DVD playing issue

I have burned a DVD with menus. When this DVD is played in any DVD player, the menu and the slideshow works, but when you select the play button the movie will not play. The menu does its transition and then the counter on the dvd player goes to zeros and stops. You can hit the menu button on the remote control and it will go back to the menu. The video was rendered in compressor as a mpeg-2 and dolby digital 2.0 audio. I am not sure if this is right but in DVD Studio Pro I made a menu for the opening menu and then another menu for the scene selection. I also made a separate menu for each page of the scene selection. Should it be a separate menu or submenus? Would that make a difference or make it not play?

I just burned a dvd without the menu and the video plays fine. So now I am not sure which way to go. Even the buttons in the scene selection will do the same.
So none of the buttons are working? Are you using DVD SP on the Tower or the MacBook? The Macbook is not spec'ed to use the FInal Cut Studio
Along the same lines which version of DVD SP are you using. To run on MacIntels you need the Universal Binary version - if you do not have the universal BInasry Version (Final Cut Studio 1 or 2) then you can also run into issues.

Similar Messages

Dvd play issue on my macboook!!!

hello people,
i have what u might define as a simple problem but i cant fix it....
i have a dvd service where i rent a bunch of dvd's, the last couple i watched on my macbook but the video comes out to be a little block in the middle of my screen (so i thought it might just be the movie), but today i tried to play the dvd on my tv.... and the aspect ratio is 16:9
how come does this happen??
could it be certain movies have that funny aspect ratio?
please give me some solutions
thanks in advance

Some old DVDs are wide format rendered within standard 4:3 non-wide NTSC. That would explain what you experienced. I am guesing the last two DVDs you rented are old.

DVD Plays on computer drives, but not on dvd players

iDVD 06 - This is a new problem, just happened two days ago. Previous dvd's burned with idvd 06 work just fine on old and new dvd players. I always test them after burning. However this new project will only play on computer dvd drives (mac or pc) but not on my dvd players. The menu screen shows up, but when the play button is pushed it never starts. Disk is clean, re-burned dvd, re-exported the video and re-did the entire dvd, same issue. I have not changed any settings in iDVD 06.
Yes, I even re-installed idvd 06, but then somehow I lost some of my old themes (which happened to be the ones I wanted to use) I did back up my previous copy of idvd 06 which has my old plain themes that I love to use in the package, so I do have those. But if I bring them into the newley re-installed idvd 06, all the features do not work. Such as being able to change the type size on that paticular menu.
I am using Verbatim 8X DVD-R's and have successfully used these just the other day on another project! And those work just fine on an old and new dvd player!
I had to get these dvd's because my burner would not burn on the 16X DVD-R's that I recently bought.
DVD Burner information is:
SONY DVD RW DW-U10A:
Firmware Revision: A43h
Interconnect: ATAPI
Burn Support: Yes (Apple Shipped/Supported)
Cache: 0 KB
Reads DVD: Yes
CD-Write: -R, -RW
DVD-Write: -R, -RW
Burn Underrun Protection CD: Yes
Burn Underrun Protection DVD: Yes
Write Strategies: CD-TAO, CD-SAO, CD-Raw, DVD-DAO
Media: No
Computer information:
Machine Name: Power Mac G5
Machine Model: PowerMac7,2
CPU Type: PowerPC 970 (2.2)
Number Of CPUs: 1
CPU Speed: 1.8 GHz
L2 Cache (per CPU): 512 KB
Memory: 1.5 GB
Bus Speed: 900 MHz
Boot ROM Version: 5.0.7f0
Any suggestions???
G-5 Mac OS X (10.4.9)

No rhyme or reason... but tried one more time after putting back my old copy of idvd 06 with my oldest themes in it, and I now have DVD's that will play on regular DVD players!
Now, if Apple could just get us a firmware update for the SONY DVD RW DW-U10A which came with my G-5 and then maybe we could all burn disks at the new 16X speed! Instead of limiting our possibilites.
Oh and yes, I did contact Sony about firmware updates. They informed me that this is really an OEM drive (whatever that is) and that Sony does not support it!

Third party DVD player issues

Recently, I have come across an issue playing back DVD's with
VLC or XBMC. When I start playback of the DVD, it plays the first
segment ( the studio leader at the beginning) and will then just quit.
Apple's DVD Player works fine (quality is crappy and can't get surround
tracks out of it). Yet, when the DVD is ripped to the hard drive and
played from there, it is works just fine.
Also, this happens when the DVD is played back from an internal
or external drive.
Has anyone else seen this issue or do I have a unique problem?

My unit is a 2010 MacMini with HDMI. (see list)
The quality issues with Apple DVD player vs. other solutions are certain
scenes have a graininess akin to noise on old analog tv's that aren't
present on the other players and severe banding in gradients that
do not appear in other players, at least when they were working.
As far as the audio, selection in the DVD's menu itself just makes no difference.
Tried all the combinations of messing with Audio MIDI setup, third party
plugins like Perian, none of which work for Apple's DVD player. This was
the other reason for going to third party players, the higher quality video
was just a bonus.
Your point has been taken that it may be a software issue with the third party players.
Some update at some point may have broken them, be it OSX or their own.
I've beaten the Apple DVD player issue enough, let's just consider the topic dead.
The audio issues with it are spread over many, many threads across the web, with
no silver bullet solution to all.
As for BluRays, play them back all the time on my Mini. Either with
PowerDVD 10 in a Bootcamp windows7 when I want full DTS-HD or
TRUE HD decoding (decodes these to up to 24 bit,192kHz 7.1 since the
Mini chipset does not have the "protected" path for pass through of
these technologies) or a MakeMKV/XBMC combo in OSX. The OSX
solution doesn't give you the fancy menus and all or HD audio if present,
but if I only want to watch the movies it's fine. If I ever do want the other
nonsense, I just use PowerDVD 10. And please note this is BluRay disk
in player, not "ripped" or transcoded.
I do appreciate your help, but was primarily curious if others had issue
as well.
Message was edited by: woodmeister50
Message was edited by: woodmeister50

2.1.2 update does not fix DVD Navigation issues :(

The FrontRow 2.1.2 update still doesn't fix the DVD navigation issues where sub menus on MANY DVDs are not navigable. Using the up / down keys on the keyboard or remote causes the Volume to change and not navigating the menus like it is supposed to.
This is a severe issue as it makes it impossible to play some DVDs or turn on the subtitles.

Yeah, I have experienced this as well. Ridiculous -- how could this issue not have come up in product testing by the time the software has reached version 2.0? The solution on Apple's end should be obvious. All 4 directional buttons must act only as directional commands when using a DVD, and all other functions (such as volume) can only be accessible by hitting MENU first to bring up a list of other options.
I'm all for simplicity, but this is the fault of the boneheaded 6-button Apple Remote. It requires their software to overload buttons with different commands depending on context, which is clearly an unacceptable limitation. They'll have to break down and roll out a proper remote with more discrete buttons one of these days and come to terms with the fact that shoehorning everything onto 6 buttons is not an elegant solution.

Created project in PE4, burned to DVD - plays on Computer but not on DVD Player.

Created project in PE4, burned to DVD - plays on Computer but not on DVD Player.
Vista Ultimate
Let me know what other info you need.
Thanks for your help.

Yes, the lowest possible Burn speed will be a step in the direction of compatibility.
As for the Quality setting, Robert Johnson has done tests on various versions of PE and has recommend a setting of about 7.8 (IIRC). Unlike Encore, where one has many more choices, PE limits one to a Quality setting of 8. This is about equivilent to the recommend 7MB/s in Encore. Robert found that just below the 8 max. actually yielded slightly better results, than did the full 8, on his tests.
The three things that help to insure the greatest compatibility with set-top players are, and in pretty much this order:
1.) Quality media - Verbatim, Taiyo Yuden or Falcon (US only)
2.) Burn speed (slower is better. It might take a few minutes more, but if it works, you don't have returns or have to do it again.)
3.) Bit-rate around 7MB/sec
Remember - no set-top player HAS to play any Burned DVD. Most do, but some just do not - only replicated, pressed discs. Also, some player are still sensitive to the -R and +R media types. This is less a problem with newer units, however it still could be an issue with many older ones.
Personally, I test a "master" on four different players, plus my computer, before I Burn a batch, or ship out any. One unit is a very high-end Marantz, another is a mid-level Marantz, one is an RCA "el cheapo" and the other is an older Pioneer. I figure if the disc plays everywhere, there is a good chance that it will play for the client - though there are still no guarantees.
Good luck,
Hunt

BURNED DVD PLAYS WITH SOUND ON PC BUT NO SOUND WHEN PLAYING ON TV ???

BURNED DVD PLAYS WITH SOUND ON PC BUT NO SOUND WHEN PLAYING ON TV - VIA VIDEO PLAYER ??

Hi,
It may be worth trying another burning application to see if this helps the issue.
Download and install the free utility, ImgBurn and use this to create the DVD. Guides on using this to burn to single layer and dual layer discs are below.
Burning DVD Files To Single Layer Discs
Burning DVD Files To Dual Layer Discs
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

975x Platinum POE DVD Playback issue

My system components are as follows:
975x POE Motherboard with offical bios version 7.2
Intel Core 2 6300 1.87GHz CPU
Ultra Xfinity 600W PSU
Samsung Writemaster DVDRW
Liteon DVDRW
Maxtor 6L300R0 300GB PATA Hard Drive
Asus Radeon x1600 with latest drivers
Now, on to the issue. DVD play back, with use of various codecs and programs (i.e. Power DVD 6, Media Player Classic), is jerky with crackling audio. This happens with both of the DVDRW drives and with each hooked up as a single drive on the IDE channel. I've also tried a new IDE cable. I've enabled hardware acceleration in the options of every program I've tried to play DVDs with. I've installed the latest chipset, video, audio drivers. I've disabled the onboard sound and installed a sound card to rule out the onboard sound as the cause. I've reinstalled windows twice, and for a short time after reinstalling windows, everything works fine. Eventually, though, the system will hang or even restart during a DVD and after that, the playback is choppy with crackling audio all the time.
Any help will be greatly appriceated.

OK,the easiest option for you is to connect the optical drives on the blue IDE controller(set the drives as master and slave), and the IDE HDD on the yellow one, witch will be controlled by Jmicron. Before doing that, uninstall jmcron in Device Manager-SCSI and RAID Controllers, and uninstall JRAID in Add/Remove programs. Then turn off your PC,switch the devices and then start your PC.When Windows starts,Found new hardware will appear, and that's the point when you'll install the drivers that were supplied with the MB.

HP DVD Play BD fail

I believe have the latest firmware (sp44374 from april 2010) but I cannot play Avatar (either the stansard edition or the collectors). Any news on more recent updates? Why can't they fix this problem of not finding updates? I had to search the internet for hours and found nothing that works.

Hi,
It is a known issue with HP PCs running new BDs with HP DVD Play/MediaSmart DVD applications,
download and install PowerDVD Trial and play the Avatar Movie with.
http://fs20.filehippo.com/8364/8de9788827844c8e9a5071f7ee9232c4/CyberLink.2325(Trial)_DVD101118-01.e...
You may have to wait until a new Update for HP DVD BD Play/MediaSmart is released
Thank You.
Kiran Talluri
Say thanks by clicking the "Kudos! Star" which is on the left.
Make it easier for other people to find solutions, by marking my answer "Accept as Solution" if it solves your issue

DVD Playing in Fast Foward After Burn

1. DVD simulates perfectly in DVDSP.
2. Put it in one dvd player and it's like it's being fast forwarded. Menu, first play, everything. Not a DVD player issue.
3. Put it in another DVD player and similar thing happens. It fast forwards part of the video and the voice gets off of the video. This is in the first play track.
Never seen this before and need help. I've done over 20 DVDs in DVDSP so I'm not a newbie.

It was a piece of video in the First Play that caused the problem. It was encoded at 6.2 MBPS while the main track was 5.0. Not sure if that was why but re-encoding that video fixed it.

How can I watch a DVD playing on my iMac on my TV using Apple TV?

How can I watch a DVD playing on my iMac on my TV using Apple TV?

You can't. The only way is to transfer the movie to your computer and import to iTunes (making sure it is compatible) and either use home-sharing or airplay the movie off an ios device.

ITunes for 64bit Windows 7 Driver/CD/DVD/Drive Issues-

Hi There
I am sure that there are many many users out there suffering the same frustration as me in regard to ITunes just not working properly with Windoews 7 (64Bit).
I have been trying to solve the mystery of "ITunes for Windows Registry Settings Warning When Opening Itunes.
I have tried all the recommended actions to correct this problem without any success and I do mean ALL.
Below is a screen shot of my registry, can anyone see anything wrong with it?
In the meantime (Last four months) I have stopped using ITunes and instead have used Digital 7, this will be my very last attempt to get ITunes working properly, failure will mean consigning ITunes to the same place as any other Software that does not do wshat it says on the can.
I hope someone can help.

That's good that it is in device manager, but what about in Computer with the rest of the drivers?
Also, are the drives listed in Computer and device manager or just device manager?
I want to verify if the symptoms are present for a particular software issue before looking at other issues. I really doubt it is a driver issue at this point. If it was, then I suspect the issue would be present from day one.
It could be that the lens has dust buildup preventing it from working properly. They do make CD cleaning kits that have a special CD designed to clean the laser as it passes over the lens. If you happen to have one of these, or access to one, I recommend trying this step to make sure it isn't as simple as dust buildup interfering with the laser.
It could also be hardware failure, but I would like to try a few other steps before coming to that conclusion.
It may be worth reviewing this document as it covers a lot of the most common issues behind DVD drive issues. Feel free to skip any steps you have already tried.
Let me know what happens.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

I still have Cd/DVD drive issues

The CD is ejected after a short while and never mounted. I have cleaned the optics of the CD drive and reset my PRAM.
Has anybody discovered a complete solution for this problem.

That's good that it is in device manager, but what about in Computer with the rest of the drivers?
Also, are the drives listed in Computer and device manager or just device manager?
I want to verify if the symptoms are present for a particular software issue before looking at other issues. I really doubt it is a driver issue at this point. If it was, then I suspect the issue would be present from day one.
It could be that the lens has dust buildup preventing it from working properly. They do make CD cleaning kits that have a special CD designed to clean the laser as it passes over the lens. If you happen to have one of these, or access to one, I recommend trying this step to make sure it isn't as simple as dust buildup interfering with the laser.
It could also be hardware failure, but I would like to try a few other steps before coming to that conclusion.
It may be worth reviewing this document as it covers a lot of the most common issues behind DVD drive issues. Feel free to skip any steps you have already tried.
Let me know what happens.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

DVD plays well on some machines, gets stuck on others

Made a 20-minute DVD, having done all my editing, etc. in iMovie and exported to iDVD5. Once burned, tested it on my iMac and it worked fine. Also worked fine in a friend's stand-alone DVD player.
But some users since have this problem: the DVD plays well for a few minutes, but gets "stuck" after a while, and ultimately freezes. And it's not the same "stuck" point for each user (if that was the case, I would think the physical disk had a problem.) It's different points for different people that it seems to get "stuck" and freezes.
In one case, user took "stuck" disk out of stand-alone DVD player and watched it in their laptop (PC) and all went well.
Any hints as to why the DVD is getting stuck on some DVD players?
iMac G4 Mac OS X (10.4.4
Mac OS X (10.3.8)

Probably a "bad" burn, the result of a DVD-R that some players don't like.
Try these things:
1) another brand of DVD-R (I Like Verbatim)
2) Burn at a slower speed. To do this with iDVD you have to "save as disk image" and then burn the image with Disk Utility (DU) or Toast. For some reason, I can't always choose slower burning speeds with DU, not sure why.
John

IMac will not play the DVD that I have made on imovie and burned on iMac SuperDrive ?? (DVD plays fine on household DVD player and also play fine in Toshiba laptop ) Why not on the iMac - anyone know???

iMac will not play the DVD that I have made on imovie and burned on iMac SuperDrive ?? (DVD plays fine on household DVD player and also plays fine on Toshiba laptop ) Why not on the iMac - anyone know???

There are many reasons this could be the case but whether an optical disc can be read or not is a function of:
The reflective media layer of the disc
Whether the burned disc was a DVD-R, DVD+R, DVD-RW, DVD+RW
The brand, model, and production lot of the disc
The specific frequency of the Write lasers that burned the disc
The specific frequency of the Read lasers that are attempting to read the disc
Are the Read lasers in the drive working (it is common for one set of lasers in a drive to fail while others continue to work)
How old are the Write and Read drives (laser frequencies change with age)
Is there dust on the read laser
Is there dust on the read lens
etc.
At one time it was estimated that fewer than 80% of all burned discs were readable in 90% of the drives. That has, I believe improved over time but at the same time it seems the faillure rate of lasers in the drives has increased but that may simply be the result of how many different read and write lasers there are in today's superdrives. Fortunately todays drives are a lot less expensive the replace -- now that Apple no longer installs optical drives in their computers.

DVD playing issue

Similar Messages

Maybe you are looking for