DVD burner doesn't fit correctly in Mac Pro

Added a new (second) DVD burner to my Mac Pro. It fits (I took the tray face plate off) but it's tight. So tight it won't eject all the way. I have to help it come out all the way. It's a Phillips DVD burner but seems to be the same dimensions as any other.
I've tested it, it's not the burner that is at fault. It seems to be dragging on the bottom of the slot. Normally, I'd just adjust the seating, but Apple's screw holes don't really allow for adjustment.
How can I make this drive sit about 1/8" higher so it slides out normally?

but it's tight
And how tight did you screw it in because it doesn't needed to be "Nailed Down" just tight enough not to move or rattle! Loosen the screws near the front of the drive a little and see that helps.
Buzz

Similar Messages

  • DVD Burner Doesn't Fit!! Any others?

    Just bought a LaCie 16x LightScribe internal DVD+-R double layer burner since it was recommended on this site, and now come to find it doesn't fit by millimeters due to the mirrored doors.
    Any other DVD burner suggestions? I mean, a size that actually fits the mirror-doored Mac?
    Thanks for taking the time to read this!

    You'd think that all optical drives would be the same size, but they're not. I found that one out several years ago..
    If the drive is indeed too long to mount in the drive carrier and seat fully into the chassis (you say by only a few millimeters) and you've done the obligatory step of removing the tray bezel, the next step would be to remove the entire faceplate of the drive. Depending on the drive, there are usually at least four tabs on the faceplate that hold in the drive chassis. Simply press in the tabs with a small screwdriver while prying the faceplate forward. That may give you the clearance you need to get the drive to fit.
    -Douggo

  • DVD burn doesn't offer correct speed

    I have an iMac iSight (PowerMac12,1 PowerPC G5) with Matshita DVD-R UJ-846 SuperDrive. Mac OS X 10.4.8. According to the Tech Spec this iMac writes DVD-R and DVD+R discs at up to 8x speed.
    If I use DVD-R media, and try to write using a burn folder, Finder says the maximum speed is 2x. Toast Titanium 5.2.3 also says the maximum burn speed is 2x, it correctly reports the disk size as 4.something GB, and offers Simulation mode burn.
    If I use DVD+R media, and try to write using a burn folder, Finder says the maximum speed is 8x. Toast Titanium 5.2.3 also says the maximum burn speed is 8x, it incorrectly reports the disk size as 8 GB, and does not offers Simulation mode burn.
    What on earth is going on?
    I appreciate that Toast is not an Apple product, but I expect Toast is only reporting what Apple tells it, and similar faults appear in the Finder response.
    Does burning from Finder verify the disk, because at the end of the process, there in no window visible saying that verification was successful?
    (Note this does not seem to be related to the fault on SuperDrives relating to High-Speed media (Apple article 86130), because my drive is not a Pioneer drive).
    iMac iSight G5 Mac OS X (10.4.8)

    Note the phrase "up to". The maximum burning speed may be less than that specified on the disk blank, especially if the discs are faster than those available when the drive was manufactured. The drive make, model, and firmware version of the drive, and the brand of disc, may limit the speed to a lower value than that specified for the drive or the disc. For example, the first Quicksilver superdrive would burn 2X DVDs at 2X, but would only burn 4X DVDs (which didn't exist when the drive was made) at 1X. Try different brands of discs. I have good luck with Verbatim DVD-R. The newer Pioneer drives seem to be able to burn discs at their rated speed.
    I don't know why Toast would report the wrong disc size. When using Finder's burn folders, you can click the small round button at the lower-right to see the disc size and space used. Does it show the correct size for the DVD+R discs? Are you sure they are not DVD+R DL discs, which are larger?
    The Finder does verify discs it burns. If you look at the progress bar, you will see it change from "Writing" to "Verifying". If there is a verify error, it will eject the disc, rather than mount it, when finished. It will also display an error window. If the verify is successful, it will mount the disc, but not display a window. Disk Utility gives you a choice of what to do when the burn is complete, and always displays a window indicating success or failure.

  • What external dvd burner is compatible with my 2007 mac mini running OS X 10.5.8?

    What external dvd burner is compatible with my 2007 mac mini running OS X 10.5.8?

    I have an LG GE24LU20 and works great with either my iMac or Mac Mini.
    LG GE24LU20 Optical Drives - 24x External Super-Multi DVD Rewriter - LG Electronics US
    Heck' I can even open and close the tray from my menu bar icon,
    plus it is way faster and less finicky than the superdrives.

  • Lr4 trial version doesn't open on my Mac Pro?

    Lr4 trial version doesn't open on my Mac Pro? Error message: (com.apple.installer.pagecontroller error -1.). Any ideas are appreciated.

    Try running an Apple software update on your Mac.
    See http://forums.adobe.com/thread/1081486

  • The metal flap over the dvd drive won't close on my Mac Pro

    The metal flap over the dvd drive won't close on my Mac Pro.Very annoying,dust will kill.
    Any ideas?

    Hi Toby,
    See if one of these videos shows you how to get to it...
    http://eshop.macsales.com/installvideos/macpro_2010_opt/
    http://eshop.macsales.com/installvideos/macpro_2009_opt/

  • Will a Maxtor Maxline III SATA internal HD fit in a Mac Pro?

    Will an internal Maxtor Maxline Plus III SATA 250GB hard drive (Manufacturer's part 7L250S0) currently in my old G5 PPC fit in the Mac Pro I just ordered today?
    Thanks!

    Any SATA drive should work in a Mac Pro.

  • DVD Burner doesn't show up in DVD SP -

    In the Build & Format dialog box, there is a drop down menu to choose your destination. Only my hard drive is available. Shouldn't my SuperDrive appear there, also?
    I'm having trouble burning a simple DVD - hitting the BURN button results in the response Formatting Succesful - Formatting Finished. The encoded files have been created, I see, but it won't burn a disk. Yes, the DVD media is blank.
    I was able to burn recently using the same machine and software. I'm running DVD SP 4.03. on Mac OS X 10.4.3.
    Why doesn't DVD SP recognize my DVD burner?
    Thanks.

    Sorry, Tom, I disagree. Perhaps you are used to a different OS, but I don't normally think to restart my Mac when I have a problem, nor does any other Mac user I know.
    I am having the same issue. I purchased a new MacPro a couple of weeks ago, installed Final Cut Studio, and did a software update. When I run DVD Studio Pro, it does not show my DVD burner as an output device. A restart did not help. Also, if a restart is required, either the installation or the software update should say so. Neither did.

  • Which DVD drvies will fit into the Mac Pro?

    I have two DVD drives from my PC that will not open and close in the mac pro due to the tray being about 1mm to low.
    I have removed the front bezels off the drives but they are just a bit too low.
    The drives are:
    Sony dw-d18a and Sony dw-Q28a
    Anyone know some drives that will fit?

    The simplest is to match the OEM drives that Apple are using. I know that they use the Pioneer DVR-111D as well a Sony model. Just a search in these forms will give you a specific model.

  • Top DVD tray doesn't fit perfectly

    I have just installed a LITE-ON DVDRW LH-20A1H in the top bay ad moved the original SuperDrive to the lower tray.
    It's all working fine, apart from the LiteOn tray rubs against the bottom of the gap in the Mac Pro enclosure. The flap is coming down completely, but it seems the tray sits lower in this drive than other.
    The tray comes out fully, but the further it comes out the harder it seems to press on the enclosure and it slows down and looks in danger of jamming!
    Has anyone else had this problem? I've not tried it in the lower bay, that might solve the problem but I'll use this drive more, so it makes sense to have it in the primary bay... save me pressing the alt key so often

    I have exactly the same set up as you having installed the LITE-ON LH-20A1H in the top bay and moved the original Superdrive to the lower tray.
    When I first installed the LITE-ON drive I also had the same problem as you with the tray rubbing against the bottom of the gap. I solved it by opening both drives and gently lifting the LITE-ON tray upwards - keeping all edges of the tray away from the Mac Pro gap. I then closed both drives and have never had a problem since.

  • 4 TB Hitachi drives won't fit in 2008 Mac Pro

    I just purchased 2x 4 TB Hitachi drives for my 2008 (3,1) Mac Pro. When I went to install them, they would not fit. I mounted the drives to the sleds, and tried to slide them in. They would only go about 95% of the way, and I could see that the SATA connectors weren't linking up. I pushed fairly hard and couldn't get them to budge.
    I turned on the computer to see if they were mounting, and they didn't.
    On OWC they say the drives are compatible. Any ideas?

    Desktop Hard Drive screws are an SAE (American) #6 size, 32 threads/inch. If you had a die to clean up the threads afterwards, you could file them shorter.
    There is also a common electrician's wire stripper/crimper tool that has dies in the handle for those and a few other common screws used in American Elecrtrical work. You can screw a screw into that die, and squeeze the handles to lop off the end, then back it out to clean up the threads. I was surprised to find one in a drawer, and it has been very handy. Looks like this:
    -- image courtesy Lowes.com
    CD, DVD, and notebook Drives use a metric 3mm screw, 0.5mm/thread

  • DVD/Lightscribe drive for new (late 2010 Mac Pro?

    Does anyone know a source for an internal DVD w/ Lightscribe drive for a late 2010 Mac Pro? I want to install it in the second drive bay. I got one from OWC, but the depth of the DVD drawer was about twice that of the original drive that came with the Mac Pro. It would have been able to fit through the drop cover on the front of the Pro, but would not clear the internal rack components. It fit in the rack nicely with the 4 screws lining up properly, but would then not open more than about an eighth of an inch before hitting the internal rack frame, causing it to close. Thanks.

    Bummer! The instructions included with the drive did not mention thi. When I called OWC customer service she said that sometimes you had to remove the bezel from the Mac. I told her the Pro had no bezel. She said that the drive info did not specifically say it would fit a 2010 Pro a d gave me a RMA.'nmh bad for not questioning further. Thanks.

  • Why won't snow leopard disc fit in old Mac Pro slot?

    I have an old Mac Pro.  Still running 10.5.8 and trying to take the next step to Snow Leopard (10.6).  Just ordered the disc from Apple but the disc won't fit in the plastic tray of the tower!  Any thoughts ... other than ask Santa for a new computer for Christmas?

    Grant, thank you so much for the quick reply.  Yes, you're right, the tower is heavy as sin!  Our more recent computers out west are iMacs which are much easier for us to deal with.  We do have the tower upright.  Bill just moved it here to our vacation house for the winter.  Is it possible [don't underestimate him] that he could have inadvertantly opened the tower DVD slot and a decidedly important part fell out during the disconnect in B'ham?  The discs don't seat themselves.  It's like they're too large by just a smidge and won't sit level in the depression.  As I close the tray the top of the opening scrapes the disc off.  It won't let it go inside so I can begin the struggle with the install itself.

  • I am unable to get a DVD with photos to play on my mac pro

    I recorded my photos on a DVD from my Mac Pro but when placing them im a mac the disc does not come up.  It was readable in a Windows format.

    What software did you use to record the photos on the DVD?
    What software are yiu trying to use to view them?
    What do you mean when you say "the disk does not come up"?

  • Firewire cable not fitting into the Mac Pro Port

    Hi I've got a Sony video camera that's about 7 years, it uses Mini DV. I recently filmed my sister's College graduation that I wanted to view and transfer to my computer. I just purchased a fire wire cable to hook up the camcorder to my mac Pro. The cable fit's perfectly into the Video camera but not the Mac Pro. Did I purchase the wrong cable? It's a Belkin 6-pin to 4-pin Cable. This is the cable that I bought http://www.amazon.com/Belkin-F3N401-06-ICE-4-Pin-6-Pin-FireWire/dp/B00005NIMR/re f=sr11?ie=UTF8&s=electronics&qid=1243482027&sr=8-1. Any help is greatly appreciated.

    Yes - the cable you purchased is FW400, the new Mac Pro's use FW800.
    It does seem like a strange omission not to have at least one FW400 port...
    I have seen some adapter that hook onto the FW400 end, so that you can insert into a FW800. They do tend to be expensive in the area where I live.

Maybe you are looking for

  • Problem Populating Image Item From Database

    Hi All, I am using Oracle 9i & Forms 6i on Windows platform & working in client/server model. I created a form in which, I am reading an image file from the file system & then saving it into the database. In the Databse, i created the column as BLOB.

  • Lightroom Crashes when Using Slideshow after OS X Upgrade to Mavericks 10.9.5 - Can anyone please help?

    I have done a routine OS X upgrade (mac) yesterday to version 10.9.5.  Since then, Lightroom (4.4) has crashed more times than I can count. It is impossible to access the Slideshow Module as it crashes right away.  Lightroom is completely useless at

  • Problems converting Powerpoint/Excel to PDF

    Hi, I have been having problems with how lines in excel come out when printing using Adobe PDF or PDF Creator.  In both cases the thickness of lines, while consistent in excel, comes out completely random in PDF.  My PDFs go to clients and appearance

  • Lightroom/Bridge/InDesign

    I have been urging a friend of mine to switch over to Lightroom, as an alternative to Bridge/Photoshop, as he's currently doing. He's open to the change but has asked me a good question that I can't answer. He does a lot of work with InDesign and he

  • How to Use XMLHttp without using AJAX in JAVA

    Hi... Can any one tell me how to use XMLHttp using Java( not with AJAX or JavaScript). I have one requirement to post one Request to another vendor. that vendor is supporting XMLHttpRequest (developed in ASP). when i try to post request using HttpURL