E1000 works behind E3500 as access point but not behind Airlink AR675W and ideas?

In my own home just testing my E1000 works fine as an access point with an E3500 as primary router using Linksys
method 1 (lan-lan connection) with E1000 IP reset to 192.168.1.2 and DHCP off and with
method 2 (lan-wan) with E1000 IP reset to 192.168.2.1 and DHCP On and different wireless SSID.
In my daughters building where I need it, I cannot get the E1000 to work as an access point. The primary router is an Airlink AR675W with ip 192.168.0.1 (255.255.255.0) delivering addresses 100 to 150.
When i try the E1000 in either method I get no internet connection on devices connected hardwired or wirelessly to the E1000. Before each setup I used the reset button and the factory defaults tab
method1 (lan-lan) I set the E1000 to IP 192.168.0.2 to be different than the Airlink and DHCP off.
method2 (lan-wan) with E1000 IP reset to 192.168.2.1 and DHCP On and different wireless SSID.
Are there any ideas why I cannot connect to the internet in this way behind the Airlink primary router

ok - i will read up on the airlink - it is a landlord situation but he will probably let me do a few things to it.
Also I see the Airlink admin IP default is 192.168.2.1 and not 192.168.0.1 like I thought so that might make a difference.
I don't know what flash DD-WRT means. Its a 10 minute drive to the other house. The internet provider is SHAW cable and I do not know the modem but it is probably Motorola SB5100 or SB5102 wired modem. The problem is it is a large house with concrete walls & floors & double pane windows so the wireless signal downstairs is weak. ethernet cables are probably ok but I'll take some more with me. The ethernet jack downstairs definately works as I can connect a single PC to it.

Similar Messages

WRT 54G conected to access point but not internet

Hi There
The wireless router is working an can get to the internet on PC
My other PC see's the access point but
will not connect to the internet
Signal strengh andLink quality are good, looking at the
PCI Linksys adapter box
any thoughts?
Thanks

Whats the OS installed on your computer. In the system tray you will find the linksys monitor...right click on it and select "Use windiws XP configuration" ... once its done ... next to that you will find "Wireless Network Connection" icon ... Right click on it and select "View Available Wireless Network".... select your network... when prompted for "Network key" type in your security key and click on 'Connect' ... After this see if you are able to go online or not.

I have an airport express, which I want to use with my broadband providers router to create a second wireless access point but not with the same network name etc.

In effect, I want to have my providers router working upstairs and the aiport express downstairs connected via wi fi. The airport would have a different network name, then allowing me to connect the children to the access point. This would allow me to turn their network off at times of day etc.
any ideas ?

I want to have my providers router working upstairs and the aiport express downstairs connected via wi fi
Sorry, but the AirPort Express....or any other Apple router......cannot do this.
In order to do what you want, you will need to establish an Ethernet connection from one of the LAN <-> ports on your "main" router to the WAN "O" port on the AirPort Express.
Configure the AirPort Express to "create a wireless network" using a wireless network name, and password that you select. As far as controlling connections, you can use the settings in Timed Access to establish rules about when the kids and cannot connect.

WRT160N Useable as a switch/access point but not as an internet gateway?

Greetings,
Can anyone tell me if it is possible to use a
WRT160N wireless N router as just a switch and wireless LAN access point and NOT as an internet Gateway? I have a LAN that is not connected to the internet that uses a Linksys switch and I need to get a wireless access point setup so that I can attach a computer wirelessly to this LAN. Occassionally I connect the swich to another router that does have internet access, but in general the LAN is not connected to the internet router.
Thanks!

You can use WRT160N as a switch...Connect the LAN to the Ethernet port of the router and change the ip address of the linksys router in the range of the LAN ip.

My iPod Touch 4G connects to access point, but not the internet.

I'm stuck for ideas, so any help is appreciated! I've gone through the troubleshooting guide, and none of that helped. I've reset my network settings, forgetting the specific network, resetting the router, resetting the iPod, restoring it to factory settings, upgrading to the latest firmware, and nothing has worked.
Sometimes, if I forget the network and reset my iPod, it may (but not always) work for that session. Whenever I try again, I have to repeat this process and HOPE it works.
I can't try on another network because that's not available to me and won't be for a while.
This happened really randomly. Nothing changed, and it's driving me mad. Any help is appreciated a lot!

Does it connect to the internet with other networks?
- If so that indicates a problem with your router. Likely time for a new router.
- If not that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

I added greasemonkey and it works with two of my games but not the third one and these are the same type of games Dragons ofAtlantis on Facebook. Why would it work on two and not the third?

I have windows 7 and firefox 6.0 greasemonkey I had just installed this program

1. If you break your post into paragraphs it is much easier to read.
2. I have no idea what your post is referring to, and how - if at all - it relates to iPhoto.
3. It's a good idea to re-read what you've posted, and ask yourself how it might look to someone who doesn't know you and doesn't know what's going on with your machine.

Wireless bridging is not working in 1552 outdoor access point and 2602e indoor access point.

Hi,
I am have been tested wireless bridging with 2 indoor Cisco 2602 access point by following the attached document and its working fine without any issue.
After then I made one Cisco 1552 EU-M-K9 outdoor access point as RAP, then connect to this RAP with one 2602 mesh access point. But its not working, mesh access point is just start scan the signal to get associate with RAP, but not getting established. Is there any specific configuration required to connect between outdoor and indoor access point. Kindly find the attachment and advise.
regards,
Jubair.S

Hi Team,
Any suggestion??
Regards,
Jubair.S

LinkSys Wireless Card connects to "Access Point" but no internet connection

I have 2 LinkSys wireless cards. one is 802.11g, the other b. The signal for the Airport Extreme 802.11n Wi-Fi Wireless Base Station is very strong, but when I try to connect, it says "You are connected to the access point, but the Internet cannot be found". No internet access, and I can't ping anything (Ping request could not find host...). And of course the printer hooked to the AirPort is also not recognized. My iMac and Macbook both have no problems connecting to the network. There is no problem with ethernet connection to the Airport. Is it possible to have a compatibility problem between the Linksys and Airport hardware? I thought as long as they were were compatible 802.11, they would work together. The cards had no problem with my old DLink router or other hotspots in the city. Is there a set-up I missed for setting up the PC-based cards with the AirPort?

Is your wireless network secured?
The box said windows xp or better... So I installed Linux!

Connected to access point but internet cannot be found????

router was working fine until it wasnt finding internet one nite and then it was unplugged so internet could be used on main computer and now when i try to plug everything back up to get wireless internet, it still says connected to access point but internet not found dont have a clue what is going on!?!

I think you were connecting to wireless router to access Internet, you need to have proper configuration on wireless router and wireless adapter to make it work, take a look on this wireless network setup tutorial to help you.

Can cisco MSE(mobility service engine) configured to work with non-cisco access points?

I understand that access points can be configured to forwards all the probe requests to cisco wifi controller. cisco MSE(mobility service engine) gets the probes from wifi controller to find the location of the mobile devices.
My question, can cisco MSE(mobility service engine) be configured to work with non-cisco access points?

No and the reason why is the NMSP communication from the MSE to the WLC. Other vendors don't support this so there is no communication happening.
-Scott

Asking to enter a device password in the access point but I don't have an access point

I installed the Intel Proseet Wireless Client and upon connection to my Linksys router a wizard comes up asking me to "enter the device password to my access point or external registrar". It displays an 8 digit number in the device password field. My only option at that point is to go "back", "next" or "cancel". If I click "next" it eventually fails to connect to my wireless router. I do not have an access point installed. Only the router and cable modem. Any suggestions would be appreciated.
Message Edited by dougieg on 11-06-2009 05:12 PM

If its asking you for the Access Point password when you are trying to connect to your Wireless Network, It means you need to input the Wireless Security Key which you have setup on your Router.
When you are trying to connect to your Wireless Network and it ask you for the 8 digit password, you need to Flip your router upside down and below you will find a 8 digit pin number (0000-0000) it will be in these format. Just input the 8digit pin without (-) and click on Next and it will connect you to your wireless network. Once successfully connected to your Network wirelessly you should be able to go online Wirelessly from your Computer.

I have a time capsule connected directly to fiber connection. I have connected a windows server directly to TC and configured it for remote desktop connection. From my interanet I can access srvr but not from my home. What config I need on TC?

I have a time capsule directly connected to fibre optic point out. All pcs and macs are connected wirelessly to the internet. I have connected a windows server pc to TC. When configured for Remote desktop connection, I can access windows server from within interanet but don't know how to access it from internet. I guess I need to change some settings in TC to get some ip adress for the remote desktop connection from my home. Anyone who can help me out? Appreciate it.
Narmin

I am a little lost now.. I have read again your title and your first post.. and they seem inconsistent.
In the title you state.
From my interanet I can access srvr but not from my home.
Interanet is not a word I know.. I assumed intranet...are you talking about internet or intranet? And just to be clear say WAN or LAN.. !! Is your home part of the interanet??
In the first post you state,
I can access windows server from within interanet but don't know how to access it from internet.
Now this is more normal.. the issue is not in the home at all, it is accessible from there but fails from internet. If this is correct, then you can do a few obvious things to determine where the problem is.
But first I need to know are you actually testing from a different internet connection to your home lan.. you are not just trying the public IP from inside the LAN as that will fail due to the TC not doing NAT Loopback.
I am also assuming the TC is the only router in the network, and has the public IP on the WAN interface.
And I am also assuming you have turned on the ping responder and you can actually ping your public ip from the internet and get a response. This helps no end in figuring out where there are issues. Strange but I have no idea if there is a ping responder in the TC WAN so you might need to forward that as well. Also if you have a dynamic public ip address are you using dyndns or no-ip or some other service to connect.
1. Test bypassing the TC.. plug the internet connection straight into the windows server,, and test if you have access. If yes, the TC is the problem.. if not, your setup on the windows server is wrong.. look at firewall in particular.
2. Assuming from test 1 the TC is the problem, Post the screen shots of the port forwarding setup for us to look at.. that is by far the easiest way to check it out.
There are lots of references to port forwarding in the TC.. eg
http://must-know-mac.blogspot.com/2008/07/how-to-port-forward-time-capsule.html
The things that generally go wrong are firewall on the computer that is accepting the port.
The ISP doesn't allow connections on a particular port. (not likely in your case)
The router is behind another router.. double NAT will kill any port forward.
Upnp has already allocated a port.. not an issue as TC doesn't use upnp although a reboot of everything after you set port forwards is well worth it.. amazing how things don't stick properly without a reboot.
IP on the receiving device is not static and so changes.
Not enough or right type of ports are opened. This is always messier than it looks as one port is often not enough for two way communications.

Access point are not coming up after upgrade image of WLC

Hi,
I have AIR-WLC4402-50-K9 WLC i that current IOS is 7.0.98.218 and i upgraded with 7.0.116.0 IOS but after upgrading and reboot the WLC from 15 access point 3 access point are not coming up and 12 are coing up and working fine (4 1142 and 11 1131 series access point) 3 which are not coimg is 1131 series access point. when i login with console to 3 access point its rebooting 2 times and coming on ap: prompt.
In between that i reloaded the WLC one more time because from 15 acess point only 4 aceess point are came up and i also cleck the show boot on wlc its output is
7.0.116.0 (default)
7.0.98.218 (active)
so i reload the wlc and checked out of 15 acess point now 12 acess point are up and still 3 are not. And i also checked the output of show boot command its
7.0.116.0 (default)(active)
7.0.98.218
So i things its because of when 2nd time i reload the wlc the remaining 3 access point are getting image from wlc but because of reload its connection should be loss and error loading flash error are coming on acess point.
After that i recover the IOS for access point and convert into autonomus and from autonomus convert into Leightweight Access point. I also attached the procedure for recover the ios of access poing
But my question is why this 3 access point are not coming up is this happen's after upgrading wlc can any one please send me Step by Step WLC S/W Upgrade' process and if this this happens some time please send me any doccument related to this.

Sunil,
When you rebooted the controller did you do it from the Web GUI, the CLI, or did you physically reboot the controller? I believe and maybe incorrect but if your getting the ap: < prompt > that means that there is no firmware on the unit. If you have restored these to functioning autonomous unit and then re-converted them to Lightweight and it's still happening then we need to look at a debug output of what is happening when those AP's attempt to join the controller.
The capture you attached shows that it appears to join the controller and get a config, but are you saying that when it reboots again it stops working?? the other thing I would reccomend is clear out the flash memory since your capture shows the possibility that there are several copies stored there.
Hope this helps.

My transparency does not work on my iPhone and I was wondering how I fix that? It worked when I first downloaded ios7 but not now.

My transparency does not work on my iPhone and I was wondering how I fix that? It worked when I first downloaded ios7 but not now.

Hello wilsontot_too,
Thank you for the details of the issue you are experiencing on your iPhone. It sounds like you are not noticing transparency on your iPhone. It may be that you have "Increase Contrast" turned on in your iPhone settings.
I recommend verifying that Increase Contrast is turned off in Settings>General>Accessibility.
iPhone User Guide - Large, bold, and high-contrast text
http://help.apple.com/iphone/7/#/iph73b89c6
Thank you for using Apple Support Communities.
Best,
Sheila M.

I cannot get GPS Only to work on my ipad3 (4g version, but not on an active cell plan, and wifi off). Is there some new requirement in 7.1 or 7.1.1 to have cell and/or wifi enabled for GPS to work? I am testing with MotionX

It seems like I cannot get GPS only to work on my ipad3 (4g version, but not on an active cell plan, and wifi off). Is there some new requirement in 7.1 or 7.1.1 to have cell and/or wifi enabled for GPS to work? I am testing with MotionX, garmin blueChart mobile, and a GPS monitoring tool. All show no signal. If I turn on cell and wifi, it says I get gps signal, but can't tell if that is from the GPS chip, or just from cell and wifi only (maybe with some gps mixed in)? Any ideas on how to get iPad working with GPS only??

Roger that. Thanks for your time.
System:
Windows 7 64bit
Processor: AMD phenom IIX4 965
RAM: Gskill Ripsaw F3-12800CL7D-4GBRM (2-2GB sticks)
GPU:EVGA Classified Nvidia GeForce GTX 560 Ti 448 core
PSU: Kingwin 1000W laser gold (LZG-1000)
Yes. tried the one ram stick, no go. I have been trying to boot off/install the windows 7 disk but am unable to get to the point where windows starts installing after its gathering information portion of the install. I can get to the disk selection screen of the install with the WD HD on SATA port 2 but then get the "cant install messages" when I try to select the Vertex 3. Yes I can see the Vertex 3 Drive as well as the WD drive at this point. some times I have to hit "scan" a couple of times.

E1000 works behind E3500 as access point but not behind Airlink AR675W and ideas?

Similar Messages

Maybe you are looking for