DVD unable to be verified

On my old macbook and on my NEW macbook i have not been able to verify a disc in finder. BUT if i use toast i don't have any problems.
I have used the internal dvd burner and an external, same message.
Also I have created a new user - same problem.
Done an archive and install
AND also done a disc utility repair under the install disc.
NOTHING is working. help!!!!

Finder: Burn started, Fri Jan 25 17:07:47 2008
Finder: Burning to DVD-R (MCC 03RG20) media with DAO strategy in HL-DT-ST DVDRW GSA-S10N BP10 via ATAPI.
Finder: Requested burn speed was 47x, actual burn speed is 8x.
Finder: Burn underrun protection is supported, and enabled.
Finder: Burn finished, Fri Jan 25 17:09:58 2008
Finder: Verify started, Fri Jan 25 17:09:58 2008
Finder: Discrepancy in block 283 at byte 79.
Finder: Source data: 0000 0000 0000 0200 0000 0000 0000 0500
Finder: Burned data: 0000 0000 0000 0200 0000 0000 0000 0300
Finder: Verify failed, Fri Jan 25 17:10:00 2008
Finder: Verify error: 0x80020063 Verification of the burn failed.
Finder: Burn started, Fri Jan 25 17:41:54 2008
Finder: Burning to DVD-R (SONY16D1) media with DAO strategy in HL-DT-ST DVDRW GSA-S10N BP10 via ATAPI.
Finder: Requested burn speed was 47x, actual burn speed is 8x.
Finder: Burn underrun protection is supported, and enabled.
Finder: Burn finished, Fri Jan 25 17:52:22 2008
Finder: Verify started, Fri Jan 25 17:52:22 2008
Finder: Discrepancy in block 283 at byte 79.
Finder: Source data: 0000 0000 0000 0200 0000 0000 0000 0500
Finder: Burned data: 0000 0000 0000 0200 0000 0000 0000 0300
Finder: Verify failed, Fri Jan 25 17:52:27 2008
Finder: Verify error: 0x80020063 Verification of the burn failed.
Finder: Burn started, Fri Jan 25 18:33:42 2008
Finder: Burning to DVD-R (SONY16D1) media with DAO strategy in HL-DT-ST DVDRW GSA-S10N BP10 via ATAPI.
Finder: Requested burn speed was 47x, actual burn speed is 8x.
Finder: Burn underrun protection is supported, and enabled.
Finder: Burn finished, Fri Jan 25 18:37:51 2008
Finder: Verify started, Fri Jan 25 18:37:51 2008
Finder: Verify finished, Fri Jan 25 18:37:53 2008
Finder: Burn started, Fri Jan 25 18:43:52 2008
Finder: Burning to DVD-R (SONY16D1) media with DAO strategy in HL-DT-ST DVDRW GSA-S10N BP10 via ATAPI.
Finder: Requested burn speed was 47x, actual burn speed is 8x.
Finder: Burn underrun protection is supported, and enabled.
Finder: Burn finished, Fri Jan 25 18:51:28 2008
Finder: Verify started, Fri Jan 25 18:51:28 2008
Finder: Discrepancy in block 283 at byte 22.
Finder: Source data: 0000 0010 0000 0801 0000 0000 0000 0000
Finder: Burned data: 0000 0010 0000 8700 0000 0000 0000 0000
Finder: Verify failed, Fri Jan 25 18:51:30 2008
Finder: Verify error: 0x80020063 Verification of the burn failed.
i cant type in the all messages because it's too long. it won't post.

Similar Messages

  • I'm trying to log onto app store, but I keep getting a message that my device or computer is unable to be verify. How do I verify it. However, when I use itunes, I have no problems in logging onto my account with the same apple ID

    I'm trying to log onto app store, but I keep getting a message the my device or computer is unable to be verified. How do I verify it when the app store will not allow me to log onto the account even when I use my Apple ID, which works with no problem on itunes. What is up and how do I correct it now!

    Check your mac's Serial Number.
    Some people have problems with missing serial numbers on their Macs and that's the message you get when this happens.
    Click on the Apple at the top left of the screen, open "About this Mac" and click on "More Info". You should see a list with information about your Macbook Air. Check that on the Serial Number field you have your Mac's Serial. If you have "SystemSerial#" written instead then that's your problem.
    You can re-enter your serial number if you have a USB CD drive, it's not very straightforward but I can walk you through it if you need it.
    Cheers

  • I inserted what I thought was blank DVD-R/W to verify.  It won't eject.

    I inserted what I thought was a blank DVD-R/W to verify.  It won't eject.
    I have an appointment for tomorrow in the evening to remove DVD-R/W disc at the Grove in L.A.
    Phone support declined to assist without $19.00 charge.

    Restart the computer and hold the trackpad until the dvd is ejected.
    Best.

  • Unable to read burned dvd, unable to format dvd, and unable to burn dvd

    Unable to read burned dvd, unable to format dvd, and unable to burn dvd with my HP G62-339WM Notebook PCI have been unable to perform the Windows back up for months without using new discs. But even after using new discs Windows backup tells me that the disc that I previously used that it is asking to insert is not formatted. I also have not been able to read any dvds that I previously burned, instead it will sometimes recognize them as blank and they are not.  I also cannot perform a format on new dvd discs nor burn to them. I have been able to read some previously burned discs on another pc but not the discs that were created with Windows backup. I have tried everything. I have uninstalled the device, ran the fix it, tried troubleshooting, checked the registry and could not find the upper and lower filters listed. I am however able to read program software and the autorun pops up. Once in a while the autorun will pop up when a blank disc is inserted but then that is all the further I am able to use it. I don't know what else to do. I really want to be able to at least burn files to back up so that they are not lost forever. Please help!

    Fixed it myself - for some reason the La Cie refused to read the media. Had to use another machine to pull the data from the drive, copy it over the network to my iMac and then mount the ISO image.

  • Recording on DVD - "Unable to recover TOC" error

    Hi all
    Whenever I try to record on a DVD a face "Unable to recover TOC"
    I've tried to change the recording speed but no use.
    When I go to DVD properties and click on enable recording it does not recognize the DVD or any other CD in the drive.
    Please some help

    Hi,
    1. What software do use to burn cd/dvd disks? Try to use Nero, Ashampoo burning studio, Alcohol CD and DVD Burning Software,
    2. Then, I advise you to use high quality medias as TDK or Verbatim.
    3
    Go to device manager and remove the CD/DVD drive from the device list.
    Then access the registry and remove the Upperfilters and Lowerfilters values completely from the following registry key:
    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class{4D36E965-E325-11CE-BFC1-08002BE10318}
    Reboot the notebook and wait until the CD/DVD drive would appear again
    If you still have problems, maybe there is a problem with your cd/dvdrom

  • After failed installation from DVD unable to uninstall to retry - Error message 2343

    Having started installation of Elements 12 from DVD it failed before completing the installation and then rolled back the last two items on the installation list (out of 3). Now when running the DVD again it endeavours to do an uninstall before trying a reinstall. However it is unable to complete the uninstall process and fails every time with the Error 2343 - specified path is empty. Suggested options such as deleting temporary files and doing a clean boot produce exactlly the same result. This is on a Windows 7 Pro x64 PC with 8GB RAM and an i3 processor and 500GB disc with over 200GB free. It would seem that the only solution to remove the software is to edit the registry, as the standard uninstall process is clearly not going to complete. I therefore need to know what registry edits are needed in order to remove the programme complately from the PC. Otherwise it is clear that it is never going to be possible to install the software, which makes it rather a waste of money!

    I had already tried that I'm afraid, without success. I therefore tried the installation on a different PC, also Windows7 Pro x64 but with different hardware (AMD proc., different disk controller and different DVD ROM but also with 8GB RAM and plenty of available disk space). The only other common parameter to note is that both PCs are running Bitdefender antivirus software. However I allow the AV software to completely check the Photoshop Elements 12 DVD ROM before starting the install process, as this can take severla minutes, so that the AV software does not need to access the DVD ROM drive during the install process. The software installation failed during the installation of the Shared Technologies scetion exactly as on the previous PC. I can only conclude that either there is a problem with Windows 7 Pro x64 or Bitdefender compatibility and that it will not be possible to install this software on either of these PCs in its current form. There has to be a limit as to how much time one is willing to spend on overcoming an incompatibility like this. I think I will have to find an alternative photo editing product (the Serif trial product seems to load without any problems on the original PC!). Thank you anyway for your help and suggestions but I think in this case we have hit a brick wall.

  • Why do my dvd burns fail to verify

    Several attempts to burn dvds have resulted if failures to verify. It seems to burn fine, but will not verify and tells me the disk may be unreliable. I am using Delkin Devices Archival Gold DVD-R discs. Burned at both x6 and x8. The first 6 or so burned and verified fine, but the last 4 have not been verifyable. Any thoughts?

    There could be several reasons:
    iMac Superdrives are extremely finicky - mine only likes Verbatim for instance. So you might want to try a different brand; another way to get consistent good burns is to burn slowly - I set mine at the slowest speed available; I'd rather wait a few more minutes. I also do not do anything else during the burn process (and turn off screensaver/sleep). And, the drives are not sturdy desktop models, they get hot - so I would not burn more than two at most and then let it cool down for at least 15 - 20 minutes. For all of the above reasons, I usually use a desktop sturdy tray loaded burner which just works. But, even using the internal, I've never had a coaster.

  • HP System Recovery DVD Unable to Complete Recovery

    Hello
    I am having trouble using the System Recovery DVDs on my HP Pavilion dm4-1065dx. My computer got a virus and I uninstalled Windows 7 and reinstalled it using a new copy I bought.  Currently my computer can run Windows 7 but it does not have any programs or other software installed on it. I am trying to restore my computer to factory settings using the System Recovery DVDs from HP. The DVD works until it gets to the step where it must restore files to the hard drive. About 10% into this step a message pops up that says:
    "Contact HP Support
    In most cases, recovering the hard drive will fix your problems.
    If your problems continue, you may need to contact HP Support. Find HP Support contact information in your PC documentation."
    I have tried running the System Recovery DVDs several times and always get this message. So far I have been unable to recover my hard drive and try this process again.  
    Any tips?
    Thanks

    Hello
    I am having trouble using the System Recovery DVDs on my HP Pavilion dm4-1065dx. My computer got a virus and I uninstalled Windows 7 and reinstalled it using a new copy I bought.  Currently my computer can run Windows 7 but it does not have any programs or other software installed on it. I am trying to restore my computer to factory settings using the System Recovery DVDs from HP. The DVD works until it gets to the step where it must restore files to the hard drive. About 10% into this step a message pops up that says:
    "Contact HP Support
    In most cases, recovering the hard drive will fix your problems.
    If your problems continue, you may need to contact HP Support. Find HP Support contact information in your PC documentation."
    I have tried running the System Recovery DVDs several times and always get this message. So far I have been unable to recover my hard drive and try this process again.  
    Any tips?
    Thanks

  • Mozilla Unable to Locate verify.dll and crashes

    I'm running Mozilla 1.7.11 on Windows NT. In the last few days, Mozilla will crash any time I visit a site that uses certain types of javascript. The error message that pops up before crashing has the title "mozilla.exe - Unable to Locate DLL" and reads " The dynamic link library verify.dll could not be found in the specified path", and then it proceeds to list several paths, including system folders, mozilla folders.
    I haven't modified my computer's settings, and it seems to be free of spyware. Is there a particular Java download on this site that I should simply install and re-run to replace or update the verify.dll file? Or should I manually try to find the file online and upload it somewhere to my PC?

    Beats me. However, here is some ideas:
    I suggest upgrading Mozilla to the latest version. It might automatically download the verify.dll file. If not, delete Mozilla and reinstall the lastest Mozilla version from scratch. If you reciently installed Microsoft Vista, it appears that the verify.dll may have been left out, therefore download verify.dll off the web and install it where it says, dont have to reinstall Mozilla. Good luck!

  • RE: CD/DVD Unable to read or write -Thinkpad z60 m

    My operating system is Windows 7  my CD/ DVD ROM does not read nor writes any type of media, I have exhausted and implemented all the possible solutions I've gotten from the different forums but with no success. I ran the hardware test by PC Doctor on the Thinkvantage Toolbox and I the following test result : Unable to start the drive - SCSI Error 0904H. Does anybody have any solution for this problem?
    Thank you
    Maghid49

    To malossi:
    You dont have the similar problem because the user above cannot read and burn ONLY the original DVD movies!
    > i am able to boot from dvd, read dvd data, burn cd but, unable to read or burn film data (original);
    In your case possibly the drive is dead or not compatible with the media (but I dont think so).
    Check this Microsoft site for some general ideas:
    http://support.microsoft.com/kb/321641/en-us
    I have read also that someone was having this problem, and found that going into hardware profiles for the CD Rom that wasn't reading, clicking on the advanced tab, and selecting "PIO only" instead of "DMA if Available" worked in win XP sp2. Maybe you will try these.

  • Optiarc DVD and external DVD unable to read discs?

    I am trying to burn an Ubuntu DVD. Unfotunately, either if I introduce a DVD in the in-built Optiarc unit of my iMac or in an external DVD recorder, the iMac seems unable to execute the task correctly.
    If I try to use the Disk Utility, the "Burn" button is not present.
    If I use a different software, uch as Burn.app, the disk is toaast, but the iMac says it is unable to read the disk content.
    Btw, I have downloaded the correct iso file of Ubuntu.
    Any possible help?
    Thanks

    17 months later... Any solution ?
    I have got the same issue : I can read all CD-ROMs but not DVD (any DVD)
    Same result using internal Superdrive and external DVD reader (both USB and FireWire).
    iMac 27'  / 3.33GHz Intel Core 2 Duo
    OPTIARC DVD RW AD-5680H (3AHB) - ATAPI
    Mac OSX 10.8.4 (12E55)
    OSX Mountain Lion reinstalled and all updata applied
    Test with different accounts, including a root account
    Thanks

  • DVD burn fails on verify consistantly, unless you boot from another disk...

    Guys,
    I have a dual G4. Always seemed to be able to burn a DVD. Now, Popcorn, disk utility and toast all fail verify for DVD burns.
    If I boot from my backup disk and burn using popcorn, toast or disk utility it burns and verifies fine. Both are Tiger 10.4.8, one has many things installed, the back up drive has few things.
    It seems to exonerate the hardware and my verbatim media.
    Any ideas?
    John
    G4 dual 1ghz   Mac OS X (10.4.8)   original DVD drive

    Hi
    It sounds as if it may be lack of free disk space, or lack of contiguous free disk space. How much do you have left on your main drive? Perhaps deleting some unwanted files would help.
    If your drive is highly fragmented the DVD image may be scattered all over the disk, causing a buffer underrun, especially if you're running the burning software off the same drive. You can buy software to defragment it, although OS X defragments small files on the fly so it's not normally needed. Perhaps burning at a slower speed would give the drive time to keep the buffer full. Freeing up some disk space should also help though, so there's more contiguous free space available

  • DVD-R Burning - Not Verify Correctly

    I'm having troubles burning a simple data DVD-R on my iMac. I've tried many times, but I keep getting this error message:
    "Burn
    This disc did not verify correctly and is unreliable. Because this disc is unreliable, discard it and try again using a new, blank disc. (Error code 0x80020063)"
    If I go into Disk Utility and use Verify Disk on the DVD-R I burnt I get a different error message:
    "First Aid failed
    Disk Utility stopped verifying "Backup August 2007" because the following error was encountered:
    The underlying task reported failure on exit"
    What's that all about? Is it just that this particular DVD-R is crappy quality, or is there a more serious problem going on?

    Hi, sometimes certain makes of DVD & the macs are not compatible although they should be! I use a free App -> SimplyBurns it seems to be a tad more compatible.
    http://simplyburns.berlios.de/
    In addition, I only buy TDK or Sony CD & DVD's...L

  • One step DVD unable to capture video

    I have made many movies using one step dvd in the past. For some reason, now I get a message "Nothing Captured" "No video has been captured" when I try to create a new dvd from my video camera. I used the same camera and connection cords on another apple and it worked fine. It worked fine on this computer in the past. Any ideas?
    Thanks

    Bengt;
    Good ideas but I have checked each of those items. My camera is set to play, the tape works and I am using my firewire cable. The strange thing is I did everything exactly the same on a different apple computer and it copied the tape to the DVD with no problem.
    Thank you for thinking about my problem.

  • Installation software from app store unable to be verified.

    I received the following error when trying to install OS X MAVERICKS today.
    "This copy of the software Install OS X Mavericks can not be verified. It may be damaged or manipulated during download."
    I removed the downloaded file and downloaded it again from app store and tried to install it again but got the same error message appeared.
    The version is for Swedish so the message above is a translation of the error message. I have an IMAC 11.2 using OS X 10.6.8 which is supposed to be compatible with the update.
    Any suggestions on what to do is highly appreciated?
    Cheers!

    Usually indicates that you're Internet connection isn't the best and the file's getting corrupted. Best is to visit an Apple repair station and see if they can provide the installer. Next, try from a different location or a friend's connection.

Maybe you are looking for