E-MU 0204 for Vinyl Recording: Missing Sampling Rates Using Windows 7 Drivers?

Hi all,
Just so you know, the primary use for the E-MU 0204 is to convert the mounds of LPs I have into digital format (either 88.2 or 96 kHz sampling at 24 bit). Having said that, I'm going through a lot of growing pains with the E-MU 0204 unit I just purchased. The specs of my setup is as follows:
-Windows 7 Pro 64Bit 8GB ram
-Stanton T.92 USB (with internal preamp removed)
-Shure M97xE cartridge
-ART DJ PreII Phono Preamp.
As far as I can tell, the E-MU drivers are properly loaded onto the OS and in the Device Manager>Sound, and video game controllers, windows correctly identifies the unit as a "E-MU 0204 USB".
From the specifications of the unit here:
"Sample Rates: 44.1, 48, 88.2, 96, 176.4, 192kHz from internal crystal (no sample rate conversion)
Bit Depth: 24-bit I/O, 32-bit processing
USB Hi-Speed
- Full 24-bit resolution at all sample rates
- Stereo in, stereo out at all sample rates"
Yet, in the "Recording Devices" of my OS, I get only the following choices:
-2 channel, 16 bit, 88200 Hz (Studio Quality)
-2 channel, 16 bit, 96000 Hz (Studio Quality)
-2 channel, 16 bit, 176400 Hz (Studio Quality)
-2 channel, 16 bit, 192000 Hz (Studio Quality)
-2 channel, 24 bit, 44100 Hz (Studio Quality)
-2 channel, 24 bit, 48000 Hz (Studio Quality)
-2 channel, 24 bit, 96000 Hz (Studio Quality)
-2 channel, 24 bit, 192000 Hz (Studio Quality).
The 44.1 kHz/16 bit, 48 kHz/24 bit, 88.2 kHz/24 bit, and 176.4 kHz/24 bit modes seem to be missing.
My preferred choice for recording LPs is to use 96/24 for LP music that I know will not be burned onto CD, and 88.2/24 for LP music I know may be burned onto CD in the future at some point.
Am I missing something here? Please help!
I'm pretty new to this whole E-MU interface stuff, so I appreciate your patience in advance.
Thanks kindly,
Andrew

dgoh88 wrote:
okay just got home, turned the PC back on and now all the sounds are distorted again. Tried completely disabling wireless ports, still the same. About to throw in the towl already
There can be other high priority prcosses as well.
Keep trying with DPC Latency Tool ...
Also, you could try by
- turning off all visual effects of O/S (incl. Aero)
- turn off indexing service
- launch perfmon.msc / system monitoring tool to see which processes uses CPU/etc.
If you already uninstalled XP then why not install XP as well (dual boot system). Most audio interfaces works better on 32-bit XP compared to Vista/W7 & 64-bit systems.
jutapa

Similar Messages

Griffin iMic USB vs. ADS Tech Instant Music for Vinyl Recording

This is a repost, I posted in OSX accidentally. Sorry! Anyway, can anyone advise me, I am new at this... I just bought an Audio-Technica AT-PL120 Direct Drive Turntable (on its way to me) so I can transfer old LP's to my Macbook Pro for iPod and CD listening. It has a selectable internal stereo phono preamplifier and the ability to choose from phono or line-level output. Now, to get the sound INTO my Macbook pro, should I go with the Griffin iMic USB or the ADS Tech Instant Music for Vinyl Recording? Also, anyone heard of THIS device and do I even need it?
Griffin Turntable Connection Cable with Grounding:
http://ec2.images-amazon.com/images/P/B0007PL4BC.01-ADG953YR6NRBF.SS500_SCLZZZZZZZ_V60716819.jpg
Thanks for ANY advice!
Jody
Mac OS X (10.2.x)
Macbook Pro 17" Mac OS X (10.4.8)

I think you probably have everything you need except for appropriate audio recording software. For example, your MacBook Pro probably has an audio input jack that can be set to line level. If that is the case, then all you need is a cable from the turntable (set at line level) to the MacBook's audio in (plus the recording software).
However, a quick websearch on the ADS thingy found a review which should help you.
http://www.macnn.com/reviews/review.php?id=164
Based on that, the ADS thing may be worth it just in terms of making it easier for you, even if you don't, strictly speaking, need it. It appears to include recording software called CD Spin Doctor. I'm not too fond if CD Spin Doctor, but it will get get the job done. I like Amadeus for audio recording.
The review may also provide you with sufficient explanation on how to do the whole process.

How can I get the shutter count for my Canon 7D Mark II using Windows XP?

How can I get the shutter count for my Canon 7D Mark II using Windows XP? I've been looking lots of places and doing some file uploads, but I can't seem to find anything. I'm wary of downloading software I know nothing about. Any help is greatly appreciated.
Solved!
Go to Solution.

Nevermind, just, sort of answered my own question. Doesn't work on XP, but using a Win 7 'puter I was able to use Shutter Count, which now works w/ the 7D Mark II.

Some times firefox does not opens facebook and google pages and this does not happen for other sites. Iam Currently using windows xp and using 3.6.3 Firefox version.Please help.

Some times the fire fox does not open google and facebook pages but it does not happen for other sites. Iam currently using Windows xp and iam using Mozilla Fire fox 3.6.3 .Please help
== URL of affected sites ==
http://www.facebook.com,www.google.com

You can try a direct connection and select No Proxy in the connection settings.
You can find the connection settings in "Tools > Options > Advanced : Network : Connection"
Also do a malware check with a few malware scan programs.<br />
You need to use all programs because each detects different malware.<br />
Make sure that you update each program to get the latest version of the database before doing a scan.
* http://www.malwarebytes.org/mbam.php - Malwarebytes' Anti-Malware
* http://www.superantispyware.com/ - SuperAntispyware
* http://www.safer-networking.org/en/index.html - Spybot Search & Destroy
* http://www.lavasoft.com/products/ad_aware_free.php - Ad-Aware Free
* http://www.microsoft.com/windows/products/winfamily/defender/default.mspx - Windows Defender: Home Page
See also "Spyware on Windows": http://kb.mozillazine.org/Popups_not_blocked and [[Searches are redirected to another site]]

I have a Mac desktop OSX Version 10.7.4 upgraded to Lion to use iCloud. Now my Parallels Desktop 5 for Mac/Build 5.0.9376 using Windows 7 does not open. What upgrade of Parallels do I need to make this work?

I have a Mac desktop OSX Version 10.7.4 upgraded to Lion to use iCloud. Now my Parallels Desktop 5 for Mac/Build 5.0.9376 using Windows 7 does not open. What upgrade of Parallels do I need to make this work? Or what do I need to do at this point?

Thank you Shootist007. I appreciate it!

Crop & Straighten script for vinyl record labels

Hey guys i have thousands of circular vinyl record labels that i have taken photos for.
I have created an action for doing this but it keeps opening many chunks as separate files and never closes/saves them leading the program to run out of memory.
I am hoping that a script can be created to allow the processing of a folder where it automatically saves/closes the files to a new destination.
It would also be better if it can close without saving and chunks that are small which would save me having to delete them manually.
Thanks

Have a look at this thread, it may help.
http://forums.adobe.com/message/3430751

How to call webservice for each record in a table using ODI

Hi
I am new to ODI and Webservice. I want to invoke a scenario in ODI using web service. I hava a weblogic application server with axis 2 deployed.
But I want call webservice for each record in a table
For eg: "EMP" table have 50 records, for each record web service should invoke
Can any one help me on it.
Thanks,
phani
Edited by: user12774166 on Jun 6, 2010 11:16 PM

If your goal is "call" a web service, Jason's Straub's [flex-ws-api|https://flex-ws-api.samplecode.oracle.com/] is by far the best I've seen. You might want read more about it on [his blog|http://jastraub.blogspot.com/search?q=+flex_ws_api+].
Tyler Muth
http://tylermuth.wordpress.com
[Applied Oracle Security: Developing Secure Database and Middleware Environments|http://sn.im/aos.book]

Need sample code using windows BitBlt() function to display image in CVI

Hello all,
I need a sample code which uses windows BitBlt() function to display image in CVI
Thank you.
Bob.

Hello Bob -
I'm curious why you'd like to use BitBlt. What functionality does it offer that you've not seen in the CVI canvas control?
It's hard to say without knowing what transitions you're looking for, but the canvas is very capable of animating/transitioning. The place it can fall a little short is if you require access to the alpha channel for transparency.
I put together a short demo for you - maybe it will address some of what you're looking for. The important functions are CanvasStartBatchDraw, CanvasEndBatchDraw, and CanvasDrawBitmap. The animation/transition is driven by a simple UI timer.
Let me know if you have any questions -
NickB
National Instruments
Attachments:
CanvasAnimation.zip ‏10 KB

Can I acquire waveform at faster sampling rate using external clock?

I am trying to acquire waveform at a sampling rate of 1MHz. My 6036E card is maxed out at 200KHz. Is there a way to achieve a sampling rate of 1MHz using an external sample clock? Your PFI pin can take external clock as an AI sample clock, right?

Hi,
I remember I asked the similar question before in the NI forum, they reply me:
the max sample rate (scan/s/channel) cannot be greater than your board max sample rate, even you use external scan clcok. So the answer is no for your case.

How to fix Error 3194 or "This device isn't eligible for the requested build" in i5 using Windows

While updating my iphone 5 to ios7.0.4 an Error 3194 or "This device isn't eligible for the requested build" has occered so i can't restore my iphone am using my itunes in Windows 8. So what can i do to recover my iphone

Hello OmPRakash69,
Thank you for your question!
It sounds like you are trying to update the phone to the latest version of iOS but are getting an errorr message saying the phone is not eligible for the requested build. Try out the troubleshooting in this article named:
Error 3194 or "This device isn't eligible for the requested build"
http://support.apple.com/kb/ts4451
These steps will get you started, and there are additional troubleshooting steps if needed in the article:
Important: If you see one of these messages and need help updating or restoring your iOS device, Install the latest version of iTunes and try to update or restore again. After that, follow these steps if you need more help.
Check your "hosts" file
After you've updated iTunes to the latest version, you can check the hosts file to be sure your computer can contact the update server. Use the numbered steps below if you’re on a Mac.
If you’re using a Windows computer, follow steps in this Microsoft support article, noting that resetting the hosts file will affect software services that rely on hosts file redirects. If you're using Windows on a business computer, consult your IT department to be sure applications will still work correctly after resetting the hosts file.
In the Finder, choose Applications > Utilities.
Open Terminal.
Enter this command and then press Return:
sudo nano /private/etc/hosts
Enter the password you use to sign in to your computer and press Return. You won't see text appear in the Terminal window when you enter the password. Make sure you use a nonblank administrator password.
Terminal will display the hosts file. Navigate using the arrow keys and look for an entry containing “gs.apple.com”.
Add the # symbol and a space ("# ") to the beginning of the gs.apple.com entry.
Press Control-O to save the file. Then, press Enter when prompted for the filename and Control-X to exit the editor.
Restart your computer.
Try to update or restore your iOS device again.
Thank you for using Apple Support Communities.
All the very best,
Sterling

Checking for every record in a table using PL/SQL

Hello Gurus,
I would need your help in finding the best approach to tackle the below analysis using PL/SQL.
I have a table which contains two columns
UserID and Month
I want to find out the users who made orders every month for the first half of 2012.That is the User ordered on Jan 2012, Feb2012 ... and June 2012.
The Table is huge and has more than a million records. How do I approach this in PL/SQL.
Joe

Hi Justin,
Thanks for the quick response. This is helpful.However my Intention is to do it using PL/SQL for learning purposes. I am new to PLSQL.
I wanted to do something like looping through each records in the table for every user ID and If I find orders for six consecutive months for a particular user, I will insert the user id to a temp table.
Any hints on how can I use this? I heard about cursor. Can I use it. If so how should I approach.
--Joe

List of solutions for airplay icon missing in iTunes 11 (windows)

It seems like there are a lot of problems out there with airplay and iTunes 11. I think it would be great if Apple or someone were to make some sort of diagnostic tool for airplay.
I am starting this thread in an attempt to collect some of the various solutions to the airplay problems. Hopefully, other members of the community will add other solutions that they are aware of.
Problem: Can't find the airplay icon in iTunes 11 for windows
1) make sure you are looking in the right place. The icon will appear to the right of the volume slider in the normal iTunes view. If iTunes can't find any airplay devices, this icon will not be present and the area will just be blank.
2) For me (iTunes 11.0.5.5), I did some system work in Windows 8 64-bit, and installed AdAware, and uninstalled it. I think this reset my firewall settings. The airplay icon was missing from iTunes but I was able to do airplay from my iPad over the network. I searched the start menu for "firewall", started "Windows Firewall with Advanced Security", and in the Inbound Rules list I saw that I had 5 entries that started with "Airport". 2 of them were disabled. I double clicked on each disabled rule, and changed the action from "Block the connection" to "Allow the connection". After hitting ok and doing this for both blocked rules, I restarted iTunes and the airplay icon appeared and everything works fine.
3) A popular solution which has worked for me in the past has been to switch the program to miniplayer view. There you will hopefully see an airplay icon. Some people say you should select each of the entries in the airplay list here in order to get them to "stick." When you switch back to normal view, the airplay icon should remain visible.
4) I have seen someone update their dd wrt (open source based) router firmware and had the problem go away.
5) Some have had luck unplugging their airplay device (ie: receiver) for a few minutes and then plugging it back in.
Please add to this list if you can!

Windows 7 64bit
iTunes 11.1.2.32
Apple TV (New Shape) / Airport Express 3rd Gen.
I've had the issue of no Airplay button for the past few weeks. Strangely, it appeared randomly, but never stuck around for too long before disappearing. However, from reading this thread i uninstalled my wireless driver, and reinstalled from a generic windows search, and also installed Apple's Bonjour service (did this one after the other) and restarted my machine. All seems fine now, and the airplay button is there.
Thank you all so much for your inputs in helping get a resolution. I hope this works for everyone else with the issue.
Dan

How do I create a new folder for saving a PDF in Reader using Windows 8.1?

I used to be able to create a folder in which to save a PDF. With the new Reader in Windows 8.1, I have not found that option.

Wow. The light bulb just went off! I have the Reader that was installed on my HP notebook and - you are right - it is the Microsoft Reader. I just assumed it was Adobe's product which I have used for years. No wonder I can't find the options I generally used.
I will download the Adobe Reader. Thank you for your feedback and help!!!
Gail
Gail Klein

I'm trying to find driver for HP CD4e writer I'm using Windows XP

Heeft iemand die driver ter beschikking ?

Is that drive in an external case? THIS link indicates it is an external. If that is the situation, it could the the internals of the case is causing the problem.
{---------- Please click the "Thumbs Up" to say thanks for helping.
Please click "Accept As Solution" if my help has solved your problem. ----------}
This is a user supported forum. I am a volunteer and I do not work for HP.

Problem with vinyl recording

I specifically purchased the Soundblaster x-fi HD for vinyl recording to my computer. The problem is as the signal runs through the unit into my computer, i am unable to designate the different special effects available with this unit. I can record the record just fine but I was counting on being able to record vinyl and adding in the effects into the actual recorded file, but no matter what I do, i cannot get this to happen. Is it possible to do this with this particular unit, or if not, can you direct me to something that will? My email address is [email protected] Any info anybody can give me on this is deeply appreciated.

Jord, when I called it a "phenomenon" I did not mean to describe it as a bug or fault - you're right, it is a desireable feature of cycle recording.
As far as your question goes: Suppose you are recording track-by-track a song with two parts, an acoustic guitar and vocals, and the acoustic guitar part has an intricate eight-bar solo that needs to be redone. The advantage of using cycle recording and autodrop here is that you could define a cycle region giving you a two-bar intro (say) to the part you need to rerecord and a couple of bars of outro, making it easier to accomplish a musical phrasing. For example, say you're a vocalist trying to record a one-octave scale, and your pitch is off on the "fa-so." With cycle recording and autodrop, you could sing along with the "do-re-mi" and settle your pitch before rerecording the notes you flubbed, whereas (as I understand it) if you're just rerecording the "fa-so" in cycle mode, you won't get the "do-re-mi" as an intro after the first pass and would then just hope that you're nailing the notes you need to rerecord cold.
You can combine cycle recording with autodrop in Midi - why not in audio? It's a desireable feature in both.

E-MU 0204 for Vinyl Recording: Missing Sampling Rates Using Windows 7 Drivers?

Similar Messages

Maybe you are looking for