E 72 gps mute?

Hi,
I have a e72 nokia running gps with no sound.. no words. Volumen is full but no sound....
What can I do?
regards

heze54 wrote:
perfect... but how to install this software?
Hi heze54
You need Nokia Multimedia Transfer installed from here: http://www.nokiausa.com/get-support-and-software/software/nokia-multimedia-transfer/download and you might need an iSync Plug-in for your E72 from here: http://www.nokiausa.com/get-support-and-software/software/isync/compatibility-and-download
Happy to have helped forum in a small way with a Support Ratio = 37.0

Similar Messages

How can I use the embeded GPS in my Sprint MiFi Hotspot for my location on my iPad4 wifi only device

The iPad uses the wifi network to determine the location My default connection is through my Sprint MiFi, but it does not use its location gps eventhough it is active for Maps. It did use a local tower in a wisconsin town yesterday and no it thinks I'm there and I cannot refresh it. I am brand new to apple IOS as I won the device last Thursday. I'm trying to upgrade the OS to 7 as it has 6 installed. I need to find a faster connection to do it though.
Any help wpuld be appreciated

Re: How can I get the best out of my battery life?
Hi,
When I make phone calls people on the other end have difficulty hearing me. They describe as they can hardly hear me as if I was speaking through the pillow etc). I am not touching any buttons and obviously it is not mute. This was happening couple of time in June, then every now and then. Recently it happened a few time in 2 weeks. I was trying to check if it was a reception issue but the place I spoke from is my office I make 70% of phone calls from. Can you book time for me in repair shop and address the issue.
Thank you.
Sergey Sinitsyn

5800 XM : speaker mutes when connected to my car k...

Hello,
I have a 5800 XM with the last software version (v31).
My car is a Ford Cmax from november 2007 and the built-in car kit is made by ... nokia.
The car kit works fine : contacts are found, call i/out list is ok and phones calls works perfectly.
But when the phone connects to the car kit, the phone speaker mutes but sounds (other than phone calls) are not played through the car speakers, which means for instance that I can not ear gps navigation instructions.Then if I plug a headset, I can ear gps through the headset ...
Any idea to fix this ?

Same problem here.
Nokia C6-00
Mondeo Bluetooth carkit
Phone works perfectly. However, every sound is transferred to the radio. But the radio is muting these sounds. While a phone call, I can hear the navigation from the radio-speakers ...
So ... Workaround: keep calling while you need the navigation ... or ... Nokia, pls help! ;-)
I couldn't find an option to disable the sound transfer - nor could I find an option to disable the sound muting within the radio ...
Anybody got an idea?

Sony GPS in Aperture 3

Does anyone here know if the GPS data generated by a Sony SLT-A55 is recognized properly by Aperture?

The STL-A55 manual [here|http://www.docs.sony.com/release/SLTA33.pdf] - caution, big download - is mute on whether the standard EXIF lat/long metadata fields are being used, though they do mention using their own PMB (?) program to do mapping and other geolocating functions.
But it's hard to imagine they'd eff-up so badly as to invent a completely proprietary solution for embedding GPS data. Actually, come to think of it, perhaps DPReview has covered this...
[The GPS is new on the Alpha A55. The function can be activated in the menu and if satellites are found and the camera is positioned geo-data is written in to the images EXIF-data and displayed with the image in review mode.|http://www.dpreview.com/reviews/sonyslta55/page5.asp]
I'd say you could probably trust DPReview, so if that's the case then SLT-AFF images should geolocate automatically in Aperture's Places.
-Steve

Nokia N95 GPS - 616 Car Kits

When i use the GPS on my N95 - if it connnectd to the car kit the voice navigation does not come on - i have to diconnect from the kit to use GPS properly. If i use the remote sim option it mute the radio at all times until i close the nagivation application. Any suggestions

Looks to be a problem with a lot of car kits... many don't do the bluetooth audio thing - tho they do phone calls fine (different profiles I guess...)
So when you pair the phone to the car you loose the Nav voice because the phone is trying to pass all things audio over the bluetooth link - even if the car doesn't know what to do with it..
Leaving you in the position where calls work fine but voice nav is lost...
It'd be nice if we could leave the nav using the phone speakers and the calls using the bluetooth car kit... it might be a bit of a compromise but at least it would keep us legal whilst driving and still allow the use of the maps.. after all where better to use a nav app than in a car???
Pity Nokia seemed to have missed this one....

Problem with GPS in my 5800

I have proble with GPS , After update my phone this service was working and I do some change in internet setting in my phone becase it was log to net with auto way so I change the access point to wrong number to disconnect to net with auto way
after this change the GPS work one time and didnt work after that .
--Dose this service need net to work ?
-- If no how i get it work again ?
PLZ I need this service in my phone so much becase sometime I drive my car in new places and I use it very hard
PLZ help my

Go to Maps-->Spanner Icon-->Internet-->Connection...set to OFFLINE
Also.. Menu-->Applications-->Location-->Positioning-->Positioning Methods.. select ONLY integrated GPS
BTW to prevent auto connection to Internet..
Menu-->Settings-->connectivity-->Admin Settings-->Packet Data-->Packat Data connection...set to When Needed
..and also..
Menu-->Settings-->Connectivity-->Destinations-->Internet.. select the Access Point-->Use Acces Point (At extreme bottom).. set to After Confirmation..

Error while downloading. message on E71 GPS USA Ma...

“Error while downloading” message on E71 with updated GPS USA Maps
I’m sure I’m not the only one having this problem but I recently updated my maps on my Straight Talk Nokia E71. The phone says I have map download V 3.03 10wk bo4 Mw Open GL LM MN, Map version 0.1.25.114.and I’m using Nokia Ovi Suite 2.2.1.23. After I installed V3.03, I installed it and download the 1.46GB USA map file and the three turn by turn files. But when I first started the GPS app I started getting the following error “Error while downloading”(This is on phone only)
I have tried to factory reset the phone, re-format the 8GB memory card, remove City data and GF files and even unloaded OVI Suite and reload it. But every time I select GPS app and start to find places or my position, I get "Error while downloading" message. I’m new to this phone and didn’t get a respectable book from Straight Talk. So I don’t know much about this phone or Nokia OS. What is this error and how do I fix it. Also when I try to sync from the phone I get the response "system error". Ovi suite on the PC says I have downloaded all the USA maps and English voice with street names. Please help I’m at a lost.
Computer specs
I am running Win-Vista, with a Broadband connection. 3 GB Ram, 2 gig Pentium dual core.
Tran’s flash card has plenty room left on card over 5 gigs left.
If I need to delete a file on the phone please tell me the exact file name because I’m not sure which one to remove from the apps folder.
Solved!
Go to Solution.

@Action_Jackson
Welcome to the forum!
Whilst easy for me to say as keep very little data on device, I would suggest backup essential data then delete E:\cities + ,qf file followed by resetting device to "Out of box" state by keying in #7370# then 12345 (default Nokia lock code unless altered by yourself). At this point you would need to open OVI Maps application on device to re-initialise application and re-define necessary folder structure on memory card for device to be recognised by OVI Suite > Maps to re-download your regional mapping.
Happy to have helped forum with a Support Ratio = 42.5

Network based and a-gps, data use tests

i was trying to find this kind of info, but only found others asking.
i hope this is useful info for others, especially while roaming.
skip to the bottom for conclusion,
this is the process i took:
i called nokia tech support,
their phone support his horrible,
the people on the phone don't actually know anything, and have to look up everything you ask them.
they were the worst.
i emailed nokia tech support.
my message was:
"i would like to know the difference between assisted gps positioning, and network based positioning. these are 2 of the 4 options on my nokia e66 for positioning methods. i would like to know if network based positioning uses internet data from my service provider to obtain my gps position. i am especially concerned with this function while i'm roaming internationally, as i do not want to be charged for roaming data use."
in about half hour they responded w/ an answer, and then 45 min after that someone else responded w/ an answer.
the first response, minus the hello's etc. was:
"In response to your email, Assisted GPS and Network Based positioning methods generate costs related to data traffic so you will be charged for data use. Only "normal" GPS and Bluetooth GPS do not generate additional costs related to data traffic.
Normal GPS is quite slow and does not work indoors. Therefore, it is recommended to enable at least A-GPS to get a faster position outdoors.
Network based and Wi-Fi positioning also allow you to update your position inside buildings, but they cannot be used for navigation."
the 2nd response was:
"In response to your inquiry, the difference between Assisted GPS positioning (A-GPS) and Network based positioning is that, A-GPS uses satellites while Network based positioning is based on information of your cellular network environment. It allows you to update your position inside buildings, but they cannot be used for navigation. Both positioning methods generate costs related to data traffic (unless you have configured the device to use Wi-Fi connection to make the internet connection). The cost may vary while you are on roaming. Kindly contact the service provider for information about data transmission costs."
i can also respond w/ more questions, but instead did some tests, starting with sitting home, indoors, and eventualy moving to a window w/ lots of sky.
test 1:
i enabled:
integrated gps
network based
assisted gps
opened maps,
set maps to be offline,
set default internet access point to my home wlan network,
closed maps,
cleared all counters and the log on the phone's communication log.
opened maps
there is a pink circle around the area i may be in,
the icon that would show gps satellite strength, changes to show the cell phone antenna icon.
but the packet data counter is sending/receiving a total of around 3-8kb immediately, and over the course of time, it keeps adding up, every 1-2 minutes, and it is shown as packet data to/from the access point "at&t internet"
over the course of ten minutes, it's been about 43kb.
and i can tell on the phone's home screen that the packet data connection becomes active when it does.
the maps kb indicator still says 0.0kb, with a line through the double arrow packet data symbol.
test 2:
now i exited maps,
cleared the counters and logs
i turned off a-gps.
enabled only integrated gps and network based.
i open maps,
the same thing is happening as with the assisted gps on, except i connected to my home wlan once, in the middle of connecting to at&t internet 10 or so times.
everything else is happening the same.
test 3:
i exited maps,
cleared the counters and logs.
enabled only integrated gps.
i open maps, and there is no evidence of packet data connection, or wlan connection.
nothing is showing up in the logs or packet counters, and there is no pink circle around where i may be.
if i set maps to go online, w/ my wlan as the access point, or at&t internet, their respective icons show up on maps, as well as the phone's home screen.
the phone's log show respective connections are made but w/ 0.0kb, and the phone's packet counter, as well as the maps kb usage, say 0.0kb.
test 4:
set maps to offline, w/ my wlan as access point.
exited maps,
turned phone off for a bit to test gps from cold start.
turned on phone,
cleared counters/logs,
enabled only assisted gps and integrated gps.
open maps, there's no pink circle around where i may be, just the red dot of where it thought i last was.
there's about 4-5kb of data transfer,
then i bring the phone to the window where there's a lot of clear sky, and my location is found pretty fast.
i know that w/o assisted gps, w/ only integrated gps, it takes a while to get the gps signals.
i went back and forth to/from the window, and there was packet data use again only once more, not continuously like w/ network based positioning.
so to conclude my tests,
setting the maps to be offline, still uses a-gps and network based positioning.
network based uses a more data, continuously,
which is the opposite of what i thought, i thought a-gps would use more, so i was using network based on and a-gps off while in canada. whoops.
using assisted gps uses about 5-10kb, which, when roaming, according to at&t, they charge 1.95cents/kb.
might be worthwhile for getting a quick gps signal, nothing worse than waiting forever for it to connect.
the only way to be completely clear of data use is disable network based and assisted gps, or set the phone to offline mode.

A-GPS: This uses information from cell network to get a rough idea of where you are. It then uses this information to figure out which satellites to look for. Result is a faster satellite lock. So A-GPS uses a few kB of data to get an initial position, but navigation is done using GPS satellites, which does not require ANY data connection.
Network based: This uses information from the cell network to plot the current position when GPS satellite signal is not available, ie indoors, in a tunnel, etc. Position info derived from the cell network is not as accurate as that from GPS satellites, but serves as a stopgap until GPS signal can be re-acquired. Network based positioning used your data connection EACH TIME the satellite lock is lost. So the amount of data used is dependent on the quality of access you have to the GPS satellites. If you don't lose the connection to the GPS satellites, then you won't use any data.
The ‘offline’ option within the Nokia Maps app only refers to street, POI, etc searches, NOT to A-GPS, Network based positioning or to connecting with the GPS satellites.
If you want to navigate without using ANY data connection, set A-GPS off AND set Network based positioning off AND set the Internet option in Nokia Maps to Offline. Do this and you will not use any of your data connection allowance when navigating. There is no need to put the phone into flight mode.
If I've helped you, you can thank me by clicking the green 'kudos' star on my post. Cheers.

Error (MUT-02041) during Installation of Enterprise Portal 6.0

Hi,
I have got a serious problem during the installation of SAP EP 6.0.
Background Information:
I succesfully installed Netweaver '04 Web AS Java 6.40 system. Operating System is Red Hat Enterprise Linux 3. SAP Database is MaxDB 7.50.
Problem Description:
During step 2 (Deploy JDBC Libraries) of the portal installation process the installation routine stops with error code MUT - 02041.
Complete Error Message:
MUT-02041 SDM call of deploySdaList ends with returncode 4. See output of logfile /tmp/sapinst_instdir/NW04SR1/EP/EP/callSdmViaSapist.log.
Output of Logfile:
Error: Aborted: development component 'com.sapportal.datadirect'/'sap.com'/'SAP AG'/'609.20041012102246.0000':
Caught exception while checking the login credentials for SAP J2EE Engine. Check whether the SAP J2EE Engine is up and running.
com.sap.engine.deploy.manager.DeployManagerException: Error: Cannot connect to HOST: [CG-DEV-SERVER] with user name: [Administrator]
Check your login information.
Exception is: com.sap.engine.services.jndi.persistent.exception.NamingException: Exception while trying to get InitialContext. [Root exception is com.sap.engine.services.security.exceptions.BaseLoginException: User not authorized.]
Error: -
At least one of the Deployments failed -
What I tried do solve the problem:
I used the Visual Administrator tool to check the user "Administrator". (I used the user "Administrator" to connect to the J2EE Engine - localhost, port 50004).
Administrator is not locked, is member of group Administrators, member of group Authenticed Users, member of group Everyone, is valid until year 2500 and has 80 succesful logon counts.
The user looks fine to me. I do not know what else I could check to solve the problem. Anything I forgot to check? I am grateful for any kind of help (pointer to docs, advise, step by step solution).
Cheers Martin
Message was edited by: Martin Kellermann

Hi,
here an uodate of the progress I am making to solve the problem described above.
Due to the output of the logfile (User not authorized), I think the "Administration" user does not have enough rights to perform the required actions needed for the installation.
Well, I looked it up (Visual Administrator --> Cluster --> Server 0 ... --> Services --> Security Provider -->Runtime --> Policy Configurations --> "service.naming" in "Components" List --> Security Roles).
According to http://help.sap.com/saphelp_webas630/helpdata/en/de/83343ecc7f892ee10000000a114084/frameset.htm, all users and groups that are granted permission "jndi_all_operations" can perform all operations available in the naming system.
I checked and found out that jndi_all_operations is merely a role reference to security role "administrators". Group "Administrators" is assigend to security role "administrator". As I mention before, user "Administrator" is member of group "Administrators". I think user "Administrator" has been granted all required permissions.
Am I wrong, what else could cause such an error message! Need some guideance.
Martin

IPhone 6 location services/gps not working

Anyone else have an issue with iPhone 6 location services/gps not working? I have had it happen to me twice where it stopped working for good 7 or 8 hours and then all of sudden it starts working again. For example, directions don't work, every time I open Apple Maps it will say "Cannot determine location", then when I press the location icon on the bottom left, it will try to search again and have an approximate location but not exact, where as the iPad that I have right next to it is able to pin point the exact location. Sometimes the location circle is pulsing blue sometimes its gray. If I am driving and have tracking on it won't track, and so on. I have tried to setup the phone as new without restoring the backup, when it stopped working with no luck, it still didn't work. I went and restore it back from backup and few hours later it started to work again. This has happened twice now since I got the phone last Friday.

Check your "Privacy" settings on your iPhone see what apps are using your location.

Audio mute button

Sup guys, just now the mute button on my keyboard doesnt want to get off mute, Ive pressed it and nothing, it stays mute and tried pressing the button to raise the volume and stays mute. Using Hp assistant i have this error IDT HIgh Definition Audio CODEC Error(52) Version 6.10.6395.0. I have a hp envy 4 ultrabook 1015dx...any help?
This question was solved.
View Solution.

Hi,
Try the following.
Download the IDT Audio installer on the link below and save it to your Downloads folder.
http://ftp.hp.com/pub/softpaq/sp56501-57000/sp56717.exe
When done, open windows Control Panel, open Device Manager and open up Sound, Video and Game Controllers. Right click the IDT device and select Uninstall - you should also get a prompt to remove the current driver, tick the box to allow this and then proceed with the uninstall.
When complete, restart the notebook and let Windows fully load. Open your Downloads folder, right click on the IDT installer and select 'Run as Administrator' to start the installation. When this has completed, restart the notebook again.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

GPS issue please help me please

Hi guys,
Well i know there are several forms for GPS issue but i cant find the right one for me...Please guys help me if u can.
I have N95 8 GB with GPS activated for Middle East Dubai....
Now the issue is this that before i was used to connect very quickly say about 10 minutes but right now i mean as of last couple of weeks its taking hell of time indeed not connecting at all...I place my mobile and my frnds mobile at same place but mine is not connecting at all...his mobile connects like in minute or so....please can u guys help me...my mobile is rarely used for 3 months...
Do i need to change some settings....If satellite is not available it sudnt connect to my frnds same mobile v20....but it connects to him not to mine....

First thing you do is to run GPS Data in connectivity and see if the phone achieves GPS lock any faster than now.
Secondly, run Nokia Maps, Goto Options>About and tell us the version you have. It should be accross the top of the screen.
Message Edited by cjlim on 10-Oct-2008 10:46 AM

Problems with applications: GPS Info QT - IM for N...

Problems with GPS Info QT: new update v1.25 (cancelled by Nokia recently) has a gap with the coordinates in longitude because the error is 1 degree 56 minutes more or less (big problem). But it is an excellent applications: when can we obtain it again?
Problems with IM for Nokia: it has been impossible to install the updade of this application. I have installed it several times and uninstall again, but I always see the word "error".
What happens with the Ovi Maps? before I could see the satellite maps in old version (like a google earth) but when Nokia updated to version 00.02.43.117 I cannot see it. (Maybe it had errors with the Nokia Maps.
Solved!
Go to Solution.

ilema wrote:
What happens with the Ovi Maps? before I could see the satellite maps in old version (like a google earth) but when Nokia updated to version 00.02.43.117 I cannot see it. (Maybe it had errors with the Nokia Maps.
Only for larger conurbations however:
Happy to have helped forum with a Support Ratio = 42.5

How do I use my iPhone 4s to set GPS co-ordinates to use at a later date?

I'm wanting to go to an aread in the bush - enter the GPS co-ordinates in my iPhone 4s and then be able to go back to the same place at a later date. How do I go about it. I have no idea if I even have a GPS on my iPhone 4s.

There is a built in GPS and map function that provides basic navigation using Google Maps. It's hard to miss right there on the home screen. However, it is maunal; you have to tap "next" when you reach each waypoint, and it does not provide spoken directions. It also downloads maps in real time, so it can be slow if you have a slow data connection, and it uses a lot of data if you are on a limited data plan. It is excellent for walking and public transportation, less useful in a vehicle unless you have a navigator sitting in the car.
There are several commercial GPS apps that you can buy from the App Store, but no free ones. Just search the App Store for "GPS".

How do I use GPS when out of range of cell towers, wifi, and bluetooth?

Recently, I encountered the following problem using my RAZR MAXX as an offline GPS device. I was in the Colorado back country trying to track my path with downloaded Topo maps, and found that the GPS was not responding to my app. When I looked at the app's satellite tracker screen, it showed some satellites, but no fixes. After some fumbling around, I found that, when I enabled cell tower communication by disabling Airplane mode, many more satellites showed up. After a moment, fixes showed up, and the app was able to locate me and track my path. This was IN SPITE OF the fact that the Droid never found a cell tower!
I also found that I had to keep the Droid out of Airplane mode, searching for service, in order for the GPS app to continue tracking. Any time that I put it in Airplane mode to disable service searching, the app's ability to detect satellites slowly degraded. After several seconds, it could no longer detect or fix on any satellites at all!! In order to restore the app's GPS tracking ability, I had to enable cell tower searching by disabling Airplane mode again.
Now, my question is, of course, is this the normal operation of a RAZR MAXX on Verizon? It would seem to me self-defeating to offer a functionality that only works when the Droid is draining the battery in attempts to contact non-existent cell towers. Is this truly the intended operation? Please tell me, so that I can either get my Droid fixed or pursue other ways of GPS tracking in back country. Thank you.
Model: DROID RAZR MAXX
Android version: 4.1.2
System version: 98.72.165.XT912.Verizon.en.US
Baseband version: CDMA_N_05.21.00R LTEDC_U_09.1D.00
Webtop version: wt-3.0.0
Kernel version: 3.08-g3617609 hudsoncm@ilclbld32 #1 SMP PREEMPT Thu Nov 21 14:19:19 CST 2013
Build number: 9.8.2O-72_VZW-16-5
Build date: Thu Nov 21 14:10:17 CST 2013
System updates says system is up to date.

NEVER MIND!!! The app I was using was BackCountry. May Need GPS Airtime! This app may need GPS Airtime to function properly on Droids. Please bundle GPS Airtime with the paid version of Backcountry. Had I but know this, I would not have posted on Verizon my question about Airplane mode and GPS functioning, and would have saved time on my recent trip to Colorado back country. As it was, I had to discover the Airplane mode/GPS relationship on my own. PS: App works great on my RAZR MAXX, now that I have GPS Airtime and doesn't work for sour apples without it.
HOWEVER, Verizon, what are you going to do to fix this? I'd still like to know that.

E 72 gps mute?

Similar Messages

Maybe you are looking for