Dynamic IP Address not working on MBP

Hello:
I am experiencing a problem with my MacBook Pro not being able to assign an IPv4 IP Address when "Using DHCP" is selected for either a wifi or ethernet connection. In order to be able to connect either device, I have to manually add an address (i.e., 192.168.0.36) & use "Using DHCP with manual address" instead.
It is interesting to note that all other devices on my home network work perfectly and all use DHCP and have addresses assigned to them. These devices include iPad's, iPhone's, AppleTV, etc... The only device that does not work is my MacBook Pro. Thinking it was a network issue, I reset my DSL router as well as my Airport Extreme to default settings and re-configured my network. This proved to be of no use.
Has anyone else expierienced this issue and know a possible solution?
Thanks in Advance.

If you have the public on the WAN of the router, you do not need it on the server. The server wants to be a static on the same range as the LAN of the router. If you have the router LAN set as 192.168.1.1 (which is the default of most out there)
you want the IP of the server to be something like 192.168.1.10, with the same subnet mask of the LAN of the router (Usually 255.255.255.0) and the Default Gateway of the server to be the LAN IP of the router (in this example: 192.168.1.1). For DNS,
you probably want to set the LAN IP of the router, as the router should send any requests to the public DNS set by the ISP.
This should get the server back online.

Similar Messages

Why Dynamic Parameter is not working, when i create report using stored procedure ?

Post Author: Shashi Kant
CA Forum: General
Hi all
Why Dynamic Parameter is not working, when i create report XI using stored procedure ?
Only i shaw those parameters which i used in my stored procedure, the parameter which i create dynamic using stored procedure
is not shown to me when i referesh the report for viewing the results.
I have used the same procedure which i mention below but can not seen the last screen which is shown in this .
============================================================================================
1. Select View > Field Explorer2. Right-click on Parameter Fields and select New from the right-click menu.3. Enter u201CCustomer Nameu201D as the name for your parameter4. Under u201CList of Valuesu201D select u201CDynamicu201D5. Under the Value column, click where is says u201Cclick here to add itemu201D and select Customer Name from the drop-down list. The dialog shown now look like the one shown below in Figure 1. Click OK to return to your report design.
Dynamic Parameter Setup6. Next, select Report > Select Expert, select the Customer Name field and click OK.7. Using the drop-down list beside select u201CIs Equal Tou201D and using the drop-down list, select your parameter field (it should be the first field). 8. Click OK to return to your report design and see the parameter dialog.The parameter dialog will appear and show you a dynamic list of values that is updated each time your run your report. It couldnu2019t be easier! In our next tutorial, we will be looking at how to use this feature to create cascading parameter fields, where the values are filtered by the preceding selection.
Dynamic Parameters in Action
My question is that whether dynamic parameter is working with storedprocedure or not.
When i added one table and try to fetch records using dyanmic prameters. after that i am not be able to find the dynamic parameter option when i referesh my report.
One more thing when i try the static parameter for my report, the option i see when i referesh the screen.
Please reply soon , it's urgent
Regards
shashi kant

Hi Kishore,
I have tested the issue step by step by following you description, while the first issue works well in my local environment. Based on my research, this can be caused by the lookup expression or it indeed return Male value based on the logic. If you use the
expression below, it will indeed only return the Male record. So please try to double-check the record in the two datasets and the expression in your environment:
=lookup(first(Fields!ProgramID.Value,"DataSet1"),Fields!ProgramID.Value,Fields!Gender.Value,"DataSet2")
As to the second issue, please try to use the following expression:
=Count(Lookup(fields!ProgramID.value,fields!ProgramID.value,fields!Gender.value,"DataSet2"))
Besides, if this issue still exist, in order to trouble shoot this issue more efficiently, could you please post both the .rdl file with all the size properties to us by the following E-mail address? It is benefit for us to do further analysis.
E-mail: [email protected]
Thanks,
Katherine Xiong
Katherine Xiong
TechNet Community Support

Premiere Pro to Adobe Audition Dynamic link does not work. Cannot edit audio in Audition.

Trying to edit Audio from Premiere Pro within Audition thru the Dynamic link but it does not fire up Audition to edit. Seems like a common problem/bug. But no one has posted a solution. Please Help
-Windows 7
-Premiere Pro CC 2014
-Adobe Audition CC 2014

You dont understand it was all working fine in the previous Adobe versions. matter of fact you can go on youtube and see a couple of videos that shows the work flow between Premiere Pro and audition by way of Dynamic link. If you edit a video clip in Premier Pro and want to add some music or simply edit the audio that is contained in the video there was a time within Premiere Pro you can just right click "Edit in Adobe Audition" and Audition would open with the audio clip in place. Much in the same way Premiere Pro works with After Effects thru the Dynamic Link. The Dynamic Link is the bridge between applications to work with each other. For some reason Premiere Pro and Audition Dynamic Link is not working properly.

HT5312 Rescue email address not work and I forget my security question answers

Rescue email address not work and I forget my security question answers

If you don't have access to your rescue email account (you won't be able to change it until you can answer 2 of your questions), or you aren't receiving the email to it, then you will need to contact iTunes Support or Apple to get the questions reset.
e.g. you can try contacting iTunes Support : http://www.apple.com/support/itunes/contact/ - click on Contact iTunes Store Support on the right-hand side of the page, then Account Management , and then 'Forgotten Apple ID security questions'
or try ringing Apple in your country and ask to talk to the Accounts Security Team : http://support.apple.com/kb/HE57
When they've been reset you can then use the steps half-way down the page that you posted from to update your rescue email address for potential future use, or you could change to 2-step verification : http://support.apple.com/kb/HT5570

VPN Client and Dynamic isakmp keys not working

Hi,
I'm trying to enable DMVPN endpoints from dynamic IP addresses, e.g. adding in:
crypto isakmp key XXXXXXX address 0.0.0.0 0.0.0.0 no-xauth
The problem is when I add this line, it breaks our remote VPN Client. Removing the line makes everything work fine again, except I can't add a DMVPN endpoint that has a dynamic IP.
Presently all DMVPN spokes have static IP addresses configured and individual keys for each (I'm trying to simply/cut down our config and use a single key for all of them plus enable staff from home on dynamic IP's).
I can't tell if this is an IOS bug, or if I need to configure something differently.
Our VPN client is configured as a dynamic map, e.g.:
crypto isakmp client configuration group vpnclient
key RAH RAH RAH
etc.
crypto isakmp profile vpnclient
   match identity group vpnclient
   client authentication list vpnuser
   isakmp authorization list vpngroup
   client configuration address respond
crypto ipsec transform-set VPNCLIENT esp-aes 256 esp-sha-hmac
crypto dynamic-map vpnclient 10
set transform-set VPNCLIENT
set pfs group2
set isakmp-profile vpnclient
crypto map vpn 65535 ipsec-isakmp dynamic vpnclient
And then attached to my WAN interface as crypto map.

Hi Scott,
What IOS Version are you using ? I don't see any reason that this command would break Remote VPN Connectivity.
Maybe you can try
crypto isakmp key XXXXXXX address 0.0.0.0 0.0.0.0 (remove the no-xauth, as it's not needed).
Otherwise, you may share output of debug crypto isakmp to see exactly what is failing when the remote users are connecting.
Regards,
Bastien

Manually set IP addresses not working as needed

We have setup our DCHP server in that we manually not dynamically give IP addresses to workstations according to there mac addresses. But most of the time the the workstations go and get the IP addresses dynamically, and in this case most of the time we get IP conflict. Does it mean the giving IP addresses manually does not work properly in the DHCP configuration. For reasons, we need to use Manually assigned IP addresses not dynamically. And how can I trace why the manually configured workstation go and get IP addresses dynamically ?

It should work properly. Please post your configuration.

Erec - leaving action deleted internal candidate email address not working

Good morning
We have the following situation:
1. A person was made a leaver in HR with future leaving date.
2. Decision was made that the person could actually stay so the leaving action was deleted in HR.
3. In erec in SU01 person still showing as role RCF_INT however the email address (produced from IT105 subtype 0010 in HR) was blank and his Alias field populated with his employee number ie: as if he was a leaver still.
4. I have manually updated the email address in erec for his internal email address - this did not let him apply for an internal job. I then deleted it in IT105 in HR and then recreated it in IT105 - this has gone across to Erec however he still cannot apply and the Alias field is still being populated.
So erec is behaving as if he is part internal and part external! How can I stop the Alias field being populated for him and how can I then get the email address to work?
many thanks
Dawn

Hi Nicole
Thank you. The order of events was as follows:
a. On 25.01.11 a leaving action was done to start 01.04.11
b. A decision made in March that the individual could stay however the leaving action was not deleted until 08.04.11
c. This meant that he became a leaver in erec and due to subsequently deleting the leaving action he has reverted to INT_CAND (which is what we want).
I have managed to get the email address to work by deleting the IT105 subtype 0010 in HR, I then recreated it in HR and it has PFAL'd over to erecruitment so the user is now able to apply for jobs.
However the Alias field is still populated and the user has an additional employee number in erecuitment. Are you able to advise how the alias field can be depopulated?
Many thanks
Dawn

Cascading Dynamic Parameters Do Not Work In Crystal Viewer 2008?

I have generated a report with Crystal Reports 2008 that uses a dynamic cascading parameter. I work in waste management and the report I create in Crystal is used as a "template" with the tonnages collected from all of our customers. Our less technically minded employees can then open this report with Crystal Reports Viewer 2008, use the drop down menus to select only the customer they need a report for and then export this to PDF for delivery.
The report as designed works perfectly in Crystal Reports, but the parameter does not work in Crystal Viewer.
Some of our customers have more than one physical location that we service. The cascading dynamic parameter in my report allows you to select the customer name, and then it only shows the locations linked to that customer, so the end user can select only the relevant location(s) for the report. The cascading parameter is dynamic and allows multiple selections, and is linked to a Saved Data formula. The report is saved with the data.
When the report is opened in Viewer, one of two things happens. If the report is saved in Crystal Reports and a specific customer/location is selected, then ONLY those selected customer/locations are available in the Viewer. If ALL the customers/locations are selected in Crystal Reports and saved, then in the Viewer they are all available, but selecting one customer does NOT narrow down the locations (i.e. it does not "cascade") and instead ALL of the locations are available even if they do not apply to the customer.
If I use a single dynamic parameter and select ALL of the customers (for example), then when this is opened in Crystal Viewer all of the customers are available from the parameters drop down and the report works fine. As soon as this is tried with a cascading parameter however, Crystal Viewer falls down.
Does anyone know of a workaround to this or if there is something I am doing wrong?

I am using the free Crystal Report 2008 Viewer along with designing reports with Crytal Reports ver 12.3. With a test file from SAP called "Interactive Parameters", the parameter feature works to refresh the report. The parameters that are supplied in the sample report work with Viewer. They show up under the parameter list in the parameter side panel in Viewer and are available to make record selections. When I add a parameter to the sample report in Crystal 2008 and then view the report in Viewer, my parameters are unavalable for record selection while the original parameters remain available. Futher, my parameters are displayed under a section called "Current Data Set" in the Parameter side panel, while the selectable parameters are displayed under the "Parameter" section in the parameter side panel. There must be a setting that is treating the parameters I create differently form the parameters created in the original sample report. Any help would be appreciated.

Vpn-framed-ip-address not working with anyconnect

Hi Folks, please help me to verify if this case is a bug or a "not valid scenario".
Scenario:
ASA 5520, OS 9.1, SSL VPN with Anyconnect v3.x, static ip address for the client, and RSA token authentication (all the users/pin/passwords are in the RSA server, not in the ASA, but i need to create some users in the ASA in order to apply the vpn-framed-ip-address attribute for specific users).
In fact the anyconnect ssl vpn with RSA auth works fine, the ssl connection works, the user is authenticated, the anyconnect works, traffic passing, BUT.. the anyconnect its getting an ip address from the ip local pool INSTEAD of the static ip defined with the vpn-framed-ip-address command.
I'm trying to assign a static ip address for a user (defined locally on the ASA) that performs auth via RSA (aaa-server), by using the vpn-framed-ip-address command as an attribute for this local user. But it seems the command is not working.
Already I´ve tried to resolve (with no success) by entering the
no vpn-addr-assign aaa
no vpn-addr-assign dhcp
vpn-addr-assign local
Also i´ve tried by removing the pool from tunnel-group in order to force all the connection session to use the static ip address, but in this case, the anyconnect sends a message "No Address Available for SVC Connection". Meaning the ASA simply is ignoring the vpn-framed-ip-address command.
Its supposed the ASA implement the policies in this order, DAP > User policy > UserGrp policy > ConnProfile > DefGrpPolicy, and according to this, the vpn-framed-ip-address command should take effect first since its specified as User policy, overriding everything else. But its not working.
At this point i think the issue is... since the user is locally defined but its password its being authenticated via RSA (not local), the user attributes (static ip) are being ignored by the ASA because its not expecting to receive an ip address from the aaa server (RSA), so jumps to the next policies falling to the pool. Anyway the user policies attributes SHOULD work according to cisco.
Please your advise, or tell if its a bug? or a not valid scenario for this command to work with the ASA.
This is the current config:
ip local pool PoolSSL 192.168.229.10-192.168.229.19 mask 255.255.255.0
aaa-server RSA protocol sdi
aaa-server RSA (inside) host 192.168.12.1
retry-interval 5
no vpn-addr-assign aaa
no vpn-addr-assign dhcp
group-policy GroupPolicyABC internal
group-policy GroupPolicyABC attributes
wins-server none
dns-server value 192.168.61.1 192.168.61.2
vpn-tunnel-protocol ssl-client
group-lock value TunnelGroupABC
split-tunnel-policy tunnelspecified
split-tunnel-network-list value ServersDB
default-domain value my.domain.com
split-tunnel-all-dns disable
webvpn
anyconnect ask none default anyconnect
username USER1 password xHhacRZ56Uadqoq encrypted
username USER1 attributes
vpn-framed-ip-address 192.168.229.7 255.255.255.0
group-lock value TunnelGroupABC
tunnel-group TunnelGroupABC type remote-access
tunnel-group TunnelGroupABC general-attributes
address-pool PoolSSL
authentication-server-group RSA
default-group-policy GroupPolicyABC
tunnel-group TunnelGroupABC webvpn-attributes
group-alias AccessToDB enable
I´ll wait for your answers, regards!

https://tools.cisco.com/bugsearch/bug/CSCtf71671/
you need AAA assignment, or at least you needed to have it a couple of years back.

Why is my symbol loaded dynamically from library not working?

Hope someone could help,
The code in "Example1" work fine if the video symbol is located on the stage. But what I'm trying to do is load the video symbol from the library dynamically and that doesn't work as illustrated in "Example2".
My question is why does Example1 work and Example2 not work?
Example1:
var youtube = $("<iframe/>");
sym.$("video").append(youtube);
youtube.attr('type', 'text/html');
youtube.attr('width', '560');
youtube.attr('height', '315');
youtube.attr('src', 'https://www.youtube.com/embed/A3PDXmYoF5U');
youtube.attr('frameborder','0');
youtube.attr('allowfullscreen', '0');
Example2:
sym.myVideo;
sym.myVideo = sym.createChildSymbol("video", "Stage");
var youtube = $("<iframe/>");
sym.$("myVideo").append(youtube);
youtube.attr('type', 'text/html');
youtube.attr('width', '560');
youtube.attr('height', '315');
youtube.attr('src', 'https://www.youtube.com/embed/A3PDXmYoF5U');
youtube.attr('frameborder','0');
youtube.attr('allowfullscreen', '0');
Thanks in advanced,
-Angel

Have you tried a reset:
Hold the Sleep and Home button down for about 10 second until you see the Apple logo.

Crystal Reports dynamic parameter does not work in InfoView

Hello,
We have developed Crystal Reports in CR2008 on top of SAP infoset and we have one of our selection parameter as dynamic parameter. It works fine in the CR Dev tool but when i upload the report in the InfoView, report does not show any value in the "Available Values"
Any input will be much appreciated.
Thanks.

I did found the solution for this, i had to go into Business View Manger (BO Client Tools) and Schedule the LOV (List of Values). This is odd setting! but it works....

Populating Text Field using Dynamic Actions is not working

I've a Select List (P14_ACCOUNT) and Text Field (P14_BILLING_ADDRESS_1) on a form. On selecting a value on the Select List, I've to populate the Text Fields by fetching its values from the database by using the Select List value as the primary key. To do this, I created a Dynamic Actions (Advanced) on the Select List, with event onchange and Set Value as SQL. However this is not working.
Below are the sqls of Select List and Dynamic Action respectively:
select ACCOUNT_NO || ' - ' || COMPANY_NAME display_value, ACCOUNT_ID return_value
from ACCOUNT
order by 1
select a.address1 from account a where a.account_id = :P14_ACCOUNTNow when I substitute the Dynamic Action sql with any of the below sqls, the value shows up:
select address1 from account where account_id = 41
select address1 from account where rownum=1
select user from dualI thought of seeing the value of :P14_ACCOUNT in session or debug, but session does not show any value and on clicking debug it throws a popup message "Debugging is not enabled for this application."
I've been trying since few hours but with no luck. How can I debug further?
Thanks for the help.
--Hozy

Hozy,
Take alook at your application on apex.oracle.com
The session state for items, when SQL is used, is set using the Page Items to Submit parameter as has been set in your application.
Regards,

Adobe Dynamic Link will not work - Premiere Pro CS4 to After Effects CS4

Hello,
I am edited a video with a deadline, I'm importing a sequence from Premiere Pro CS4 to After Effects and making edits in After Effects. I'm able to import the Premiere Pro sequence into After Effects using Dynamic Link, but I go back to Premiere Pro and nothing has changed. Then I have to export the 21 minute long video in After Effects and that takes about 12 hours, that I can't afford. I don't know what I'm doing wrong, before I imported the timeline into AE, while I was in Premiere Pro I right clicked it and selected -Edit original. It took me to the .mov that I imported- since it's a redo. I learned how to use Dynamic Link from this tutorial-
http://tv.adobe.com/watch/learn-cs4-production-premium/using-dynamic-link/
At first when Dynamic link didn't work I thought it was because I was cutting the imported Sequence from Premiere Pro in After Effects becasue I was motion tracking. When you import a Premier Pro sequence can you cut it into individual layers in After Effects?

I'm importing a sequence from Premiere Pro CS4 to After Effects
That doesn't create the type of Link you want here. In this case, changes made to PP would show up in AE. You want the reverse. (And you can only go one way, not both.)
http://help.adobe.com/en_US/PremierePro/4.0/WS725e431141e7ba651172e081238226cdf5-8000.html

Richard Huggins/Art ? email address not working Reply here

I received this email.
The return address does not work.
On 13 Mar 2006, at 22:51, art wrote:
On 3/13/06 1:13 PM, Richard Huggins wrote:
My daughter has the world's cutest toddlers and a PC. I, grand-dad, live 300
miles away and have a MacBook Pro with the built-in camera. So you now
understand my subject topic!
I'm new to the video chat stuff, so I'd appreciate help with what she could
use and I could use and us both see/hear each other. (She mentioned that She
has Skype, but Skype's Mac version does not yet support video.) I'm thinking
that I can't use iChat for this, but if I'm wrong let me know.
Thanks,
Richard
Sent using the Microsoft Entourage 2004 for Mac Test Drive.
Richard,
This might be possible depending on the configurations of the computers and the speeds of the communications links that you both have. iChat can be a bit tricky to set up for audio/video sessions, especially if there are one or more firewalls involved.
There's an excellent narrative on the specific topic of iChatPC at:
http://www.ralphjohnsuk.dsl.pipex.com/page12.html
You might check out the iChat forums in the Apple discussion groups at:
http://discussions.apple.com/category.jspa?categoryID=139
There is a wealth of knowledge and assistance about iChat related issues on these forums. There tends to be more active discussions regarding iChat related issues then here in the Usenet groups.
If you are unsuccessful with iChat, try Sight Speed (www.sightspeed.com). There are free clients for both Mac and PC. Unlike iChat, it is client-server based (iChat is peer-to-peer) so there are less obstacles to success.
It doesn't have as good video/audio quality as iChat and the echo suppression isn't as advanced, but it is much easier to set up. Also, unlike iChat, the conferencing capabilities (more than two users) are not included with the free versions.
HTH...
Regards,
Art
My reply was
Hi,
iChat will Video chat to the AIM 5.9 Application or Trillian Pro ($25) run on a XP PC.
Both ends need some settings up. The AIM application more, with an extra "Tuning" stage.
The AIM application needs the Tuning and Enabling through the XP firewall (links to Tuning and an Explanation of the Firewall stuff on the Page 12 link)
The Trillian needs just enabling though the XP firewall.
Both ends also need to make sure the applications involved can also get through the routers and modems involved.
This page has links to Real People testers and some Autoresponding test accounts. Both ends should try contacting the autoresponding accounts and then with a selection of the Real People, to see where they are up to. Then Try PC to PC and Mac to Mac before trying Mac to PC (Or the other way round).
This list has some cross platform stuff
There is also YakforFree iVisit and others out there.
I hope this helps whoever sent the email.
4:58 PM Thursday; March 16, 2006

Hi ernestw31,
First make sure that you're using the email address that you used to set up your subscription. If you are and still can't sign in, please contact Adobe Customer Support; an agent can help you resolve your account issue.
Click the Chat link at https://www.acrobat.com/misc/en/contact-support.html. Chat is available from 5am – 7pm PST.
Please let us know if you need further assistance.
Best,
Sara

Answer-address not work

Dear Admin,
I have tried few day already to match inbound call base on Calling number.
Call made from calling number range 8000-9 and try to terminate the call by prefix 332168 thru TDM link but it was not work.
Below is my scenario and configuration detail. Please advice if anything wrong.
Partner A ( Over SIP protocol ) ------> ( Inbound SIP ) AS5400 ( TDM )----->PSTN
dial-peer voice 332855 pots
description Outbound to TDM-A
max-conn 1
answer-address 800[0-9]
destination-pattern 332168.
progress_ind alert enable 8
port 6/7:D
dial-peer voice 3328551 voip
description Inbound Sip from KZ
voice-class codec 1
session protocol sipv2
answer-address 800[0-9]
Best Regards,
Daneth

Call Apple Care and ask for the Account Security Team. They can assist you with your issue.

Dynamic IP Address not working on MBP

Similar Messages

Maybe you are looking for