DVD ROM Empty

I'm new to apple and idvd. I am making a dvd of some slideshows I made in iphoto, I have the box checked for "Always add original slideshow photos to DVD-ROM" in idvd preferences. I imported the slideshows into idvd, and checked out the dvd-rom file, and to my dismay it was empty, I was expecting and hoping to see that the pics of my slideshows would have automaticly showed up there. Did I do something wrong or will they show up after I burn the dvd?

They should be there. Go to Advanced/Edit DVD-ROM Contents... If not there add them. I don't use iPhoto so I'm not sure how you'll get them in... Sorry.

Similar Messages

PowerMac G5 doesn't work anymore simply due to a DVD-ROM drive removal!

Hello, here's what's happened (I'll write using the "present" because I'm not English).
This happened about two days ago:
I need to read an Ultra ATA hard disk, so I power off the Mac.
I remove the SuperDrive DVD-ROM and I connect the hard disk in its place (I already made this with other ATA hard disks in past and it always was OK).
I close the Mac.
I try to start: nothing! The light on the power-on button of the Screen (Apple Cinema Display 20" plastic) and the light on the power-on button of the Mac case starts flashing 3 times (then stop, than other three times, etc...).
So I power off. I change the jumper configuration of the hard disk, like the Super Drive. I try again: NOTHING. Always three-times flashing the lights.
So I power off. I re-install the DVD drive, close the Mac again and restart it.
SURPRISE: the same symptom! The computer doesn't start and always makes the three-times flashing lights...
So I tried totally removing the DVD drive, and restarting it without it: nothing: same symptom.
Unfortunately I made these attempts forgetting to disconnect the power cable of the Mac!
Then I start trying with other RAM configurations, hoping that just a RAM module got burned. I have 6 ram modules (512 MB each).
I try lots of combinations... nothing, always same symptom.
Finally, I disconnect the power cord again, I re-install all the RAM modules, an I try to reset the CMOS: I remove the Motherboard battery for some seconds.
Than I re-install the battery, close the Mac, connect the power cord, restart it: it works!!!
I go in System Info, and I see that it doesn't recognize two of the 6 RAM modules: just 4. The slots of the other 2 not recognized DIMM modules seems empty, but there is the ram!
So I power off the Mac Again. I disconnect the power cord.
I change the RAM modules positions. I try again: nothing! Again the three-times flashing lights symptom, and always black screen again.
So I try again by removing the CMOS battery... nothing... always flashing...
After lots of attempts (also changing again the RAM positions, trying to remember how it was when it worked...)... nothing.
I power off the Mac.
After about an hour, I simply try to power on it... IT WORKED!!!
I used it too... went on Internet, etc... Finished working, I powered it off and went to bed.
The day after, I tried to power it on... nothing! Always three times flashing lights...
From that moment, it was totally impossible to let it work...
I tried to change the RAM positions again... I tried also pressing every time the reset button on the Mother Board... nothing...
The only different symptom that I obtained, a couple of times, was that the two lights (on the Screen button and on the Mac tower button) didn't flash, but was always on.... but it didn't run anyway: totally black screen.
How is this possible? Durin 18 years of computer hardware experience, NEVER happened that a computer got broken just removing and re-installing a DVD-ROM drive!
And I'd never imagined that removing a DVD-ROM could be a dangerous operation... It seems to me just like a car that got broken if I replace the cigarette lighter...
What do you think? how is this possible?
If the CPU or the Motherboard or the RAM too got broken... simply it NEVER should run... on the contrary two times it worked very well!... with a broken Motherboard or CPU??? ...mmmm... so strange....
If the RAM got broken... how is this possible? 6 ram modules burned together??? It seems so absurd... (in past there were 8 RAM modules... one or two got broken... so I removed them and it worked again... but not 6 !!!!).
Any opinion?
Any practical advice?
Prevision of costs?
Thank you!!!
Message was edited by: ununpentium

Hi Wolfman I have an update of the situation.
We tried moving the RAM modules again... and at one point it worked! With just 2 RAM modules.
But at the green screen (with the gray apple darker) it blocked.
So we removed the two RAM modules and installed other two modules: it worked again! These two last modules are 512 MB each.
So we restarted the system pressing "c" with the OSX DVD in the drive, and it worked! I used System diagnostic OSX utility and it found the 2 ram modules, but of 256 MB each instead of 512 !!! How is this possible? (if they were broken OK, but detect just half of its size seems so strange...).
Than we restarted it again connecting an OSX bootable external Fire Wire LaCie hard disk (FW400 port), and it worked!
We used DISK UTILITY to test the internal boot hard disk and it gave me an error (verify disk).
The Disk utility was unable to repair the disk.
Another damage!
I remember that in the past attempts it booted once (not three times flashing) and stopped at the grey screen... (I think: maybe due to the boot hard disk error!).
Unfortunately this external bootable firewire disk has got some problem and it sometimes blocks itself emitting a "clic".
So I powered the mac off and connected another newer firewire lacie bootable hard disk. I connected it in the FW800 port. I rebooted and... surprise: three times flashing light again!!!
No way to let it pass this wall, no initial "sound" again... nothing!
So I removed the FW800 drive, and changed the RAM again (inverted them, always two internal slots n. 1 and 2): it worked!
I booted from the FW400 hard disk, and it worked. I was able to backup some data from the internal hard disk (in order to be able to try to solve the error initializing it), and I tried again to boot with the FW800 hard disk (I want a stable system while initializing a drive!).
As I connected the FW800 hard disk again, I tried to reboot... nothing! Again the three-times flashing light error! No sound... black screen again...
(So, simply removing a DVD ROM I got RAM broken, maybe the Logic board, the hard disk too... maybe the FireWire 800 port too.... mmmm.... this mac is possessed! And it is connected through a professional power stabilizer too!).
So after several attempts with RAM, cmos reset, firmware reset (power it up holding the power on button for some seconds), etc... I got it working again...
So this time I rebooted it pressing "c" and I initialized the internal hard disk using the OSX DVD as boot drive...
Then I rebooted from the FW400 hard disk and I used CarbonCopyCloner to restore an internal hard disk clone OSX complete installation from a .dmg image file in the FW800 lacie hard disk... but this time I connected it not using the FW800 port but through the USB 2.0 port... and it was able to copy the data.
The computer was working... able to boot... no three times flashing error... no FW800 connections... always rebooting OK... the internal hard disk initialized, working, with NO errors (disk utility tested), made bootable...
I tried to reboot again (with no "c" or "alt" pressing, hoping the internal boot hard disk working again): nothing!
THREE TIMES FLASHING LIGHT AGAIN!!! No way to solve the problem now... always flashing...
What is happening here??? I don't understand! I use computers (instable DOS/Windows computers mainly!!!) form about 18 years... never seen a so strange behaviour!!!
We'll try to gather money to replace the RAM, before thinking to a Logic Board replacement...
Your opinion?
Thanks!

Why is there 526k in DVD-Rom?

The DVD-ROM Content field in the project is empty, but the screen says there is 526k used by DVD-Rom... why?
Is this an amount used by some sort of overhead?

Well, that 526k is clearly some kind of overhead... I created a new project with no assets (did nothing at all) and it shows the same 526k as already being used
So... I'll just ignore and get on with other work

CD/DVD-rom Issues; Won't Boot

   Hi, I am having a problem booting when I remove my CD-Rom 'Slave' or try to replace it with a DVD-Rom.
Below I will give my computer specs.
I have 2 hard drives, so the Primary IDE slots hold my 2 hard drives; one a
Master and the second one is the slave to the master.
On the Seconday IDE slots, I also have 2 cd-roms, one is the master and the
other is the slave to the master. The master is my cd/read/write cd-rom. I
want to leave it and change the slave cd-rom to a DVD-rom (not a dvd r/w
rom)...
I bought bestbuys dvd-rom, took out the 'slave' cd-rom and put the dvd-rom
in with the pin set for the slave. I booted my computer and it wouldn't boot
pass the first booting page. It wouldn't boot into windows.. What could be
wrong?????????
I took the new dvd-rom back out and left the secondary slave empty and tried booting and it
wouldn' t boot with nothing in the secondary cd-rom bay .. wierd to say the
least.. Like I said the secondary IDE slot is the Master of r/w cd-rom and I
never removed it or touched it, it is still there..
I then put my old cd-rom back in the secondary (slave) and waited a few
mintues and booted up my computer.. It booted with no problem.. I repeated
this whole sequence several times with the same results.. I for the life of
can't figure it out... My computer should boot with or without the second
cd-rom (slave), shouldn't it????? Adding a cd-rom or a dvd-rom should not keep my
computer from booting up should it?????
In my cmos, I have it set to boot-up with the hard drive as my first
boot-up, the second is the cd-rom.. but I don't see how removing or replacing
the 'slave' cd-rom would prevent it from booting into windows..
Yes, I have check the cables, settings and everything in my whole computer.
Can someone please tell me what is causing this.. I need a dvd-rom drive.
not paticularly the brand of the dvd-rom I just bought (which I have already
took back anyway) but I do need to get a dvd-rom asap in my computer so I am
hoping someone might know a solution to this problem..
Thanx for any help,
Granny (below are my specs)
SYSTEM INFORMATION:
Mother Board: K7N2 Delta series MS-6570 (v1.X) ATX Mainboard
AMD Athlon™ XP 2500+ 1.84 GHz, 2.00 GB Ram
OS Name   Microsoft Windows XP Home Edition
Version   5.1.2600 Service Pack 2 Build 2600
OS Manufacturer   Microsoft Corporation
System Manufacturer   NVIDIA
System Model   AWRDACPI
System Type   X86-based PC
Processor   x86 Family 6 Model 10 Stepping 0 Authentic AMD ~1837 MHz
BIOS Version/Date   Phoenix Technologies, LTD 6.00 PG, 11/7/2003
SMBIOS Version   2.3
NVIDIA GeForce 6800 GT Video card 256MB
System Directory   C:\WINDOWS\system32
Boot Device   \Device\HarddiskVolume1
Hardware Abstraction Layer   Version = "5.1.2600.2180 (xpsp_sp2_rtm.040803-2158)"
Total Physical Memory   2,048.00 MB (just updated my ram from 512 mb last week)
Available Physical Memory   1.59 GB
Total Virtual Memory   2.00 GB
Available Virtual Memory   1.95 GB
Page File Space   2.60 GB
Page File   C:\pagefile.sys
Power Supply 400 Antex (ATX12V)
Primary IDE
Master 40 GB Hard Drive
Slave 160 GB Hard Drive
Secondary IDE
Master CD-R/W Rom: TDK 52x EIDE
Slave to Master CD-R/W Rom: MTRP 50x EIDE
This is all it gave on the storage/ide under my system info;
Storage/IDE
Name   Standard Dual Channel PCI IDE Controller
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID PCI\VEN_10DE&DEV_0065&SUBSYS_57001462&REV_A2\3&13C0B0C5&0&48
I/O Port   0x0000F000-0x0000F00F
Driver   c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes),
Name   Primary IDE Channel
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID   PCIIDE\IDECHANNEL\4&26D47942&0&0
I/O Port   0x000001F0-0x000001F7
I/O Port   0x000003F6-0x000003F6
IRQ Channel   IRQ 14
Driver   c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes),
Name   Secondary IDE Channel
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID   PCIIDE\IDECHANNEL\4&26D47942&0&1
I/O Port   0x00000170-0x00000177
I/O Port   0x00000376-0x00000376
IRQ Channel   IRQ 15
Driver   c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes),

With the one drive alone did you remove the jumper?
Sometimes drives are picky and fight over who is master/slave. Try switching them.

My CD/DVD-rom drive won't read audio cd's

Since installing itunes on my laptop, the CD/DVD rom drive won't read audio cd's any more! However, it will read data CD's and dvds.
It didn't stop all at once...it started failing to read the odd random audio cd. Over time, gradually more and more CD's not recognised until no audio cd's readable at all!
When I say 'not recognised' I mean that if you look in the cd-rom file with a music disc inserted it thinks the drive is empty. The drive spins the disc a few times and then gives up. As only music cd's affected I suspect this is something to do with the itunes software. I've tried the various troubleshooting tips on itunes help but no joy....has anyone else had this problem / anyone know of a possible solution?
Thanks
Tiny

I had the same problem and I contacted a support team. They suggested that I upgrade my computer's power supply and I did. I had a 250W drive and now I have a 350W drive and it reads the CDs perfectly; except for one certain CD.

Naming DVD Rom Contents Folder

How do you control the name of this folder?
I seem to get 2 DVD Rom Folders 1 empty and one full?
Any advce appreciated.
Best WIshes
Tommy Banana

Sounds like you need to delete encoded assets from the advanced menu before burning this particular iDVD project so it doesn't default or use prior project assets (just a guess on my part).
Click Here
Try this first though:
drag and drop the plist for iDVD to the trash and empty the trash (then Restart the computer). Pref's look like this:
com.apple.iDvd.plist
(copy and paste the above item & please use the Finder to locate these pref's on your system).
(3) G4 PM's/(3) S-Drives/Sony TRV900/Nikons/6FWHD's/PS7/iLife06/FCPHD/DVDSP/etc. Mac OS X (10.4.8) My ichatav AIM account is: SDMacuser1 (Please use Text chat prior to video)

Mounting a Solaris x86 CD/DVD from a remote Windows CD/DVD-ROM drive

Greetings, all.
Is it possible to mount a remote Windows CD/DVD-ROM drive? I have the Solaris 10x86 Companion Software DVD sitting in a CD/DVD-ROM drive that's installed on a Windows server on my network. It is shared-out (F:) and the two servers can ping each other. I've also confirmed the NFS services/daemons are running on the Solaris x86 machine. I've tried the following variations but, all have failed to produce successful results:
# mount -F nfs x.x.x.x:/f /mnt
nfs mount: x.x.x.x: : RPC: Program not registered
nfs mount: retrying: /mnt
# mount -F hsfs x.x.x.x:/f /mnt
mount: No such device
mount: cannot mount x.x.x.x:/f
# mount -F hsfs x.x.x.x:/F /mnt
mount: No such device
mount: cannot mount x.x.x.x:/F
[FYI: S10_106_SOFTWARE is the DVD's label as reported by Windows Explorer.]
# mount -F hsfs x.x.x.x:/S10_106_SOFTWARE /mnt
mount: No such device
mount: cannot mount x.x.x.x:/S10_106_SOFTWARE
# mount -F hsfs x.x.x.x:/s10_106_software /mnt
mount: No such device
mount: cannot mount x.x.x.x:/s10_106_software
# mount -F nfs x.x.x.x:/S10_106_SOFTWARE /mnt
nfs mount: x.x.x.x: : RPC: Program not registered
nfs mount: retrying: /mnt
# mount -F nfs x.x.x.x:/s10_106_software /mnt
nfs mount: x.x.x.x: : RPC: Program not registered
nfs mount: retrying: /mnt
# mount -F hsfs x.x.x.x:/f/s10_106_software /mnt
mount: No such device
mount: cannot mount x.x.x.x:/f/s10_106_software
# mount -F hsfs x.x.x.x:/F/s10_106_software /mnt
mount: No such device
mount: cannot mount x.x.x.x:/F/s10_106_software
# mount -F hsfs x.x.x.x:/f/S10_106_SOFTWARE /mnt
mount: No such device
mount: cannot mount x.x.x.x:/f/S10_106_SOFTWARE
# mount -F hsfs x.x.x.x:/F/S10_106_SOFTWARE /mnt
mount: No such device
mount: cannot mount x.x.x.x:/F/S10_106_SOFTWARE
I've also tried mounting it at bootup by adding the appropriate entry in the /etc/vfstab file but, this does not work as well. I've tried Google'ing for an answer to my issue but, I haven't been able to find anything that applies directly to what I'm reporting. It's usually chatter about mounting from one UNIX server to another. Any advice from the community would be greatly appreciated.

After three weeks, you deserve a reply. Windoze does
not natively support NFS.Also deserves a decent answer...
There are two ways to do this:
Install Microsoft's free "Windows Services for UNIX," which includes a Windows NFS server; or
Install the 'sharity' package (google for it); it provides Solaris systems the ability to mount Windows shares

A305 - S6872 Laptop CD/DVD Rom does not show up on "My Computer"

How to I fix this problem. There's a "!" mark in the "Device Manager" for the cd/dvd rom drive.
"!" DR7164O OHV364L SCSI CdRom Device
"!" TSSTcorp CDDVDW TS-L633P
There's also a "!" on the networks adapters.
"!" Microsoft 6to4 Adapter
"!" Microsoft ISATAP Adapter #2
How do I fix these problems because updating the drivers will not fix it and make it go away.
if you can help, that would be great.

Satellite A305-S6872
See this Toshiba document..
CD / DVD drive missing from 'My Computer' (Windows Explorer)
-Jerry

I am programming a DVD-Rom in DVD Studio Pro 4 and need to display and open pdf files, any suggestions?

I am programming a DVD-Rom in DVD Studio Pro 4 and need to display and open pdf files, any suggestions?

http://documentation.apple.com/en/dvdstudiopro/usermanual/index.html#chapter=22% 26section=9%26tasks=true

Receive message after importing serveral songs from CD into iTunes (latest ver 11.1.5.5)... "Error occurred while converting the file 'songname'. The required folder cannot be found." CD/DVD ROM is no longer recognized until restart.

Consistently receive the following message after importing serveral songs from CD into iTunes (latest ver 11.1.5.5)...
"Error occurred while converting the file 'songname'. The required folder cannot be found."
CD/DVD ROM is no longer recognized until computer is restarted.

I have the same problem. I recently moved my music from a Vista PC to a new Laptop with an external CD drive. It will copy one song from the CD and it will show in the Music file and then I get the message ' Error importing a CD - Folder not found'. I must unplug the CD drive and plug it back in. I have seen no fix for this problem.

T60 no longer recognizes CD-RW / DVD ROM

so my T60 suddenly stopped recognizing the CD-RW/DVD ROM.
I have uninstalled and reinstalled and tried updating the drivers, but it keeps going into conflict in device manager.
I went into the Bios to try and test, but it isn't recognized there either.
What can be wrong with it. I have tried just about everything I know to fix it.
please help

Restart your computer, when you see the Thinkpad splash screen press the blue button. Go into the diagnostics and test the cdrom from there. Report back with the results.
T60 2623-D7U, 3 GB Ram. Dual boot XP and Linux Mint.
T400 2765-T7U Windows 7
Registered Linux User #160145
FYI: I am not employed by Lenovo

My acer 7535-5020 no longer recognizes my cd/dvd rom drive

My acer 7535-5020 no longer recognizes my cd/dvd rom drive-I am ready to scream! I cannot afford the tech prices as I am disabled but I cannot find anything to cure this sick puppy. Help please!!!

check inside BIOS whether your ODD can be detected, if cant be detected must be connection cable or HW issue
if still able to detect in BIOS, try to run basic troubleshoot regarding ODD
https://support.microsoft.com/en-us/kb/314060/en-us?wa=wsignin1.0

Hi after install win 8.1 on macbook i can't see dvd rom in my devices

hi
after i download new bootcamp and install new windows 8.1 pro i saw my dvd rom but after half an hour my dvd/cd rom removed and i can see this device in device manager.

Third-party NTFS software interferes with the Apple NTFS drivers, which control whether you can see the Bootcamp partition in the Startup Disk option. As a test, can you uninstall all third-party NTFS software and check System Preferences -> Startup Disk?

DVD-Rom drive in Satellite C655-S5128 not working properly in Windows 8

I recently upgraded my system from Windows 7 to Windows 8. However, the DVD-Rom drive after the upgrade no longer works properly -- it now treats the pre-recorded disk as if it was completely blank. I tried reinstalling the Toshiba Disc Creator, but that did not work.
Any solution?

You apparently did not use the Toshiba Upgrade Assistant in upgrading to Windows 8. See HERE for DVD and Disk Creator problems occurring during the upgrade and solutions.
C.B.
Toshiba Sat. C75D-B7260 Win 8.1 64 Bit--Toshiba Sat. L775D-S7132 Win 7 HP SP1 64 Bit and Win 10 PRO Technical Preview--Toshiba Sat. L305-S5921 Win Vista SP2 32 Bit

G3 Pismo DVD-ROM Problem

The DVD-ROM (Model M7931, Apple P/N 661-2244) in my G3 Pismo is not working properly. When a CD or DVD is input the drive spins, but makes slow & fast spin speed noises. Then it quits without reading the CD or DVD. The lens is clean & the drive appears in the System Profiler. When I replace the DVD-ROM drive with a CD-ROM drive (M73888), the CD drive reads a CD, so apparently the electronics within the G3 are OK.
I've read in forums that these drive have been problematic. Has anyone attempted a repair of the drive or know what might be the problem? The Service Manual troubleshooting doesn't suggest much, except replace. Since the drive is inop & possibly need to be trashed, I'm not adverse to trying to disassemble & attempt a repair. I can continue to use the CD-ROM drive.
I doubt that I will replace the DVD-ROM because used ones appear to cost $50+ & new ones about $100+. Is there an alternate (cheaper $) PC drive that could be used?
 Cheers, Tom

It's fixed. WD40 to the rescue.
I was considering swapping the Apple drive with a PC drive (see first link below, Plan B), but thought I would do a little troubleshooting (Plan A).
I opened the drive tray from it's enclosure. Using a #0 jeweler's Phillips screwdriver, I removed the metal cover plate screws (5). Then removed the screws (3) holding the motor/plate assembly. Carefully lifted the motor assembly upward at about a 45 degree angle (flex cables were attached). Looking at the side, there was about a 1mm gap between the motor & the plate. Using the plastic nozzle on a can of WD40, sprayed a small amount of lubricant. Let it sit for a few minutes & rotated the spindle. Reassembled everything.
I inserted a CD, didn't hear any spinning noise & the CD icon appeared on the screen. Repeated with a DVD. Both were being read. Yea!!!!!!!!!!!!
Found these helpful links when searching for a possible solution.
Replacing or Upgrading the Optical Drive in Your PowerBook G3 or 1400
http://lowendmac.com/rivera/06/0124.html
Replacement Pismo Drives
http://forums.macnn.com/69/powerbook-and-macbook-pro/223617/a-list-replacement-p ismo-optical/
Repairing or Upgrading of Optical Drives (CD,DVD,MO) for Laptops and Notebooks
http://repair4laptop.org/notebookoptical_drive_cd_dvdmo.html
 Cheers, Tom

DVD ROM Empty

Similar Messages

Maybe you are looking for