Dynamin VPN/GRE can't ping other side of tunnel
I am new at this VPN stuff and tryiong to setup a GRE Dynamic IP VPN between my offfice and home. Here is what I ahve done thus far:
OFFICE
interface Tunnel0
ip address 172.30.1.1 255.255.255.252
no ip redirects
ip mtu 1400
ip nhrp map multicast dynamic
ip nhrp network-id 1
ip tcp adjust-mss 1360
tunnel source FastEthernet0/0
tunnel mode gre multipoint
tunnel key 1
interface FastEthernet0/0
ip address 40.197.68.9 255.255.255.248
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
HOME
interface Tunnel0
ip address 172.30.1.2 255.255.255.252
ip mtu 1400
ip nhrp map multicast 40.197.68.9
ip nhrp map 172.30.1.1 40.197.68.9
ip nhrp network-id 1
ip nhrp nhs 172.30.1.1
ip tcp adjust-mss 1360
tunnel source GigabitEthernet0/0
tunnel destination 40.197.68.9
tunnel key 1
interface GigabitEthernet0/0
description Router
ip address 192.168.30.1 255.255.255.252
duplex auto
speed auto
When I ping 172.30.1.1 from the HOME router, I get 0/5 success. Not good! I have not setup any IPSec yet.
Results for HOME router
show ip nhrp nhs detail
Legend: E=Expecting replies, R=Responding, W=Waiting
Tunnel0:
172.30.1.1 E priority = 0 cluster = 0 req-sent 53 req-failed 0 repl-recv 0
sh int t0
Tunnel0 is up, line protocol is up
Hardware is Tunnel
Internet address is 172.30.1.2/30
MTU 17912 bytes, BW 100 Kbit/sec, DLY 50000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation TUNNEL, loopback not set
Keepalive not set
Tunnel source 192.168.30.1 (GigabitEthernet0/0), destination 40.197.68.9
Tunnel Subblocks:
src-track:
Tunnel0 source tracking subblock associated with GigabitEthernet0/0
Set of tunnels with source GigabitEthernet0/0, 1 member (includes iterators), on interface <OK>
Tunnel protocol/transport GRE/IP
Key 0x1, sequencing disabled
Checksumming of packets disabled
Tunnel TTL 255, Fast tunneling enabled
Tunnel transport MTU 1472 bytes
Tunnel transmit bandwidth 8000 (kbps)
Tunnel receive bandwidth 8000 (kbps)
Last input 00:40:28, output 00:00:25, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/0 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
106 packets output, 12612 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
sh ip route
Gateway of last resort is 192.168.30.2 to network 0.0.0.0
S* 0.0.0.0/0 [1/0] via 192.168.30.2
10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks
C 10.110.0.0/24 is directly connected, GigabitEthernet0/1.110
L 10.110.0.1/32 is directly connected, GigabitEthernet0/1.110
C 10.115.0.0/24 is directly connected, GigabitEthernet0/1.115
L 10.115.0.1/32 is directly connected, GigabitEthernet0/1.115
172.16.0.0/30 is subnetted, 1 subnets
S 172.16.2.0 [1/0] via 192.168.30.6
172.30.0.0/16 is variably subnetted, 2 subnets, 2 masks
C 172.30.1.0/30 is directly connected, Tunnel0
L 172.30.1.2/32 is directly connected, Tunnel0
S 192.168.2.0/24 is directly connected, GigabitEthernet0/0
S 192.168.10.0/24 is directly connected, GigabitEthernet0/0
192.168.30.0/24 is variably subnetted, 4 subnets, 2 masks
C 192.168.30.0/30 is directly connected, GigabitEthernet0/0
L 192.168.30.1/32 is directly connected, GigabitEthernet0/0
C 192.168.30.4/30 is directly connected, GigabitEthernet0/1.30
L 192.168.30.5/32 is directly connected, GigabitEthernet0/1.30
S 192.168.50.0/24 [1/0] via 192.168.30.6
192.168.69.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.69.0/24 is directly connected, GigabitEthernet0/1.69
L 192.168.69.3/32 is directly connected, GigabitEthernet0/1.69
S 192.168.100.0/24 [1/0] via 192.168.30.6
S 192.168.125.0/24 [1/0] via 192.168.30.6
S 192.168.200.0/24 [1/0] via 192.168.30.6
sh dmvpn
Interface: Tunnel0, IPv4 NHRP Details
Type:Spoke, NHRP Peers:1,
# Ent Peer NBMA Addr Peer Tunnel Add State UpDn Tm Attrb
1 50.197.68.90 172.30.1.1 NHRP 02:30:17 S
Results for OFFICE router
show ip nhrp nhs detail
sh dmvpn
sh int t0
Tunnel0 is up, line protocol is up
Hardware is Tunnel
Internet address is 172.30.1.1/30
MTU 17912 bytes, BW 100 Kbit/sec, DLY 50000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation TUNNEL, loopback not set
Keepalive not set
Tunnel source 40.197.68.9 (FastEthernet0/0)
Tunnel Subblocks:
src-track:
Tunnel0 source tracking subblock associated with FastEthernet0/0
Set of tunnels with source FastEthernet0/0, 1 member (includes iterators), on interface <OK>
Tunnel protocol/transport multi-GRE/IP
Key 0x1, sequencing disabled
Checksumming of packets disabled
Tunnel TTL 255, Fast tunneling enabled
Tunnel transport MTU 1472 bytes
Tunnel transmit bandwidth 8000 (kbps)
Tunnel receive bandwidth 8000 (kbps)
Last input 00:43:56, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/0 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
show ip route
S* 0.0.0.0/0 [1/0] via 40.197.68.94
40.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C 40.197.68.8/29 is directly connected, FastEthernet0/0
L 40.197.68.9/32 is directly connected, FastEthernet0/0
172.30.0.0/16 is variably subnetted, 2 subnets, 2 masks
C 172.30.1.0/30 is directly connected, Tunnel0
L 172.30.1.1/32 is directly connected, Tunnel0
S 192.168.2.0/24 [1/0] via 192.168.10.5
192.168.10.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.10.0/24 is directly connected, FastEthernet0/1
L 192.168.10.1/32 is directly connected, FastEthernet0/1
S 192.168.69.0/24 is directly connected, FastEthernet0/0
Why can't Io ping from the HOME router to the OFFICE router?
I fugured this problem out. I needed to setup PKI/IKE and once that was done on both routers, my tunned now passes some data.
Similar Messages
-
ASA 5505 VPN clients can't ping router or other clients on network
I have a ASA5505 and it has a vpn set up. The VPN user connects using the Cisco VPN client. They can connect fine (the get an ip address from the ASA), but they can't ping the asa or any clients on the network. Here is the running config:
Result of the command: "show running-config"
: Saved
ASA Version 7.2(4)
hostname ASA
domain-name default.domain.invalid
enable password kdnFT44SJ1UFX5Us encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 10.0.0.4 Server
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
clock timezone MST -7
clock summer-time MDT recurring
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list vpn_splitTunnelAcl standard permit any
access-list inside_nat0_outbound extended permit ip any 10.0.0.192 255.255.255.192
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPNpool 10.0.0.220-10.0.0.240 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface smtp Server smtp netmask 255.255.255.255
static (inside,outside) tcp interface pop3 Server pop3 netmask 255.255.255.255
static (inside,outside) tcp interface www Server www netmask 255.255.255.255
static (inside,outside) tcp interface https Server https netmask 255.255.255.255
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
http server enable 480
http 10.0.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map outside_dyn_map 20 set pfs group1
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
group-policy vpn internal
group-policy vpn attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpn_splitTunnelAcl
username admin password wwYXKJulWcFrrhXN encrypted privilege 15
username VPNuser password fRPIQoKPyxym36g7 encrypted privilege 15
username VPNuser attributes
vpn-group-policy vpn
tunnel-group vpn type ipsec-ra
tunnel-group vpn general-attributes
address-pool VPNpool
default-group-policy vpn
tunnel-group vpn ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:df7d1e4f34ee0e155cebe86465f367f5
: end
Any ideas what I need to add to get the vpn client to be able to ping the router and clients?
Thanks.I tried that and it didn't work. As for upgrading the ASA version, I'd like to but this is an old router and I don't have a support contract with Cisco anymore, so I can't access the latest firmware.
here is the runnign config again:
Result of the command: "show startup-config"
: Saved
: Written by enable_15 at 01:48:37.789 MDT Wed Jun 20 2012
ASA Version 7.2(4)
hostname ASA
domain-name default.domain.invalid
enable password kdnFT44SJ1UFX5Us encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 10.0.0.4 Server
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
clock timezone MST -7
clock summer-time MDT recurring
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list vpn_splitTunnelAcl standard permit any
access-list inside_nat0_outbound extended permit ip any 10.0.0.192 255.255.255.192
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPNpool 10.0.0.220-10.0.0.240 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
asdm location Server 255.255.255.255 inside
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface smtp Server smtp netmask 255.255.255.255
static (inside,outside) tcp interface pop3 Server pop3 netmask 255.255.255.255
static (inside,outside) tcp interface www Server www netmask 255.255.255.255
static (inside,outside) tcp interface https Server https netmask 255.255.255.255
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
http server enable 480
http 10.0.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map outside_dyn_map 20 set pfs group1
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
group-policy vpn internal
group-policy vpn attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpn_splitTunnelAcl
username admin password wwYXKJulWcFrrhXN encrypted privilege 15
username VPNuser password fRPIQoKPyxym36g7 encrypted privilege 15
username VPNuser attributes
vpn-group-policy vpn
tunnel-group vpn type ipsec-ra
tunnel-group vpn general-attributes
address-pool VPNpool
default-group-policy vpn
tunnel-group vpn ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect icmp
service-policy global_policy global
prompt hostname context
Cryptochecksum:78864f4099f215f4ebdd710051bdb493 -
One router on ASA 5505 Site to Site VPN can't ping other router
I have two Cisco ASA routers and I have a site to site vpn set up between the two. The VPN link works but Site A can't ping anything on Site B. Site B can ping Site A. Site B can ping other pcs on it's own network. Site A has been in place for a while and has other site to site VPNs that work fine, so I think the problem is with Site B. Here is the config for Site B:
Result of the command: "show running-config"
: Saved
ASA Version 8.4(4)1
hostname SaskASA
enable password POgOWyKyb0jgJ1Hm encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.16.1 255.255.254.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
ftp mode passive
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network NETWORK_OBJ_192.168.16.0_23
subnet 192.168.16.0 255.255.254.0
object network NETWORK_OBJ_192.168.2.0_23
subnet 192.168.2.0 255.255.254.0
access-list outside_cryptomap extended permit ip 192.168.16.0 255.255.254.0 192.168.2.0 255.255.254.0
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source static NETWORK_OBJ_192.168.16.0_23 NETWORK_OBJ_192.168.16.0_23 destination static NETWORK_OBJ_192.168.2.0_23 NETWORK_OBJ_192.168.2.0_23 no-proxy-arp route-lookup
object network obj_any
nat (inside,outside) dynamic interface
nat (inside,outside) after-auto source dynamic any interface
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable 444
http 192.168.16.0 255.255.254.0 inside
http 0.0.0.0 0.0.0.0 inside
http 0.0.0.0 0.0.0.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 207.228.xx.xx
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map interface outside
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcp-client client-id interface outside
dhcpd auto_config outside
dhcpd address 192.168.16.100-192.168.16.200 inside
dhcpd auto_config outside interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy GroupPolicy_207.228.xx.xxinternal
group-policy GroupPolicy_207.228.xx.xx attributes
vpn-tunnel-protocol ikev1 ikev2
username User password shbn5zbLkuHP/mJX encrypted privilege 15
tunnel-group 207.228.xx.xxtype ipsec-l2l
tunnel-group 207.228.xx.xxgeneral-attributes
default-group-policy GroupPolicy_207.228.xx.xx
tunnel-group 207.228.xx.xxipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:f06bd1d6d063318339d98417b171175e
: end
Any ideas? Thanks.I looked over the config for Site A, but couldn't find anything unusual. Perhaps I'm overlooking something. Here is the config for site A:
Result of the command: "show running-config"
: Saved
ASA Version 8.2(1)
hostname SiteA
domain-name domain
enable password POgOWyKyb0jgJ1Hm encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.254.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
dns domain-lookup inside
dns server-group DefaultDNS
name-server 192.168.2.6
domain-name domain
object-group network DM_INLINE_NETWORK_1
network-object 192.168.14.0 255.255.254.0
network-object 192.168.4.0 255.255.254.0
network-object 192.168.6.0 255.255.254.0
network-object 192.168.8.0 255.255.254.0
object-group network DM_INLINE_NETWORK_2
network-object 192.168.12.0 255.255.254.0
network-object 192.168.14.0 255.255.254.0
network-object 192.168.4.0 255.255.254.0
network-object 192.168.6.0 255.255.254.0
network-object 192.168.8.0 255.255.254.0
access-list outside_1_cryptomap extended permit ip 192.168.2.0 255.255.254.0 object-group DM_INLINE_NETWORK_1
access-list inside_nat0_outbound extended permit ip 192.168.2.0 255.255.254.0 object-group DM_INLINE_NETWORK_2
access-list inside_nat0_outbound extended permit ip any 192.168.15.192 255.255.255.192
access-list inside_nat0_outbound extended permit ip 192.168.2.0 255.255.254.0 192.168.16.0 255.255.254.0
access-list VPNGeo_splitTunnelAcl standard permit any
access-list outside_2_cryptomap extended permit ip 192.168.2.0 255.255.254.0 192.168.6.0 255.255.254.0
access-list outside_3_cryptomap extended permit ip 192.168.2.0 255.255.254.0 192.168.4.0 255.255.254.0
access-list outside_4_cryptomap extended permit ip 192.168.2.0 255.255.254.0 192.168.8.0 255.255.254.0
access-list outside_5_cryptomap extended permit ip 192.168.2.0 255.255.254.0 192.168.16.0 255.255.254.0
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool GeoVPNPool 192.168.15.200-192.168.15.254 mask 255.255.254.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable 444
http 192.168.2.0 255.255.254.0 inside
http 0.0.0.0 0.0.0.0 inside
http 0.0.0.0 0.0.0.0 outside
http authentication-certificate inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 207.228.xx.xx
crypto map outside_map 1 set transform-set ESP-3DES-SHA
crypto map outside_map 2 match address outside_2_cryptomap
crypto map outside_map 2 set pfs
crypto map outside_map 2 set peer 208.119.xx.xx
crypto map outside_map 2 set transform-set ESP-3DES-SHA
crypto map outside_map 3 match address outside_3_cryptomap
crypto map outside_map 3 set pfs group1
crypto map outside_map 3 set peer 208.119.xx.xx
crypto map outside_map 3 set transform-set ESP-3DES-SHA
crypto map outside_map 4 match address outside_4_cryptomap
crypto map outside_map 4 set pfs
crypto map outside_map 4 set peer 208.119.xx.xx
crypto map outside_map 4 set transform-set ESP-3DES-SHA
crypto map outside_map 5 match address outside_5_cryptomap
crypto map outside_map 5 set pfs group1
crypto map outside_map 5 set peer 70.64.xx.xx
crypto map outside_map 5 set transform-set ESP-3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 0.0.0.0 0.0.0.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
management-access inside
dhcp-client client-id interface outside
dhcpd auto_config outside
dhcpd address 192.168.2.100-192.168.2.254 inside
dhcpd auto_config outside interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy VPNGeo internal
group-policy VPNGeo attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value VPNGeo_splitTunnelAcl
username user password shbn5zbLkuHP/mJX encrypted privilege 15
username namepassword vP98Lj8Vm5SLs9PW encrypted
username nameattributes
vpn-group-policy VPNGeo
tunnel-group 207.228.xx.xxtype ipsec-l2l
tunnel-group 207.228.xx.xxipsec-attributes
pre-shared-key *
tunnel-group VPNGeo type remote-access
tunnel-group VPNGeo general-attributes
address-pool GeoVPNPool
default-group-policy VPNGeo
tunnel-group VPNGeo ipsec-attributes
pre-shared-key *
tunnel-group 208.119.xx.xxtype ipsec-l2l
tunnel-group 208.119.xx.xxipsec-attributes
pre-shared-key *
tunnel-group 208.119.xx.xx type ipsec-l2l
tunnel-group 208.119.xx.xx ipsec-attributes
pre-shared-key *
tunnel-group 208.119.xx.xxtype ipsec-l2l
tunnel-group 208.119.xx.xxipsec-attributes
pre-shared-key *
tunnel-group 70.64.xx.xxtype ipsec-l2l
tunnel-group 70.64.xx.xxipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:e3adf4e597198f58cd21e508aabdbab9
: end -
Subnet mask 255.255.255.255 assigned to VPN client - can't ping LAN
Hi,
I configured PIX 501 with PPTP VPN to connect to the small office (PIX FW, Win 2000 Server, several Win clients, LAN IP 10.0.0.X/24):
ip local pool mypool 10.0.0.101-10.0.0.105
vpdn group mygroup accept dialin pptp
vpdn group mygroup ppp authentication mschap
vpdn group mygroup ppp encryption mppe 128 required
vpdn group mygroup client configuration address local mypool
vpdn group mygroup client configuration dns 10.0.0.15
vpdn group mygroup pptp echo 60
vpdn group mygroup client authentication local
vpdn username xxxx password *********
vpdn enable outside
I can connect to the office using Win VPN client, but I can't ping any hosts in the office network. I suspect that the reason for that is subnet mask assigned to the VPN client: 255.255.255.255. ipconfig of the VPN client:
PPP adapter Office:
Connection-specific DNS Suffix . :
IP Address. . . . . . . . . . . . : 10.0.0.101
Subnet Mask . . . . . . . . . . . : 255.255.255.255
Default Gateway . . . . . . . . . :
Default GW is missing too, but I think this is not the main problem.
Any way, what is wrong with my config? How to fix subnet mask assigned to clients? Or may be my assumption is wrong and this mask is ok? What is wrong then?
Any input will be greatly appreciated!
GeorgeThanks for the prompt reply.
Here it does:
PIX Version 6.3(4)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password xxxxxxxxxxxxxx encrypted
passwd xxxxxxxxxxxxxx encrypted
hostname OSTBERG-PIX
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list 80 permit ip 10.0.0.0 255.255.255.0 10.0.20.0 255.255.255.0
access-list inbound permit icmp any any
access-list inbound permit tcp any any eq pptp
access-list inbound permit gre any any
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside 66.189.xxx.xxx 255.255.252.0
ip address inside 10.0.0.23 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool mypool 10.0.0.101-10.0.0.105
pdm location 10.0.0.0 255.255.255.0 inside
pdm location 10.0.0.15 255.255.255.255 inside
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
access-group inbound in interface outside
route outside 0.0.0.0 0.0.0.0 66.189.yyy.yyy 1
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
sysopt connection permit-pptp
telnet 10.0.0.23 255.255.255.255 inside
telnet 10.0.0.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
vpdn group mygroup accept dialin pptp
vpdn group mygroup ppp authentication mschap
vpdn group mygroup ppp encryption mppe 128 required
vpdn group mygroup client configuration address local mypool
vpdn group mygroup client configuration dns 10.0.0.15
vpdn group mygroup pptp echo 60
vpdn group mygroup client authentication local
vpdn username ********* password *********
vpdn enable outside
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd auto_config outside
terminal width 80
Cryptochecksum:xxx
: end
There are remnants of old config, I just recently took over this network, some lines look odd to me, but I did not touch what works. VPN config is all mine.
PIX internal 10.0.0.23 - is a gateway for the network. DNS server in LAN - 10.0.0.15.
I've been reading about the problem and came across several posts that this subnet mask is normal, but it puzzles me - how can this host communicate with anyone else if there is no room for other hosts in this network (according to the mask)?!
Thanks again!
George -
Cisco ASA 5510 - Cisco Client Can Connect To VPN But Can't Ping!
Hi,
I have an ASA 5510 with the configuration below. I have configure the ASA as remote access vpn server with cisco vpn client, my problem now is I can connect but I can't ping.
Config
ciscoasa# sh run
: Saved
ASA Version 8.0(3)
hostname ciscoasa
enable password 5QB4svsHoIHxXpF/ encrypted
names
name xxx.xxx.xxx.xxx SAP_router_IP_on_SAP
name xxx.xxx.xxx.xxx ISA_Server_second_external_IP
name xxx.xxx.xxx.xxx Mail_Server
name xxx.xxx.xxx.xxx IncomingIP
name xxx.xxx.xxx.xxx SAP
name xxx.xxx.xxx.xxx WebServer
name xxx.xxx.xxx.xxx cms_eservices_projects_sharepointold
name 192.168.2.2 isa_server_outside
interface Ethernet0/0
nameif outside
security-level 0
ip address IncomingIP 255.255.255.248
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.253 255.255.255.0
management-only
passwd 123
ftp mode passive
clock timezone EEST 2
clock summer-time EEDT recurring last Sun Mar 3:00 last Sun Oct 4:00
object-group service TCP_8081 tcp
port-object eq 8081
object-group service DM_INLINE_TCP_1 tcp
port-object eq 3389
port-object eq ftp
port-object eq www
port-object eq https
port-object eq smtp
port-object eq pop3
port-object eq 3200
port-object eq 3300
port-object eq 3600
port-object eq 3299
port-object eq 3390
port-object eq 50000
port-object eq 3396
port-object eq 3397
port-object eq 3398
port-object eq imap4
port-object eq 587
port-object eq 993
port-object eq 8000
port-object eq 8443
port-object eq telnet
port-object eq 3901
group-object TCP_8081
port-object eq 1433
port-object eq 3391
port-object eq 3399
port-object eq 8080
port-object eq 3128
port-object eq 3900
port-object eq 3902
port-object eq 7777
port-object eq 3392
port-object eq 3393
port-object eq 3394
port-object eq 3395
port-object eq 92
port-object eq 91
port-object eq 3206
port-object eq 8001
port-object eq 8181
port-object eq 7778
port-object eq 8180
port-object eq 22222
port-object eq 11001
port-object eq 11002
port-object eq 1555
port-object eq 2223
port-object eq 2224
object-group service RDP tcp
port-object eq 3389
object-group service 3901 tcp
description 3901
port-object eq 3901
object-group service 50000 tcp
description 50000
port-object eq 50000
object-group service Enable_Transparent_Tunneling_UDP udp
port-object eq 4500
access-list inside_access_in remark connection to SAP
access-list inside_access_in extended permit ip 192.168.2.0 255.255.255.0 host SAP_router_IP_on_SAP
access-list inside_access_in remark VPN Outgoing - PPTP
access-list inside_access_in extended permit tcp 192.168.2.0 255.255.255.0 any eq pptp
access-list inside_access_in remark VPN Outgoing - GRE
access-list inside_access_in extended permit gre 192.168.2.0 255.255.255.0 any
access-list inside_access_in remark VPN - GRE
access-list inside_access_in extended permit gre any any
access-list inside_access_in remark VPN Outgoing - IKE Client
access-list inside_access_in extended permit udp 192.168.2.0 255.255.255.0 any eq isakmp
access-list inside_access_in remark VPN Outgoing - IPSecNAT - T
access-list inside_access_in extended permit udp 192.168.2.0 255.255.255.0 any eq 4500
access-list inside_access_in remark DNS Outgoing
access-list inside_access_in extended permit udp any any eq domain
access-list inside_access_in remark DNS Outgoing
access-list inside_access_in extended permit tcp any any eq domain
access-list inside_access_in remark Outoing Ports
access-list inside_access_in extended permit tcp 192.168.2.0 255.255.255.0 any object-group DM_INLINE_TCP_1
access-list inside_access_in extended permit ip 172.16.1.0 255.255.255.0 any
access-list outside_access_in extended permit ip any any
access-list outside_access_in extended permit tcp any any eq pptp
access-list outside_access_in extended permit gre any any
access-list outside_access_in extended permit gre any host Mail_Server
access-list outside_access_in extended permit tcp any host Mail_Server eq pptp
access-list outside_access_in extended permit esp any any
access-list outside_access_in extended permit ah any any
access-list outside_access_in extended permit udp any any eq isakmp
access-list outside_access_in extended permit udp any any object-group Enable_Transparent_Tunneling_UDP
access-list VPN standard permit 192.168.2.0 255.255.255.0
access-list corp_vpn extended permit ip 192.168.2.0 255.255.255.0 172.16.1.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu management 1500
ip local pool POOL 172.16.1.10-172.16.1.20 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-603.bin
no asdm history enable
arp timeout 14400
nat-control
global (outside) 2 Mail_Server netmask 255.0.0.0
global (outside) 1 interface
global (inside) 2 interface
nat (inside) 0 access-list corp_vpn
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp Mail_Server 8001 ISA_Server_second_external_IP 8001 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 8000 ISA_Server_second_external_IP 8000 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server pptp isa_server_outside pptp netmask 255.255.255.255
static (inside,outside) tcp Mail_Server smtp isa_server_outside smtp netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 587 isa_server_outside 587 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 9444 isa_server_outside 9444 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 9443 isa_server_outside 9443 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 3389 isa_server_outside 3389 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 3390 isa_server_outside 3390 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 3901 isa_server_outside 3901 netmask 255.255.255.255
static (inside,outside) tcp SAP 50000 isa_server_outside 50000 netmask 255.255.255.255
static (inside,outside) tcp SAP 3200 isa_server_outside 3200 netmask 255.255.255.255
static (inside,outside) tcp SAP 3299 isa_server_outside 3299 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server www isa_server_outside www netmask 255.255.255.255
static (inside,outside) tcp Mail_Server https isa_server_outside https netmask 255.255.255.255
static (inside,outside) tcp Mail_Server pop3 isa_server_outside pop3 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server imap4 isa_server_outside imap4 netmask 255.255.255.255
static (inside,outside) tcp cms_eservices_projects_sharepointold 9999 isa_server_outside 9999 netmask 255.255.255.255
static (inside,outside) 192.168.2.0 access-list corp_vpn
access-group outside_access_in in interface outside
access-group inside_access_in in interface inside
route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.2.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 management
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set transet esp-des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map dynmap 10 set pfs
crypto dynamic-map dynmap 10 set transform-set transet ESP-3DES-SHA
crypto map cryptomap 10 ipsec-isakmp dynamic dynmap
crypto map cryptomap interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
no crypto isakmp nat-traversal
telnet 192.168.2.0 255.255.255.0 inside
telnet 192.168.1.0 255.255.255.0 management
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd dns xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx interface inside
dhcpd domain domain.local interface inside
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics access-list
tftp-server management 192.168.1.123 /
group-policy mypolicy internal
group-policy mypolicy attributes
split-tunnel-policy tunnelspecified
split-tunnel-network-list value VPN
username vpdn password 123
username vpdn attributes
vpn-group-policy mypolicy
service-type remote-access
tunnel-group mypolicy type remote-access
tunnel-group mypolicy general-attributes
address-pool POOL
default-group-policy mypolicy
tunnel-group mypolicy ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect pptp
service-policy global_policy global
prompt hostname context
Cryptochecksum:b8bb19b6cb05cfa9ee125ad7bc5444ac
: end
Thank you very much.Here is the output:
ciscoasa# packet-tracer input outside icmp 172.16.1.10 8 0 192.168.2.1
Phase: 1
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
Phase: 2
Type: UN-NAT
Subtype: static
Result: ALLOW
Config:
static (inside,outside) 192.168.2.0 access-list corp_vpn
nat-control
match ip inside 192.168.2.0 255.255.255.0 outside 172.16.1.0 255.255.255.0
static translation to 192.168.2.0
translate_hits = 0, untranslate_hits = 139
Additional Information:
NAT divert to egress interface inside
Untranslate 192.168.2.0/0 to 192.168.2.0/0 using netmask 255.255.255.0
Phase: 3
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group outside_access_in in interface outside
access-list outside_access_in extended permit ip any any
Additional Information:
Phase: 4
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 5
Type: CP-PUNT
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 6
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
class-map inspection_default
match default-inspection-traffic
policy-map global_policy
class inspection_default
inspect icmp
service-policy global_policy global
Additional Information:
Phase: 7
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
Additional Information:
Phase: 8
Type: VPN
Subtype: ipsec-tunnel-flow
Result: ALLOW
Config:
Additional Information:
Phase: 9
Type: NAT-EXEMPT
Subtype: rpf-check
Result: ALLOW
Config:
Additional Information:
Phase: 10
Type: NAT
Subtype: rpf-check
Result: ALLOW
Config:
static (inside,outside) 192.168.2.0 access-list corp_vpn
nat-control
match ip inside 192.168.2.0 255.255.255.0 outside 172.16.1.0 255.255.255.0
static translation to 192.168.2.0
translate_hits = 0, untranslate_hits = 140
Additional Information:
Phase: 11
Type: ACCESS-LIST
Subtype:
Result: DROP
Config:
Implicit Rule
Additional Information:
Result:
input-interface: outside
input-status: up
input-line-status: up
output-interface: inside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule -
Can't ping other server and more.
This is a weird one. I have a few problems going on. I have 2 netware 6.5 servers. My BM3.9 sp1 server is on Netware 6.5sp7 and my other server is Groupwise 7.03 on Netware 6.5sp6. My Groupwise server is strictly used for Groupwise. My BM3.9 server runs everything else for my enviornment; it is our main server for all of our data. I can vpn into and login to my BM server with no problems; however I can't ping or connect to the Groupwise server. Also I can't ping any internal workstations through the vpn. And what is even weirder is that I can't ping the private IP address of the BM3.9 server and yet I can log into it. I have the default address set up on the Groupwise to point to the private address of the BM server. I have the default address setup on the BM server to point to the ISP router that we have in our office. Also I can't browse the internet when I'm connected to the vpn and I do have as my last traffic rule to not encrypt (bypass). I have noticed that when I'm connected to the vpn that my dns settings on my laptop change to the office dns and yet I have not configured dns to be pushed through the vpn. One more thing, I have set up the hosts file on my laptop to point to internal computers. Any help is greatly appreciated.
Thanks in advance.Originally Posted by Mysterious
Sksgl wrote:
> This is a weird one. I have a few problems going on. I have 2 netware
> 6.5 servers. My BM3.9 sp1 server is on Netware 6.5sp7 and my other
> server is Groupwise 7.03 on Netware 6.5sp6. My Groupwise server is
> strictly used for Groupwise. My BM3.9 server runs everything else for
> my enviornment; it is our main server for all of our data. I can vpn
> into and login to my BM server with no problems; however I can't ping or
> connect to the Groupwise server. Also I can't ping any internal
> workstations through the vpn. And what is even weirder is that I can't
> ping the private IP address of the BM3.9 server and yet I can log into
> it. I have the default address set up on the Groupwise to point to the
> private address of the BM server. I have the default address setup on
> the BM server to point to the ISP router that we have in our office.
> Also I can't browse the internet when I'm connected to the vpn and I do
> have as my last traffic rule to not encrypt (bypass). I have noticed
> that when I'm connected to the vpn that my dns settings on my laptop
> change to the office dns and yet I have not configured dns to be pushed
> through the vpn. One more thing, I have set up the hosts file on my
> laptop to point to internal computers. Any help is greatly
> appreciated.
>
> Thanks in advance.
>
>
Wrong traffic rules?
I have gone over and over the traffic rules that are listed in Craig's book and have followed them exactly. My first rule in an admin to all rule that applys to me and the destination is to the network.
Thanks. -
I can connect my cisco mobile vpn but can't ping & access internal IP
Hi somebody,
i've configured mobile vpn configuration in cisco 7200 with GNS3. i can connect VPN to my cisco router with cisco vpn client software from outside. but i can't ping to internal ip and can't access internal resources.
My Internal IP is 192.168.1.x . And IP for mobile VPN client from outside is 172.60.1.x.
Your advise will be appreciate.
here is my configuration with cisco 7200 in GNS 3,
OfficeVPN_Router#sh run
Building configuration...
Current configuration : 2186 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname OfficeVPN_Router
boot-start-marker
boot-end-marker
enable secret 5 $1$E0Gz$U8UzNtHOXy2CeoEFj30by0
aaa new-model
aaa authentication login userlist local
aaa authorization network grouplist local
aaa session-id common
ip cef
no ip domain lookup
username asm privilege 15 password 0 pncsadmin
username user privilege 15 password 0 pncsadmin
username user1 privilege 15 password 0 pncsadmin
username cisco123 secret 5 $1$lCOc$Db.e8AFd/0f02ZI4/aeV./
crypto isakmp policy 10
encr aes
authentication pre-share
group 2
crypto isakmp client configuration group MWG
key cisco
dns 165.21.83.88
pool vpnpool
acl 101
netmask 255.255.0.0
crypto ipsec transform-set myset esp-aes esp-sha-hmac
crypto dynamic-map dynmap 10
set transform-set myset
reverse-route
crypto map mymap client authentication list userlist
crypto map mymap isakmp authorization list grouplist
crypto map mymap client configuration address initiate
crypto map mymap client configuration address respond
crypto map mymap 10 ipsec-isakmp dynamic dynmap
interface FastEthernet0/0
no ip address
shutdown
duplex half
interface FastEthernet1/0
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex full
speed 100
interface FastEthernet1/1
ip address 200.200.200.200 255.255.255.0
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map mymap
ip local pool vpnpool 172.60.1.10 172.60.1.100
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 200.200.200.201
no ip http server
no ip http secure-server
ip nat inside source list 111 interface FastEthernet1/1 overload
access-list 101 permit ip 192.168.1.0 0.0.0.255 172.60.0.0 0.0.255.255
access-list 111 deny ip 192.168.1.0 0.0.0.255 172.60.0.0 0.0.255.255
access-list 111 permit ip any any
control-plane
gatekeeper
shutdown
line con 0
exec-timeout 0 0
password cisco123
logging synchronous
stopbits 1
line aux 0
stopbits 1
line vty 0 4
password cisco123
end
OfficeVPN_Router#sh ver
Cisco IOS Software, 7200 Software (C7200-A3JK9S-M), Version 12.4(25), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Tue 21-Apr-09 18:50 by prod_rel_team
ROM: ROMMON Emulation Microcode
BOOTLDR: 7200 Software (C7200-A3JK9S-M), Version 12.4(25), RELEASE SOFTWARE (fc2)
OfficeVPN_Router uptime is 30 minutes
System returned to ROM by unknown reload cause - suspect boot_data[BOOT_COUNT] 0x0, BOOT_COUNT 0, BOOTDATA 19
System image file is "tftp://255.255.255.255/unknown"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco 7206VXR (NPE400) processor (revision A) with 245760K/16384K bytes of memory.
Processor board ID 4279256517
R7000 CPU at 150MHz, Implementation 39, Rev 2.1, 256KB L2 Cache
6 slot VXR midplane, Version 2.1
Last reset from power-on
PCI bus mb0_mb1 (Slots 0, 1, 3 and 5) has a capacity of 600 bandwidth points.
Current configuration on bus mb0_mb1 has a total of 600 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
PCI bus mb2 (Slots 2, 4, 6) has a capacity of 600 bandwidth points.
Current configuration on bus mb2 has a total of 0 bandwidth points
This configuration is within the PCI bus capacity and is supported.
Please refer to the following document "Cisco 7200 Series Port Adaptor
Hardware Configuration Guidelines" on Cisco.com <http://www.cisco.com>
for c7200 bandwidth points oversubscription and usage guidelines.
3 FastEthernet interfaces
125K bytes of NVRAM.
65536K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
8192K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x2102
OfficeVPN_Router#Dear Javier ,
Thanks for your info. i already tested as you say. but still i can't use & ping to my internal IP which is behind cisco VPN router. i posted my config file.
OfficeVPN_Router(config)#ip access-list resequence 111 10 10
OfficeVPN_Router(config)#do sh run
Building configuration...
Current configuration : 2201 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname OfficeVPN_Router
boot-start-marker
boot-end-marker
enable secret 5 $1$E0Gz$U8UzNtHOXy2CeoEFj30by0
aaa new-model
aaa authentication login userlist local
aaa authorization network grouplist local
aaa session-id common
ip cef
no ip domain lookup
username asm privilege 15 password 0 pncsadmin
username user privilege 15 password 0 pncsadmin
username user1 privilege 15 password 0 pncsadmin
username cisco123 secret 5 $1$lCOc$Db.e8AFd/0f02ZI4/aeV./
crypto isakmp policy 10
encr aes
authentication pre-share
group 2
crypto isakmp client configuration group MWG
key cisco
dns 165.21.83.88
pool vpnpool
acl 101
netmask 255.255.0.0
crypto ipsec transform-set myset esp-aes esp-sha-hmac
crypto dynamic-map dynmap 10
set transform-set myset
reverse-route
crypto map mymap client authentication list userlist
crypto map mymap isakmp authorization list grouplist
crypto map mymap client configuration address initiate
crypto map mymap client configuration address respond
crypto map mymap 10 ipsec-isakmp dynamic dynmap
interface FastEthernet0/0
no ip address
shutdown
duplex half
interface FastEthernet1/0
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex full
speed 100
interface FastEthernet1/1
ip address 200.200.200.200 255.255.255.0
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map mymap
ip local pool vpnpool 172.60.1.10 172.60.1.100
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 200.200.200.201
no ip http server
no ip http secure-server
ip nat inside source list 111 interface FastEthernet1/1 overload
access-list 101 permit ip 192.168.1.0 0.0.0.255 172.60.0.0 0.0.255.255
access-list 111 deny ip 192.168.1.0 0.0.0.255 172.60.0.0 0.0.255.255
access-list 111 permit ip 192.168.1.0 0.0.0.255 any
control-plane
gatekeeper
shutdown
line con 0
exec-timeout 0 0
password cisco123
logging synchronous
stopbits 1
line aux 0
stopbits 1
line vty 0 4
password cisco123
end -
VPN client connected to VPN but can't ping or access to server
HI ,
i need help urgently, had been troubleshooting for a day, but have no ideal what wrong with the config.
Basically there is 2 set of VPN configured, one is site to site IPSEC VPN and another one is connect via VPN client software coexist in same router.
This recently we having problem on client can't access or ping to internal server which is 192.168.6.3 from VPN client software.
VPN client will connect to VPN ip pool as10.20.1.0 to 10.20.1.100
Software itself shown connected but request time out when ping.
Below is the config. Some of the command might be extra as when i did some test, but end up didn't work.
aaa new-model
aaa authentication login userauthen local
aaa authorization network adminmap group VPNClient
aaa authorization network groupauthor local
aaa authorization network map-singapore local
crypto isakmp policy 10
encr 3des
authentication pre-share
group 2
crypto isakmp key emptyspace address 203.142.83.218 no-xauth
crypto isakmp keepalive 15 periodic
crypto isakmp client configuration address-pool local ippool
crypto isakmp client configuration group map-singapore
key cisco123
dns 192.168.6.3
domain cisco.com
pool ippool
acl 102
crypto isakmp profile VPNclient
match identity address 27.54.43.210 255.255.255.255
match identity group vpnclient
client authentication list userauthen
client configuration address respond
crypto ipsec security-association idle-time 86400
crypto ipsec transform-set REMSET esp-3des esp-md5-hmac
crypto ipsec transform-set DYNSET esp-aes esp-md5-hmac
crypto ipsec transform-set esp-3des-sha esp-3des esp-sha-hmac
crypto dynamic-map dynmap 10
set transform-set DYNSET
set isakmp-profile VPNclient
reverse-route
crypto map VPNMAP client authentication list userauthen
crypto map VPNMAP isakmp authorization list map-singapore
crypto map VPNMAP client configuration address respond
crypto map VPNMAP 10 ipsec-isakmp dynamic dynmap
crypto map VPNMAP 11 ipsec-isakmp
description VPN to ASA5520
set peer 203.142.83.218
set security-association lifetime kilobytes 14608000
set security-association lifetime seconds 86400
set transform-set REMSET
match address 100
interface GigabitEthernet0/0
ip address 27.54.43.210 255.255.255.240
ip nat outside
no ip virtual-reassembly
duplex full
speed 100
crypto map VPNMAP
interface GigabitEthernet0/1
ip address 192.168.6.1 255.255.255.0
ip nat inside
no ip virtual-reassembly
duplex full
speed 100
interface GigabitEthernet0/2
description $ES_LAN$
no ip address
shutdown
duplex auto
speed auto
ip local pool ippool 10.20.1.0 10.20.1.100
ip forward-protocol nd
ip pim bidir-enable
no ip http server
ip http authentication local
no ip http secure-server
ip nat inside source list 1 interface GigabitEthernet0/0 overload
ip nat inside source list 101 interface GigabitEthernet0/0 overload
ip nat inside source route-map nonat interface GigabitEthernet0/0 overload
ip nat inside source static 192.168.6.3 27.54.43.212
ip route 0.0.0.0 0.0.0.0 27.54.43.209
ip route 192.168.1.0 255.255.255.0 27.54.43.209
ip route 192.168.151.0 255.255.255.0 192.168.6.151
ip route 192.168.208.0 255.255.255.0 27.54.43.209
ip access-list extended RA_SING
permit ip 192.168.6.0 0.0.0.255 192.168.1.0 0.0.0.255
permit ip 192.168.6.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 10.0.0.0 0.255.255.255 192.168.6.0 0.0.0.255
permit ip 192.168.6.0 0.0.0.255 192.168.208.0 0.0.0.255
permit ip 10.20.1.1 0.0.0.100 192.168.6.0 0.0.0.255
permit ip 10.20.1.0 0.0.0.255 10.0.0.0 0.255.255.255
deny ip any any log
access-list 1 remark Local Network
access-list 1 permit 192.168.6.0 0.0.0.255
access-list 1 permit 192.168.102.0 0.0.0.255
access-list 1 permit 192.168.151.0 0.0.0.255
access-list 2 remark VPNClient-range
access-list 2 permit 10.0.0.0 0.255.255.255
access-list 10 permit 192.168.6.0 0.0.0.255
access-list 10 permit 192.168.102.0 0.0.0.255
access-list 10 permit 192.168.151.0 0.0.0.255
access-list 10 permit 10.0.0.0 0.255.255.255
access-list 100 permit ip 192.168.6.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 100 permit ip 192.168.102.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 100 permit ip 192.168.6.0 0.0.0.255 192.168.208.0 0.0.0.255
access-list 100 permit ip host 192.168.6.7 host 192.168.208.48
access-list 101 deny ip 192.168.6.0 0.0.0.255 10.0.0.0 0.255.255.255
access-list 101 permit ip 10.0.0.0 0.255.255.255 any
access-list 101 permit ip 192.168.6.0 0.0.0.255 any
access-list 102 permit ip 10.0.0.0 0.255.255.255 any
access-list 120 deny ip any any log
access-list 120 deny ip 192.168.6.0 0.0.0.255 192.168.1.0 0.0.0.255 log
access-list 120 deny ip 192.168.6.0 0.0.0.255 10.0.0.0 0.255.255.255
access-list 120 deny ip 192.168.6.0 0.0.0.255 192.168.208.0 0.0.0.255
no cdp run
route-map nonat permit 10
match ip address 120
control-plane
alias isakmp-profile sh crypto isakmp sa
alias exec ipsec sh crypto ipsec sa
banner motd ^CC^CI did not try to ping 4.2.2.2. I just know I can not ping comcasts dns servers. I have updated the firmware on the router and it did not work. The computer was able to access the internet until about a week ago, I don't understand what could have changed that I would now need a static DNS.
-
Hi!
I wish someone can help me on this, I'm a new guy on cisco firewalls and I'm currently implementing cisco asa 5512x, here are the details:
ISP -> Firewall -> Core switch -> Internal LAN
after installing the cisco asa and terminating the appropriate lan for the outside and inside interfaces, internet seems intermittent and cisco vpn client can connect with internet connection but can't ping internal LAN.
here's my configuration from my firewall.
ASA Version 8.6(1)2
hostname ciscofirewall
enable password 2KFQnbNIdI.2KYOU encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address 203.x.x.x 255.255.255.0
interface GigabitEthernet0/1
nameif inside
security-level 100
ip address 10.152.11.15 255.255.255.0
interface GigabitEthernet0/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
management-only
ftp mode passive
dns domain-lookup outside
dns domain-lookup inside
dns server-group DefaultDNS
name-server 4.2.2.2 -------> public DNS
name-server 8.8.8.8 -------> public
name-server 203.x.x.x ----> Clients DNS
name-server 203.x.x.x -----> Clients DNS
same-security-traffic permit intra-interface
object network net_access
subnet 10.0.0.0 255.0.0.0
object network citrix_server
host 10.152.11.21
object network NETWORK_OBJ_10.10.10.0_28
subnet 10.10.10.0 255.255.255.240
object network NETWORK_OBJ_10.0.0.0_8
subnet 10.0.0.0 255.0.0.0
object network InterconHotel
subnet 10.152.11.0 255.255.255.0
access-list net_surf extended permit ip any any
access-list net_surf extended permit ip object NETWORK_OBJ_10.10.10.0_28 object InterconHotel
access-list outside_access extended permit tcp any object citrix_server eq www
access-list outside_access extended permit ip object NETWORK_OBJ_10.10.10.0_28 any
access-list outsidevpn_splitTunnelAcl standard permit 10.152.11.0 255.255.255.0
access-list LAN_Users remark LAN_clients
access-list LAN_Users standard permit any
access-list vpnpool extended permit ip 10.10.10.0 255.255.255.248 any
pager lines 24
logging enable
logging asdm informational
mtu management 1500
mtu outside 1500
mtu inside 1500
ip local pool vpnpool 10.10.10.1-10.10.10.6 mask 255.255.255.248
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source static NETWORK_OBJ_10.10.10.0_28 NETWORK_OBJ_10.10.10.0_28 destination static NETWORK_OBJ_10.10.10.0_28 NETWORK_OBJ_10.10.10.0_28 no-proxy-arp route-lookup
object network net_access
nat (inside,outside) dynamic interface
object network citrix_server
nat (inside,outside) static 203.177.18.234 service tcp www www
object network NETWORK_OBJ_10.10.10.0_28
nat (any,outside) dynamic interface
object network InterconHotel
nat (inside,outside) dynamic interface dns
access-group outside_access in interface outside
access-group net_surf out interface outside
route outside 0.0.0.0 0.0.0.0 203.x.x.x 1
route outside 10.10.10.0 255.255.255.248 10.152.11.15 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication telnet console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 10.0.0.100 255.255.255.255 inside
http 10.10.10.0 255.255.255.240 outside
http 0.0.0.0 0.0.0.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto ikev1 enable outside
crypto ikev1 enable inside
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
client-update enable
telnet 10.152.11.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.1.2-192.168.1.254 management
dhcpd enable management
threat-detection basic-threat
threat-detection statistics
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
webvpn
enable outside
anyconnect-essentials
group-policy outsidevpn internal
group-policy outsidevpn attributes
dns-server value 203.x.x.x 203.x.x.x
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client
split-tunnel-policy tunnelall
split-tunnel-network-list value outsidevpn_splitTunnelAcl
default-domain value interconti.com
address-pools value vpnpool
username test1 password i1lji/GiOWB67bAs encrypted privilege 5
username test1 attributes
vpn-group-policy outsidevpn
username mnlha password WlzjmENGEEZmT9LA encrypted
username mnlha attributes
vpn-group-policy outsidevpn
username cisco password 3USUcOPFUiMCO4Jk encrypted privilege 15
tunnel-group outsidevpn type remote-access
tunnel-group outsidevpn general-attributes
address-pool (inside) vpnpool
address-pool vpnpool
authentication-server-group (outside) LOCAL
default-group-policy outsidevpn
tunnel-group outsidevpn ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
inspect http
inspect ipsec-pass-thru
class class-default
user-statistics accounting
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
hpm topN enable
Cryptochecksum:edc30dda08e5800fc35b72dd6e1d88d7
: end
thanks. please help.I think you should change your nat-exemption rule to smth more general, like
nat (inside,outside) source static any any destination static NETWORK_OBJ_10.10.10.0_28 NETWORK_OBJ_10.10.10.0_28 no-proxy-arp route-lookup
'cause your inside networks are not the same as your vpn-pool subnet.
Plus, if you're trying to reach inside subnets, different from 10.152.11.0 255.255.255.0 (ip from wich subnet is assignet to your inside interface, and for wich above nat exception should be enough), you should check if routing is configured from that subnets to your vpn-pool-subnet through the ASA. -
I will include a post of my config. I have the clients connecting through the VPN tunnel on the 180.0.0.0/24 network, 192.168.1.0/24 is the primary network for the office.
I can connect to the VPN and I do recieve the correct address assignment. I belive tunneling may be setup correct in the aspect that I can still connect to the internet while on the VPN, but I can not ping any hosts on the 192.168.1.0 network. In the debug log from the ASDM I can see pings reaching the ASA, but no responce is received on the client.
6
Feb 21 2013
21:54:26
180.0.0.1
53508
192.168.1.1
0
Built inbound ICMP connection for faddr 180.0.0.1/53508 gaddr 192.168.1.1/0 laddr 192.168.1.1/0 (christopher)
Any help would be greatly appreciated, I am currently presuring my CCNP so I would like to get a deeper understanding of how to solve these issues.
-Chris
hostname RegencyRE-ASA
domain-name regencyrealestate.info
enable password 2/VA7dRFkv6fjd1X encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 180.0.0.0 Regency
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
description link to REGENCYSERVER
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
description link to RegencyRE-AP
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.120 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address x.x.x.x 255.255.255.248
ftp mode passive
clock timezone PST -8
clock summer-time PDT recurring
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
name-server 208.67.220.220
name-server 208.67.222.222
domain-name regencyrealestate.info
access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 Regency 255.255.255.224
access-list RegencyRE_splitTunnelAcl standard permit 192.168.1.0 255.255.255.0
access-list outside_access_in extended permit icmp any any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool Regency 180.0.0.1-180.0.0.20 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any outside
asdm location Regency 255.255.255.0 inside
asdm location 192.168.0.0 255.255.0.0 inside
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 12.186.110.2 1
route inside 192.0.0.0 255.0.0.0 192.168.1.102 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
aaa authentication serial console LOCAL
http server enable 8443
http 0.0.0.0 0.0.0.0 outside
http 0.0.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 inside
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 15
ssh version 2
console timeout 0
dhcprelay server 192.168.1.102 inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 69.25.96.13 source outside prefer
ntp server 216.171.124.36 source outside prefer
webvpn
group-policy RegencyRE internal
group-policy RegencyRE attributes
dns-server value 208.67.220.220 208.67.222.222
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value RegencyRE_splitTunnelAcl
username adriana password encrypted privilege 0
username christopher password encrypted privilege 15
username irene password encrypted privilege 0
tunnel-group RegencyRE type remote-access
tunnel-group RegencyRE general-attributes
address-pool Regency
default-group-policy RegencyRE
tunnel-group RegencyRE ipsec-attributes
pre-shared-key R3&eNcY1.
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:35bc3a41701f7f8e9dde5fa35532896d
: endLooking at a previous ASA 5520 I configured when I ping hosts I see the following in the logs. I know there is something obvious I am missing.
6
Feb 21 2013
22:01:49
302020
170.0.0.1
13317
172.16.0.253
0
Built inbound ICMP connection for faddr 170.0.0.1/13317 gaddr 172.16.0.253/0 laddr 172.16.0.253/0 (cxv1)
6
Feb 21 2013
22:01:49
302020
172.16.0.253
0
170.0.0.1
13317
Built outbound ICMP connection for faddr 170.0.0.1/13317 gaddr 172.16.0.253/0 laddr 172.16.0.253/0 -
Quickvpn / client to gateway vpn rv042 can only ping router
I am setting up remote access using an RV042 router. Using quickvpn or a client-to gateway vpn and shrewsoft client, I can only access/ping the LAN side of the remote router and one machine on the remote network. The PPTP server and native Windows 7 connection provide access to all machines on the remote network.
I have 2 possible reasons for this and would like to find the real reason:
1) The remote RV042 is behind another router, and that router restricts access other than the PPTP traffic.
2) The VPN tunnels other than PPTP only allow access to the remote LAN side of the router and remote machines that have the remote router defined as their gateway in the IP configuration.
Any ideas?I've narrowed the problem down to option 2 above. If I change the gateway of a LAN resource to point to the LAN side of the router, it can be accessed through the VPN tunnel.
I haven't had time to see if adding routing entries can fix this problem. Any suggestions will be appreciated.
Also, I would appreciate an explanation of why the PPTP connection works. I will research this myself (eventually) but am already backed up with other projects.. -
Connect to VPN but can't ping past inside interface
Hello,
I've been working on this issue for a few days with no success. We're setting up a new Cisco ASA 5515 in our environment and are trying to get a simple IPSec VPN setup on it for remote access. After some initial problems, we've gotten it to where the VPN tunnel authenticates the user and connects as it should, however we cannot ping into our LAN. We are able to ping as far as the firewall's inside interface. I've tried other types of traffic too and nothing gets through. I've checked the routes listed on the VPN client while we're connected and they look correct - the client also shows both sent and received bytes when we connect using TCP port 10000, but no Received bytes when we connect using UDP 4500. We are trying to do split tunneling, and that seems to be setup correctly because I can still surf while the VPN is connected.
Below is our running config. Please excuse any messyness in the config as there are a couple of us working on it and we've been trying a whole bunch of different settings throughout the troubleshooting process. I will also note that we're using ASDM as our primary method of configuring the unit, so any suggestions that could be made with that in mind would be most helpful. Thanks!
ASA-01# sh run
: Saved
ASA Version 8.6(1)2
hostname ASA-01
domain-name domain.org
enable password **** encrypted
passwd **** encrypted
names
interface GigabitEthernet0/0
speed 100
duplex full
nameif inside
security-level 100
ip address 10.2.0.1 255.255.0.0
interface GigabitEthernet0/1
description Primary WAN Interface
nameif outside
security-level 0
ip address 76.232.211.169 255.255.255.192
interface GigabitEthernet0/2
shutdown
<--- More --->
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
shutdown
no nameif
no security-level
no ip address
interface Management0/0
speed 100
<--- More --->
duplex full
shutdown
nameif management
security-level 100
ip address 10.4.0.1 255.255.0.0
ftp mode passive
clock timezone MST -7
clock summer-time MDT recurring
dns domain-lookup inside
dns server-group DefaultDNS
name-server 10.2.11.6
domain-name domain.org
dns server-group sub
name-server 10.2.11.121
name-server 10.2.11.138
domain-name sub.domain.net
same-security-traffic permit intra-interface
object network 76.232.211.132
host 76.232.211.132
object network 10.2.11.138
host 10.2.11.138
object network 10.2.11.11
host 10.2.11.11
<--- More --->
object service DB91955443
service tcp destination eq 55443
object service 113309
service tcp destination range 3309 8088
object service 11443
service tcp destination eq https
object service 1160001
service tcp destination range 60001 60008
object network LAN
subnet 10.2.0.0 255.255.0.0
object network WAN_PAT
host 76.232.211.170
object network Test
host 76.232.211.169
description test
object network NETWORK_OBJ_10.2.0.0_16
subnet 10.2.0.0 255.255.0.0
object network NETWORK_OBJ_10.2.250.0_24
subnet 10.2.250.0 255.255.255.0
object network VPN_In
subnet 10.3.0.0 255.255.0.0
description VPN User Network
object-group service 11
service-object object 113309
<--- More --->
service-object object 11443
service-object object 1160001
object-group service IPSEC_VPN udp
port-object eq 4500
port-object eq isakmp
access-list outside_access_in extended permit icmp object VPN_In 10.2.0.0 255.255.0.0 traceroute log disable
access-list outside_access_in extended permit object-group 11 object 76.232.211.132 interface outside
access-list outside_access_in extended permit object DB91955443 any interface outside
access-list outside_access_in extended permit udp any object Test object-group IPSEC_VPN inactive
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended deny ip any any
access-list inside_access_in extended permit ip any any log disable
access-list inside_access_in extended permit icmp any any echo-reply log disable
access-list inside_access_in extended permit ip object VPN_In 10.2.0.0 255.255.0.0 log disable
access-list domain_splitTunnelAcl standard permit 10.2.0.0 255.255.0.0
access-list domain_splitTunnelAcl standard permit 10.3.0.0 255.255.0.0
access-list vpn_access_in extended permit ip any any
pager lines 24
logging enable
logging asdm informational
mtu management 1500
mtu inside 1500
mtu outside 1500
ip local pool VPNUsers 10.3.0.1-10.3.0.254 mask 255.255.0.0
<--- More --->
no failover
icmp unreachable rate-limit 1 burst-size 1
icmp permit any management
icmp permit any inside
icmp permit any outside
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic any interface
nat (inside,outside) source dynamic any WAN_PAT inactive
nat (outside,outside) source static 76.232.211.132 76.232.211.132 destination static interface 10.2.11.11 service 113309 113309
nat (outside,outside) source static 76.232.211.132 76.232.211.132 destination static interface 10.2.11.11 service 11443 11443
nat (outside,outside) source static 76.232.211.132 76.232.211.132 destination static interface 10.2.11.11 service 1160001 1160001
nat (outside,outside) source static any any destination static interface 10.2.11.138 service DB91955443 DB91955443
nat (inside,outside) source static NETWORK_OBJ_10.2.0.0_16 NETWORK_OBJ_10.2.0.0_16 destination static NETWORK_OBJ_10.2.250.0_24 NETWORK_OBJ_10.2.250.0_24 no-proxy-arp route-lookup
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 76.232.211.129 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
<--- More --->
dynamic-access-policy-record DfltAccessPolicy
aaa-server ActiveDirectory protocol nt
aaa-server ActiveDirectory (inside) host 10.2.11.121
nt-auth-domain-controller sub.domain.net
aaa-server ActiveDirectory (inside) host 10.2.11.138
nt-auth-domain-controller sub.domain.net
user-identity default-domain LOCAL
eou allow none
http server enable
http 10.4.0.0 255.255.255.0 management
http 10.2.0.0 255.255.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
no sysopt connection permit-vpn
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
<--- More --->
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto ca trustpoint ASDM_TrustPoint0
enrollment self
<--- More --->
subject-name CN=ASA-01
crl configure
crypto ca certificate chain ASDM_TrustPoint0
certificate a6c98751
308201f1 3082015a a0030201 020204a6 c9875130 0d06092a 864886f7 0d010105
0500303d 31153013 06035504 03130c43 5248442d 4d432d46 57303131 24302206
092a8648 86f70d01 09021615 43524844 2d4d432d 46573031 2e637268 642e6f72
67301e17 0d313330 35303730 32353232 325a170d 32333035 30353032 35323232
5a303d31 15301306 03550403 130c4352 48442d4d 432d4657 30313124 30220609
2a864886 f70d0109 02161543 5248442d 4d432d46 5730312e 63726864 2e6f7267
30819f30 0d06092a 864886f7 0d010101 05000381 8d003081 89028181 00c23d5f
acbf2b3f 9fe6e3c9 1866c344 07b6ee49 f6f31798 0b87a38b 890f70e2 c28cc1d5
fd1b4e80 7fa25483 09e79459 6bf92155 c55240b4 93eeb4eb af3f8aec 8906ef48
140c57bb 5ca4471f 275c1932 7e90976f f0dfe8a3 04a7861f cce7a320 7267df2e
61f9b6b8 22bb70ac d9cedb73 3cf9747b c2636892 48b35385 a94bfae5 fd020301
0001300d 06092a86 4886f70d 01010505 00038181 003c7e16 be4aff40 8fe69a31
acf31808 680e44eb 8ede9094 f9a4a147 0ae18cdc 000dc07f c1da1af4 a2d964ed
288689ee 95179ad0 90728324 9803248d b9d10641 01897453 fe7fafcd 34dee13a
92798615 4acb1f27 14fdb346 ab3eb825 04f23791 81d08fa2 b54c6a47 aedd9694
1c9fbcb4 455fd5ce 420298aa 9333737c 19f0e715 50
quit
crypto isakmp identity address
crypto isakmp nat-traversal 30
crypto ikev2 policy 1
<--- More --->
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
<--- More --->
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev2 remote-access trustpoint ASDM_TrustPoint0
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
<--- More --->
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
<--- More --->
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
<--- More --->
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
<--- More --->
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
management-access inside
dhcpd dns 10.2.11.121 10.2.11.138
dhcpd lease 36000
dhcpd ping_timeout 30
dhcpd domain sub.domain.net
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl trust-point ASDM_TrustPoint0 outside
webvpn
<--- More --->
anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
anyconnect profiles VPN_client_profile disk0:/VPN_client_profile.xml
anyconnect enable
tunnel-group-list enable
group-policy domain internal
group-policy domain attributes
banner value You are attempting to access secured systems at thsi facility. All activity is monitored and recorded. Disconnect now if you are not authorized to access these systems or do not possess valid logon credentials.
wins-server value 10.2.11.121 10.2.11.138
dns-server value 10.2.11.121 10.2.11.138
vpn-idle-timeout none
vpn-filter value vpn_access_in
vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value domain_splitTunnelAcl
default-domain value sub.domain.net
split-dns value sub.domain.net
group-policy DfltGrpPolicy attributes
dns-server value 10.2.11.121 10.2.11.138
vpn-filter value outside_access_in
vpn-tunnel-protocol l2tp-ipsec
default-domain value sub.domain.net
split-dns value sub.domain.net
address-pools value VPNUsers
username **** password **** encrypted privilege 15
<--- More --->
username **** password **** encrypted privilege 15
username **** attributes
webvpn
anyconnect keep-installer installed
anyconnect dtls compression lzs
anyconnect ssl dtls enable
anyconnect profiles value VPN_client_profile type user
tunnel-group DefaultL2LGroup general-attributes
default-group-policy domain
tunnel-group DefaultRAGroup general-attributes
address-pool VPNUsers
authentication-server-group ActiveDirectory
default-group-policy domain
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
ikev1 trust-point ASDM_TrustPoint0
tunnel-group DefaultWEBVPNGroup general-attributes
default-group-policy domain
tunnel-group domain type remote-access
tunnel-group domain general-attributes
address-pool (inside) VPNUsers
address-pool VPNUsers
authentication-server-group ActiveDirectory LOCAL
authentication-server-group (inside) ActiveDirectory LOCAL
<--- More --->
default-group-policy domain
dhcp-server link-selection 10.2.11.121
tunnel-group domain ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
<--- More --->
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly 21
subscribe-to-alert-group configuration periodic monthly 21
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:2578e19418cb5c61eaf15e9e2e5338a0
: endHello,
I've been working on this issue for a few days with no success. We're setting up a new Cisco ASA 5515 in our environment and are trying to get a simple IPSec VPN setup on it for remote access. After some initial problems, we've gotten it to where the VPN tunnel authenticates the user and connects as it should, however we cannot ping into our LAN. We are able to ping as far as the firewall's inside interface. I've tried other types of traffic too and nothing gets through. I've checked the routes listed on the VPN client while we're connected and they look correct - the client also shows both sent and received bytes when we connect using TCP port 10000, but no Received bytes when we connect using UDP 4500. We are trying to do split tunneling, and that seems to be setup correctly because I can still surf while the VPN is connected.
Below is our running config. Please excuse any messyness in the config as there are a couple of us working on it and we've been trying a whole bunch of different settings throughout the troubleshooting process. I will also note that we're using ASDM as our primary method of configuring the unit, so any suggestions that could be made with that in mind would be most helpful. Thanks!
ASA-01# sh run
: Saved
ASA Version 8.6(1)2
hostname ASA-01
domain-name domain.org
enable password **** encrypted
passwd **** encrypted
names
interface GigabitEthernet0/0
speed 100
duplex full
nameif inside
security-level 100
ip address 10.2.0.1 255.255.0.0
interface GigabitEthernet0/1
description Primary WAN Interface
nameif outside
security-level 0
ip address 76.232.211.169 255.255.255.192
interface GigabitEthernet0/2
shutdown
<--- More --->
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
shutdown
no nameif
no security-level
no ip address
interface Management0/0
speed 100
<--- More --->
duplex full
shutdown
nameif management
security-level 100
ip address 10.4.0.1 255.255.0.0
ftp mode passive
clock timezone MST -7
clock summer-time MDT recurring
dns domain-lookup inside
dns server-group DefaultDNS
name-server 10.2.11.6
domain-name domain.org
dns server-group sub
name-server 10.2.11.121
name-server 10.2.11.138
domain-name sub.domain.net
same-security-traffic permit intra-interface
object network 76.232.211.132
host 76.232.211.132
object network 10.2.11.138
host 10.2.11.138
object network 10.2.11.11
host 10.2.11.11
<--- More --->
object service DB91955443
service tcp destination eq 55443
object service 113309
service tcp destination range 3309 8088
object service 11443
service tcp destination eq https
object service 1160001
service tcp destination range 60001 60008
object network LAN
subnet 10.2.0.0 255.255.0.0
object network WAN_PAT
host 76.232.211.170
object network Test
host 76.232.211.169
description test
object network NETWORK_OBJ_10.2.0.0_16
subnet 10.2.0.0 255.255.0.0
object network NETWORK_OBJ_10.2.250.0_24
subnet 10.2.250.0 255.255.255.0
object network VPN_In
subnet 10.3.0.0 255.255.0.0
description VPN User Network
object-group service 11
service-object object 113309
<--- More --->
service-object object 11443
service-object object 1160001
object-group service IPSEC_VPN udp
port-object eq 4500
port-object eq isakmp
access-list outside_access_in extended permit icmp object VPN_In 10.2.0.0 255.255.0.0 traceroute log disable
access-list outside_access_in extended permit object-group 11 object 76.232.211.132 interface outside
access-list outside_access_in extended permit object DB91955443 any interface outside
access-list outside_access_in extended permit udp any object Test object-group IPSEC_VPN inactive
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended deny ip any any
access-list inside_access_in extended permit ip any any log disable
access-list inside_access_in extended permit icmp any any echo-reply log disable
access-list inside_access_in extended permit ip object VPN_In 10.2.0.0 255.255.0.0 log disable
access-list domain_splitTunnelAcl standard permit 10.2.0.0 255.255.0.0
access-list domain_splitTunnelAcl standard permit 10.3.0.0 255.255.0.0
access-list vpn_access_in extended permit ip any any
pager lines 24
logging enable
logging asdm informational
mtu management 1500
mtu inside 1500
mtu outside 1500
ip local pool VPNUsers 10.3.0.1-10.3.0.254 mask 255.255.0.0
<--- More --->
no failover
icmp unreachable rate-limit 1 burst-size 1
icmp permit any management
icmp permit any inside
icmp permit any outside
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic any interface
nat (inside,outside) source dynamic any WAN_PAT inactive
nat (outside,outside) source static 76.232.211.132 76.232.211.132 destination static interface 10.2.11.11 service 113309 113309
nat (outside,outside) source static 76.232.211.132 76.232.211.132 destination static interface 10.2.11.11 service 11443 11443
nat (outside,outside) source static 76.232.211.132 76.232.211.132 destination static interface 10.2.11.11 service 1160001 1160001
nat (outside,outside) source static any any destination static interface 10.2.11.138 service DB91955443 DB91955443
nat (inside,outside) source static NETWORK_OBJ_10.2.0.0_16 NETWORK_OBJ_10.2.0.0_16 destination static NETWORK_OBJ_10.2.250.0_24 NETWORK_OBJ_10.2.250.0_24 no-proxy-arp route-lookup
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 76.232.211.129 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
<--- More --->
dynamic-access-policy-record DfltAccessPolicy
aaa-server ActiveDirectory protocol nt
aaa-server ActiveDirectory (inside) host 10.2.11.121
nt-auth-domain-controller sub.domain.net
aaa-server ActiveDirectory (inside) host 10.2.11.138
nt-auth-domain-controller sub.domain.net
user-identity default-domain LOCAL
eou allow none
http server enable
http 10.4.0.0 255.255.255.0 management
http 10.2.0.0 255.255.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
no sysopt connection permit-vpn
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
<--- More --->
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto ca trustpoint ASDM_TrustPoint0
enrollment self
<--- More --->
subject-name CN=ASA-01
crl configure
crypto ca certificate chain ASDM_TrustPoint0
certificate a6c98751
308201f1 3082015a a0030201 020204a6 c9875130 0d06092a 864886f7 0d010105
0500303d 31153013 06035504 03130c43 5248442d 4d432d46 57303131 24302206
092a8648 86f70d01 09021615 43524844 2d4d432d 46573031 2e637268 642e6f72
67301e17 0d313330 35303730 32353232 325a170d 32333035 30353032 35323232
5a303d31 15301306 03550403 130c4352 48442d4d 432d4657 30313124 30220609
2a864886 f70d0109 02161543 5248442d 4d432d46 5730312e 63726864 2e6f7267
30819f30 0d06092a 864886f7 0d010101 05000381 8d003081 89028181 00c23d5f
acbf2b3f 9fe6e3c9 1866c344 07b6ee49 f6f31798 0b87a38b 890f70e2 c28cc1d5
fd1b4e80 7fa25483 09e79459 6bf92155 c55240b4 93eeb4eb af3f8aec 8906ef48
140c57bb 5ca4471f 275c1932 7e90976f f0dfe8a3 04a7861f cce7a320 7267df2e
61f9b6b8 22bb70ac d9cedb73 3cf9747b c2636892 48b35385 a94bfae5 fd020301
0001300d 06092a86 4886f70d 01010505 00038181 003c7e16 be4aff40 8fe69a31
acf31808 680e44eb 8ede9094 f9a4a147 0ae18cdc 000dc07f c1da1af4 a2d964ed
288689ee 95179ad0 90728324 9803248d b9d10641 01897453 fe7fafcd 34dee13a
92798615 4acb1f27 14fdb346 ab3eb825 04f23791 81d08fa2 b54c6a47 aedd9694
1c9fbcb4 455fd5ce 420298aa 9333737c 19f0e715 50
quit
crypto isakmp identity address
crypto isakmp nat-traversal 30
crypto ikev2 policy 1
<--- More --->
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
<--- More --->
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev2 remote-access trustpoint ASDM_TrustPoint0
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
<--- More --->
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
<--- More --->
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
<--- More --->
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
<--- More --->
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
management-access inside
dhcpd dns 10.2.11.121 10.2.11.138
dhcpd lease 36000
dhcpd ping_timeout 30
dhcpd domain sub.domain.net
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl trust-point ASDM_TrustPoint0 outside
webvpn
<--- More --->
anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
anyconnect profiles VPN_client_profile disk0:/VPN_client_profile.xml
anyconnect enable
tunnel-group-list enable
group-policy domain internal
group-policy domain attributes
banner value You are attempting to access secured systems at thsi facility. All activity is monitored and recorded. Disconnect now if you are not authorized to access these systems or do not possess valid logon credentials.
wins-server value 10.2.11.121 10.2.11.138
dns-server value 10.2.11.121 10.2.11.138
vpn-idle-timeout none
vpn-filter value vpn_access_in
vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value domain_splitTunnelAcl
default-domain value sub.domain.net
split-dns value sub.domain.net
group-policy DfltGrpPolicy attributes
dns-server value 10.2.11.121 10.2.11.138
vpn-filter value outside_access_in
vpn-tunnel-protocol l2tp-ipsec
default-domain value sub.domain.net
split-dns value sub.domain.net
address-pools value VPNUsers
username **** password **** encrypted privilege 15
<--- More --->
username **** password **** encrypted privilege 15
username **** attributes
webvpn
anyconnect keep-installer installed
anyconnect dtls compression lzs
anyconnect ssl dtls enable
anyconnect profiles value VPN_client_profile type user
tunnel-group DefaultL2LGroup general-attributes
default-group-policy domain
tunnel-group DefaultRAGroup general-attributes
address-pool VPNUsers
authentication-server-group ActiveDirectory
default-group-policy domain
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
ikev1 trust-point ASDM_TrustPoint0
tunnel-group DefaultWEBVPNGroup general-attributes
default-group-policy domain
tunnel-group domain type remote-access
tunnel-group domain general-attributes
address-pool (inside) VPNUsers
address-pool VPNUsers
authentication-server-group ActiveDirectory LOCAL
authentication-server-group (inside) ActiveDirectory LOCAL
<--- More --->
default-group-policy domain
dhcp-server link-selection 10.2.11.121
tunnel-group domain ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
<--- More --->
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly 21
subscribe-to-alert-group configuration periodic monthly 21
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:2578e19418cb5c61eaf15e9e2e5338a0
: end -
Cisco VPN client can't ping remote network.
I have recently installed a Cisco 5505 and have problems with some of the Cisco VPN Hosts I connect to using the Cisco VPN dialer. The Cisco Dialer connects fine but I am unable to connect to any computers on the remote network.
I have tracked the issue down to the ones that work & the ones that don't. If the remote Cisco is on the same sub-net as the computers I am connecting to it works fine. If the remote Cisco is on a differant sub-net then the computer I am trying to connect to it won't work unless I set up a static nat for a given pc on my network.
When I run through the dynamic Nat for my network I get the following error on the 5505.
regular translation creation failed for protocol 50 src inside:192.168.97.215 dst outside:xx.xxx.xx.xxx
I have been trying to find a solution to this issue ever since I installed the router and have not had any luck with any of the suggestions I have found on the Web. I have attached my config.
Any help would be appreciated.
MikeThanks for your response.
Yes that exactly the setup we are trying to get to work.
I have a call into them now and will check on their set up but I have no control over how they configure their routers I can only make requests.
I was hoping there was something causing it on my side as I deal with Hospitals and they can get very picky about their security.
I guess what is confusing me is it works if it goes through a Static Nat but not if it runs through our dynamic Nat.
Mike -
I can't see fvor dt.se the side which I can in Explorer.Other sides is perfect!
I can´t see the whole side in dt.se, which I can in Explorer. This happened when I got the new version of Firefox this week
Clear the cache and the cookies from sites that cause problems.
"Clear the Cache":
* Tools > Options > Advanced > Network > Offline Storage (Cache): "Clear Now"
"Remove Cookies" from sites causing problems:
* Tools > Options > Privacy > Cookies: "Show Cookies"
Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
*Don't make any changes on the Safe mode start window.
*https://support.mozilla.com/kb/Safe+Mode
*https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes -
ASA configuration is below!
ASA Version 9.1(1)
hostname ASA
domain-name xxx.xx
names
ip local pool VPN_CLIENT_POOL 192.168.12.1-192.168.12.254 mask 255.255.255.0
interface GigabitEthernet0/0
nameif inside
security-level 100
ip address 192.168.11.1 255.255.255.0
interface GigabitEthernet0/1
description Interface_to_VPN
nameif outside
security-level 0
ip address 111.222.333.444 255.255.255.240
interface GigabitEthernet0/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
shutdown
no nameif
no security-level
no ip address
interface Management0/0
management-only
nameif management
security-level 100
ip address 192.168.5.1 255.255.255.0
ftp mode passive
dns server-group DefaultDNS
domain-name www.ww
same-security-traffic permit intra-interface
object network LAN
subnet 192.168.11.0 255.255.255.0
description LAN
object network SSLVPN_POOL
subnet 192.168.12.0 255.255.255.0
access-list VPN_CLIENT_ACL standard permit 192.168.11.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu management 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-711.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (outside,inside) source static SSLVPN_POOL SSLVPN_POOL destination static LAN LAN
route outside 0.0.0.0 0.0.0.0 111.222.333.443 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
webvpn
url-list none
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
aaa authentication http console LOCAL
aaa authorization exec LOCAL
http server enable
http 192.168.5.0 255.255.255.0 management
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpoint ASDM_TrustPoint5
enrollment terminal
email [email protected]
subject-name CN=ASA
ip-address 111.222.333.444
crl configure
crypto ca trustpoint ASDM_TrustPoint6
enrollment terminal
fqdn vpn.domain.com
email [email protected]
subject-name CN=vpn.domain.com
ip-address 111.222.333.444
keypair sslvpn
crl configure
crypto ca trustpool policy
crypto ca certificate chain ASDM_TrustPoint6
telnet timeout 5
ssh 192.168.11.0 255.255.255.0 inside
ssh timeout 30
console timeout 0
no ipv6-vpn-addr-assign aaa
no ipv6-vpn-addr-assign local
dhcpd address 192.168.5.2-192.168.5.254 management
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl trust-point ASDM_TrustPoint6 outside
webvpn
enable outside
csd image disk0:/csd_3.5.2008-k9.pkg
anyconnect image disk0:/anyconnect-win-3.1.04066-k9.pkg 1
anyconnect enable
tunnel-group-list enable
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-clientless
group-policy VPN_CLIENT_POLICY internal
group-policy VPN_CLIENT_POLICY attributes
wins-server none
dns-server value 192.168.11.198
vpn-simultaneous-logins 5
vpn-session-timeout 480
vpn-tunnel-protocol ssl-client
split-tunnel-policy tunnelspecified
split-tunnel-network-list value VPN_CLIENT_ACL
default-domain value mycomp.local
address-pools value VPN_CLIENT_POOL
webvpn
anyconnect ssl dtls enable
anyconnect keep-installer installed
anyconnect ssl keepalive 20
anyconnect ssl rekey time 30
anyconnect ssl rekey method ssl
anyconnect dpd-interval client 30
anyconnect dpd-interval gateway 30
anyconnect dtls compression lzs
anyconnect modules value vpngina
customization value DfltCustomization
group-policy IT_POLICY internal
group-policy IT_POLICY attributes
wins-server none
dns-server value 192.168.11.198
vpn-simultaneous-logins 3
vpn-session-timeout 120
vpn-tunnel-protocol ssl-client ssl-clientless
split-tunnel-policy tunnelspecified
split-tunnel-network-list value VPN_CLIENT_ACL
default-domain value company.com
address-pools value VPN_CLIENT_POOL
webvpn
anyconnect ssl dtls enable
anyconnect keep-installer installed
anyconnect ssl keepalive 20
anyconnect dtls compression lzs
customization value DfltCustomization
username vpnuser password PA$$WORD encrypted
username vpnuser attributes
vpn-group-policy VPN_CLIENT_POLICY
service-type remote-access
username vpnuser2 password PA$$W encrypted
username vpnuser2 attributes
service-type remote-access
username admin password ADMINPA$$ encrypted privilege 15
tunnel-group VPN type remote-access
tunnel-group VPN general-attributes
address-pool VPN_CLIENT_POOL
default-group-policy VPN_CLIENT_POLICY
tunnel-group VPN webvpn-attributes
authentication aaa certificate
group-alias VPN_to_R enable
tunnel-group IT_PROFILE type remote-access
tunnel-group IT_PROFILE general-attributes
address-pool VPN_CLIENT_POOL
default-group-policy IT_POLICY
tunnel-group IT_PROFILE webvpn-attributes
authentication aaa certificate
group-alias IT enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
: endHi,
here's what you need:
same-security-traffic permit intra-interface
access-list VPN_CLIENT_ACL standard permit 192.168.12.0 255.255.255.0
nat (outside,outside) source static SSLVPN_POOL SSLVPN_POOL destination static SSLVPN_POOL SSLVPN_POOL
Patrick
Maybe you are looking for
-
Hi I have launched swing application in webstart. I have used some gif file in my application. While creating Jar file I have added all the gif files also. But I couln't view that gif files while running the application on the webstart. Thanks in adv
-
Exchange 2010, Outlook 2013. My CEO's assistant was always able to SEND AS him as his account loads in her Outlook Profile. She would go to his Inbox and start a new email and change the FROM to him and send as him. Last week out of nowhere when s
-
Hi, We have an issue where the data in the source system has values 0 and for some its blank. When it is extracting the data into BI, at PSA level, its treating blanks as zeroes and storing as value 0, where there is no differentiation between these
-
Installed Photoshop CS5 but it appears camera raw DID NOT install in Bridge
It appears Camera Raw didn't install in CS5 Bridge as all ACR functions in bridge are greyed out. I've been on hold for Adobe Support for over 2.5 hours over two days and after trying to use their "we'll call you back feature" which just rang for 18
-
Can we generate two invoice for same product in two different currency
dear all gurus, actually we are in export sales so we are generating export invoice. my client is asking for another invoice in INR too this is called comercila invoice with this i ve to generate the ARE form so how to do this three things 1.export i