Dynamic global hostname is not saving

I was trying to setup my new airport time capsure to use dyn. When I tried to add the dynamic host name and tsig information on a mac using the airport utility it would not save. When I entered the information from the airport utility on an iphone it saved the information and I am able to verify that it is there from the mac.
So my question: is this an issue with my information (domain name, tsig etc) that I am trying to enter or is it an issue with the airport utility on the mac
My airport is running version 7.7.1
The airport utility on the mac is 6.3 (630.34)
and the airport utility on the iphone is the current one from the appstore
-Philip Hutson

after buying a domain name, spending moeny at DynDns and then 6 hours trying to configure it i found this,
From DynDns:
Note: as of version 6.1 of the Airport Utility and 7.6.1 router firmware, the Apple Airport Extreme and Time Capsule routers no longer offer the ability to configure wide-area bonjour. This has effectively caused these Apple routers to no longer support sending updates to Dyn Standard DNS. If you are attempting to set up earlier versions of the Airport Utility and firmware, you can use these instructions, but this is an experimental feature, we cannot provide technical support for this setup. If you need assistance, check out the Dyn Community.

Similar Messages

What is "Dynamic Global Hostname" in Internet Options? Is it DDNS?

If you have an Airport Extreme or a Time Capsule with updated firmware you will find "Use dynamic global hostname" in: Airport Utility > Internet tab > Internet options. There is literally no Apple provided documenation on this setting within the device's user manual, instructions, or online support. The only documenation you will find are on various blogs and forums such as this one. So, here is a screenshot of the setting and my questions below:
1. I'm assuming that this is where I can setup Dynamic DNS if I have an account with a DDNS provider such as DynDNS or NoIP. Is this correct?
2. If this is where I can setup DDNS, then what should the hostname be? Should it be the hostname I have setup with a DDNS provider, like this: MySite.DDNS.com? Or, should the hostname include my device's actual hostname, like this: TimeCapsule.MySite.DDNS.com?
3. For the "User" and "Password" fields, should this be the account that I have with the DDNS provider? If yes, then what is the format of the username.. is it just my DDNS account username: "MyAccount"? Or, should it be: [email protected]?
I'm trying to setup DDNS because I'd like to have remote SSH access to several of my Linux systems on my network and I don't want to configure a DDNS client on the Linux systems if the Time Capsule can do it. This is because my Time Capsule will always be online but my Linux systems are not always online.
Thanks for any help with this setting! It is definitely strange because "Dynamic Global Hostname" is not an "industry standard" term. Typically, it is called "Dynamic DNS" instead. So that's why I'm trying to figure out what this setting really is and if it can help me with my DDNS and remote access needs.

Did some digging, found this article http://dyn.com/support/bonjour-and-dns-discovery/. Step 4 has something interesting to say:
> The User and Password fields are NOT the Dyn account username and password!Instead, they refer to a special type of authentication for dynamic DNS updates called Transaction Signature, or TSIG.Retrieve your TSIG information from your TSIG account settings page, and populate the information in the Userand Password fields as shown in the diagram, and then click OK.
Hope that helps anybody else. I assumed that the user/pass were the ones used to login to the account but nope, they're not.

Wide-Area Bonjour / Dynamic Global Hostname

Hello everyone
I have a very specific problem, My AEBS is not sending UPDATE requests to my own DNS server when my DSL IP address changes over time.
I have my own DNS server and run a dynamic zone with TSIG aututhentication.
If I configure the "Dynamic global hostname" on my Macs behind my AEBS acting as a NAT gateway, they will register themselves withe the correctly natted address.
In fact, this is amazing and works very well:
sftp-ssh.tcp.dyn.secret.domain domain name pointer MacPro.sftp-ssh.tcp.dyn.secret.domain.
smb.tcp.dyn.secret.domain domain name pointer MacPro.smb.tcp.dyn.secret.domain.
ssh.tcp.dyn.secret.domain domain name pointer MacPro.ssh.tcp.dyn.secret.domain.
macpro.dyn.secret.domain has address xx.yy.169.96
But my AEBS itelf has an older address:
airport.tcp.dyn.secret.domain domain name pointer Airport.airport.tcp.dyn.secret.domain.
smb.tcp.dyn.secret.domain domain name pointer Airport.smb.tcp.dyn.secret.domain.
airport.dyn.secret.domain has address xx.yy.177.175
I can force the update by restarting my AEBS, but this is not a good workaround.
Has anyone else experience running a wide-area bonjour DNS server?
Thanks

Hi Patrick,
I suggest you bring this up on the bonjour-dev[1] mailing list. You're much more likely to reach people with the right knowledge there.
Andrew
[1] http://lists.apple.com/mailman/listinfo/bonjour-dev

Airport Extreme -Dynamic Global Hostname-

Is somebody using the "Use Dynamic Global Hostname" ( under Internet/Internet Options ) with "No-Ip.com" ?
I learned that DynDNS doesn't supprt this so I am wondering if No-Ip does.
Thanks.

I was wondering if DynDNS supported this because I have used No-Ip and it apparently does not. Or at least it is an undocumented feature if it does. No-Ip does have an updater application that you run on your computer which will update the ip address on their site. This is fine for most uses.
What I have gleaned from searching is that DynDNS did support using that setting until Apple removed wide-area Bonjour from the Airport Utility software interface. However the latest version still includes the settings. So I was thinking that perhaps it would still work for the purpose of updating your dns. One thing I have noticed is that some posts here suggest the user and password are of the DynDNS account itself, whereas on the DynDNS site I have seen a support document which suggests that you need to provide a Transaction Signature. Something which has to be created from your account on their site.

Aiport Dynamic Global Hostname

Hi !!
Is there anyone who is aware of free of charghe dynamic dns services who id known to work -compatible- with this?
http://goo.gl/retTn
(dynamic global hostname form from apple airport utility 5.6)
Thanks

Rmemeber way back when Apple used to make thing easier?.....
As is standard now...   Apple has taken something that should be easy, and turned into something that CAN NOT BE DONE AT ALL.    See the note below from DynDns, Airport changed the firware so this doesn't work.   Usually when this happens it is not a mistake, it is "Removal of Functionality"   ( see: SNMP which is also gone )
Apple won't support normal DynamicDns like every other router manufacturere in the world.   And their alternative is "Dynamic Global Hostname"... which no longer works.
Now what is my option Apple??    None?.... yeah that's what i thought.
---From DynDns
Note: as of version 6.1 of the Airport Utility and 7.6.1 router firmware, the Apple Airport Extreme and Time Capsule routers no longer offer the ability to configure wide-area bonjour. This has effectively caused these Apple routers to no longer support sending updates to Dyn Standard DNS. If you are attempting to set up earlier versions of the Airport Utility and firmware, you can use these instructions, but this is an experimental feature, we cannot provide technical support for this setup. If you need assistance, check out the Dyn Community.

Do some ISPs pick up the dynamic global hostname (global Bonjour)?

Wouldn't it be nice if ISPs would pick up the dynamic global hostname (aka global Bonjour) and feed it via 'mybonjourname.provider.com' to their DNS servers?
As long as one knows one's ISP and leaves the computer (or Time Capsule or AEBS) always connected to the same ISP, one would not need any dynamic DNS service. Particular since it is a bit difficult to get a dynamic DNS client run on a Time Capsule not connected to a computer...

Background: I recently purchased a MacBook Pro (MBP) and a Time Capsule (TC) installed at home. I use the TC for back-ups, as well as a home server to store music, photographs, personal and work archives of information. I want to be able to access the content that I have inside my TC from anywhere. I have three Apple laptops, all of them with a family dot.mac account, however, they may not be on or at home at all times, therefore my challenge is to be able to access the TC content from anywhere when only the TC is ON and no other laptops may be on. Unfortunately only Macs can use and update the dot.mac with the Back to my Mac (BTMM) feature, and the TC does not have a way to use BTMM by itself. The Airport Extreme (AE) and the TC the same (or very similar) router software modules built-in. Most routers have a built-in way to enter a dynamic IP or DNS updater (global bonjour). The dot.mac is one such global DNS updaters, but it does not use an open architecture. Another global DNS updater is DynDNS. I opened a DynDNS account, and in the TC I turned ON file sharing and in Airport > Time Capsule > Edit I entered the DynDNS information. If the global bonjour updater functioned well, this last action should instruct the TC to keep my DynDNS account informed of its IP address at all time. This would allow me when on travel to go to the web page of my DynDNS account, visualize the current IP address of my TC, click on it or cut and paste in the"Go to Server", and this would automatically mount the TC Hard Disk on my Desktop. However this is not working as planned. The software of the Time Capsule accepts the global bonjour account of DynDNS but fails to update it with its current IP address, as a result, the DynDNS knows the first IP address when you first program it, but as soon as the IP address of the TC changes it stops working (and this could be a matter of minutes, hours, days or weeks). I have used Linkys and DLink routers in the past, and they have worked flawlessly with DynDNS and other IP Updaters. However, I have never been able to use the TC IP updater features reliably.
+The issues:+ (a) Airport Extreme (AE) and Time Capsule (TC) router software modules have a global bonjour feature that is not working well with DynDNS and do not update it when its IP address changes. (b) There is no way to program a dot.mac account on the AE or TC and use dot.mac BTMM feature to access the disks mounted on the AE or TC without invoking another computer with dot.mac; By other words, if we want to access remotely (outside our LAN, via the internet) a disk connected to our AE or TC, we must have a Mac in the same LAN with either a dot.mac account or a DynDNS account, otherwise we are unable to find its IP address to access the TC directly.
As far as I know, until Apple updates the AE or TC software to either use dot.mac or reliably update an IP updater like DynDNS, we will not be able to reliable access a TC remotely without another Mac in the same LAN doing the IP updating. If anyone can shed some additional light on this issue I will appreciate if.

Domain hosting provider that supports Dynamic Global Hostname?

Is there any domain hosting provider that supports dynamic DNS of the variety that supports "dynamic global hostname" used by Mac OS X, accessed in the Sharing control panel, and used by AirPort Express and Time Machine? I am referring to the Dynamic DNS method specified by IETF RFC 2136.

Any VPS provider will give you full control over your BIND installation.

Set up dynamic global hostname on Lion Server

In order to connect to the different MacBook I would like to use the dynamic global hostname
Can anyone share his expiriance on setting up a dynamic global hostname service on Lion Server?

More details are needed.
Do you see a background? Icons? Tool bar with Apple menu? Can you restart? Can you bring up Mission Control or go to a different space?

How Airports base station update Dynamic Global Hostname?

Hello!
For several days, I try to run my own DNS server with bind9.
My Airport Express has a dynamic IP and I would like to be able to use dynamic DNS.
When you configure the DNS server on my bind9 (linux machine), Airport update the entries, but when I want to protect the DNS using keys (dnssec or rndc) my Airport can not update the entry (update denied). The DNS server is configured correctly, because I can update it via nsupdate from another linux machine.
My Airport firmware is 7.6.4
Please help in solving this problem.

Hello!
For several days, I try to run my own DNS server with bind9.
My Airport Express has a dynamic IP and I would like to be able to use dynamic DNS.
When you configure the DNS server on my bind9 (linux machine), Airport update the entries, but when I want to protect the DNS using keys (dnssec or rndc) my Airport can not update the entry (update denied). The DNS server is configured correctly, because I can update it via nsupdate from another linux machine.
My Airport firmware is 7.6.4
Please help in solving this problem.

Will dynamic global hostnames ever work properly again?

AEBS firmware 7.4.1 broke dynamic dns updating. Any attempt to set it up now simply results in TSIG errors.
7.4.2 didn't fix it.
Has anyone gotten signed dynamic DNS updates working on recent firmware revs of the AEBS?
Will this feature ever work properly again???

Hi berkeleywalker,
I understand your discontent. I can assure you that all software updates developed by the manufacturer are intended to make your phone work better. Since you have done a Factory Reset and your phone continues to experience performance issues after you installed your applications, I recommend running your phone in Safe Mode for a while to ensure that no third party application conflicts exist. If your phone works properly in Safe Mode then a third party application conflict is causing your phone to malfunction and the conflicting application must be identified and removed from your phone.
There is no easy way to identify a conflicting 3rd party application, the only way is to remove all applications and add one by one and test until the conflicting app is identified and then removed for good.
AntonioC_VZWSupport
Follow us on Twitter at www.twitter.com/vzwsupport

Preferences, Global Defaults not saving

Hi
I've watched a demonstration (found here: http://bit.ly/5i3lnC) of how to set the defaults (start CP4, Shift F8, set the object preferences, OK, repeat from Shift F8 etc).
I've then opened a blank project and exported my preferences (as the blog described).
I've closed that project and opened up a new project, from a template. Then I've imported the preference file.
However when I go into Shift F8 to ensure it matches the object preferences that I set up and exported, it does not.
The preferences I set up for the Mouse object has saved, but the preferences for the Highlight Box and Text box and others have not saved. I had them set up with the Effect: No Transition. Some I had set to Display for: Rest of slide.
I'd also set the Preview defaults to 3 slides and this has not saved either, or it hasn't imported.
Am I doing something wrong, or have I misunderstood what the Global Defaults were meant to do?
Thanks
Anita

Hello,
You need to change the global preferences to change the default style of your captions. In order to do that you need to make sure that without open any project click on Edit Preferences>Recording>Defaults create a new style and apply it .
Click on OK to close the object style manager dialog box.
Then start your recording again and check the default captions.
Regrads,
Rajeev.

How to get local and global hostnames working?

I have a new AirPort TimeCapsule, and I can't get the local hostname (appleair.local) to work from browsers on the local network. Is that how it's supposed to work?
The TC is in bridge mode because it's behind a Netgear WAP+router -- maybe that is a problem?
I had to set up a global hostname to get Bonjour working in order to share an old printer (attached to the TC) across the network, but my understanding is that I can't actually use a global hostname from a browser without setting up a dynamic DNS service. Is that right? I'd like to be able to share files and the printer on the TC without using Bonjour if possible.
Apart from the USB printer attached to the TC, there's an external flash drive attached to the Netgear router used for backups and as a media server.
I originally configured the TC with my iPhone and an iPad mini, but now I'm working on the advanced settings with a Windows laptop using the Apple AirPort Utility for Windows and connecting to the TC wirelessly. There's a MacBook and iMac that will be added to the network, but they're not available yet so that's why I'm using the PC.

The 5.6.1 utility for windows is really not up to handling the new AC version TC.. Apple specify that you must use a version 6 airport utility but none has been released for windows.
You will have to use bonjour for windows. but you should not need to use full domain name..
By default the TC is local domain. But if your computer is getting an IP from the Netgear it might be in a different domain. How much this matters I am not sure. But I would simply try to get everything on the one domain. I think you are confused anyway.
I have a new AirPort TimeCapsule, and I can't get the local hostname (appleair.local) to work from browsers on the local network. Is that how it's supposed to work?
The TC has no html access.. never has had.. probably never will have.. for reasons known only the higher powers of Apple inc.. they do not use standard HTML access.. the only way to access the TC is via airport utility. So putting the ip or the name in a browser is useless.. it will not and cannot respond.
Sharing printers from the TC to windows is always going to be a mystery bag.. I would suggest you simply delete all your previous attempts and try again.. setting up printers via bonjour in windows.. shudder..
http://support.apple.com/kb/HT2835

Visio 2010 - Shape Data Fields Are Not Saving

I am having a problem with a number of shape data fields which are not saving data that has been entered into it, whether by entering it through the "shape data" or "define shape data" dialog boxes, or by editing the "shape
sheet".
All data fields appear to save normally while file is open, it remains as entered. However, when file is closed and later reopened select data fields do not retaining data correctly. Some retain nothing (null), or revert back to a "default"
value, see below for a couple examples:
Rack Units: Want to enter data as 1U, 2U, etc. ... in some cases it will save it as entered while in other cases it reverts to "1 RU", "2U", etc.
Room: Enter the data as I want it stored, most of the time it appears to come back empty, there are some shapes which will retain as entered.
Comments: Fails to retain any data
I have looked at a number of reasons to explain why, whether the problems occur with stencils is supplied by Microsoft, a vendor, or were custom created. Looked into whether it might have to do with a particular vendor's stencils/drawings
but I have a number of Cisco drawings where some save those fields as entered while others do not. I believe it could be a setting within the stencil preventing it from saving the data as entered, enabled in some cases and not in others.
I have checked "Protection" under the "Developer" tab, but nothing appears to be set to prevent editing/storing data entered.
Is there some setting(s) or field(s) somewhere that I can look at to allow this data to be saved as entered?
Is there a GLOBAL setting that can be set once within a file?
Thank you in advance for your time to assist me in fixing these problems. Have a great day!
MJ_NWE
MJ

>Can I build logic so that they can't fill in a field unless the previous field has been filled in?
It's theoretically possible to do this (e.g. each field has an action
of removing read-only on the next). It's considered extremely bad form
design, because people don't always fill in fields in the order
specified. If you watch people with a form they fill in their name,
address, other easy stuff; then they go back for the harder stuff.
They may want to save a form because one piece of information needs
research.
What you might like to consider is a large splash "FORM INCOMPLETE" in
Red or whatever, which vanishes when all the fields are completed.
Aandi Inston

Window sizing not saved?

I resize a sheet in Number v3 and save it bit the careful sizing I set is not saved and a small default window size opens when I re-open the file. How can I save my window sizing as per Number 09?
Thanks
Gary

Hi,
I think window auto-tuning is enabled.
You can disable it by running the following commend.
netsh interface tcp set global autotuninglevel=disabled
Hope this helps.

BPC 5.1 ownership % not saving.

HI Team,
I am trying to fill ownership% and method for consolidation in Dynamic hierarchy under each legal entity.
By adding sibling but system is not saving the ownership data including childs to group.
Please help us to resolve this.
Regards
Naveen.KV

I gave up on the dynamic hierarchy. It is buggy to say the least.
I would suggest that you just create an input template against the Ownership application and just load your numbers there,

Dynamic global hostname is not saving

Similar Messages

Maybe you are looking for