C:\System.sav\Util\TDC\MCPP\FBIRES\FBIUSRES.DLL.
[12:52:13.86] Run "Dism.exe /image:C:\ /Set-SKUIntlDefaults:en-US -image:C:".
[12:52:21.38] ---------------------------------------------------------------------
[12:52:21.38] Launch PININST.exe for Offline ...
[12:52:33.37] Starts [Sleep 10 sec].
[12:52:43.43] Starts [Create RStoneFUpdate.INI].
[12:52:56.48] Starts [create 1GB Pagefile for offline].
Volume in drive C has no label.
Volume Serial Number is 9EEF-EDFF
Directory of C:\system.sav\bbv
11/23/2013 12:52 PM     1,073,741,824 pagefile.sys
               1 File(s) 1,073,741,824 bytes
               0 Dir(s) 44,736,716,800 bytes free
[12:52:56.57] Brand detection.
[12:52:56.87] ---------------------------------------------------------------------
[12:53:43.17] Start SysID Check...
[12:53:43.62] Start Option Code Checks...
SKU_DEF_COUNTRY=[244]
SKU_DEF_SYS_LOC=[en-US]
Reset country in administrator...
Reset country in Default user...
Reset System localed
Deployment Image Servicing and Management tool
Version: 6.1.7600.16385
Image Version: 6.1.7601.17514
Reporting offline international settings.
Default system UI language : en-US
System locale : en-US
Default time zone : Pacific Standard Time
User locale for default user : en-US
Location : United States (GEOID = 244)
Active keyboard(s) : 0409:00000409
Keyboard layered driver : PC/AT Enhanced Keyboard (101/102-Key)
Installed language(s): en-US
Type : Fully localized language.
The operation completed successfully.
Updated System Locale info..
[12:53:59.16] Start PIN Tweaks...
[12:53:59.20] ---------------------------------------------------------------------
[12:53:59.20] PIN Tweaks to hide All for BurnBoot BBV and BBV2 on restored image...
[12:53:59.20] ----------------------------------------
[12:53:59.20] Tweaks for OOBE's Unattend.xml
[12:53:59.20] to pick up the proper file...
[12:53:59.20] ----------------------------------------
[12:53:59.20] rename unattend.org to unattend.or_
[12:53:59.25] ----------------------------------------
[12:53:59.25] without Light Sensor..
[12:53:59.25] ----------------------------------------
[12:53:59.27] This is Restored image by SSRD [SSRD.flg]...
[12:53:59.28] ---------------------------------------------------------------------
[12:53:59.31] Start MIR Tweaks...
[12:53:59.34] ---------------------------------------------------------------------
[12:53:59.34] [MIR Tweaks] ...
[12:53:59.36] ---------------------------------------------------------------------
[12:53:59.39] Start Factory Update(s)...
[12:54:01.28] Start QFE Offline installation...
[12:54:03.96] PININST_OFF: PASSED...
[12:54:03.99] Type C:\System.sav\Logs\BBFindEr.log...
[12:54:04.01] Type C:\System.sav\Logs\BBFindE0.log...
---------- C:\SYSTEM.SAV\LOGS\PININST_OFF.LOG
Result=PASSED
[12:54:04.04] Type C:\System.sav\Logs\BBFindEr.log...
[12:54:04.05] Type C:\System.sav\Logs\BBFindE0.log...
---------- C:\SYSTEM.SAV\LOGS\BBFIND4QFE.LOG
[12:54:04.05] Check FUList.log if there is duplicate Desc...
No duplication.
[12:54:04.13] No Duplicated Desc is found... PASSED.
[12:54:04.13] There was no Factory Update...
I also have to HP_SSRD_LOG.SRD file. What Do I need to do now? Thanks.

Recovery Discs failure is frequent, and unfortunately has many causes. Some things to try that have worked in other cases.>>
1-Enter BIOS and reset to Default settings. Usually it is F9 key,check bottom of screen to be sure. Next F10 to Safe & Exit. Run Recovery again.You can attempt it from the partition now instead of Discs if preferred by tapping away at the F11 key at start up.
2-Scroll down on the page and get> Bootable CD ISO and> ImgBurn to burn the iso image to cd-a guide on using ImgBurn to write an ISO to a disc is Here. Once created, boot from it. Delete any hdd partitions, create one and format. Next try booting from Recovery Discs again.
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others**

Similar Messages

After Effects CC 2014 fails to load Quicktime Components.

After Effects CC 2014 fails to load Quicktime Components and unable to export or render .mov, .mp4 or any type of quicktime videos.
The application will launch and I can create and edit projects and comps but I am unable to render any type of movie files. I can render images sequences.
I have the latest version of Quicktime (10.3) and Quicktime Pro 7. Please let me know what I need to do to get AE CC 2014 to render movies.
Thank you.

Kevin,
I’ve reinstalled Adobe AfterEffects CC (version 12.2.1.5) and am still having the same issue with the failure to recognize Quicktime.
Can you assist?
John Luu
Art Director / Digital Marketer
1702 Washington Avenue
Houston, Texas 77007
Tel: 713-523-5711 ext. 208
Fax: 713-523-6083
[email protected]
www.axiom.us.com

Can't boot after update, getting "microcode: failed to load" error

After restarting my computer, it's no longer able to boot, and just prints a continuous stream of errors. The first error it gives is "microcode: failed to load", and I looked it up and found that I should just have to install amd-ucode. Easy enough, except I can't boot. I tried booting into the latest live-usb image, and after connecting to the internet, mounting the partition to /mnt, and running
# arch-chroot /mnt pacman -S amd-ucode
I get the following error
error: amd-ucode: signature from "Allan McRae <[email protected]>" is invalid
error: failed to commit transaction (invalid or corrupted package (PGP signature))
Errors occurred, no packages were upgraded.
I'm not very familiar with how chrooting works, especially not arch-chroot, so I don't trust myself to fix the problem without breaking something. I was thinking of just putting the package on a flashdrive and installing it with
# arch-chroot /mnt pacman -U amd-ucode-package-name
Should I do it this way or am I misunderstanding how arch-chroot works?
By the way, this is an issue with my desktop. startx stopped working on my laptop right before I went to use my desktop and rebooted it, so after this issue is fixed I'll be making another thread about my laptop >_> Any help is much appreciated.

Ok, so I managed to install amd-ucode with pacstrap. That got rid of the microcode error, but I'm still getting
/dev/sdc1 contains a filesystem with errors. Forcing check
And then it just repeats the error message
[60.50342] ata5.00: failed command: READ FPDMA QUEUED
[60.51345] ata5.00: cmd 60/<long number that's formatted similarly to a MAC address>/40 tag 0 ncq 131072 in
[60.51743] res 40/<the same number>/40 Emask 0x10 (ATA bus error)
[60.62421] ata5.00: status: { DRDY }
The numbers on the left just keep counting up, but the repeating error message stays mostly the same. What's odd about this error is that the disc it says it has a problem with isn't even the disc with the OS on it. When I have time I'm going to try physically removing /dev/sdc from my computer to see if the error stops.
Oh and there won't be any thread about my laptop issues. Turns out I filled my whole HDD, which was causing startx to fail.

Using recovery discs after virus

I have a Toshiba Satellite P775-S7100. I got a virus on it last night and took it to Best Buy. They said that I could use my recovery discs to repair it. I have 5 recovery discs. I put the first one in and let it do its thing, but then it didn't ask for the other 4 discs. Is that because I was only reinstalling the OS (Windows 7)?

It's common for it sometimes not need the last disc, but I've never heard of it only needing the first disc. However, was the recovery successful?
- Peter

Can't write to external disk after cloning startup disk to it

After cloning my PowerBook Pro's startup disk to an external Thunderbolt drive, and temporarily using that drive to boot-up, the Thunderbolt drive is locked into Read Only mode. How do I enable it to write again? The INFO pane says the following: System privilege: "Read & Write"; wheel: "Read Only"; everyone: "Read Only". The basis for my cloning was to deal with a very full startup disk that I did a lot of video editing on (very processor intensive). The disk had become fragmented to the point that it couldn't access sectors fast enough for editing, so I cloned it over to a G-Tech Thunderbolt drive (using Carbon Copy Cloner), reformatted the MacBook startup disk, then reverse-cloned the copied files back over from the Thunderbolt, the idea being that they'd be re-written nice 'n neat in unfragmented order into their proper sectors. I then ceased booting-up from Thunderbolt, but now the system seems to think that Thunderbolt is still special in some way like a gossling bonded to a surrogate human mother, and it won't let me write to it. Can anybody help me with this?

Have you verified and if necessary, repaired the disk(s) using Disk Utility on your Mac?

My system software has crashed, and I am hoping to use an apple certified data recovery specialist in Atlanta. Who can I use and still have my warranty coverage after attempting to recover the data?

My system software has crashed, and I am hoping to use an apple certified data recovery specialist in Atlanta. Who can I use and still have my warranty coverage after attempting to recover the data?

Contact the nearest Apple store for a definitive answer. We are users like you and cannot provide you with an accurate answer.
Ciao.

HP G56 System Recovery Problem after removing disk 4 black screen

hi everyone
this is my first time, im helping my nextdoor neighbours laptop hp g56,
the hard drive has been fried and i have intalled my old playstation 3 40 gb hard drive into it.
after the recovery system finished and told me to remove disk 4 it restarts and now have a black screen, does this mean its still installing because i turned it off and then on and now say no bootbale device.
windows 7
40 gb hard drive (ps3 40gb)

pepe999 wrote:
selinacartwrigh wrote:
my system comes on and then stop before it opens the key board and say disk boot failure insert system disk how could find a disk I cant even get in
The message means that your internal hard has been damaged. This message always comes up when the file system is corrupted. I suggest to remove it, connect the hard drive into a different computer as an external drive (use usb caddy), perform a backup if possible and the format the hard drive and restore the factory settings. I'm afraid that you have to reformat the hard drive, a checkdisk scan won't help..
The error message means that the Boot Sector is corrupt or has been damaged. It does not mean that the hard disk is damaged.
This is a fixable issue. There are a few command line tools that can be used.
You will need to make an appropriate version (32-bit / 64-bit) of the Windows 7 repair disc from a working Windows 7 installation. You will need either a USB or CD to create your rapair CD/USB. Follow the instructions on this video to create the repair installation of your choice..You will will be using the manual boot sector repair that is described in this video to repair your Windows 7 Boot sector. Use the Windows 7 repair disc or repair USB thumb drive that you created earlier to accomplish the repair.
Best regards,
erico
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

After a recovery reinstall of 10.8.5, using Safari 6.0.3, I get the message "Safari won't open because of a problem"

After a recovery reinstall of 10.8.5 and using Safari 6.0.3, I get the message "Safari won't open because of a problem"
I'm not sure if this Safari is compatible. I also have Safari 7.0.4 in my applications folder, which i downloaded as an attempt to
solve the problem, but it isn't compatible with my system.

Having two copies of Safari on the hard drive is what's keeping Safari from opening.
Move the 7.0.4 version to the Trash.
Then restart your Mac and try Safari.
Safari 7.0.4 won't run on Mountain Lion. Only v10.9 Mavericks.

Using Disk Utility From Recovery Partition

Is there an advantage to repairing permissions after booting into Recovery disk? (Hold Option key as restart) I realize that Repair disk will be available if needed & it is not available when using Disk Utility from Mac HD partition.

Thanks!
I thought that was the case but I had read multiple accounts of people with slow Macs after upgrading to Mavericks, running repair disk permissions from recovery disk to fix the problem. I wondered why not just run repair permissions w/o restarting into recovery disk. Then they can also run verify disk, if they wish & only if there is a problem with the disk would they need to boot to recovery disk in order to run repair disk.

Satellite A200 - can't use Vista after Product Recovery

Hello. I hope someone can help me with the following... This week I've had various issues with my laptop following a Vista update that System Restore did not fix, so I decided to go for a full Product Recovery (as I have a full backup of all my files).
So far I have used product recovery on my laptop in each of the 3 ways I can see (and more than once): without changing settings, changing settings and maximising the partition, changing settings and selecting the advance / expert option.
Each time I was able to complete the initialisation of windows, creating a new user account, etc. Once the desktop has been set up, I get a small window with a progress bar and when this completes I click the 'restart' button...
After restarting I get to the black screen that says Microsoft Corporation with the green progress bar, but it stays there for what feels like 'too long'. After a while I get a black screen with a cursor and then a blue screen for a crash dump.
If I use F8 and start in Safe Mode, the system stops at the CplIR.sys file, although hard disk activity seems to continue. After 10+ minutes I switch off.
If I use F8 and then select Repair Computer... this is what happens with each option
- Restore the complete windows operating system: after clicking OK nothing happens.
- Memory diagnostics: there are no problems with the memory
- DOS prompt: I have run CHKDSK and there are no problems with the hard drive
- Startup Repair: there are no errors,although the diagnostics say 'failed' when it sees there are no system restore points
Then on restarting I either get the black screen with cursor followed by the crash dump OR if I manage to sign in and get to my desktop, I get the crash dump as soon as I try to do something (like open the control panel).
Following instructions found elsewhere, I've tried this after removing the battery and then changing the power management options immediately after windows initialisation (ie. before clicking the restart button). No change.
I've even ignored the restart button! But still get a crash dump when I try to do something.
Any ideas?? I have spent (ie. wasted) so much time on this and don't understand what can be wrong after formatting the drive and re-loading windows image...

Hello
It is very interesting story. I have recovered several notebooks many times but I have never noticed something like this.
I must say that all you have done right and you think in right way. If I were you I would try exactly the same steps to get it work somehow.
I don't know which various issues you had before but I presume there issues were just software issues and not relevant for hardware functionality.
It is really hard to say what the problem can be. What you can try is obtain somewhere Microsoft Vista installations disc and install naked Vista to see if the same will happen again.
Anyway, the fact is that recovery images are tested and adapted for each notebook model and if the hardware is OK there is no reason for such behaviour.
Try with clean installation using Microsoft installations disc and let us know what happen exactly.

Boot Camp will not work after installing recovery disk

I purchased a refurbished Macbook Pro 2012. I went ahead and installed dual ssds and used the Mac OS X recovery disk from USB flash drive. I wanted to install WIndows 7 through bootcamp. Bootcamp will not start after selecting continue. I'm not sure if boot camp is corrupted or something I did wrong.

Well you'll need to see if that remote app has an update or if it is compatible with IOS 7.
since you didn't state which remote app your using.

How to recover the recovery partition after delete all hard disk partitions

hallo
how to recover the recovery partition after delete all hard disk partitions in toshiba satellite pro c850-1fn ?
note that : I did not work recovery disc or usb to my laptop.
I have need of your help.

Satellite Pro C850-1FN (PSCBXE-01700EEN)
Restore the hard disk to its original out-of-the-box contents using Toshiba recovery media. All of the original partitions will be restored, including the recovery partition.
If no recovery discs were created, you can obtain them from Toshiba.
Toshiba Europe Backup Media Online Shop
For instructions, see the section Restoring the pre-installed software from your created Recovery Media on p. 4-18 of the User's Manual (attached).
-Jerry

HT4623 I trying to update my iPad using iTunes. After connecting to MacBook Pro where is installed all latest software iPad is recognised as iPad, Serial Number: n/a. iTunes run recovery mode, trying to restore iPad firmware, and in the end unknown error

There was some updayts for my iPad 4 automatically downloaded. After installing it, the iPad began to restart itself every few minutes.
I tryed to update my iPad using iTunes. After connecting to MacBook Pro, where is installed all latest software, iPad is recognised as "iPad", Serial Number: n/a. iTunes run recovery mode, trying to restore iPad firmware, and in the end unknown error occured (3). Tried many times, not results. And now iPad stays only in recovery mode, can't switch it off. How can I solve this problem please?

When I restart my iPad the connect to iTunes comes up and stays on until it shuts down again, I have read a report from Apple support suggesting I reinstall iTunes so I might try that again and also your suggestion which i shall also try, but thanks again - rg1547

2106f Error Code after Internet Recovery Attempt

Anyone ever get a 2106f Error Code after Internet Recovery Attempt? What next?
Background: Macbook Pro (late 2011) shows startup progress bar, goes ~ 1/10th of distance, freezes, then goes black after ~2min. Did this:
1. Clean startup attempt (shift)
2. Zapped PRAM (option command P R)
3. Reset SMC, Startup
4. Attempted Internet Recovery process (Cmd R) over ethernet connection, but after several hours, got the -2106F error.
MacBook Pro 2.2 i7 Late 2011

How long were you able to watch this movie before it crashed?
Now is it everytime you boot up, you get the BSOD 0xc0000001 ?
Can you start up in SAFE MODE?
"Knowledge should be unrestricted and the most important commodity we can offer to help one another."

After ejecting a disk plugged into the USB port using Finder, I am now getting "The disk was not properly ejected" message. This didn't used to happen. How can this be corrected?

After ejecting a disk plugged into the USB port using Finder, I am now getting "The disk was not properly ejected" message. This didn't used to happen. How can this be corrected?

When you right (control) click on the disk and click eject "disk name", do you pull it immeadiatly or wait a few seconds for it to unmount? Try waiting and see if you get the same message. If you do, when the disk is connected go to applications/utilities/disk utility, after opening DU, select the volume in question from the left side bar and try a permissions repair, you may also run verify disk and see if it comes up with any errors (they will be in red)

Dv7--6b57nr attempting use recovery disks after virus. Recovery disks fail to load

Similar Messages

Maybe you are looking for