Dynamic partitioned Hard Driver cannot be accessed when connected by USB 3.0 Enclosure

Hi Guys,
Here is my issue.
There is a 2TB SATA Hard Drive, formatted to NTFS with 64KB chunk size blocks. The partition type is dynamic.
I removed the drive from a system and brought it to another location.
This time is is connected via USB 3.0 enclosure, which I know it works and it was tried with different hard drives with no issue.
The Windows is 8.1. It sees the disk but cannot Reactivate it. It shows the reactivate option, but when you select it you see a message:
Virtual Disk Manager
This operation is not allowed on the invalid disk pack.
OK
I understand that USB dynamic disks might not be supported, but the scenario above is valid.
My question is how to bring the partition online using USB enclosure?
Is there a registry workaround or other which involves no data loss?
It is very pity not to allow using USB 3.0 when you have a dynamic partition. I do not see any physical limitations to do so.
Thanks for your help!

Hi,
As I known, whether the USB enclosure can identify the dynamic hard drive, it depends on the USB driver and USB specification.
But to make your computer recognize this hard drive well, we have the workaround to change it to basic disk type:
http://windowsforum.com/threads/dynamic-disk-invalid.3906/
This response contains a reference to a third party World Wide Web site. Microsoft is providing this information as a convenience to you. Microsoft does not control these sites and has not tested any software or information found on
these sites; therefore, Microsoft cannot make any representations regarding the quality, safety, or suitability of any software or information found there. There are inherent dangers in the use of any software found on the Internet, and Microsoft cautions
you to make sure that you completely understand the risk before retrieving any software from the Internet.
Hope these could be helpful.
Kate Li
TechNet Community Support

Similar Messages

Hard drive gets error -50 when connected internally, but not in USB enclosure.

I have a SATA hard drive that works perfectly when connected through an external USB enclosure but whenever it's plugged into the internal SATA connector on my MacBook Pro I receive the error message "The operation can’t be completed because an unexpected error occurred (error code -50)." any time I attempt to move or copy a file to it.
This doesn't happen with any other hard drive I connect internally, so I don't believe it's an issue with the internal cable.
I have made sure all permissions are set to allow reading and writing to the drive as well as selecting the "Ignore ownership on this volume" option in the Get Info panel.

If I were you, I would just replace the drive. Since other drives work, you're probably right in assuming that it's not a SATA cable issue, but rather an issue with that specific drive.
Clinton
MacBook Pro (15-inch Late 2011), OS Mavericks 10.9.4, 16GB Crucial RAM, Crucial M500 960GB SSD, 27” Apple Thunderbolt Display

Why do files on an external hard drive appear as alias when connected to Time Capsual's USB?

Situation:
I have an old MacBook Pro (2008) and all of its USB and CD ports have stopped working (only the Ethernet port works). As a workaround, I purchased a 2TB Time Capsule, connected it via Ethernet to the MacBook Pro, and set up a wireless network that my MacBook Air (2010), ipads/pods, can connect.
Attempting to Accomplish:
1. Provide a back-up for my Pro since I cannot connect via USB
2. Move photos off my Air (to free up space) and combine with my Pro's library
3. Share files, music, and photos between all my devices (stored on both my Pro, Time Capsule, and external Maxtor hard drive)
Problem:
My last Pro back-up was to a Maxtor external hard drive. Also, all my Air photos are on the same external hard drive. I connected this hardrive to the Time Capsule. When I accessed the Maxtor from the Pro (through my new airport network) I can see the file hirearchy, but when I drill down to my Air's iPhoto library (back-up, latest, user, x, photos) the files appear with the alias symbol on them. The message I get when clicking is something about them being no longer connected. HOWEVER, when I attach this Maxtor via direct USB to my Air, both the Air backups and the Pro back ups appear as real files (no alias icon) and can be opened and transferred. When my Pro's ports worked I frequently shared files this way with no alias icons.
Disclaimer: I'm mac-savy enough that the genius bar is adding no real value/help, but not nearly as technical as most people on this board. And I'm very un-technical with networking. So if you can point me in the right direction, please "speak" simply =)

Ok, confirmed. It is NTFS and according to the permissions I can only read it. The frustrating thing is that it says:
    - Capacity: 74.53 GB
    - Available: 50.35 GB
    - Used: 24.18 GB on disk
and yet at the bottom of the file list it shows "0 items"
Now the dilemma. The harddrive on my Windows laptop is very small (30GB) so I cannot copy all of my pictures to it. I could hook the old harddrive and the new harddrive up to it at the same time and move them from old to new, however...
The new harddrive is supposed to only be for the Mac so my intention was to format it that way. Because I am not sure if/how I am going to need it to resolve this issue, the box hasn't even been opened...so the first question is long term would it be better to have the new harddrive MAC or FAT32 formatted?
I have been assuming that Mac formatting was the preferred route so I am still brainstorming on ways to get the files straight from the old harddrive to the Mac. Could it just be a matter of the files being hidden on the old harddrive? How do I unhide them?

Re-partitioning hard drive, XP to Win7 upgrade

Realizing that my existing XP Boot camp (3.0.1) partition was not going to be large enough for Win7, I deleted my existing partition along with my XP installation.
Two issues
1- I now cannot partition my newly un-partitioned hard drive in Boot Camp. I got some message about the memory already being used, and the need for a journaled format.
According to Disk Utility, my HD format is Mac os extended (journaled). My RAID type is Mirrored RAID type.
Any ideas how to get my disk to partition? I did zero out all the free space on the drive before trying to partition.
2- To get to Win7, do I now have to reinstall XP, upgrade Boot Camp to 3.1, install Win7?
Another problem I seem to have is that i bought an Upgrade version of Win7. Is that going to work for me?
Thanks in advance for any help. NEIL

Hi Neil,
1- I removed my previous boot camp partition. My Mac HD is mac osx extended (journaled). raid type is mirrored raid set, but raid size is 0 kb. What should my settings be, and where do i change them?
So you have a RAID set with Disk Utility but are not using it ?
What exactly is the 'layout' of your harddisks ?
If you don't use that once set RAID, it might be best to clean house right now and get rid of it.
Disk Utility can do this, but you have to backup your OSX first, since undoing a RAID deletes the content of the HDs/partitions in it.
2- in your post, you reference the following link within a thread http://codesociety.com/2008/10/23/boot-camp-cannot-partition-disk-files-could-no t-be-moved-error/ but this page is jibberish. Any other advice on what to do when boot camp cannot partition?
Sorry, seems that that page is gone for bad.
Like said, the BootCamp Assistant needs to find a free contigeous amount of diskspace of the size you specify in the BCA when partitioning.
That error you get implies that the BCA can not find it.
Have a look at my other posts in the thread I linked to, on how-to use an external harddisk and something like SuperDuper or Carbon Copy Cloner to clone your OSX back and forth to get the needed free diskspace for the BCA.
Stefan

Is it possible to have two encrypted time machines on one partitioned hard drive?

I am trying to use encrypted time machines for two macbooks (15" and 11") with only one USB hard drive. The problem is that after creating one encrypted time machine for my 15" in a separate partition, the hard drive does not work when plugging it into my 11".
What happens is that I am prompted to enter in my encryption password for the 15" time machine on my 11". I enter in the correct password but it does not work (i.e., password fail). The interesting part is that when I plug the hard drive into my 15", I am asked the same thing, but the password entry works.
This is my current setup for my 1tb usb hard drive:
1) 400gb for data
2) 400gb newly encrypted time machine for my 15"
3) 200gb unencrypted time machine (with old 11" time machine backups) for my 11"
The hard drive is formated/partitioned in RAID format.
All I want is to be able to have two encrypted time machines for each macbook on one single hard drive. Previously I was able to maintain two separate time machines (unencrypted) on this hard drive. I decided to try and encrypt both but seems like I am getting something wrong.

I am prompted to enter in my encryption password for the 15" time machine on my 11".
If I understand correctly, you want to mount the other partition. Are you prompted to do that? Does the password include any characters other than plain letters and digits? Are you using the same keyboard layout on both machines?

Can you share an external hard drive over a network when your Apple Airport Extreme is in bridge mode?

Hello, is it possible to share an external hard drive over a network when I have my Airport Extreme in bridge mode? I can't use my AE as my main router at the moment but still want to be able to use the hard drive on the network, and the router I am using isn't capable of adding an external hard drive. I use Windows 7 and the other router is a Netgear. I have searched the communities and have not come across an answer to this question. I have tried several configurations within windows to try and see the hard drive but none have worked. I can see the hard drive when I run Airport utlities, but it cannot be seen on the network. Thanks to anyone who can help!

I think there is some confusion in this thread..
If you are sharing on a local LAN port forwarding is not required.
is it possible to share an external hard drive over a network when I have my Airport Extreme in bridge mode?
Answer is yes.. no port forwarding, mapping whatever term is used.. is needed. Port mapping is required when you cross over a NAT router.. as long as all the devices are inside a single LAN.. then no port mapping.
I assign to my Airport Extreme, do I do so with the settings of:
Service: SMB
Type: TCP
Server IP: xx.x.x.x
Port Start: 445
Port End: 445
This would not work even from WAN.. SMB is blocked by all responsible ISP.. there is simply too many unprotected windows machines out there. If they allowed SMB .. the world would be flooded with hijacked bots. And stolen data like bank accounts. SMB is not a secure protocol.
But this is not necessary on a LAN.
The problem can be Mavericks which does a terrible job presenting network drives.. The usual recommendations are to use AFP or force the connection to CIFS (ie SMB1 not 2).
If you use airport,, then use AFP.
In finder.. Go, Connect to server.
AFP://AEname or AEIPaddress. (replace with the network name of the AE or its actual IP address).
When asked for password.. type public if you did not change it or use whatever password you put.
Store the password in the keychain.

Need Urgent help, I have made partition hard drive in my mac book and using OS mac

Need Urgent help, I have made partition hard drive in my mac book and using OS mac & Window8 seperately... for couple of days it works great for both window & OS mac But nowadays, my pc gets restart automatically while using window & even I cant access to my Mac OS........... I got some error in window (error80070003) ...>>>>> Now how can I format whole drive & recover my Mac book OS.without boot disk.

I can't find that model. If you open System Profiler in the Utilities folder look for the Model Identifier over in the right hand display. What do you find for the model ID? If your computer supports Internet Recovery here's what to do:
Install Mavericks, Lion/Mountain Lion Using Internet Recovery
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Internet Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND-OPTION- R keys until a globe appears on the screen. Wait patiently - 15-20 minutes - until the Recovery main menu appears.
Partition and Format the hard drive:
Select Disk Utility from the main menu and click on the Continue button.
After DU loads select your newly installed hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed. Quit DU and return to the main menu.
Reinstall Lion/Mountain Lion. Mavericks: Select Reinstall Lion/Mountain Lion, Mavericks and click on the Install button. Be sure to select the correct drive to use if you have more than one.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
This should restore the version of OS X originally pre-installed on the computer. If Mavericks is not installed, then you can reinstall it by re-downloading the Mavericks installer.
You will need to use Boot Camp Assistant in order to create a new Windows partition, then reinstall Windows.

Can i partition hard drive and run 10.6 on one and 10.4 on other

I have software that only runs under 10.4 on my older Imac. I would like to partition hard drive and run 10.6 on one and 10.4 on the other. Is this possible? Can I get instructions?

Yes.
Just set up the partitions. If you already have a 10.4.x and 10.6.x drives then "clone" them up as bootable backups with a backup utility like Carbon Copy Cloner or Super Duper.
When booting you can hold down the option key to get a list of bootable volumes (select with arrow keys and hit return). You can use Startup Disk for either of them to define the default system to boot from if you don't use the option key technique.
If you don't already have these systems then of course you will have to install them in their respective partitions.
You have to realize of course that these are two distinct systems each with their own version of your login directory.

Can Lion disk utility dynamically partition a drive?

Can Lion disk utility dynamically partition a drive? I see many posts that Leopard Disk utility can but nothing about Lion.

Yes. I'll post a link to instructions. Be sure to create a full reliable backup before you begin (don't just do the backup, test the backup to be sure it's good), and the only application that should be running until the process is complete is Disk Utility.
http://osxdaily.com/2009/11/20/resize-partitions-in-mac-os-x-with-disk-utility/
Some people have problems resizing partitions because of the hidden Recovery HD partition. It sometimes gets in the way because Disk Utility can move it "up" but cannot move it "down".

I am having trouble installing Lion on a partitioned hard drive. Help?

Aloha:
I am having trouble installing Lion on a partitioned hard drive
I have three internal HD's The first I am running the system on 10.6.8 (which is up to date) , the second I do most of my work on and the third I have partitioned into two and I am trying to install Lion on one of the patitions.
But Lion has decided it will only go on the first HD.
Above is the one I want to put it on, but it's not available and I can't change the partition scheme. None of the things the directions state are usable??
What might I be doing wrong?
Thanks
Dan Page

Thanks again for a rapid responce.
I finally got lion on one partition and my daily "SilverKeeper" backup on the other.
Since the only thing I had on the two partition Hard drive was the back up and since the backup would get put on tonight any way I changed the drive to no partitions. This gave me the ability to choose the GUID option, which I did and then I installed two partitions and successfuly istalled Lion on one of them. I even tied Lion into the iCloud successfuly.
But I am not out of the woods yet! I brought My brand new iPad to lunch and was informed that my iPad was synced to my Lion at home and I was on the cloud. That blew my mind, I was impressed.
I then read the Daily news with out problem, however, when I shut down my iPad, that was all she wrote. I can not get the iPad back on. The best I could do was see the revolving gear start and then freeze. It's on charge now and I can not even get rid of the frozen gear.
Not sure this all has anything to do with the recent installation on my main computer, but it's mighty suspicious.
Need some help!!
Thanks
Dan

Cant partition hard drive :S

Ok - trying to load arch onto my main hard drive. It is 160gb and have made a partition by right clicking on 'my computer' ->manage and shrinking my drive to 123gb and having a new ntfs volume or 25gb.
Thing is, when I boot from the arch cd and go to partition hard drive, the only one I can select is the entire 160gb. When I select that I get an error message too so cant even format my whole disk (even though I dont want to).
Any ideas on what I should do?

Ok, tried again, I go into the manual partition and the only drive is size 1600000, I get to choose a partition /dev/sda1 I think and then it give me:
Bad primary partition 1: Partition ends in the final partial cylinder :S

I want to know if I can backup my Ipad to an external harddrive. I have a pc with xp pro media edition and a partitioned hard drive with very little space on C and lots on D. I am trying to update my Ipad to 5.1.1 and it says it needs 12 gb to backup.

I have a Sony Vaio desktop PC with a partitioned hard drive, running Windows XP Pro. There is 13 gb on C drive with the OS, and 140 gb left on D drive. I am trying to update my Original Ipad from 4.3.4 to 5.1.1 and because C drive is full ( I have moved everything that can be moved to D drive) mostly from Microsoft updates over the years, I am unable to do the backup Itunes is telling me I have to do to update or lose all media on this iPad. 12.67 gb is required to do the backup and I have a whopping 965.2 MB. I can not get the cloud to use as backup as it requires 5.0 or better. Does anyone know if I can back up to D drive, and if so how? Also, I have a 1 terrabyte WD mini external hard drive I just got as a gift...could I do the backup to it and, again, if so, how? Please explain from start to finish, as my brain is now fried from, first from finally getting Itunes updated to 10.6 ,and now trying to do this update. Thanks to anyone for their help!!

iOS device backups are stored in your iTunes library.
Move your iTunes library to an external drive.

I had to install a new hard drive on my computer, when I downloaded itunes back onto my computer, none of my songs were there. how do i get them back??

I had to install a new hard drive on my computer, when I downloaded Itunes, all my music was gone. How do i get my music back? I do not have an Icloud.

Syncing to a "New" Computer or replacing a "crashed" Hard Drive: Apple Support Communities
You can redownload iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store

My Mac Book hard drive is nearly full. How do I move iTunes music, etc folders to a different location on an external hard drive and still access as if on my Mac?

My Mac Book hard drive is nearly full. How do I move iTunes music, etc folders to a different location on an external hard drive and still access as if on my Mac?

http://support.apple.com/kb/HT1449

I have all my music cd's on a hard drive as wav files when I try to add them to I tunes the files get there but no album info I end up with a bunch of track 1's by unknown artists. Is there a way to transfer each album over so it shows up like a normal CD

I have all my music cd's on a hard drive as wav files when I try to add them to I tunes the files get there but no album info I end up with a bunch of track 1's by unknown artists. Is there a way to transfer each album over so it shows up like a normal CD

Try posting in a more appropriate forum, as this has noting to do with itunes U - the place where University/college/museums post education material.

Dynamic partitioned Hard Driver cannot be accessed when connected by USB 3.0 Enclosure

Similar Messages

Maybe you are looking for