Dvb Card: Artec T1 USB1.1 TVBOX with AN2235 after Kernel upgrade

Question

Many years I used this card with many different kernel versions. And now after upgrade to 2.6.31 it won't tune in.
She downloads the firmware correctly, which also worked many years without a change. dmesg messages are:
usb 2-1: new full speed USB device using ohci_hcd and address 9
usb 2-1: configuration #1 chosen from 1 choice
dvb-usb: found a 'Artec T1 USB1.1 TVBOX with AN2235 (faulty USB IDs)' in cold state, will try to load a firmware
usb 2-1: firmware: requesting dvb-usb-dibusb-an2235-01.fw
dvb-usb: downloading firmware from file 'dvb-usb-dibusb-an2235-01.fw'
usb 2-1: USB disconnect, address 9
dvb-usb: generic DVB-USB module successfully deinitialized and disconnected.
usb 2-1: new full speed USB device using ohci_hcd and address 10
usb 2-1: configuration #1 chosen from 1 choice
dvb-usb: found a 'DiBcom USB1.1 DVB-T reference design (MOD3000)' in warm state.
dvb-usb: will use the device's hardware PID filter (table count: 16).
DVB: registering new adapter (DiBcom USB1.1 DVB-T reference design (MOD3000))
DVB: registering adapter 0 frontend 0 (DiBcom 3000M-B DVB-T)...
dibusb: This device has the Thomson Cable onboard. Which is default.
input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:0b.0/usb2/2-1/input/input11
dvb-usb: schedule remote query interval to 150 msecs.
dvb-usb: DiBcom USB1.1 DVB-T reference design (MOD3000) successfully initialized and connected.
for me it looks good.
I also have all the
ls /dev/dvb/adapter0/
demux0 dvr0 frontend0 net0
But the famous mplayer:
Playing dvb://ZDF.
dvb_tune Freq: 570000000
Not able to lock to the signal on the given frequency, timeout: 30
dvb_tune, TUNING FAILED
ERROR, COULDN'T SET CHANNEL 23: Failed to open dvb://ZDF.
Exiting... (End of file)

Answer 1

Hi cjpembo,
my Card looks like:
01:07.0 Multimedia video controller [0400]: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [14f1:8800] (rev 05)
01:07.1 Multimedia controller [0480]: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] [14f1:8811] (rev 05)
My card seems to be another version. Regarding to the v4l Wiki: http://linuxtv.org/v4lwiki/index.php/Tu … ted_Tuners
A new Hauppauge WinTV PCI-FM card is here (pci_ids: 14f1:8800, 14f1:8811), using the TCL MFPE05-02 PAL (DK BG I) FM tuner. It just implements mk3 API, you can use philips 1216me mk3 (tuner=38) instead.
If I don't specify any module parameters, the tuner type 0 is selected.
ACPI: PCI interrupt for device 0000:01:07.0 disabled
tda9887 2-0043: destroying instance
tuner-simple 2-0061: destroying instance
Linux video capture interface: v2.00
cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC1] -> GSI 16 (level, high) -> IRQ 16
cx88[0]: subsystem: 0070:3401, board: Hauppauge WinTV 34xxx models [card=1,autodetected]
cx88[0]: TV tuner type -1, Radio tuner type -1
tuner' 2-0043: chip found @ 0x86 (cx88[0])
tda9887 2-0043: creating new instance
tda9887 2-0043: tda988[5/6/7] found
tuner' 2-0061: chip found @ 0xc2 (cx88[0])
tveeprom 2-0050: Encountered bad packet header [00]. Corrupt or not a Hauppauge eeprom.
cx88[0]: warning: unknown hauppauge model #0
cx88[0]: hauppauge eeprom: model=0
tuner-simple 2-0061: creating new instance
tuner-simple 2-0061: type set to 0 (Temic PAL (4002 FH5))
input: cx88 IR (Hauppauge WinTV 34xxx as /class/input/input8
cx88[0]/0: found at 0000:01:07.0, rev: 5, irq: 16, latency: 32, mmio: 0xe6000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
The card is not listed in my local PCI ID repository. And it seems, that the PCI ID is not known to the PCI ID Repository: http://pci-ids.ucw.cz/iii/?i=0070
Badcel
Last edited by badcel (2008-08-24 09:46:18)