DV7 - Error 03F0 - No Boot Device Detected - Passes both Memory and HDD Test

Hi there,
My DV7 will not boot up at all. When powered on, I see the HP loading screen briefly, then into "dos type" font saying "No Boot Device Detected - Error 03F0"
I have run both the memory test and hard drive test from the diagnostic menu and both come back ok.
A little more history on the Device/Problem;
2 months ago it was shutting itself off due to overheating - After a good cleaning, the temps cooled down enough that it was no longer shutting off.
I am currently in India, plugging directly into outlets (230v power) using an adapter. 10 days ago there was a small spark at the outlet leaving a very small spot on one of the prongs of the adapter. There was no power flicker, and it wasn't a surge, just almost like a bad connection sparking. This "spark" seemed to have killed my charger immediately. I used the battery until nearly dead, purchased a new charger, but when I returned and tried the new charger, it would not charge, nor power on. When plugged in, at this point, the power/charging light on the side was lit, but not on the front. I used a pin to open the CD drive, and the front light lit up, but it still would not power on.
I took it to a repair shop here in India, and they managed to get it so it would power on (not sure how), but that has only brought me to where I'm at right now with the Error. They said "It worked, and then we tested again and it didn't work and now it no work".
My current BIOS edition is F.46.
Essentially I'm wondering if I'm screwed - and if I'm not, then what can I do to trouble shoot/fix it?
P.S. Finding parts in India that are specific to my computer will be near impossible with the technology differences. Also, dealing with local techs is extremely difficult so I'll need to know
P.S.S. I just tried to power it on again to double check the accuracy of my post and it will not power on, nor can I get the CD drive open again....

Is the unit still in warranty?
Based on the description of the behavior, it does sound a hardware issue beyond the hard drive.
Was the AC adapter that was purchased an HP adapter? I know you said it is difficult to get the right parts in your area, but I want to confirm if it is an HP adapter or aftermarket.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Similar Messages

Can't detect boot device after factory format to new HDD

First off, I have an HP Pavilion G6 that I purchased in December 2012. Yesterday I decided to get a new HDD to upgrade it and start fresh. It's a 1TB SSD+HDD hybrid by Seagate. It installed without a hitch, and I used my HP recovery CDs to do a factory format of the disk.
It finishes, reboots, but instead of rebooting to the HP Windows 8 setup screens, it goes to what looks like Windows 8 safe mode with a box containing the date, time, and it says something along the lines of "HP diagnostics driver installation" with an OK. Clicking that or not makes it disappear, and there's a command prompt bar at the bottom left hand corner of the screen.
The screen changes to an HP screen that begins to install drivers. It finishes, and reboots to a black screen that says "no boot device detected, please install OS."
I ran a check of the drive and it's fine. I swapped my regular drive back in, and it loaded up fine. In fact that's what I'm using right now to type this.
What could be the problem here? The boot order was never changed in the BIOs. If it were the connector failing I doubt it would load the drive that's always been in the computer. Loading up the newly formatted drive in an external enclosure shows that Windows 8 is indeed on it, but on a 93GB partition even though the drive is 1TB.
I'm at a total dead end here and no one seems to know what to do!
This question was solved.
View Solution.

Hello @kylemcauliffe15,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how your notebook is displaying an error message that your new SSD is not detected as a bootable device after a factory format. I would be happy to help you, but first I would encourage you to post your product number for your computer. Below is a is an HP Support document that will demonstrate how to find your computer's product number. In addition, it will also help if you indicate which operating system you are using; and whether your operating system is 32 or 64 bit. The more information you can provide, the better!
How Do I Find My Model Number or Product Number?
Which Windows operating system am I running?
Is the Windows Version on My Computer 32-bit or 64-bit?
Please re-post with the necessary information, this way I will be able to research this further for you. I look forward to your reply!
Cheers!
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Getting an error 'Cannot open Boot device' while trying to install Solaris

Hi,
We were trying to install Solaris * on a Sun Sparc system and the CD rom drive does not seem to get recognised. When we try booting from cd rom we get an error 'Cannot open boot device' .
This server was up & running and we were trying to remove a hard disk that had failed and modified the vfstab script . After that the system failed to even boot up. So when we tried reinstalling the OS we are running into this problem.
Am new to this technology ...And any help would be greatly appreciated. .....
Thanks

Cdrom drive must be scsi device 6
I assume you are running < boot cdrom> at the ok prompt
also at the ok prompt run the command <probe-scsi> (without the angled brackets) you need to see the following:
Target 6
Unit 0 Removable read only device TOSHIBA XM.......bigpileofnumbers
If not, check the cdrom drive and the cdrom inside
hope this helps
Alan

HT5706 I just purchased an AppleTV and am trying to connect AirPlay with my mac (2012 model) In 'system preferences displays' an airplay menu is listed but it says 'no device detected'. My AppleTV and macbook are connected to the same network. Any help?

I just purchased an AppleTV and am trying to connect AirPlay with my mac (2012 model) In 'system preferences > displays' an airplay menu is listed but it says 'no device detected'. My AppleTV and macbook are connected to the same network. Any suggestions why it is not working?

Troubleshoot the network as that is likely what is causing the issue.
Also, temporarily disable the firewall on the Mac and disable IPV6 on the computer.

HP DV7-1245DX Sees no boot devices

I have a HP DV7-1245DX Notebook computer. It was running slow, so went to reset it, and it came up with the error "03F0" which then says "No boot device present, Install operating system".
Thinking the hard drive had died or got corrupted but this code continued when the hard drive had been removed, and the system would find no other boot devices. I tried bootable cd's, dvd's and a bootable USB stick that I know works, and the system does not see any.
The odd thing is it CAN run a disk scan on the hard drive when its plugged in. It just does not see it in the boot manager. The boot manager is actually blank, showing no options for devices. I setup the boot order properly, and made sure "cd drive" was enabled as a boot device, but this changed nothing. I tried bios defaults also.
I removed the memory, tested each individually, unplugged the power and cmos and put everything back in, plugged in another hard drive with a different windows install, nothing changes the error.
I put the original hard drive in an enclosure and ran a MBR rebuild on it with EASEUS, and a disk scan which returned no errors, the system still could not boot to the device.
The only thing I can think at this point is that the disk controller went bad, or the BIOS is corrupted. Since this system sees absolutely NO boot devices I don't have an idea on how to reflash the bios.
Thanks for your responses

Hi,
I would tend to agree with your conclusion that the sata controller has failed ( usually, a bad bios is more obvious as the notebook will not POST ).
If you look in the Bios Menu, does it recognise any bootable devices available?
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Atheros ar5b95 generates 104 Error: incompatible wireless device detected

The intel wireless card failed in CQ61 - 425SA. So i ordered an Atheros AR5B95 that is listed as compatible here at the HP site and at the manufacturer's site.
Unfortunately, the machine won't boot with the card inserted, generating error message 104: Incompatible Wireless Device Detected.
I had a look at the BIOS but it's up to date (F.23) and there appears to be no place in the setup menu where I can indicate a different wireless card. I tried installing new drivers but, of course, if the machine won't book I can't install the drivers for the card.
The card is imprinted with the AR5B95 identity and Atheros branding, so I presume it's genuine.
Any help would be greatly appreciated.

hp implement whitelisting of wifi cards in BIOS, your original intel would of had hp part number that matched with allowed numbers in the BIOS thus boot without 104 error > your current atheros is a generic atheros card & the BIOS sees no matching part number so flags 104 error.
You have 2 choices, 1: buy a correct hp branded card that is supported by your BIOS , 2: install a no whitelist BIOS so you can use any wireless card .
No whitelist bios link below >
http://www.bios-mods.com/BIOS/index.php?dir=Whitelists%2F&download=sp51527_NWL_EISTUlk_MoreOptions_B...
You may need tape pin 20 on the atheros card with some scotch tape & use windows 7 mobility centre to toggle wifi on/off
Like my post? Click Kudos (thumb+) to show appreciation.

DB Function errors out when trying to use in both Answers and RPD file.

Hi All,
Its a strange behaviour that one function which is in Database works fine the other does not. I have created 2 DB functions and accessing them from OBIEE in both Answers and RPD. One function which returns a Date is working fine, the one which is returning a number is throwing a error.
State: HY000. Code: 10058. [NQODBC] [SQL_STATE: HY000] [nQSError: 10058] A general error has occurred. [nQSError: 16001] ODBC error state: S0022 code: 904 message: [Oracle][ODBC][Ora]ORA-00904: "APPS"."XXX_BUSINESS_DAYS": invalid identifier. [nQSError: 16001] ODBC error state: S0022 code: 904 message: [Oracle][ODBC][Ora]ORA-00904: "APPS"."XXX_BUSINESS_DAYS": invalid identifier. [nQSError: 16015] SQL statement execution failed. (HY000)
SQL Issued: SELECT "Soft cost Fact".Project saw_0, "Soft cost Fact"."Fiscal Year" saw_1, "Soft cost Fact".XXX_BUSINESS_DATE saw_2, CASE WHEN EVALUATE('APPS.XXX_BUSINESS_DAYS(%1,%2,%3)',"Soft cost Fact"."Soft Cost Date","Soft cost Fact"."Soft Cost Date",1) =0 THEN 'ZERO' ELSE 'NON-ZERO' END saw_3 FROM "Soft Cost" WHERE "Soft cost Fact".Project = '060096' ORDER BY saw_0, saw_1, saw_2, saw_3
Both functions are in same schema, have the similar grants.
Please help me resolving this error. Any pointers in resolving this is much appreciated.
Thanks,
Vijay

I noticed that you have not specified the type of return value that the function returns. It is good practice to do so..
EVALUATE('DB_Function(%1)' as returntype, {Comma separated Expression}).
Try EVALUATE('APPS.XXX_BUSINESS_DAYS(%1,%2,%3)' as number,"Soft cost Fact"."Soft Cost Date","Soft cost Fact"."Soft Cost Date",1) to see if that resolves the error.
Also check this out if you haven't already.
http://obiee101.blogspot.com/2007/12/evaluate-function-and-presentation.html
Hope this helps.Thanks.

Receiving error msg in user's mailbox for both Outbound and Inbound IDocs

Hi,
Whenever specific IDoc (Inbound/Outbound) gets failed then the user/org unit assigned in its partner profile should get those error messages in their inbox.
To achieve this for Inbound Idoc I have performed following set of steps:-
1. Created an object and attached it under IDOCAPPL using 'SWO1' and I have set that object type as 'To imported'.
2. I have assigned that object type to event 'ERRORINPUTOCCURRED' and standard tasks '00008068' (Inbound processing error), '00008074'
(Inbound Syntax error), '20000051' (IDoc Application Inbound error), '300000207' (Error during Inbound processing of SYSTAT01) using transaction 'SWETYPV'.
3. I have created an organisation unit with two positions and different jobs where each job has been assigned to specific tasks. User has also been assigned to specific jobs.
4. At the end of this I have assigned this org. unit to IDoc's partner profile.
But this process does not seem to be working we are not receiving any mail in agent's inbox. If someone has done similar kind of thing in past, please let me know the correct step for both Outbound and Inboud IDoc.
Thanks in advance.
Supriya

Hi,
Try this for inbound IDOC
Go to transaction WE42
Give the process code that you gave in the partner profile (WE20)
Select that row and press the details button (F2).
Next to the "Identification" field there will be push button which has the tool tip "ALE table"
Press that button
In the resulting screen..
In the IDOC section..
Give the following..
object type - "new business object that you created"
Start event - INPUTERROROCCURRED
End event - INPUTFINISHED
Hope this works..
Thanks,
Naren

Ipod shuffle is not detecting in both windows and itunes, its not charging as well

Suddently my IPOD stopped detecting in my PC, i have tried in another laptop with windows XP as well, but still it just blinks 3 times and goes off. Hence i am unable to charge or upload the songs into the ipod shuffle. It was working until 2 days back.
Can anyone please suggest a solution for this problem
I have tried by connecting to different USB ports as well.

Buttons are working fine, because when i switch on the ipod and plugged it in the charger, it shows first as green and then moving to orange (after 3 to 4 blinks) its goes off
And also i tried resetting the ipod as well (as per suggested for 2nd generation)
Today, i gave a try from my another machine \
* i switched off the ipod
* i plugged into the charger
* it blinks for 3 to 4 times and then goes off. with this plugging itself, i switched on the ipod
* i plugged out the cable from the machine and plugged it back immediately
* This time it is getting charged
* i allowed it to charge for 2 hours and plugged out and now i could see playing songs successfully
But the problem the same thing is not working in my personal laptop, it is with WIn 7 (whereas the machine which is working with is WIn XP)
Even i tried to see whether it is detecting in Itunes of my personal laptop, it is not getting detected and not getting charged also. So i uninstalled the itunes and tried again, but it still it is not getting detected in Personal laptop and not charging also.

My iPhone 4s running iOS5 was playing up so I decided to do a DFU restore through iTunes and now I'm getting an error message stating 'The device connected may be damaged and cannot be activated'. PLEASE HELP?

This is the message on iTunes.

this is exactly what mine is doing! let me know if you solve it!

[LP 7.2] Tascam US-2400 detected as both Native and MCU + XT. Help.

I just purchased Logic Pro 7.2 last week and for whatever reason my Tascam Us-2400, which has the latest firmware and is set for Native (Send + AUX5) mode, is detected twice when I launch Logic Pro 7.2. LP sees it first as a US-2400 Native and then also as a Mackie Control Universal + 2 Extenders. With all of this overlap I am unable to use the US-2400 in Native Mode and have reverted to Logic/MCU mode for now and it works, but I lose some key functionality compared to Native Mode.
Has anyone else ever experienced this? I've seatched around and cannot find any additional information. Any help would be appreciated!
Regards,
Mark

Doh! Nevermind. Tascam PDF says to use SEND + AUX 5 to put the US-2400 in Native mode, but the latest/greatest info on the Tascam web site says to use SELECT + CHAN if using Logic 7.1 or later. Works perfect.

Upgrading my HP Envy DV7 - 7205TX with new SSD for OS in bay 1 and HDD in bay 2 with mSATA

Hi guys,
What are your suggestions?
I’m planning to swap one 1Tb drive in bay1 with Samsung 840Pro 512Gb which I want to use for OS Win 8.1Pro.
My question is what kind of configuration will be best for other 1Tb HDD in 2nd bay and 32Gb mSata card which sits on board as well?
RAID 1?
Probably not RAID 0 as I want more reliability for data

Thanks Huffer,
I will consider removing it, (more energy consumption/less battery life)
Or maybe will use it just like a normal drive/ back up option.
What about Intel Rapid Start Technology? It suposed to work with mSATA cache?
Am I right? Will that be useless as well? Better to disable that function?

HP Pavilion g6-2330dx. "No Boot Device. Insert boot disk and press any key" Memory test failed

Hi. So I am trying to help a friend with her laptop. It's a HP Pavilion g6-2330dx.
Product #: D1C01UA#ABA
Serial #: [Personal Information Removed]
Windows 8
ADATA 4GB RAM
Toshiba 640GB HDD from the looks of it.
The laptop is unable to boot into Windows, so I suspect the hard drive. But I ran the hard drive test and it passed all the tests. The SMART test and both the short and long test. I ran the tests multiple times and it passed each time. I tried reseating the hard drive and still no go. I also removed the HDD and connected it to my desktop PC to see if it detects and it did. Ran the Windows 7 own HDD test and it passed.
Currently, there doesnt seem to be any operating system at all on the HDD. When I check, there is a C: drive of ~90GB partition that is ~90GB free, but inside there are Windows files/folders. There is also a D: drive Recovery partition that says ~26GB with only ~2GB free, but when I go inside there's only ~350MB worth of data.
So then I ran the memory test (in BIOS) and it failed immediately. I reseated the RAM module. I tried the other slot. It still failed. So is it safe to say the memory is the cause of this problem?
Pressing the F11 key that is supposed to take me to the System Recovery only leads me back to the black screen with "No Boot Device. Insert boot disk and press any key"
I even tried to install Windows 7 to see if it'll work. I was able to get the laptop to boot/read off the Windows 7. But when I click to install, it asks for a boot device driver or something like that.
My friend doesn't have the recovery disk either. I guess she lost it.
Anyway, is it as simple as replacing the memory or could it actually be the HDD (even though it passes)?
EDIT: This is what the System Log in BIOS says
0021           Time: 10/13/2014
03F0           Time: 10/13/2014
03F0           Time: 10/13/2014
The date was the first time I ran the tests. I havent received those numbers (error codes?) since.
EDIT: Just for kicks, I ran Memtest 2.11 just now (forgot I had the disc) and it immediately went red with thousands of errors, hah.

Hi bghs,
Welcome to the HP Forums!
It is a fantastic place to find answers and information.
For you to have the best experience in the HP forum I would like to direct your attention to the HP Forums Guide Learn How to Post and More
I understand that you were unable to boot into Windows, and you suspected the hard drive and tested it, but it passed both short and long test. With that being said and the fact that it also passed leads me to believe the hard drive is fine.
You tested the memory and it failed. You tried reseating and swapping slots but they still failed the test.
I would test each card individual with the memtest to determine if it is just one or both cards that have an issue.
When you installed it in another computer, you did see the recovery partition. Once the memory issue is resolved, if you are still unable to boot into Windows, I suggest you do a recovery with the minimized image.   Here is a link to Performing an HP System Recovery (Windows 8) to assist you with that process.
I hope this helps.
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

"Inaccessible boot device" error message when I try to boot up.

Greetings, I recently upgraded to Windows 10, and I wanted to do a factory reset yesterday. I did this, and when it tried to boot up after it was finished I got the error message "Inaccessible boot device", and then my computer kept on restarting itself over and over, and never getting into the OS properly. I am using a Portege R705-P35. I tried searching for the device drivers to install on a USB and booting from this, but my computer could not boot from this properly. So i believe my problem is related to the device driver. What is the exact driver I need to boot up? I checked the Toshiba site and there was a list of about 25 drivers for my PC, and I'm not sure which would work. All help is greatly appreciated on this

I have excatly the same issue on my WT8-A. I have been running Windows 10 as an Insider for months on the device, and after RTM decided to do a full reset. I now get the same message as the OP saying "INACCESSIBLE BOOT DEVICE" I now have an unusabe device. Please help.

No boot device available error on Optiplex 780

I need help. We purchased six desktop computers at a going out of business auction to use at our store. We were told that they had all of the previous files removed from the old business and Windows 7 reloaded. On all six of the Dell Optiplex 780 models the start up gives the error of "no boot device available" with the option of pressing the F2, F5 or F12 keys. We have tried changing the boot sequence and engaged the default settings but no luck. These computers were used as a call center and had been hooked up to a "company processing center computer". They were sold "as-is" and there is no one at the old business to talk to. Am I out the money or is there some fix so that these desktop models can actually be used as individual computers? Each computer has the dell service tag and Windows 7 product key codes attached but since I can't get it to a start up page, I can't log on to any internet help from those computers.

Hi HouseofTrains,
There seems to be an issue with the hard drive on your computer. I’d suggest that you run the diagnostics on the computer by following the steps mentioned below and check if there is any issue with the hardware on your system.
Turn on or restart the computer.
Immediately at the Dell logo screen, starting tapping the <F12> key once a second until the One Time Boot menu appears (if the computer boots to Windows turn the computer off and try again).
At the One Time Boot menu, press the <Down> arrow key to highlight Diagnostics, PSA+ or Enter ePSA, then press <Enter> to begin the PSA.
Write down any error codes listed. Reply to us with the error codes.
I’d also advise you to reseat the hard drive on the computer by following the steps below in the link and check if it resolves the issue.
http://dell.to/VWcDMc
Please let me know if this helps.

DV7 - Error 03F0 - No Boot Device Detected - Passes both Memory and HDD Test

Similar Messages

Maybe you are looking for