DW Extract error: could not load Extract panel

How do I get my extract panel to work? I get and error message in the extract panel that reads, "Couldn't load the Extract panel. Try reloading the panel after sometime (Flyout menu>Creative Cloud Assets).

Hi Deziner1978,
Please try sign out from Dreamweaver Help -> Sign out(Your Adobe Id)
and then try re launch of Dreamweaver and again sign in using your Adobe Id.
Hope this resolves your issue.
Thanks,
Lalita

Similar Messages

Why do I get "error code 3: Could not load front panel" when I run my executable.

I have a LV 8.5 VI that controls only an agilent spectum analyzer. The agilent VIs call DLLs rather than SCPI commands. I created an application and an installer to load on a non LV machine and ran setup which was successful. When I run the EXE I get "error code 3: Could not load front panel" for each of my agilent spectrum analyzer VIs. I have to click "OK" about ten times, once for each VI. (My executable runs fine on all machines that have labview 8.5) The front panel does load with a broken arrow. The errors listed when the arrow is clicked for all of the Agilent VIs state: Missing subVI AGE444xInitialize.VI (or close.VI or read.VI etc.)
There is an AGE444x32.DLL in the data folder with the EXE file so I included as support both the DLL and all of the agilent drivers in the application build. Still no luck. I have built the application and installer about 6 times in various forms. I NEED AIR SUPPORT.
Unfortunately I do not have access to the internet at my jobsite so bear with me.
Rob

Hi V-rob,
I'm glad to hear the executable is working now that NI-VISA is installed. Thanks for posting the solution!
Jennifer R.
National Instruments
Applications Engineer

How to handle LabVIEW Error 3: Could not load front panel

I was working on an application, running a vi when the computer turned off. It took me a little time to start the computer again (is not an old computer, is a P4, 1GB, ABIT IG7 MotherBoard). After I unplugged and plugged the Power Unit it was possible to start the computer, before starting, it says that a CPU problem occured and press F1 to continue. Afer press F1 Windows started normally. Then I tried to open the vi in which I was working when the problem occured and LabVIEW says:
LabVIEW: Resource not found.
An error occurred loading the vi.
LabVIEW load error code 3: Could not load front panel.
The question is, can I open my vi someway or I just lost it?
I will really appreciate your answers since I have been working for a long time in this vi.

Well, I'm faced with this problem now. VI started its life as a 9.01 LV 2009/Vision 2009 on a given machine. Copied to another machine wth 7.1, 8.2 and 9.01 on it. Opened with 2009, saved it for 8.0. Opened it with 8.2, saved it for 7.1. Opened it with 7.1//Vision 7.1.1, edited it, saved. File appears to be fine.
Now trying to open it with either 8.2 or 2009 (9.01) fails with error code 3. Note that it still opens with 7.1, so the front panel is there. Anyway to fix this?

LabVIEW error code3: Could not load front panel.

Hi
I am getting second time the "LabVIEW error code3: Could not load front panel." when working with the development environment of LabVIEW 2009 SP1.
It is really annoying as I loose time as I have to revert to saved previously code.
Does anybody know where it may be coming from and how to avoid it?
Thanks
Pawel
Solved!
Go to Solution.

Pawel,
the panel has an origin which you can see in your VI:
Every element will be placed in a position in regard to this origin:
The position has a limit in regard to the bound. I am not sure about the value, but it should be around -35k...35k (or the double of it)....
hope this helps,
Norbert
CEO: What exactly is stopping us from doing this?
Expert: Geometry
Marketing Manager: Just ignore it.

Could not load front panel

I was given an application by a hardware vendor (a test program for their device) that was built via Labview (I have only the .exe). When I try to start it, I get a bunch of "could not load front panel" errors, all of the form:
LabVIEW: Resource not found.
An error occurred loading VI '[x].vi'. LabVIEW load error code 3: Could not load front panel.
[x] is the only difference among the four errors I get, where [x] is:
* NI_AAL_Pro.lvlib:Unwrap Phase.vi
* NI_AAL_Pro.lvlib:Real FFT.vi
* NI_AAL_Pro.lvlibcaled Time Domain Window (DBL).vi
* NI_AAL_Base.lvlib:Mean.vi
Basically every post I can find on ni.com about "could not load front panel" suggests that this is a build-time problem, i.e. that the developer forgot to check a box that would force the missing components to be included, which doesn't help unfortunately... but here's the twist: when I move this to another machine, it works fine. I don't have LabView installed on either machine. Both are Win8.1 x64. I believe the application was built with LabView 2010.
The only relevant difference between the machines that I can think of is that on the machine where the application *doesn't* work, I use many National Instruments device and have installed DAQmx. You'd think that if anything, that would install missing components and make this *less* likely to happen.
Since encountering this problem, I've tried to install every Labview 2010 runtime SP/patch I could find, but unless I'm missing something, there's not really a definitive place I can do to make sure I have all the patches or get a single cumulative rollup.
Any ideas? I don't have access to LabView or the source .vi, but the fact that it works on a second machine suggests there's hope. I really want it to run on my primary machine, where all the relevant hardware is.
Thanks!
-Dan

Is it possible that one machine only has the minimum run time engine (~42MB) installed? You need the full standard version (~180MB).
LabVIEW Champion . Do more with less code and in less time .

Preference Error: Could not load sharing preference pane

For some reason my second computer (iMac 27) is no longer showing up on the left pane of any finder window on my MBP. The iMac is running Yosemite and the MBP is running Mavericks. So I open System preferences to see if there is a problem with "Sharing" on the MBP. I'm getting a Preference Error: Could not load sharing preference pane. Do I need to install the update to fix this? I'm not ready to commit to Yosemite completely. I build apps for iOS and Mac and really need to test in both OS environments.

Do a backup.
Quit the application.
Go to Finder and select your user/home folder. With that Finder window as the front window, either select Finder/View/Show View options or go command - J. When the View options opens, check ’Show Library Folder’. That should make your user library folder visible in your user/home folder. Select Library. Then go to Preferences/com.apple.systempreferences.plist. Move the .plist to your desktop.
Restart the computer, open the application and test. If it works okay, delete the plist from the desktop.
If the application is the same, return the .plist to where you got it from, overwriting the newer one.
Thanks to leonie for some information contained in this.

ERROR Could not load style sheet: custom.css

Hi i am working with ADF faces.I had used selectors to change the skin.I put all the selectors in custom.css file.And i put the folder in the webcontent folder.
Like Skins/Ex/custom.css.
And here is the content of my adf-faces-skins.xml file
<?xml version="1.0" encoding="ISO-8859-1"?>
<skins xmlns="http://xmlns.oracle.com/adf/view/faces/skin">
<skin>
<id>Ex.desktop</id>
<family>Ex</family>

<render-kit-id>oracle.adf.desktop</render-kit-id>
<style-sheet-name>custom.css</style-sheet-name>
</skin>
</skins>
And adf-faces-config.xml content is
<?xml version="1.0" encoding="windows-1252"?>
<adf-faces-config xmlns="http://xmlns.oracle.com/adf/view/faces/config">
<skin-family>Ex</skin-family>
</adf-faces-config>
Now my problem is my application could't recognize the stylesheet.
And while i run the application i am getting the output which is using the Simple skin.......And in the log file it showing the error like
2006-11-09 14:18:58.125 ERROR Could not load style sheet: skins\Ex\custom.css
So anybody could help me in finding out the error.......Hope so..........
Thanks.......
simmi

I am sorry
Here is the content of my adf-faces-skins.xml file
<?xml version="1.0" encoding="ISO-8859-1"?>
<skins xmlns="http://xmlns.oracle.com/adf/view/faces/skin">
<skin>
<id>Ex.desktop</id>
<family>Ex</family>

<render-kit-id>oracle.adf.desktop</render-kit-id>
<style-sheet-name>skins\Ex\custom.css</style-sheet-name>
</skin>
</skins>

Preferences error - could not load displays preference pane

My screen resolution changed during game play. Now that the game is off, I cant change it back. This is what the error message says "Preferences Error - Could not load Displays preference pane."

Please read this whole message before doing anything.
This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it.
Step 1
The purpose of this step is to determine whether the problem is localized to your user account.
Enable guest logins* and log in as Guest. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
While logged in as Guest, you won’t have access to any of your documents or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this behavior; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
Test while logged in as Guest. Same problem?
After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
*Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
Step 2
The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Please take this step regardless of the results of Step 1.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of Steps 1 and 2.

Preferences error: Could not load Accounts preferance pane.

When trying to access my accounts tab under system preferences, it does the usual "must restart system preferences" fiasco to boot into 32-bit mode. After it relaunches, it displays an error message:
*Preferences Error:*
Could not load Accounts preference pane.
I've searched the apple support forums, google, insanelymac, and have not come up with a solution. So far, I've tried:
-Deleting the system preference... preference under account -> library -> preferences -> com.apple.systempreferences.plist
-Under system -> library -> preferencepanes I am running version 3.0 of Accounts.prefPane
-I have booted from the system disk and repaired permissions along with disk
-I tried restoring an older version of Accounts.prefPane from my time machine back-up, and I receive the same error. (this did not happen in 10.5.8)
Any help is appreciated. It's rather important that I access my accounts tab, haha. If worse comes to worse, I'll just wipe my entire system and do a fresh install. (something I'd rather avoid.) For the record, I did do a simple install of Snow Leopard instead of a clean install.
Cheers!

Hello Mr:
When trying to access my accounts tab under system preferences, it does the usual "must restart system preferences" fiasco to boot into 32-bit mode. After it relaunches, it displays an error message:
Preferences Error:
Could not load Accounts preference pane.
I have never seen that nor did I experience it myself.
Before you do an erase and install (there is no +"clean install"+ in Apple parlance), I would reinstall OS X 10.6 (over your current installation). Frankly, the message makes no sense (I am not suggesting it did not happen).
Barry
Message was edited by: Barry Hemphill

Error : Could not load com.sap.ip.bi.rig.Format in WAD 7

Hi,
Given config to be as below:-
ABAP Stack - BI 7 EhP1 SP3
Java Stack - BI 7 SP Level 19
while I try to implement the Format Cell option using Analysis Web Item modification in WAD 7.0, I get the below error
Could not load com.sap.ip.bi.rig.Format
Plz. suggest what is the correct config that supports the above implementation.
Thanks,
Priya

Thanks for reply,
I have seen the post, But my problem is that, while executing WAD.
could not load module com.sap.ip.bi.rig.format error is coming.
i think if these error is removed , coloring the backgroud will work via module com.sap.ip.bi.rig.format.
I shall be thankful to you for this.
Regards
Pavneet Rana

I am getting a photoshop error could not load photoshop because the preferences file was invalid and cln't load actions because of an unexpected end of file encountered.

I am getting a photoshop error could not load photoshop because the preferences file was invalid and cln't load actions because of an unexpected end of file encountered.

Are you trying to open Photoshop directly, or open it by double clicking on a Photoshop document, like a PSD file? If the former, then you might need to reinstall. Resetting Preferences would be the firs step, but I am not sure if that will work if Photoshop is not opening in the first place.
Try doing so anyway. Hold down Shift Alt Ctrl (Shift Opt Cmd) while opening Photoshop. OK the message to delete Preferences.
If you get the unexpected end of file error while trying to open Photoshop via a PSD document, then there is more than a good chance that that file is toast.
If still stuck, we need to know Operating System, and Photoshop version.

Preferences Error - Could not load Network

My dad just bought me a (used)) iBook g4 to replace my old one. It's running 10.3.9. It didn't come with a wireless card, so I ordered an Airport Extreme and installed it. I'm pretty sure I installed it correctly, I heard all the right clicks.
It booted up afterwards and the first thing I did was to run system update and try to get everything up to date. There were a ton. After it restarted, it no longer was connecting to our wirelesss network. I tried to go to System Preferences > Network and it responds with the error message "Preferences Error - Could Not Load Network" and nothing opens. Not to mention my DVD Player no longer works!
I have no idea what's at fault here- the airport extreme card, a bad update... And no idea how to fix it! Any help would be appreciated!

That it is not recognizing the retail (thanks cornelius) Leopard DVD is a problem indeed.
It should be plugged into the mains power, as the CD/DVD drive uses a lot of power when it is spinning.
Back to your About this Mac, does it mention that your optical drive can read DVDs?
On mine this info is located down the list under ATA which will have mentioned, CD
and in detail in the lower window
eg. Drive type: CD - RW/ DVD - ROM
if it shows the DVD-ROM part, that indicates it can read DVDs.
If it should be able to, then I wonder if the iBook's optical drive is OK. I could suggest loading another DVD into it, but you say DVD Player.app is missing.
What you could try is buying from a computer shop a CD drive cleaning kit, and following the instructions, run that through it. That is a fairy inexpensive exercise.
If it still does not recognize the DVD, and you had another Mac that you could connect by Firewire Target Disk mode, you could try installing leopard on it that way. But before that rather complex arrangement, try the disk cleaner. It might be a quick fix.

Error: Could not load file or assembly 'Microsoft.Activities, Version=1.0.0.0

Hi,
I am using VS 2012 to create custom sequential workflows (2010 model). The workflows created in VS 2010 are working fine, but the workflow created in VS 2012 is throwing the error.
When the workflow is run, I am getting the below error:
Error:
Could not load file or assembly 'Microsoft.Activities, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35' or one of its dependencies. The system cannot find the file specified.
Stack Trace: at System.Reflection.RuntimeAssembly._nLoad(AssemblyName fileName, String codeBase, Evidence assemblySecurity, RuntimeAssembly locationHint, StackCrawlMark& stackMark, IntPtr pPrivHostBinder, Boolean throwOnFileNotFound, Boolean
forIntrospection, Boolean suppressSecurityChecks) at System.Reflection.RuntimeAssembly.InternalLoadAssemblyName(AssemblyName assemblyRef, Evidence assemblySecurity, RuntimeAssembly reqAssembly, StackCrawlMark& stackMark, IntPtr pPrivHostBinder, Boolean
throwOnFileNotFound, Boolean forIntrospection, Boolean suppressSecurityChecks) at System.Reflection.Assembly.Load(AssemblyName assemblyRef) at System.Workflow.Activities.Rules.SimpleRunTimeTypeProvider.get_ReferencedAssemblies() at System.Workflow.Activities.Rules.RuleValidation.DetermineExtensionMethods()
at System.Workflow.Activities.Rules.RuleValidation.get_ExtensionMethods() at System.Workflow.Activities.Rules.RuleValidation.GetNamedMethods(List`1 targetTypes, String methodName, BindingFlags methodBindingFlags) at System.Workflow.Activities.Rules.RuleValidation.ResolveMethod(Type
targetType, String methodName, BindingFlags methodBindingFlags, List`1 argumentExprs, ValidationError& error) at System.Workflow.Activities.Rules.MethodInvokeExpression.Validate(CodeExpression expression, RuleValidation validation, Boolean isWritten) at
System.Workflow.Activities.Rules.RuleExpressionWalker.Validate(RuleValidation validation, CodeExpression expression, Boolean isWritten) at System.Workflow.Activities.Rules.RuleValidation.ValidateConditionExpression(CodeExpression expression) at System.Workflow.Activities.Rules.RuleExpressionCondition.Validate(RuleValidation
validation) at System.Workflow.Activities.Rules.RuleConditionReference.Evaluate(Activity activity, IServiceProvider provider) at System.Workflow.Activities.IfElseActivity.Execute(ActivityExecutionContext executionContext) at System.Workflow.ComponentModel.ActivityExecutor`1.Execute(T
activity, ActivityExecutionContext executionContext) at System.Workflow.ComponentModel.FaultAndCancellationHandlingFilter.Execute(Activity activity, ActivityExecutionContext executionContext) at System.Workflow.ComponentModel.ActivityExecutorOperation.Run(IWorkflowCoreRuntime
workflowCoreRuntime) at System.Workflow.Runtime.Scheduler.Run()
How to fix this?
Thanks

Hi,
The machine in which the workflow was created is different from the machine it is deployed.
Which dll should be available? Is the dll not part of SharePoint 2013?
Is this part of workflow Manager?
Thanks

Error could not load RoboHelp.

I start a excisting project up in RoboHelp Word. When I try
to open a topic I always recieve this error message:
Could not load RoboHelp. Re-install RoboHelp if you continue
to get this message. Error could not load RoboHelp. The problem is
that I have re-installed RoboHelp and also tried to install it into
my other computers but no luck.
Suggestions??????

Did you install it with admin rights attached to your login?

Preferences error: Could not load preference pane

Many times, when I attempt to load a Preference Pane, I receive the error message: "Preferences Error: Could not load [X] preference pane.” Clicking “OK” and reopening the preference pane succeeds.
Does anyone know what's going on here? I upgraded to Yosemite from a Snow Leopard installation, which I assume is part of the problem.
Using OS X 10.10.1, 2008 iMac

No dice.
Here's my EtreCheck report, if that helps anything:
EtreCheck version: 2.1.2 (105)
Report generated December 10, 2014 at 11:05:35 PM CST
Hardware Information: ℹ️
iMac (20-inch, Early 2008) (Verified)
iMac - model: iMac8,1
1 2.66 GHz Intel Core 2 Duo CPU: 2-core
4 GB RAM Upgradeable
BANK 0/DIMM0
2 GB DDR2 SDRAM 800 MHz ok
BANK 1/DIMM1
2 GB DDR2 SDRAM 800 MHz ok
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
ATI Radeon HD 2600 Pro - VRAM: 256 MB
iMac 1680 x 1050
System Software: ℹ️
OS X 10.10.1 (14B25) - Uptime: 0:54:22
Disk Information: ℹ️
Hitachi HDE721064SLA360 disk0 : (640.14 GB)
S.M.A.R.T. Status: Verified
EFI (disk0s1) <not mounted> : 210 MB
Jane's Brain (disk0s2) / : 627.01 GB (88.82 GB free)
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
eDrive (disk0s4) <not mounted> : 12.13 GB
USB Information: ℹ️
Apple Inc. Built-in iSight
Mitsumi Electric Hub in Apple Extended USB Keyboard
Mitsumi Electric Apple Optical USB Mouse
Mitsumi Electric Apple Extended USB Keyboard
Apple Inc. iPhone
Newer Tech miniStack Classic 320.07 GB
S.M.A.R.T. Status: Verified
EFI (disk1s1) <not mounted> : 210 MB
Jane's Old Brain (disk1s2) /Volumes/Jane's Old Brain : 319.73 GB (13.24 GB free)
Western Digital My Passport 0740 500.07 GB
S.M.A.R.T. Status: Verified
SylerNet Adjunct (disk2s1) /Volumes/SylerNet Adjunct : 269.14 GB (63.71 GB free)
ADJUNCT FAT (disk2s2) <not mounted> : 230.93 GB
Apple Inc. BRCM2046 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Computer, Inc. IR Receiver
Gatekeeper: ℹ️
Anywhere
Kernel Extensions: ℹ️
/Applications/Laucher from Herbie/Tools/Hardware/TemperatureMonitor.app
[not loaded] com.bresink.driver.BRESINKx86Monitoring (9.0) [Support]
/Applications/Porthole.app
[not loaded] com.Cycling74.driver.Soundflower (1.6.6 - SDK 10.6) [Support]
/Applications/Utilities/DiskWarrior.app
[not loaded] com.alsoft.Preview (4.1) [Support]
/Library/Application Support/VirtualBox
[loaded] org.virtualbox.kext.VBoxDrv (4.3.20) [Support]
[loaded] org.virtualbox.kext.VBoxNetAdp (4.3.20) [Support]
[loaded] org.virtualbox.kext.VBoxNetFlt (4.3.20) [Support]
[loaded] org.virtualbox.kext.VBoxUSB (4.3.20) [Support]
/Library/Extensions
[loaded] com.globaldelight.driver.BoomDevice (1.3 - SDK 10.9) [Support]
/System/Library/Extensions
[not loaded] com.palm.ClassicNotSeizeDriver (3.1) [Support]
Problem System Launch Agents: ℹ️
[failed] com.apple.CallHistoryPluginHelper.plist
[failed] com.apple.CallHistorySyncHelper.plist [Details]
[failed] com.apple.cmfsyncagent.plist [Details]
[failed] com.apple.coreservices.appleid.authentication.plist [Details]
[failed] com.apple.EscrowSecurityAlert.plist [Details]
[failed] com.apple.recentsd.plist [Details]
[failed] com.apple.SafariNotificationAgent.plist
[failed] com.apple.scopedbookmarkagent.xpc.plist
[failed] com.apple.security.cloudkeychainproxy.plist [Details]
[failed] com.apple.spindump_agent.plist [Details]
[failed] com.apple.syncdefaultsd.plist [Details]
[failed] com.apple.telephonyutilities.callservicesd.plist [Details]
[failed] com.apple.xpc.loginitemregisterd.plist
Problem System Launch Daemons: ℹ️
[failed] com.apple.awdd.plist [Details]
[failed] com.apple.ctkd.plist [Details]
[failed] com.apple.nehelper.plist [Details]
[failed] com.apple.softwareupdated.plist [Details]
[failed] com.apple.tccd.system.plist [Details]
[failed] com.apple.wdhelper.plist [Details]
[failed] com.apple.xpc.smd.plist [Details]
[failed] org.cups.cupsd.plist [Details]
Launch Agents: ℹ️
[running] com.micromat.TechToolProAgent.plist [Support]
[running] com.robohippo.HippoConnectAgent.plist [Support]
[not loaded] com.rosettastone.rosettastonedaemon.plist [Support]
[loaded] org.gpgtools.gpgmail.enable-bundles.plist [Support]
[loaded] org.gpgtools.gpgmail.patch-uuid-user.plist [Support]
[loaded] org.gpgtools.gpgmail.updater.plist [Support]
[running] org.gpgtools.Libmacgpg.xpc.plist [Support]
[loaded] org.gpgtools.macgpg2.fix.plist [Support]
[running] org.gpgtools.macgpg2.shutdown-gpg-agent.plist [Support]
[loaded] org.gpgtools.macgpg2.updater.plist [Support]
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist [Support]
[loaded] com.barebones.authd.plist [Support]
[not loaded] com.barebones.textwrangler.plist [Support]
[loaded] com.bombich.ccc.plist [Support]
[running] com.bombich.ccchelper.plist [Support]
[loaded] com.charlessoft.pacifist.helper.plist [Support]
[loaded] com.ea.origin.ESHelper.plist [Support]
[running] com.freemacsoft.appcleanerd.plist [Support]
[loaded] com.klieme.TimeMachineScheduler.plist [Support]
[running] com.micromat.TechToolProDaemon.plist [Support]
[not loaded] com.robohippo.HippoConnectDaemon.plist [Support]
[loaded] org.gpgtools.gpgmail.patch-uuid.plist [Support]
[not loaded] org.virtualbox.startup.plist [Support]
User Launch Agents: ℹ️
[loaded] com.google.keystone.agent.plist [Support]
[running] com.spotify.webhelper.plist [Support]
[loaded] com.valvesoftware.steamclean.plist [Support]
[not loaded] net.brockerhoff.QuayMenu.plist [Support]
[not loaded] org.virtualbox.vboxwebsrv.plist [Support]
[loaded] uk.co.markallan.clamxav.freshclam.plist [Support]
[running] ws.agile.1PasswordAgent.plist [Support]
User Login Items: ℹ️
Bartender Application (/Applications/Bartender.app)
Flux Application (/Users/[redacted]/Applications/Flux.app)
iTunesHelper Application (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
Dropbox Application (/Applications/Dropbox.app)
Dashboard KickStart Application (/Library/PreferencePanes/Dashboard KickStart.prefPane/Contents/Resources/Dashboard KickStart.app)
PastebotSync ApplicationHidden (/Users/[redacted]/Library/PreferencePanes/PastebotSync.prefPane/Contents/Resou rces/PastebotSync.app)
Quicksilver Application (/Applications/Laucher from Herbie/Accessories/Login Items/Quicksilver.app)
finderpop-daemon Application (/Users/[redacted]/Library/PreferencePanes/FinderPop.prefPane/Contents/Resource s/finderpop-daemon.app)
EvernoteHelper Application (/Applications/Evernote.app/Contents/Library/LoginItems/EvernoteHelper.app)
Synergy Application (/Applications/Synergy ƒ/Synergy Preferences.app/Contents/PreferencePanes/Synergy.prefPane/Contents/Helpers/Syne rgy.app)
ClamXav Sentry Application (/Applications/ClamXav.app/Contents/Resources/ClamXavSentry.app)
Messages Application (/Applications/Messages.app)
AppCleaner Helper Application (/Applications/Launcher/Utilities/System/AppCleaner.app/Contents/Library/LoginI tems/AppCleaner Helper.app)
Steam Application (/Applications/Steam.app)
EtreCheck Application (/Applications/EtreCheck.app)
Mail Application (/Applications/Mail.app)
MacUpdate Desktop ApplicationHidden (/Applications/MacUpdate Desktop.app)
Internet Plug-ins: ℹ️
Flip4Mac WMV Plugin: Version: 2.4.4.2 [Support]
FlashPlayer-10.6: Version: 16.0.0.235 - SDK 10.6 [Support]
QuickTime Plugin: Version: 7.7.3
Flash Player: Version: 16.0.0.235 - SDK 10.6 [Support]
NPRoblox: Version: 1, 2, 8, 25 - SDK 10.9 [Support]
Default Browser: Version: 600 - SDK 10.10
Silverlight: Version: 5.1.30514.0 - SDK 10.6 [Support]
JavaAppletPlugin: Version: 15.0.0 - SDK 10.10 Check version
User internet Plug-ins: ℹ️
Picasa: Version: 1.0 - SDK 10.4 [Support]
Safari Extensions: ℹ️
Buffer
Add To Amazon Wish List
Ghostery
Evernote Web Clipper
jollywallet cash back
Reading
1Password
Save to Pocket
Social Fixer
3rd Party Preference Panes: ℹ️
Dashboard KickStart [Support]
Diablotin [Support]
FinderPop [Support]
Flash Player [Support]
Flip4Mac WMV [Support]
GPGPreferences [Support]
Growl [Support]
MacFUSE [Support]
MagicPrefs [Support]
NuFile [Support]
Pastebot Sync [Support]
PathSnagger [Support]
Perian [Support]
SharePoints [Support]
TechTool Protection [Support]
TimeMachineScheduler [Support]
Time Machine: ℹ️
Skip System Files: NO
Mobile backups: ON
Auto backup: NO - Auto backup turned off
Volumes being backed up:
SylerNet Adjunct: Disk size: 269.14 GB Disk used: 205.43 GB
Jane's Brain: Disk size: 627.01 GB Disk used: 538.19 GB
Destinations:
data [Network]
Total size: 2.00 TB
Total number of backups: 27
Oldest backup: 2014-11-28 08:04:00 +0000
Last backup: 2014-12-08 18:53:02 +0000
Size of backup disk: Too small
Backup size 2.00 TB < (Disk used 743.62 GB X 3)
Top Processes by CPU: ℹ️
      9% iTunes
      3% WindowServer
      1% coreaudiod
      1% Steam Helper
      0% Boom
Top Processes by Memory: ℹ️
129 MB com.apple.WebKit.WebContent
120 MB mds_stores
112 MB Finder
103 MB Folder Actions Dispatcher
77 MB Spotlight
Virtual Memory Information: ℹ️
72 MB Free RAM
1.02 GB Active RAM
942 MB Inactive RAM
648 MB Wired RAM
9.41 GB Page-ins
1.30 GB Page-outs
Diagnostics Information: ℹ️
Dec 10, 2014, 10:12:12 PM Self test - passed
Dec 10, 2014, 07:13:15 PM MacUpdate Desktop_2014-12-10-191315_Jane.crash
Dec 10, 2014, 06:31:37 PM Civilization IV Beyond the Sword_2014-12-10-183137_Jane.crash
Dec 9, 2014, 07:30:06 PM MacUpdate Desktop_2014-12-09-193006_Jane.cpu_resource.diag [Details]
Dec 9, 2014, 03:50:06 PM Finder_2014-12-09-155006_Jane.hang
Dec 9, 2014, 03:19:44 PM MacUpdate Desktop_2014-12-09-151944_Jane.cpu_resource.diag [Details]
Dec 9, 2014, 02:36:11 PM EvernoteHelper_2014-12-09-143611_Jane.crash
Dec 8, 2014, 02:11:35 PM SCNAlembic_2014-12-08-141135_Jane-2.crash
Dec 7, 2014, 11:21:52 PM Numbers_2014-12-07-232152_Jane.hang
Dec 8, 2014, 10:40:55 PM WindowServer_2014-12-08-224055_Jane-2.crash
Dec 10, 2014, 01:02:37 AM garcon_2014-12-10-010237_Jane.crash
Dec 10, 2014, 06:31:11 PM Civilization IV Beyond the Sword_2014-12-10-183111_Jane.crash
Dec 10, 2014, 01:26:58 AM Install Adobe Flash Player_2014-12-10-012658_Jane.crash
Dec 9, 2014, 07:31:50 PM garcon_2014-12-09-193150_Jane.crash

Preferences Error Could not load Desktop

MacBook Air (11-inch, Mid 2012) OS X Yosemite when trying to access my screensaver and desktop, I keep getting the following
Preferences Error Could not load Desktop & Screen Saver preference pane.
Any suggestions?
Thanks

Close all windows and quit all applications.
Hold the option key down and click the "Go" menu in the Finder menubar.
Select "Library" from the dropdown, then "Preferences" folder.
Look for these three files.
com.apple.screensaver.plist
com.apple.desktop.plist
com.apple.systempreferences.plist
Right click each one of those and select " Move To Trash" from the contextual menu.
Restart the computer.

DW Extract error: could not load Extract panel

Similar Messages

Maybe you are looking for