DVD Burning Engine

I'm using Premier Pro 2.0. To cure the problem of the program not spawning correctly, the program was just re-installed with tech support's help and I was issued a new serial number.
Now the program opens just fine but when I try to create a DVD using the program's built in facility from the WIndow ---> DVD Layout screen, I get the following error message... "Could not initialize the DVD burning engine".
Any help would be greatly appreciated.

Normally, when another piece of software is getting in the way, like Nero's InCD (packet-writing module), one gets "Burner Not Found," or very similar syntax. That does not mean that this might not be the issue, but the error message is not what I would expect, hence my suggestion for the Repair Install.
Still, see the link that John T. provided, as it does cover a lot.
Good luck,
Hunt

Similar Messages

Could not initialize disc burning engine???

For the last few months, any time that I try to burn a DVD I get this error.
I have tried working around the problem by burning to a folder, but PE doesn't do anything (just says 'burning to a folder' and stays on 0%).
Any ideas on why it's doing this or what I could try to do to solve the problem?
Thanks!
Erik

Thanks, Steve, for the info. Here's what I've done:
1. I'm able to create a pure AVI project. I do that and then go to share to disc and get the same error ' could not initialize disc burning engine'.
2. I am not able to burn to a folder. It acts like it will do it, but then it justs sits on 0% and does nothing.
3. I have defragmented, cleaned-up, run antivirus, etc and still have the same problems.
I have gone through your faqs on optimizing vista, maintaining computer for best performance, etc and I'm still having this (and other problems - like the one you were previously helping me with - can't add titles without the program crashing).
The computer is an HP DV2500 with 2.0 Ghz centrino duo and 2.0 Gb RAM and 160 Gb hard drive. I've update my graphics card driver and checked for updates to the DVD burner. 20 Gb is free on the hard drive and I get these same errors for any size (even 10 second) project that I'm working on.
Is there any other further advice that you might be able to give me?
Thanks,
Erik

How do I get around "Could not initialize disc burning engine"

I've just spent ages trying to fix "sorry, a serious error has occurred that requires Adobe Premiere Elements to shut down. We will attempt to save your current project"
After trying umpteen different possible solutions, I hit upon "access McAfee Security Center and turn off the real-time virus scanning".
Phew that got me working again - now I'm trying to burn my movie, but I'm now getting "Could not initialize disc burning engine"
There's been no problems up to now, I've burnt loads of movies before, with no problems.
I've gone into device manager and disabled the DVD writer as per a couple of threads- rebooted but to no avail. In the device manager the DVD status is "This device is working properly."
What can I do to diagnose / resolve this? Any help would be much appreciated as I'm getting somewhat frustrated now having had two problems on the trot.
A bit of extra info:-
My C drive has 287Gb capacity, with 39.6Gb free
I'm on Vista Service Pack 2
4Gb RAM
Intel(R) Core(TM)2 Duo CPU P8400 2.26GHz 32 bit o/s
Thanks in advance.......

Steve
"If you go to Share/to Disc/DVD and select To Folder from the drop-down menu, you will get a VIDEO_TS folder, not an MPEG."
I've tried this, but it's just sitting there at 0%
John Smith
I've tried some of those tips you've linked to.
I've removed Roxio
I've also gone through some of the other links which talk about removing Premiere Elements, uninstalling DVD from device manager, editting upper and lower limits from regedit, and none of this has worked for direct burn to DVD.
I've since done some archiving of files, defragmented disk, so i've now got 71Gb free. So, that's issues with space knocked off the list.
There must be some kind of diagnostics I can run - can Adobe supply any? It seems to be a common problem, but nobody from Adobe seems to be able to supply a decent answer

Encore CS4 (version 4.0.0.258) will not finish burning to blu-ray disc when using a menu template. DVD burning works fine. Anyone know the problem with blu-ray? HELP!

Encore CS4 (version 4.0.0.258) will not finish burning to blu-ray disc when using a menu template. DVD burning works fine with menu template. Anyone know the problem with blu-ray? HELP!

For CS4 you must update the Roxio component, especially with Win8
http://forums.adobe.com/thread/1309029 http://docs.roxio.com/patches/pxengine4_18_16a.zip
http://corel.force.com/roxio/articles/en_US/Master_Article/000012592-PX-Engine-Description -and-Download

Another LaCie DVD burner problem

Hi. I’m hoping one of you Mac geniuses out there can help me out. I received a LaCie DVD burner for Christmas, and so far, I can not get it to work with any Mac software. The drive will burn from Toast 7 Platinum (which was included with the drive), but that’s it. More details:
1. LaCie’s DiscRecording would not install (this should have been my first clue!). So I wrote LaCie Tech Support, and they told me how to manually install the software. This involved creating a DiscRecording folder in the Library on my hard drive. Next I created a DeviceProfiles folder in the DiscRecording folder. Then I dragged the “lacie.drprofile” (from their software disc) to the DeviceProfiles folder, and restarted my computer, as per instructions. This should have fixed everything.
2. I assembled a slide show in iDVD, and went to burn it on my new drive. It whirred for about 3 seconds, and spit out the disc. I received 2 error messages:
#1. BURNING COMPLETE
There were some errors:
Recording engine: internal error occured
#2. MULTIPLEXER ERROR
There was a problem during multiplexing/burning
3. So I decided to try saving my slide show as a disk image, and burn it from Disk Utilities. I inserted a DVD+R disc into the drive, it whirred for a few seconds, then told me the blank DVD that I inserted didn’t have enough room to hold my slide show (the file size is 270mb). After reading of other people’s problems here on the forum, I decided to try again, this time with a DVD-R disc (still using Disk Utilities). I inserted the disc, the drive whirred, and....nothing. The burn box said “Waiting for the drive”, only the drive wasn’t doing anything!!! The little lamp signifying drive activity was dark. And the disc wouldn’t eject!
LaCie Tech Support says as long as the drive burns from their software (Toast), everything is OK. I’m stumped. Any ideas? I’m just about ready to take the drive back and get a different brand. Any recommendations? Thanks.

Buhtwheat,
Thanks for replying. In response to your questions:
Toast will not burn my disk image, it says .img files
are not supported.
Can you play the image file using Apple's DVD Player application?
This is a critical step - double-click on the image file to mount it on your desktop. Open the DVD Player application (in your Applications folder) - select File>Open DVD media and select the VIDEO_TS folder on the mounted image file. Does it play? If so, iDVD is working. I know you've already tried DU, but please try again -try to use Apple's Disk Utility (in your Applications>Utilities folder) to burn the disk image to writable media. See Burning a disk image file on a CD or DVD in Mac OS X at http://docs.info.apple.com/article.html?artnum=93006 Does Disk Utility see your burner? What errors do you see?
The Toast version usually shipped with burners is 'crippled' and can't do everything a full version does. What version of Toast do you have - 6 or 7?
Roxio changed the user interfacer in the different versions and the way you things can be very different in the different versions.
iTunes recognizes the drive.
I think that's a good sign.
F Shippey

Creating a new library from a DVD Burn library

I have my entire library of photos on my iMac in iPhoto 6.0.6. I recently spent quite a bit of time cleaning up what had been a rather messy, unorganized, photo library. My organizational method consisted of consolidating old film rolls which were inherited from original imports that were in different folders by moving groups of photos into single "film rolls" for older years and making fewer rolls for the last few years. I then went back through and corrected photo dates for a bunch of images that were scanned in, etc. I downloaded Keyword Manager, which I like a lot, and applied keywords to every photo in my collection. I also deleted a bunch of old photos which were too similar to better shots or simply not worth keeping. Once I finished all of this I had my new library consisting of 1892 pictures, which I hoped to backup and allow to serve as a "gold master copy" of all of my photos to date. In browsing the database in Finder, I noted that there were a lot of images in the "Original" folders that were not in the library. Some of these were images I had deleted in the library. (I know better than to do anything through the finder other than browse. I know that to maintain integrity of the library it is necessary to only perform actions through iPhoto.) I did a database rebuild and asked iPhoto to recover orphaned files which did nothing. I really wanted this database to be in pristine condition since I was using it as my master copy, but could not figure out how to do away with old unwanted images in the "originals" folders. I went ahead and created a DVD library with "Share -> Burn", and voila, the new iPhoto Library that was created on the DVD appeared to be "clean" with only the 1892 pictures in my viewable library existing in the Originals folder. OK, so far so good. I then took the DVD I had burned and attempted to replicate my library on my iBook which had a clean install of iLife '06 on it. When I launched iPhoto with the DVD in place it showed me an empty hard drive library and the burned library from the DVD. At first I attempted to just copy individual Film Rolls from the DVD to the local library. While this worked in bring the images over, the keywords became all jumbled. The resulting photos would have keywords attached which did not belong to them and were different from what was on the DVD. I then deleted the iBook library and tried copying the entire iPhoto Library folder from the DVD to the iBook via the Finder. When I relaunched iPhoto, presto all the photos were in my local library with keywords, film rolls and other metadata intact. However in browsing the library I came across a few photos which would cause iPhoto to crash when I tried to edit them. This was a consistent behavior on specific images. Reading through the forums I came across the color profile bug and through testing verified that this was not the problem. Meanwhile back on the iMac I could edit the photos in question with no problem. I verified that the image had not been corrupted during the DVD burn as well. The files are identical between the iMac and the iBook. I know this is a long drawn out post, but if anybody has read this far, here are my questions ...
1) What is the best way to go about creating a "clean" database with internal integrity after a doing a lot of edits and metadata changes? Shouldn't the burn to DVD do what I want?
2) How come when I copied subsets of my library over to a new machine from the DVD, the keywords seemed to get all jumbled? Is it a matter of indexing them? If I added all the keywords to an empty library before copying the images over, would it work? Is there not a way to just copy portions of a DVD library into another library?
3) Any ideas on the crash while attempting to edit problem? The image will load as a thumbnail, and then briefly flas the full size image, before iPhoto crashes and pops up a dialog asking if I want to restart it.
Thanks for staying with me!
Mark

Problems solved with iPhoto Manager's rebuild function! Thanks to Brian Webster of Fat Cat Software. Great program!
Mark

I just bought a new mac mini and an external DVD burner. I want to burn a DVD video and it will not play on the TV but only on the computer? Need this figured out for tomorrow.

I just bought a new mac mini and an external DVD burner. I want to burn a DVD video and it will not play on the TV but only on the computer? Need this figured out for tomorrow. Can anyone help me?

Congratulations on the new Mini. Are you saying you tried burning and it does not play, or do you want to burn it only for the computer to be able to play it?
OS X Mountain Lion: Burn a CD or DVD may help.

DVD Burn problem. "Device error - the target device isn't suitable for use"

Hello everyone,
I initially had a lot of problems with PE8. However the nVidia driver update solved most of them.
Just thought it was important to report success as well as failure!
However one problem remains. I get the following error at the 96% mark while burning. "Device error - the target device isn't suitable for use". It is always at the 96% mark and the program is "compiling [something]" when this happens.
Having searched this site I notice that user rgferg posted a similar problem 13 days ago but was redirected to repost in a different place, but never did.
I have tried to burn a 1hr clip 4 times and every time I have selected the slower burn speed (8MB/s) as has been suggested. It seems that inferior media is a culprit, so I have bought some [quality] Verbatim DVD-R media to try in my Phillips SATA optical drive. I am sceptical this will work, but open minded nonetheless. I will give it a whirl when my computer has stopped capturing the VHS I am working on.
Each time the burn failed the disk was automatically ejected and the burn process had actually started and progressed perhaps ~40% or so.
This indicates to me that it is a drive sharing issue, rather than a media issue. Somewhere on this forum it suggests that I go through a 20+ step process and delete/disable every piece of software that can compete with Premiere among other things. IF I do this what do I burn with outside of Adobe? Do I have to get imgburn or whatever it was called? What if I like Nero? Nero 6 has worked great for me for 3 years.
So given I am willing to uninstall my old optical drive burning software, who out there can recommened commercial software that for them creates a painless Adobe burning experience with no errors or conflicts? Perhaps there is another solution that I did not see on this forum?
I am running Windows XP SP3. I have the latest nVidia drivers for my SLI GeForce 7600 GS cards. I have 3 monitors. RAID 0 SATA, 2GB RAM, Athlon X2 5400.
Justin.

OK been working through the list of 20 things Adobe recommends to fix DVD burn error. No luck yet:
system meets minimum requirements
Project size does not exceed disk capacity
successfully burned project to DVD folder -thus skip to step 8.
8. Using new blank media for burning
9. Try different media and DVD burners. Bought Verbatim DVD-R. Don't have another DVD burner. Adobe's supported burner list is VERY short, so of course mine is not on it.
10. Uninstalled Nero 6. Did NOT uninstall Acronis True Image workstation or Lightscribe. These do not access the drive unless I say so!
11. Have not yet disabled startup items and services. This will take a lot of work and will leave to last. Deactivated Spybot thus far.....
12. Disabled IMAPI CD burning COM
13. DMA if available already set. Haven't set this in BIOS yet. I already think it is, but will check next boot.
14. Updated DVD firmware
15. Already updated nVidia drivers
16. Don't have any other DVD drives to disconnect.
17. MPEG workaround. Will resort to if required.
18. Disable Autoplay? XP only has "prompt me each time to choose an action". I have set this for ALL file types.
19. Have NOT refreshed the DVD drivers in the registry. This step involves uninstalling PE8. Will leave this as last resort.
20. Visit forums to see if other have the same problem. Hi guys
So still working through some of the items above.
Can anyone direct me to advice on how to write the encoded files sent to the hard drive, or the VOB files that PE8 failed to burn to a disk? Will the former work with DVD menus?
What a process.
Stay tuned.
Justin.

Problems ripping with an external DVD Burner

Hello Everyone,
Recently I purchased a Liteon External DVD Burner off of newegg (http://www.newegg.com/Product/Product.asp?Item=N82E16827106011) -- It's a Liteon SHW-1635SX -- I bought this because the DVD-ROM drive thats in my tower natively is REALLY slow and I wanted to get a new one that I could use with a laptop that I`m going to purchase in the future. Whenever I try to rip a CD into iTunes using the burner, It says that it's ripping the disk, however it doesn't spin up the cd and it takes about 2 seconds to "rip" all the songs. I know this drive is soposed to be faster than my old one, But two seconds is a little TOO fast. Plus, I know that it's not copying the songs because when I try to listen to them in my library, the song won't play. (Under time it says "789:54..." for all the songs on the cd, in my library) However, the burner rips perfectly in Windows Media Player... Is this perhaps some kind of glitch with iTunes??? Basicly, the only way I can rip a CD into iTunes is to use my old DVDROM drive, but that defeats the purpose... below is the CD Diagnostic log that I got from iTunes::::::::
Microsoft Windows XP Home Edition Service Pack 2 (Build 2600)
HP Pavilion 05 P9859A-ABA 533w
iTunes 6.0.4.2
CD Driver 2.0.4.3
CD Driver DLL 2.0.3.2
LowerFilters: PxHelp20 (2.0.0.0), AFS2K (3.1.21.0), DRVMCDB (1.0.0.1), SSCDBHK5 (1.0.0.1), PFC (2.5.0.196),
UpperFilters: GEARAspiWDM (2.0.4.3),
Video Driver: Intel(R) 82845G/GL Graphics Controller\Intel(R) 82845G/GL Graphics Controller
IDE\DiskMaxtor4R060J0_________________________RAMB1TU0, Bus Type ATA, Bus Address [0,0]
IDE\DiskST34323A_______________________________3.02___, Bus Type ATA, Bus Address [1,0]
IDE\CdRomCOMBIRW16x10/DVD_______________________H1.0___, Bus Type ATA, Bus Address [0,0]
USBSTOR\CdRomLITE-ONDVDRW_SHW-1635SYS0Y, Bus Type USB
If you have multiple drives on the same IDE or SCSI bus, these drives may interfere with each other.
Some computers need an update to the ATA or IDE bus driver, or Intel chipset. If iTunes has problems recognizing CDs or hanging or crashing while importing or burning CDs, check the support site for the manufacturer of your computer or motherboard.
Check the Windows Update website to verify that you have the latest service packs and patches for your OS. Service packs affect the performance of USB and firewire CD / DVD drives.
Current user is administrator.
E: COMBI RW16x10/DVD, Rev H1.0
Drive is empty.
F: LITE-ON DVDRW SHW-1635S, Rev YS0Y
Audio CD in drive.
Found 9 songs on CD, playing time 42:13 on Audio CD.
Track 1, start time 00:02:00
Track 2, start time 03:30:07
Track 3, start time 08:44:33
Track 4, start time 12:03:74
Track 5, start time 17:55:53
Track 6, start time 22:14:31
Track 7, start time 25:32:60
Track 8, start time 30:13:01
Track 9, start time 35:59:06
Audio CD reading succeeded.
Get drive speed succeeded.
The drive CDR speeds are: 8 16 24 32 40 48.
The drive CDRW speeds are: 8.
The drive DVDR speeds are: 8.
The drive DVDRW speeds are: 8.
The last failed audio CD burn had error code -128(0xffffff80). It happened on drive E: COMBI RW16x10/DVD on -128(0xffffff80) media at speed 0X.
Your replies are greatly appretiated!
--Aric--

hi Aric!
hmmm. we'd better check on the usual suspects with that. (the incredibly long song times can also be associated with these sorts of causes.)
You can't import or play music from an audio CD in iTunes for Windows
... and the following resources might be helpful with that. (check on firmware and drivers even though it's a brand new unit.)
Using CD Diagnostics in iTunes for Windows to troubleshoot CD/DVD drive issues
iTunes for Windows: Updating the firmware on your CD or DVD drive
Updating the drivers on your Windows PC
Where to find firmware for your CD/DVD drive
love, b

My DVD burning problems solved....here's what I did.

Like some of you, I was having MAJOR problems burning DVDs. My initial setup was a dual 2.0 ghz G5 purchased in July of last year, so it came with a 8x burner and iLife '04 (iMovie 4.0.1 and iDVD 4.0.1). Seeing as how I have 1.5gigs RAM and a fairly new system running 10.4.3, I didn't think I was going to have any problems burning DVDs....
HA.
Nothing worked right......a 1-hour long project burned for more than 8 hours without finishing, or iDVD would quit for no reason, or the burn would fail. I noticed that Terminal said that during these burns it was only burning at 4x even though 47x was requested. Chapters were not working. Applecare was not helpful, only suggesting that I try to burn under a new user, and then call them back. That didn't work either.
I probably took the lazy man's way out, but I decided this waste of time was unacceptable. I went out and purchased a 16x SuperDrive Pioneer DVR-110D replacement from MCE for $92, and upgraded to iLife '05 for another $79. I installed the drive myself (VERY easy with the included instructions), and tried the new setup under a newly created user.....
PERFECT burning every time. Not only that, but Terminal showed a requested burn speed of 16x and a burn speed of 16x. A two-hour project is now burning in less than 8 minutes. Multiplexing still takes time, but it's less than 1 hour!
On an interesting side note: when I try to burn under my regular user name, I STILL get an burning error (says image not complete, or incomplete....something like that). But under the user name created just for burning I have no problems. The chapter problem was solved when I stopped putting a chapter marker at the very beginning of my iMovie projects, since iDVD automatically puts one in called "Beginning," which you can change to anything you want.
Maybe this will help others.....
Dual 2Ghz G5 Mac OS X (10.4.3) 1.5 gigs RAM, iMovie 5.0.1, iDVD 5.0.1

it was only burning at 4x even though 47x was requested.
That's a issue discussed in the past.
It turns out that 8X DVD burning means about 47X CD burning - you were requesting 8X DVD but only got 4X DVD burning.
I haven't seen it discussed anymore so maybe Apple got around to eliminating that 'quirk' in terminology.
I suspect some of the early 8x DVD burners didn't perform as advertised. I'm glad your new 16X burner is working for you.

ITunes Seem to Have Suddenly Stopped Communicating With the CD/DVD Burner

Hello, I wonder if anybody can help - my itunes application seems to have suddenly stopped communicating with my laptop's cd/dvd burner
(Generic Name (E: H - T-S D D A S - 20N ATA Device)).
About 2 years ago, I have experienced a similar problem, but was able to resolve it by downloading 64-bit compatible GEAR drivers to my system. However, the problem has re-appeared when I have updated to iTunes Version 10.1. Funny enough, the cd/dvd burner started getting recognized again when I updated to iTunes Version 10.2, but halfway through me burning a large playlist to multiple cds has suddenly stopped recognizing the cd/dvd burner again, and has never "resolved itself" ever since.
I have tried multiple approaches to solving this issue, including completely re-installing itunes software and completely re-installing GEAR drivers, but nothing works. I have even tried uninstalling GEAR drivers completely, as I read that it worked for someone on one of the similar forums, but that didn't work either.
My itunes diagnostics runs all the points of the cd/dvd drive check successfully, except for the last point (Can Not Read Audio CD). Here's what the diagnostics summary looks like:
Microsoft Windows Vista x64 x64 Home Premium Edition Service Pack 2 (Build 6002)
Hewlett-Packard HP Pavilion dv9700 Notebook PC
iTunes 10.2.1.1
QuickTime 7.6.9
FairPlay 1.11.16
Apple Application Support 1.5
iPod Updater Library 10.0d2
CD Driver 2.2.0.1
CD Driver DLL 2.1.1.1
Apple Mobile Device 3.4.0.25
Apple Mobile Device Driver not found.
Bonjour 2.0.4.0 (214.3)
Gracenote SDK 1.8.2.457
Gracenote MusicID 1.8.2.89
Gracenote Submit 1.8.2.123
Gracenote DSP 1.8.2.34
iTunes Serial Number 0016AB580A7B0C28
Current user is not an administrator.
The current local date and time is 2011-04-14 17:52:25.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is not supported.
Core Media is supported.
Video Display Information
NVIDIA, NVIDIA GeForce 7150M / nForce 630M
** External Plug-ins Information **
No external plug-ins installed.
The drive F: Motorola MB810 Rev 0001 is a USB 2 device.
iPodService 10.2.1.1 (x64) is currently running.
iTunesHelper 10.2.1.1 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.
** CD/DVD Drive Tests **
No drivers in LowerFilters.
UpperFilters: GEARAspiWDM (2.2.0.1),
E: H-T-S DDA
S_-20N, Rev W_05
Audio CD in drive.
Found 1 songs on CD, playing time 255:08 on Audio CD.
Track 1, start time 00:02:00
Audio CD reading failed. Error Code: 27 27 27 27 27 27 27 27 27 27 27 27 27 27 27 27 0 0 0 0.
iTunes cannot play or import music from a CD in this drive. The drive may need a firmware update. Check with the manufacturer.
Get drive speed succeeded.
The drive CDR speeds are: 3 9 16 24.
The drive CDRW speeds are: 3.
The drive DVDR speeds are: 3.
The drive DVDRW speeds are: 3.
Error Correction is turned on for importing audio CDs.
I have noticed that the diagnostics summary containes a suggestion to update firmware of my laptop's cd/dvd drive, but currently there are no such firmware updates available.
Another frustrating issue that I ran into was trying to convey this issue to Apple Technical Support via e-mail using the Express Lane for the troubleshooting issues. I really fail to understand why I am being asked for the "hardware serial number" when I'm clearly choosing the categories for "iTunes/CD-DVD Import Issues" which are software, not hardware, categories! This prevents me from being able to simply send the description of my problem to the correct Apple Support department, and does not let me do that even when I enter my itunes' Serial Number, which can be found in the diagnostics summary provided above.
Much Thanks to anyone who can provide any kind of helpful advice, even if it's just on how to be able to convey this problem to Apple Support via e-mail!

Okay ... checking something else:
Current user is not an administrator
Is that true? Or do you in fact have a Windows user account with full administrative rights?
(It's possible that a permission may have gone astray in your usual user account, which might be causing the burning issues.)

Possible to install HD-DVD Burner in iMac G4?

Hi, I was wondering if it is at all possible to install HD-DVD burner in a iMac G4? Anyone tried this?

I know that Toast Titanium 8 for Mac supports Blu-Ray burning (Apple's loyalties are in the Blu-Ray not the HD DVD camp) but the G4 is not a processor I'd ever want to be encoding HD in. The G4 wouldn't even be up to playing discs. So I think you could do it with a Blu-Ray drive but you shouldn't do it. I hate having to wait whilst an SD DVD encodes HD is at least four times longer. Remember Apple hasn't put a HD spec burner in even it's 8-core Mac Pro yet!
mrtotes

Looking for a external blu ray dvd burner for my mac

looking for a external blu ray dvd burner for my mac

There are plenty of options but I have found that the LaCie d2 http://blu-ray.burnworld.com/burners/lacie-d2.htm works more consistantly. I use Toast 11 mainly for Blu-Ray. The drive does come with a basic verison of the software which is good for most but you need to upgrade to do some serious authoring.

DVD burn error message

I get this error message when I try to burn a data DVD: "Burning the disk failed because communication to the disk drive failed. (error code 0 x 80020022)
I am attempting to use the original drive system (Pioneer DVD-RW DVR 104) and it plays CD's and DVD's without a problem. Thoughts? Jim

just had this problem with a 17" MacPro purchased in Jan 09. Toast Titanium 9 had no problems burning the CD. tried it again in Finder but backed the burn speed down from 24x to 8x - no problem.
I can only assume it is cheap media causing the problem - we have no problems with Maxell CDs at full burn speed (24x). The CDs causing the problems are Verbatims (rated at 1-52x) that have printable surfaces.
hope this helps

G5 DVD burner error message? Help please?

I get this error message when I try burning a 1gb quicktime movie to dvd on my pre installed standard burner. Thanks in advance
the link below is a screenshot of the error
http://www.darkstargraphics.com/dvd_message.gif
Im at a loss and ready to by another
below is the dvd burner profile
PIONEER DVD-RW DVR-106D:
Firmware Revision: A606
Interconnect: ATAPI
Burn Support: Yes (Apple Shipped/Supported)
Cache: 2000 KB
Reads DVD: Yes
CD-Write: -R, -RW
DVD-Write: -R, -RW, +R, +RW
Burn Underrun Protection CD: Yes
Burn Underrun Protection DVD: Yes
Write Strategies: CD-TAO, CD-SAO, CD-Raw, DVD-DAO
Media: No

The error "internal target failure" appears on PCs using this drive as well, so it appears that it's not a Toast specific error.
However, in my browsing, no one seemed to be able to tell if it was a true hardware failure of the drive, or if it was caused by poor quality media.
I'd try other brands of media and a lens cleaner before flashing the firmware. And, if you do decide to flash the firmware, the current, official firmware for that drive is here. The link in MLCinma's post contains hacked (region free) firmware and is outdated in any event.
Let us know what brand of media you're using and what speed you're burning at.
The DVR-106D has had lots of reports of failures, so it could very well be the drive. At least a replacement DVR-111D will only cost you about $40 - $50.

DVD Burning Engine

Similar Messages

Maybe you are looking for