E1 PRI C1760V - unable to config pri-group timeslots 1-8,16

I'm trying to set-up a C1760 voice gateway with a VWIC-1MFT-E1 connecting to an ISDN30 PRI (E1)pri-group timeslots 1-8,16 on the controller E1 I get the following message:
%Controller tdm clock does not have data capability
Any idea's why I can't do this???
Thanks,
Chris
Cisco IOS Software, C1700 Software (C1700-ADVIPSERVICESK9-M), Version 12.4(10a),
ROM: System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
System returned to ROM by reload
System image file is "flash:c1700-advipservicesk9-mz.124-10a.bin"
Cisco 1760 (MPC860P) processor (revision 0x500) with 180224K/16384K bytes of mem
ory.
1 Ethernet interface
1 FastEthernet interface
1 Channelized E1/PRI port
32K bytes of NVRAM.
32768K bytes of processor board System flash (Read/Write)
Whenever I try to configure

This behavior is only seen when the c1751 or c1760 voice gateway has a T1/E1 VWIC installed and the T1/E1 controller is in a DOWN state, either due to an actual outage or even due to administrative shutdown. The T1/E1 controller can be set up for a voice pri-group, voice ds0-group, data channel-group, or even nothing at all -- the key is that the controller is DOWN. Once the T1/E1 controller is brought back up the OUT STATus for all POTS dial-peer will return to an UP state and calls may terminate again on those POTS dial-peers.
Workaround:
===========
Configure the command no dial-peer outbound status-check pots in global config mode.

Similar Messages

How to fake ISDN b-channels as busy out of the pri-group timeslots definition ?

Hi, Cisco Support Community,
This is my first post here, so I hope I won't make mistakes... First, thanks for reading me.
I wanted to reuse an old 2811 to act as a SIP gateway on an ISDN primary rate interface. This router is featured with 2 PVDM2-8 modules, so that we're able to handle up to 16 simultaneous calls. So I ordered a pri with 10 channels, which is supposed to be more than enough for our usage.
Everything works fine, excepted that I discovered that the PRI which was delivered to us is a full one, meaning 30 B channels.
As a result, as incoming calls are dispatched round robin by the isdn line provider, when incoming calls start to be presented on b-channel 16, the call is rejected by the router with a "channel unavailable" message... The only way to have a successful incoming call is then to have 15 more unsuccessful tries so that the calls are presented on B-channel 1 again :-/
I have to wait for monday to deal with the line provider to sort this out, but meanwhile, I was trying to find a workaround.
My first try was to use B-channel negotiation on the serial interface (isdn negotiate-bchan resend-setup), but it seems that b channel negociation is disabled on the provider side.
So the other obvious solution would be to fake channels 17 to 31 as busy (isdn busy b_channel xx) ... But as the pri-group timeslots are 1-16, the related serial interface is serial0/0/0:15, and I'm unable to set busy B-channels over 15. And of course, I have no way to define pri-group timeslots 1-31 as I have not enough DSPs to handle more than 16.
I also tried to use the ds0 busyout directive within the E1 controller configuration, but while the command is accepted, it does not appear in the configuration
Below is my running configuration... If some of you can help, this would be much appreciated. Current IOS on the router is Version 12.3(11)T3
Kind regards,
Philippe Martorell
--- cut here ---
Current configuration : 4311 bytes
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname RTR-xyz-abc
boot-start-marker
boot-end-marker
enable secret 5 xx
username user1 privilege 15 secret 5 xx
username user3 privilege 15 secret 5 xx
username user1 privilege 15 secret 5 xx
network-clock-participate wic 0
network-clock-select 1 E1 0/0/0
aaa new-model
aaa authentication login default local
aaa session-id common
ip subnet-zero
ip cef
ip name-server 8.8.8.8
ip name-server 8.8.4.4
no ftp-server write-enable
isdn switch-type primary-net5
voice-card 0
dspfarm
no local-bypass
voice call send-alert
voice call carrier capacity active
voice rtp send-recv
voice service voip
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
sip
no call service stop
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
controller E1 0/0/0
pri-group timeslots 1-16
translation-rule 1
Rule 1 ..% 900 international international
Rule 2 ..% 90 national national
translation-rule 2
Rule 1 ..% 02212345
interface FastEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-FE 0/0$
ip address 172.16.31.200 255.255.255.0
duplex auto
speed auto
no mop enabled
interface FastEthernet0/1
ip address 10.0.1.200 255.255.255.0
shutdown
duplex auto
speed auto
interface Serial0/0/0:15
no ip address
isdn switch-type primary-net5
isdn incoming-voice voice
isdn map address .* plan unknown type unknown
isdn negotiate-bchan resend-setup
isdn outgoing-voice info-transfer-capability 3.1kHz-audio
no cdp enable
ip default-gateway 172.16.31.254
ip classless
ip route 0.0.0.0 0.0.0.0 172.16.31.254
no ip http server
snmp-server community xx RO
control-plane
voice-port 0/0/0:15
no echo-cancel enable
playout-delay maximum 170
playout-delay nominal 80
playout-delay minimum low
cptone CH
bearer-cap 3100Hz
no mgcp piggyback message
dial-peer voice 1 pots
application session
incoming called-number .
direct-inward-dial
dial-peer voice 456389160 voip
destination-pattern 6[0-8]
translate-outgoing calling 1
translate-outgoing called 2
rtp payload-type cisco-codec-fax-ind 124
rtp payload-type nte 96
no modem passthrough
voice-class codec 1
session protocol sipv2
session target ipv4:10.200.3.21
dtmf-relay rtp-nte
fax rate disable
no vad
dial-peer voice 999999 voip
answer-address 0.
rtp payload-type cisco-codec-fax-ind 124
rtp payload-type nte 96
no modem passthrough
voice-class codec 1
session protocol sipv2
dtmf-relay rtp-nte
fax rate disable
fax protocol pass-through g711ulaw
no vad
dial-peer voice 9912 pots
destination-pattern 99123T
progress_ind alert enable 8
port 0/0/0:15
dial-peer voice 9920 pots
destination-pattern 99222T
clid restrict
clid restrict
port 0/0/0:15
dial-peer voice 456389162 voip
destination-pattern 69
translate-outgoing calling 1
translate-outgoing called 2
rtp payload-type cisco-codec-fax-ind 124
rtp payload-type nte 96
modem passthrough nse codec g711ulaw
voice-class codec 1
session protocol sipv2
session target ipv4:10.200.3.21
dtmf-relay h245-alphanumeric
fax-relay ecm disable
fax rate 9600
fax nsf 000000
fax protocol t38 ls-redundancy 2 hs-redundancy 2 fallback none
no vad
gateway
timer receive-rtp 1200
sip-ua
max-forwards 15
sip-server ipv4:10.200.3.21
banner login ^CCC
WARNING: This is a private network.
Unauthorized access is prohibited.
Use of this system constitutes your
consent to interception, monitoring,
and recording for official purposes
of information related to such use,
including criminal investigations.
^C
line con 0
line aux 0
line vty 0 4
password 7 xx
scheduler allocate 20000 1000
end

Hi,
Thanks for your answer, but unfortunately, this did not help. commands ds0 busyout are accepted, but not taken into account :
RTR-505-012#conf t
*Apr 7 10:23:04.361: %SYS-5-CONFIG_I: Configured from console by sysadmin9 on vty0 (172.16.0.88)
Enter configuration commands, one per line. End with CNTL/Z.
RTR-505-012(config)#controller e1 0/0/0
RTR-505-012(config-controller)#ds0 busyout 17-31
RTR-505-012(config-controller)#do sh run | begin controller
controller E1 0/0/0
pri-group timeslots 1-16
And the "isdn service b_channel state" commands in the serial interface context are rejected
RTR-505-012(config-controller)#interface Serial0/0/0:15
RTR-505-012(config-if)#isdn service b_channel 16 state 2
%The service state of reserved channel 16 on DSL 0 can not be changed.
While the "show isdn service" status shows channels 16 to 30 are out of service, some incoming calls are still directed to these channels by the provider :
RTR-505-012#show isdn service
PRI Channel Statistics:
ISDN Se0/0/0:15, Channel [1-31]
Configured Isdn Interface (dsl) 0
Channel State (0=Idle 1=Proposed 2=Busy 3=Reserved 4=Restart 5=Maint_Pend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
Service State (0=Inservice 1=Maint 2=Outofservice 8=MaintPend 9=OOSPend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
*Apr 7 10:20:45.509: %ISDN-6-CHAN_UNAVAILABLE: Interface Se0/0/0:15 Requested Channel 19 is not available
*Apr 7 10:20:53.353: %ISDN-6-CHAN_UNAVAILABLE: Interface Se0/0/0:15 Requested Channel 20 is not available
I'll try to sort this out with the provider today.
Thanks,
Philippe.

AS5300 is reloading instantly on "pri-group timeslots 1-31" settings

Hello,
On AS5300 when any of the 4 E1 ports is connected and the "pri-group timeslots" are enabled the gateway instantly reloads, I can't see any error message. I have tried the following tests on my Cisco AS5300
1. software loopback on the ports - it does not restart (on     "pri-group timeslot" setting).
2. tried to disconnect one port from a functional gateway ( Cisco AS 5300, with same configuration)     and connect it to a port of new Cisco - it restarts (on "pri group     timeslot" setting)
3. with all cables disconnected and "pri-group timeslot" setting it     is working without restart, after the cable is plugged in, it     restarts
4. hardware         loopback on any of the ports and "pri-group timeslots" - it         restarts
5. Power off , plug out the module         boards (E1 and DSP boards), plug in the boards and power on -         doesn't help it keeps to restart on the "pri group timeslot"         setting
What could cause this issue?
Thank You,
Szabolcs Szasz

What is the IOS version of your AS5300?
In "show ver" information, what is the reboot cause? Is it a crash?
Probably the command "pri group timeslot" creates an unexpected condition that causes the crash.
In my experience an IOS upgrade solves this issues.

Pri-group command

Hi;
I'm trying to configure my E1 controller on 2621XM router with having IOS (c2600-ipvoice-mz.123-7.T10.bin), but it's not showing in the controller configuration mode!!
please help how to enable it? and/or if there is some specific IOS release to support this command pri-group timeslots ...!
thanks

If you have a voice feature set the command should appear if you have the correct hardware.
Do you have a DSP card in your router?
Do a show diag and show voice dsp, maybe post the results if you're unsure...
Aaron

Unable to view the groups in Oracle Internet Directory

Hi Experts,
We have created groups in ContentDB by executing the Groups.java program provided with cdbdevkit.
We could able to view the groups in ContentDB Web UI.
HowEver when logged onto OID....we are unable to view the groups.
How can i view the groups(Created in ContentDB) through OID.
Thanks
parker.

Hi Experts,
We have created groups in ContentDB by executing the Groups.java program provided with cdbdevkit.
We could able to view the groups in ContentDB Web UI.
HowEver when logged onto OID....we are unable to view the groups.
How can i view the groups(Created in ContentDB) through OID.
Thanks
parker.

SAP QM unable to pick Code group & code in creation of defect in QA32

Hi every one,
I am new to QM , can any one guide me to solve this issue.
In T code QA32 after results recording, am trying to maintain defect document of one of reject MIC. But, i am unable to pick Code group or code. System showing error "Code group QM-Q contradicts the code group of the catalog profile "
Regards
Srinivas

Hello Srinivas,
Check below path and let me know what settings you have maintained.
Now, Also check your Catalogs profile, You have to maintain Catalog "Z" for the same catalog profile.
Amol.

HT4790 My Mac OS Lion 10.7 FileVaulted HD does not boot, prohibitory sign, stop sign appears some minutes after boot starts. Disk Utility repair shows four error messages: Unable to bootstrap transaction group 2517: inconsistent crosscheck (the same with

My Mac OS Lion 10.7 FileVaulted HD does not boot, prohibitory sign, stop sign appears some minutes after boot starts. Disk Utility repair shows four error messages:
Unable to bootstrap transaction group 2517: inconsistent crosscheck
No valid commit checkpoint found
The volume xxxxxxxxxxxxxx(here it shows physical volume number) was found corrupt and can not be repaired.
Problems were encountered during repair of the partition map
Error: Storage system verify or repair failed.
(the same with 2518, 2519 and 2520 transaction group)
I suppose it is serious bug in Mac OS Lion managing FileVault and wonder what the help could be?

Most likely culprit is your Lacie drives which are notorious for flaky power supplies which cause just the sort of erratic behaviour that you describe. Have had similar issues myself. Lacie has been good about replacing my power converter-- twice. If you have seven of them, good luck finding the bad one or more. Like I said, the behaviour is erratic. Sometimes it'll work sometimes not. I can't comment on Samsung drives because I've never used them and have never heard anything about them. Same with Softraid. Why not just use Disk Utility. Sounds like you're ready for an external hardware raid. This will be much faster, much more reliable, and may even be cheaper than seven firewire drives. Check out G Tech, and Maxx Digital for starters.
Best of luck
Terry

DiskUtility error: unable to bootstrap transaction group

I get this bootstrap error with a checksum mismatch but searching only found 1 other person with 'chksum mismatch' with 1 reply which was not of use.
"Unable to bootstrap transaction group 611: cksum mismatch
Unable to bootstrap transaction group 609: cksum mismatch"
MacBook Pro 13" early 2011, 10.7.2, Kingston 60 GB SSD as boot volume. FileVault full disk encryption is enabled.
I get this error when use Verify Disk when booted from the volume or even when I try to Repair Disk when I boot from a Lion flash drive or in target mode.
I also get the green OK messages at the end but when I Verify/Repair again, it still shows the same bootstrap errors. Why does this happen? Why doesn't DiskUtility fix it? Is it a bad error? Seems odd that it says OK at the end but still shows the errors.
Thanks.

I'm seeing this issue too. Disk repair wont fix it:
Verifying volume “Macintosh HD”
Checking storage systemChecking volume.
disk0s2: Scan for Volume Headers
disk0s2: Scan for Disk Labels
Logical Volume Group 2008965E-D094-4248-A616-CCADC11CCCFE spans 1 device
Logical Volume Group has a 16 MB Metadata Volume with double redundancy
Start scanning metadata for a valid checkpoint
Load and verify Segment Headers
Load and verify Checkpoint Payload
Load and verify Transaction Segment
Load and verify Transaction Segment
Incorporate 1 newer non-checkpoint transactions
Load and verify Virtual Address Table
Load and verify Segment Usage Table
Unable to bootstrap transaction group 2149: inconsistent crosscheck
Continue scanning metadata for an older checkpoint
Load and verify Segment Headers
Load and verify Checkpoint Payload
Load and verify Transaction Segment
Incorporate 0 newer non-checkpoint transactions
Load and verify Virtual Address Table
Load and verify Segment Usage Table
Unable to bootstrap transaction group 2148: inconsistent crosscheck
Continue scanning metadata for an older checkpoint
Load and verify Segment Headers
Load and verify Checkpoint Payload
Load and verify Transaction Segment
Incorporate 0 newer non-checkpoint transactions
Load and verify Virtual Address Table
Load and verify Segment Usage Table
Unable to bootstrap transaction group 2147: inconsistent crosscheck
Continue scanning metadata for an older checkpoint
Load and verify Segment Headers
Load and verify Checkpoint Payload
Load and verify Transaction Segment
Incorporate 0 newer non-checkpoint transactions
Load and verify Virtual Address Table
Load and verify Segment Usage Table
Unable to bootstrap transaction group 2146: inconsistent crosscheck
No valid commit checkpoint found
The volume 2008965E-D094-4248-A616-CCADC11CCCFE was found corrupt and needs to be repaired.
Error: Storage system verify or repair failed.

Unable to create Product group form T Code- MC84 in ECC 6.0

Dear Expert,
After Upgrade from 4.7E to ECC 6.0 we are facing problem for Tcode-MC84(Create Product Group) is opening but we are unable to Create product group..
can any tell me what is problem for this or is there any apply SAP Note for this.
Thanks in advance,
Regards,
Kumar,

Hi,
I think for some particular versions you can create a product group directly using T code MC84, and if u have got a material type say PROD-Product group,then use mm01 for creating a product group. And then you can do the change in MC86 for product group.
Refer thread:
https://forums.sdn.sap.com/click.jspa?searchID=15761932&messageID=5854286
Regards,
R.Brahmankar
Edited by: R Brahmankar on Sep 1, 2008 12:42 PM

Unable to bootstrap transaction group: inconsistent crosscheck

Disk Utility reports the following errors when I run it on my startup disk 'Macintoch HD'. When I click 'repair' it is not able to complete the repair and suggests to reboot from the recovery disk. When I do that and run DU on 'Macintosh HD', it reports no errors and shows a green result message. I can repeat the reboots and checks with the same results.
What does this mean and how do I resolve it, shy from reinstalling everything?
Verifying partition map for “TOSHIBA MK7559GSXF Media”
Checking prerequisites
Checking the partition list
Checking for an EFI system partition
Checking the EFI system partition’s size
Checking the EFI system partition’s file system
Checking all HFS data partition loader spaces
Checking Core Storage Physical Volume partitions
Checking storage system
Checking volume.
disk0s2: Scan for Volume Headers
disk0s2: Scan for Disk Labels
Logical Volume Group 6BE3FFB1-1BA7-4853-9AD3-3E896542D4D7 on 1 device
disk0s2: Scan for Metadata Volume
Logical Volume Group has a 16 MB Metadata Volume with double redundancy
Start scanning metadata for a valid checkpoint
Load and verify Segment Headers
Load and verify Checkpoint Payload
Load and verify Transaction Segment
Incorporate 0 newer non-checkpoint transactions
Load and verify Virtual Address Table
Load and verify Segment Usage Table
Load and verify Metadata Superblock
Load and verify Logical Volumes B-Trees
Logical Volume Group contains 1 Logical Volume
Load and verify A92E6BFF-144E-4BE7-99B0-D25B2F01B4BF
Load and verify 1D173D02-CDDD-4262-A070-69FB6B2DDE16
Load and verify Freespace Summary
Load and verify Block Accounting
Load and verify Live Virtual Addresses
Unable to bootstrap transaction group 5913: inconsistent crosscheck
Continue scanning metadata for an older checkpoint
Load and verify Segment Headers
Load and verify Checkpoint Payload
Load and verify Transaction Segment
Incorporate 0 newer non-checkpoint transactions
Load and verify Virtual Address Table
Load and verify Segment Usage Table
Load and verify Metadata Superblock
Load and verify Logical Volumes B-Trees
Logical Volume Group contains 1 Logical Volume
Load and verify A92E6BFF-144E-4BE7-99B0-D25B2F01B4BF
Load and verify 1D173D02-CDDD-4262-A070-69FB6B2DDE16
Load and verify Freespace Summary
Load and verify Block Accounting
Load and verify Live Virtual Addresses
Unable to bootstrap transaction group 5912: inconsistent crosscheck
Continue scanning metadata for an older checkpoint
Load and verify Segment Headers
Load and verify Checkpoint Payload
Load and verify Transaction Segment
Incorporate 0 newer non-checkpoint transactions
Load and verify Virtual Address Table
Load and verify Segment Usage Table
Load and verify Metadata Superblock
Load and verify Logical Volumes B-Trees
Logical Volume Group contains 1 Logical Volume
Load and verify A92E6BFF-144E-4BE7-99B0-D25B2F01B4BF
Load and verify 1D173D02-CDDD-4262-A070-69FB6B2DDE16
Load and verify Freespace Summary
Load and verify Block Accounting
Load and verify Live Virtual Addresses
Unable to bootstrap transaction group 5911: inconsistent crosscheck
Continue scanning metadata for an older checkpoint
Load and verify Segment Headers
Load and verify Checkpoint Payload
Load and verify Transaction Segment
Incorporate 0 newer non-checkpoint transactions
Load and verify Virtual Address Table
Load and verify Segment Usage Table
Load and verify Metadata Superblock
Load and verify Logical Volumes B-Trees
Logical Volume Group contains 1 Logical Volume
Load and verify A92E6BFF-144E-4BE7-99B0-D25B2F01B4BF
Load and verify 1D173D02-CDDD-4262-A070-69FB6B2DDE16
Load and verify Freespace Summary
Load and verify Block Accounting
Load and verify Live Virtual Addresses
Unable to bootstrap transaction group 5910: inconsistent crosscheck
No valid commit checkpoint found
The volume 6BE3FFB1-1BA7-4853-9AD3-3E896542D4D7 was found corrupt and needs to be repaired.
Problems were found with the partition map which might prevent booting
Error: This disk needs to be repaired. Click Repair Disk.

hshshs wrote:
I had exactly the same problem with Disk Utility reporting "Unable to bootstrap transaction group xxxx: inconsistent crosscheck" errors when booted from Macintosh HD but no errors when booted from the Recovery HD. The following resolved it for me:
1. Turn off FileVault; decrypting the drive took about an hour
2. Run Disk Utility - reported two Macintosh HD, one greyed out
3. Reboot (to see if it resolved 2)
4. Run Disk Utility from Macintosh HD again; only one Macintosh HD and no errors reported
5. Turn on FileVault; encryption took another hour or so
6. Reboot again
7. Run Disk Utility from Macintosh HD again; no errors reported
No reformatting, reinstalling or replacing hard drives, as other reports have suggested.
MacBook Air, 13-inch, Late 2010, OS X 10.8.4, 256GB SSD
Thanks! Worked for me.

Disk Utiliy error on Disk Repair - Unable to bootstrap transaction group cksum mismatch

When I try to Repair my Hard Disk on Disk Utility (command+R recovery mode) it shows this error:
My hard disk is encrypted with filevault 2 and Disk Utility seems to be unable to decrypt it.
Can I do something with bash? Thank you.
Checking volume.
disk0s2: Scan for Volume Headers
disk0s2: Scan for Disk Labels
Invalid Disk Label @ 319200587776: cksum mismatch
Invalid Disk Label @ 319204782080: cksum mismatch
Logical Volume Group 573A27F3-05AE-45D8-8C36-C2190AA709A0 spans 1 device
Logical Volume Group has a 16 MB Metadata Volume with double redundancy
Start scanning metadata for a valid checkpoint
Load and verify Segment Headers
Load and verify Checkpoint Payload
Load and verify Transaction Segment
Incorporate 0 newer non-checkpoint transactions
Load and verify Virtual Address Table
Load and verify Segment Usage Table
Load and verify Metadata Superblock
Load and verify Logical Volumes B-Trees
Logical Volume Group contains 1 Logical Volumes
Load and verify EBE1F6D9-1560-4837-BFE4-A8C45CE0252A
Load and verify 1F61CB62-C529-4301-AF2E-B71933C040C3
Unable to bootstrap transaction group 2601: cksum mismatch
Continue scanning metadata for an older checkpoint
Load and verify Segment Headers
Load and verify Checkpoint Payload
Load and verify Transaction Segment
Incorporate 0 newer non-checkpoint transactions
Load and verify Virtual Address Table
Load and verify Segment Usage Table
Load and verify Metadata Superblock
Load and verify Logical Volumes B-Trees
Logical Volume Group contains 1 Logical Volumes
Load and verify EBE1F6D9-1560-4837-BFE4-A8C45CE0252A
Load and verify 1F61CB62-C529-4301-AF2E-B71933C040C3
Unable to bootstrap transaction group 2600: cksum mismatch
Continue scanning metadata for an older checkpoint
Load and verify Segment Headers
Load and verify Checkpoint Payload
Load and verify Transaction Segment
Incorporate 0 newer non-checkpoint transactions
Load and verify Virtual Address Table
Load and verify Segment Usage Table
Load and verify Metadata Superblock
Load and verify Logical Volumes B-Trees
Logical Volume Group contains 1 Logical Volumes
Load and verify EBE1F6D9-1560-4837-BFE4-A8C45CE0252A
Load and verify 1F61CB62-C529-4301-AF2E-B71933C040C3
Unable to bootstrap transaction group 2599: cksum mismatch
Continue scanning metadata for an older checkpoint
Load and verify Segment Headers
Load and verify Checkpoint Payload
Load and verify Transaction Segment
Incorporate 0 newer non-checkpoint transactions
Load and verify Virtual Address Table
Load and verify Segment Usage Table
Load and verify Metadata Superblock
Load and verify Logical Volumes B-Trees
Unable to bootstrap transaction group 2596: cksum mismatch
No valid commit checkpoint found
The volume 573A27F3-05AE-45D8-8C36-C2190AA709A0 was found corrupt and
needs to be repaired.

MRDJones wrote:
… I replaced hard drive …
That was sensible.
… I used a external enclosure on the failed hard drive but I get the same error when trying to use disk utility on it. … The drive will not mount.
Those symptoms are consistent with a failing or failed hard drive.
Related
Storage problems, Core Storage, Disk Utility, checksums, fsck_cs and cksum mismatches

Unable to bootstrap transaction group 7845 when attempting to fix harddrive with disk utility

Hello,
I recently tried burning a cd from the Mac. I pressed cancel because do forgot to put it at the right speed. So I kept clicking cancel them eventually shut it down. I started it up and I got a "prohibited" sign.
The topic title is their error I get.
(unable to bootstrap transaction group 7845)

No
I dont have enough money to buy one of those "time machine" thingys.
But it's ok. The only thing that is valuble to me was my documents, and they're all sent to my email .
BDAqua wrote:
I was afraid of that after posting then re-reading your title! (
Do you have a Backup?

Warning! task_eval_init(): unable to set User/Group baseDN

Hi,
I have installed Directory server on Unix platform.
Installation went successful. While doing the installation, I have given the userid to run the server as "admxxx" and group as "www".
After the installation, the server started properly but with a warning message that "warning: daemon is running as super-user". And I was able to open the console and do whatever I wanted.
We have created 3 more directory server instances and we imported an LDIF file into one of the instances successfully.
Now the problem is, whenever we start the admin server, we are getting the following message.
bash-2.03# ./start-admin
Info: Cache expiration set to 600 seconds
Warning! task_eval_init(): unable to set User/Group baseDN
Netscape-Administrator/4.2 B2002.057.2313
startup: listening to http://servername, port 6061 as root
warning: daemon is running as super-user
Can any one tell why I am getting the message Warning! task_eval_init(): unable to set User/Group baseDN ?
This is very urgent. We have configured this LDAP to SiteMinder server.
Thanks in Advance,
Murthy

zhangping,
I don't recognize your error. But are you using ldap for logging into SunMC ? This is not possible.

Unable to create server groups

Hi All,
I am unable to create server groups on Business Objects 3.1 Edge server. It has been updated till SP 4. I get the following error
"This operation is not permitted with your current set of license keys. Upgrade your license keys to enable this operation. (FWB 00015)"
Is this a limitation of BO edge series?
Cheers,
AK

Hi Alok,
Are you using Temporary license ? if not, please try below
Replace the file "libkeydecoder.so" in <BOE install dir>/bobje/enterprise120/<platform> with the file from your install CD.
Regards,
Arjun

Unable to arrange iChat Groups

Hi,
I'm in the process of switching from Adium to the latest iChat Version 6.0 (927) on latest Lion 10.7.1. Curiously, after adding the first Yahoo account, I find that I'm unable to rearrange my groups (tried the usual dragging of group labels - they just won't budge, and stay in alphabetical order). Tried delete and re-add, randomly change some settings, deleted *ichat* files and dirs in Cache and Prefs directories, to no avail. I tried adding the same Yahoo account on my friend's macbook (the same environment) with no problems. Maybe I have missed something obvious - would appreciate any help.
Thanks.
--sazli

Hi,
In earlier versions of iChat when Buddy List were separate you could click the Plus button at the bottom of the Buddy List and chose Edit Groups
Then you could drag the list in to the order you wanted
I seem to remember that you could not drag something to the very top. You had to drag it to second place then drag the top item down.
If you have several Buddy List go to the iChat > Preferences > General Section and deselect the Link Buddy List option.
Then tackle Buddy Lists directly.
AIM Buddy list as an example.
If you had a second Login (Allow Multiple Logins) and that other Login was active then it will continually override any new setting you try to tell the server.
Other Apps, AIM Express, the default Login period at the AIM web site can be causes.
Google and other Jabber accounts
These allow Multiple logins by default.
The app or login with the highest Priority takes precedence.
iChat can not change it's Priority and this is the same as Logging in to Google Mail or iGoogle and chatting there.
Presumably other Jabber Servers are the same but rarely can you assess the chat function via a web site like Google.
Google web pages also have a default login period.
AIM and Goolge's default Login period is two weeks !!!
10:53 PM Thursday; August 25, 2011
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb( 10.6.8)
 Mac OS X (10.6.8),
"Limit the Logs to the Bits above Binary Images."  No, Seriously

E1 PRI C1760V - unable to config pri-group timeslots 1-8,16

Similar Messages

Maybe you are looking for