E1200 v1. IPTV (multicast) is not working

sorry my english.
I have e1200 v1 with last firmware 1.0.03. Device using as AP/switch (no WAN port installed). When I open the TV chanal (239.0.1.3) the pictures 1 sec good and then stoped, device not responding. When TV off, 3 sec later internet works and device up.

If I am not mistaken, you are using your router as a switch or a pass though device, right? If that is the case then there should be a continuous traffic of the packets coming from your main router since the E1200 is just a plain switch and the E1200 will no longer filter the packets passing through. What you can do as of the meantime is to reset the router since the firmware has already been upgraded. Once the router has been reset and reconfigured then you need to observe the performance of the router. If there’s a discrepancy with the router’s performance then there’s a possibility that the router is not working properly and such you can return that router and have it replaced.

Similar Messages

Multicast Does not work between different VLANS

Hi,
I have problems with multicast. On the same VLAN i can see the SAP announcement in VLC and play, but on different VLAN i can see SAP but i cant play it. The play turn to pause and the video doesn´t appear.
I have 2 Cisco 6500 switch CORE with GLBP configured but not working. In the second switch i have all interfaces in shutdown. The first core switch have L3 routing enable.
The Global configurations:
ip multicast-routing.
I have the transmitter PC on vlan 51 i transmit to 230.0.0.50 group an im trying to recive on vlan 80. The vlans configurations are:
Vlan 51
ip address x.x.31.254 255.255.255.0
ip pim sparse-dense-mode
Vlan 80
ip address x.x.80.1 255.255.255.0
ip pim sparse-dense-mode
I have 2 Cisco 2960 (L2 only) for the access.
The principal commands outputs are:
CORE1#show ip mroute | inc 230.0.0.50
(*, 230.0.0.50), 01:50:50/00:02:21, RP 0.0.0.0, flags: DC
CORE1#
CORE 1
interface Vlan1
ip address x.x.1.1 255.255.0.0
ip access-group 101 out
no ip unreachables
ip pim sparse-dense-mode
mls rp ip
interface Vlan51
ip address x.x.31.254 255.255.255.0
ip access-group 151 out
ip helper-address x.x.x.x
ip helper-address x.x.x.x
no ip unreachables
ip pim sparse-dense-mode
mls rp ip
interface Vlan80
ip address x.x.80.1 255.255.255.0
ip access-group 150 out
no ip unreachables
ip pim sparse-dense-mode
glbp 80 ip x.x.80.254
glbp 80 timers 5 18
glbp 80 timers redirect 600 7200
glbp 80 priority 254
glbp 80 preempt delay minimum 60
glbp 80 authentication text glbpkey
glbp 80 forwarder preempt delay minimum 60
CORE2
interface Vlan1
ip address x.x.1.4 255.255.0.0
ip access-group 101 out
no ip unreachables
ip pim sparse-dense-mode
mls rp ip
interface Vlan51
ip address x.x.31.2 255.255.255.0
ip access-group 151 out
ip helper-address x.x.x.x
ip helper-address x.x.x.x
no ip unreachables
ip pim sparse-dense-mode
shutdown
mls rp ip
glbp 51 ip x.x.31.254
glbp 51 timers 5 18
glbp 51 timers redirect 600 7200
glbp 51 preempt delay minimum 60
glbp 51 authentication text glbpkey
glbp 51 forwarder preempt delay minimum 60
interface Vlan80
ip address x.x.80.2 255.255.255.0
ip access-group 150 out
no ip unreachables
ip pim sparse-dense-mode
shutdown
mls rp ip
glbp 80 ip x.x.80.254
glbp 80 timers 5 18
glbp 80 timers redirect 600 7200
glbp 80 preempt delay minimum 60
glbp 80 authentication text glbpkey
glbp 80 forwarder preempt delay minimum 60
end
Someone can help?
Thanks,
Alfredo

Hi johnd...
Im using VLC 1.1.2 (i can not update because i have a DVDT2 card to capture the digital terrestrial television and it only work in this version). I have all the firewalls down.
This is the output for the show ip igmp snooping groups on the 2960.
80 230.0.0.50 igmp v2 Gi1/0/21, Gi1/0/24
Port G1/0/21 is where the receiver is conected and the 24port is the trunk.
Jon, i revert and this is the output. I put the ip pim rp-address the same of the lookpback that i create previously.
(*, 230.0.0.50), 00:37:46/00:02:19, RP 192.168.230.230, flags: SJC
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
Vlan80, Forward/Dense, 00:09:52/00:00:00
The strange thing is that I have more than 40 vlans and it only fail in some vlans like 80.

Multicast configurator not working

I need help with multicast on Adobe Media Server 5. When I try to open configurator.html, all i get is the dark gray background.
Im running it from a mapped drive on a Win7 machine. If I do the same thing on another Flash Media Server 4.5, it's fine.
Any Ideas?
Thanks

- I’m on window7 with A: mapped to \\ams-server\c:\Program Files\Adobe
- Per your instructions I added A: as a Trusted location inthe Flash Player Global settings.
- Now I get a grey flash looking progress bar and another grey bar with “Error #2032”
Another important fact is the my computer is not connected to the internet. That appears to matter. Do the configurators require an internet connection?
I am able to recreate the Error #2302 issue on other computers that are not internet connected. Then, when I connect to the internet, the configurator seems to work.
Here is the test I ran
1. Installed AMS 5 on a laptop while not on the internet. It plays the flash stream demo fine.
2. I attempted to open f4mconfig.html and it did not work. Grey screen, so I added c: to my trusted locations and then I get the Grey bar with Error #2302.
3. I connected the laptop to the internet.
4. I reloaded f4mconfig.html and it worked fine.
5. I disconnected from the internet.
6. I then tried to open the multicast configurator.html and I get the Grey bar with Error #2302
7. I confirmed taht f4mconfig.html still works while disconnected from the internet.
Packet captures show that a working f4mconfig.html is doing HTTP GET of these files
/images/shared/download_buttons/get_flash_player.gif
/pub/swz/flex/4.6.0.23201/framework_4.6.0.23201.swz
/pub/swz/flex/crosdomain.xml
/crossdomain.xml
/pub/swz/tlf/s0.0.232/textlayout_2.0.0.232.swz
etc

Linksys e1200 PORT RANGE FORWARDING is not working

I currently have an E1200. I can port forward single ports, but when I attempt to forward a range of ports it doesn't work and there is no error in the log.
Specifically I am port forwarding RTP ports (10000 - 20000). I am aware of the security risks, please do not preach.

I have a problem with port forwarding http port 80 this for i surveillance camera.
I have all the settings are correct but I can not convert. Opening this port Also no other ports open. Who can help me on the way to this is to get together. I mtu gezte the firewall function in 1400 and put on the standard port 80 http to put. and of course the ip address that is in the same range.
I do not know what I'm doing wrong because the old linksys just worked. It I hope someone can help me.

Multicast in not working with RTMFP

When using RTMFP multicast is working , iam able to see in router , but when viewing stream at remote end on satellite TCP packet are generating instead of UDP .
Scenario :
Using Encoder with RTMP ---then Media server with Fusion RTMFP--- then Router for multcasting ---Remote end Router---HUB Satellite ---Remote Satellite ---remote End computer on which using multicast player---

The line input on the mini requires a 'line-level' signal, so the only microphones that work are ones that have an amplified output. Standard mics don't generate enough voltage to drive the mini's amplifiers.
That's the reason the mics work with the Griffin device (it has an amplifier) but not the mini directly.

Home sharing sporadically not working, fixed by O2 router multicast setting

I've been scratching my head for months about why my Home Sharing was only working sporadically on my home network. Each time it failed the only thing that would sort it out was to reboot my router (an O2 Wireless III router) - a bit of a pain, to say the least.
After trawling round lots of forums yet again, I came across a post in the O2 forums about the wireless "multicast" setting not working properly on the O2 IV router (i.e. when ticked it's actually off, and when unticked it's actually on): http://forum.o2.co.uk/viewtopic.php?p=347348#p347348 So even though I have an O2 III wireless router I thought it was worth a go and changed the setting (log into the admin of the router, click Home Network in the left menu, then click WLAN:YourNetworkName on the right, then Configure at the top right, and the checkbox is next to "Allow multicast from Broadband Network") and hey presto! The Home Sharing from my iTunes libraries immediately popped up and stayed on!
So if you have sporadic problems with Home Sharing and you're on an O2 box, try this. If you're not on an O2 box but you have the same symptoms, try digging around for a "multicast" setting - that may be where the problem lies.

I couldn't find the Multicast config option on my O2 Wireless Box III so I opted for reloading the router and it did the trick this time.
In the past I also had to spend quite a few number of cycles troubleshooting sporadic connectivity issues and it turned out to be that the O2 Wireless Box III and AppleTV 2 don't connect well via 802.11n, the connection is very unstable and rather you have to downgrade the speed to 802.11g and everything works fine. As soon as you downgrade and restart the ATV then all devices are visible.

WRT610N v2 (fw b5) Multicast (IPTV) not work

Hi!
See subj. When I disabling filtering of multicast in security page of official firmware and press save button, IPTV sometime work on wi-fi and lan channels, but, when I trying to change TV channel all work of router holds about for 3-5 minutes. I think, that this option (disable multicast filtering) does not work. Router have a very high price in our country, my previos D-Link DIR655 work fine in all same situations, but its price is lower about half of Cisco device. When you can do a normal version of firmware for WRT610N v2? My mind about CISCO production was some higher...

что за сервис?!!! и это брэнд???
I'm awaiting for answers from cisco technicians... When you can make a useful firmware for WRT610N v2 router with working multicast option?

E1200 - Ports not working and mac filtering problem

If there was a way to give negative stars to this router, I would. As it is, the minimum rating I can give this product is one star, and that's one star too many.
I was upgrading from the WRT54G, which is an ugly thing to look at, but a reliable workhorse nonetheless. I turned that in to a downstream switch in my comms hub.
On the E1200, I flashed the latest firmware, used different Cat5 cables, and different laptops before committing to hating this product.
The first time I reached out to Amazon, the Amazon rep gave me a Cisco number to call. Turns out, that's some shady mortgage refinance hotline. Try it for yourself! 1-800-666-1771.
Now, the rant -
1. Two out of four wired LAN ports don't work: What can be the fix for this?! The activity lights on ports 3 and 4 blink and suggest data transfer is taking place, but the wired laptop simply can't acquire an IP address and access the internet. Same result when I connect my Panasonic Blu-Ray player to ports 3 and 4. None of the Viera Cast features load.
2. MAC filtering unreliable: The wireless routing works somewhat reliably, if and only if, one settles for the most basic security. If I only choose a password and WPA2 protocol, things work fine. If I add another layer of security (in my case, enabling MAC filtering and only PERMITTING gateway to listed MAC IDs), things break down. As soon as I disable MAC filtering, wireless access to authenticated clients is restored.
3. Cisco customer service: The censored world we live in, compels me to criticize politely. TERRIBLE. Cisco website is unintuitive, and frustrating. There's no easy way to register your purchased product. The Cisco "registration" is intentionally misleading and deceptive. For all intents and purposes, it's just an information gathering tool for Cisco. Don't bother registering there, unless you love the idea of storing your personal information on their servers. Their phone-based customer service is apathetic and uninterested. My rep was so distrusting of my intelligence and motor control, that he simply wouldn't believe that I had selected "PERMIT" and not "PREVENT" as the option under MAC filtering. After he asked me the same question for the fourth time, I raised my voice, and he gave up the idea of checking for the fifth time.
However, this review is a tale of two companies. I reached out to Amazon again. This time, I got a rockstar in the shape of Leanne C! She was incredibly helpful, and understanding. What's more, she set up my return without any hassle and this Cisco dud is on its way back. I'm a big fan of Leanne's and my confidence in Amazon is restored.
I'm sure that i received a lemon. I've never had problems with Linksys products. Maybe others' experience is different from mine.

In your case as port numbers 1 and 2 does not work, what you could have done a loop back test. To perform a loop back test you need to take an ethernet cable, connect one end of that cable to internet port and the other end to the non-working port on the router. If you get the led to glow on both internet and the respective ethernet port that indicates that the port is working fine.
It could also be a sychronization issue between the above mentioned lan ports and the lan card of your computer. As a part of trouble shooting you can try to reduce the card speed of your lan card. Following are the steps to reduce the speed of your lan card.
START--> right-click My Network Places and click Properties
right-click on the device manager and click properties
Click on the CONFIGURE button
Select the ADVANCED tab and in the box under the header property select "speed and duplex" and change the value on the right to 10 mbps half duplex. A restart would be recommended after performing these steps.
In the second half you said that after enabling the mac filter option the internet breaks down. Here, do you mean to say that the computer
gets disconnected from the wireless network or it stays connected with a valid IP address but without an internet connection.
Well, it is an unusual issue however you could have reset and reconfigure the router as you got the latest firmware upgraded on it.
Steps to reset the router:
Push the reset button on router for 30 seconds, turn off the router wait for 30 seconds and then power it on. Power light should blink when you perform the reset process.

Multicast rtmp - rtmfp republish does not work (always new netgroup)

publish an multicast video stream with fmle 3.2
start the multicast stream - stop - start
fml should use the old netgroup
log file
http://paste.railsbox.eu/show/669/

Hi John,
Thank you for your reply. Better late than never! Am glad I
got a response :-)
It does indeed sound like a caching pb on the server and that
was my initial request the net admins. Unfortunately did not work.
In the meantime I made my case to the net admins that I needed
admin rights to the Roboengine in order to succesully reach my job
objectives and after a some time they accepted :-).
I looked closer and really could not figure out what the pb
was: all the new files were physically there but the TOC, index and
CSH does not update. Accessing the project locally rendered the
same pb.
My only solution was to delete and republish. Worked fine.
Perhaps somebody could test this behaviour in a different
environment and see what they get?
Steps to reproduce:
1°) Create an RH project (e.g. Project1.XPJ), create
TOC, index and CSH and publish to the server using a name (e.g.
Project).
2°) Create another RH project (e.g. Project2.XPJ) create
TOC, index and CSH (different to the first one) and publish to the
server using the name as the initial project (i.e Project).
- Chris.

Multicast not working SCCM 2012 SP1

Hi,
Am having issues getting multicast working with SCCM 2012 SP1 / Server 2008 R2.
We have followed all the guidelines in this forum but still no joy
- Multicast setting enabled on DP
- Multicast Enabled on OS Image
- Task Sequence set to down content when needed
- SCCM DP and Client are on same VLAN to rule out routing issues
- Network team confirm all ok there end anyway
- Boot images / WDS and PXE are all healthy
The PC Boots via PXE ok and runs our windows 7 task sequence, when the task sequence starts it says "Opening multicast session" for about 5 seconds and then disappears. Its as though it tries but then fails. Unicast works fine.
I then set the OS image to "Only use Multicast" which produces the following error in the client SMSTS.log
reply has no message header marker
Failed to open session request (Code 0x80004005)
ApplyOperatingSystem 28/01/2014 12:53:25
1944 (0x0798)
ClientRequestToMCS::DoRequest failed. error = (0x80004005).
ApplyOperatingSystem 28/01/2014 12:53:25
1944 (0x0798)
Request to MCS 'SererName' failed with error (Code 0x80004005).
ApplyOperatingSystem 28/01/2014 12:53:25
1944 (0x0798)
Multicast OpenSessionRequest failed (0x80004005).
ApplyOperatingSystem 28/01/2014 12:53:25
1944 (0x0798)
Sending status message: SMS_OSDeployment_PackageDownloadMulticastStatusFail
ApplyOperatingSystem 28/01/2014 12:53:25
1944 (0x0798)
Any idea on how we get this working ?
Thanks

The logs related to multicast that you'll see on the site server are:
mcsisapi.log
Records information for multicast package transfer and client request responses.
Site system server
mcsprv.log
Records multicast provider interaction with Windows Deployment Services (WDS).
Site system server
MCSSetup.log
Records details about multicast server role installation.
Site system server
MCSMSI.log
Records details about multicast server role installation.
Site system server
Mcsperf.log
Records details about multicast performance counter updates.
Site system server
http://technet.microsoft.com/en-us/library/hh427342.aspx
>> Network team confirm all ok there
end anyway
This is something to double and triple check. If Multicast is not enabled on the routers/switches properly, this will not work. If there is a firewall between the client and the distribution point that doesn't have the Multicast ports open, this
will not work.
Client -- > Distribution Point Configured for Multicast
Description
UDP
TCP
Server Message Block (SMB)
445
Multicast Protocol
63000-64000
http://technet.microsoft.com/en-us/library/hh427328.aspx
I hope that helps,
Nash
Nash Pherson, Senior Systems Consultant
Now Micro -
My Blog Posts
If you've found a bug or want the product worked differently,
share your feedback.
<-- If this post was helpful, please click "Vote as Helpful".

Jrockit multicast bug on RHEL4, WLS cluster does not works!

OS and Kernel Version: Linux achilles1 2.6.9-34.0.1.ELsmp #1 SMP Wed May 17 16:59:36 EDT 2006 x86_64 x86_64 x86_64 GNU/Linux
We use Bea Weblogic 8.1SP5 with Jrockit JVM 1.4.2 on RHEL3. We upgraded to operating system to RHEL4, and found that the interface binding for multicast communication does not bind to the correct interface, it is always using the default interface. We tried it from a sample program, and found that the error is in the JVM.
This is a critical error for us, because our application server cluster use multicast for cluster communication.
No error msg. It seems like this BUG:
http://bugs.sun.com/bugdatabase/view_bug.do?bug_id=4082533 but it is solved.
List steps to reproduce the problem:
socket = new MulticastSocket(i);
if(s2 != null)
try
InetAddress inetaddress = InetAddress.getByName(s2);
System.out.println("Using interface at " + inetaddress.getHostAddress());
socket.setInterface(inetaddress);
System.out.println(socket.getInterface());
catch(SocketException socketexception)
throw socketexception;
}

Helo,
You can reproduce it by this way (we have 6 RHEL4 servers, problem is the same). We tried with programs written in C (mcast,Tibco), multicast perfectly works on all interfaces on all servers. But in Java:
Server:
[wlxapp@webex3]$ uname -a
Linux webex3 2.6.9-34.0.1.ELsmp #1 SMP Wed May 17 17:05:24 EDT 2006 i686 i686 i386 GNU/Linux
Problem - with Bea mukticast tester (or any Java class), using the nondefault webex3-priv interface(eth1):
[wlxapp@webex3]$ java -cp wl9.jar utils.MulticastTest -N webex3_priv -I webex3_priv -A 224.1.1.11 Starting test. Hit any key to abort Using interface at 192.168.1.1 Using multicast address 224.1.1.11:7001 Will send messages under the name webex3_priv every 2 seconds Will print warning every 600 seconds if no messages are received
I (webex3_priv) sent message num 1
I (webex3_priv) sent message num 2
I (webex3_priv) sent message num 3
Did not receive any message.
But if we use the default webex3 interface (eth0)
[wlxapp@webex3]$ java -cp wl9.jar utils.MulticastTest -N webex3 -I webex3 -A 224.1.1.11 Starting test. Hit any key to abort Using interface at 10.4.20.4 Using multicast address 224.1.1.11:7001 Will send messages under the name webex3 every 2 seconds Will print warning every 600 seconds if no messages are received
I (webex3) sent message num 1
I (webex3) sent message num 2 Received message 2 from webex3
I (webex3) sent message num 3 Received message 3 from webex3
Works perfectly.
TCPDUMP:Messages are out from server(other srv also see it), so we have problems probably with receiving them:
[root@webex3]# tcpdump -i eth1
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth1, link-type EN10MB (Ethernet), capture size 96 bytes
11:42:56.647362 IP webex3_priv.idmz.t-mobile.intra.afs3-callback > 224.1.1.111.afs3-callback: rx type 95 (1472)
11:42:56.648168 IP webex3_priv.idmz.t-mobile.intra > 224.1.1.111: udp
11:42:56.648245 IP webex3_priv.idmz.t-mobile.intra > 224.1.1.111: udp
We examined the lsof output, the tester bind to all interfaces, so it should receive the messages:
[wlxapp@webex3]$ /usr/sbin/lsof -p 11127
gij 11127 wlxapp 8u IPv4 150320 UDP *:afs3-callback
We tried the test with Java 1.4.2 and 1.5 (Jrockit and Sun), the results are the same.
You can easily reproduce the problem with an RHEL4 server with 2 network interface.
Our real problem that if multicast have problems, our Weblogic clusters does not works.

E1200 not working after factory defaults

After getting a E1200 router a few years ago i have reset the router many times, but during my most recent reset the internet only works on the computer that i set up the wireless from in the first place. it seems that the only computer that i cannot access 192.168.1.1 is the computer that the wireless works on. everytime i try to access the setup page on either my phone or another computer a note pops up and tells me that if i access this page internet may not work on my computer. i have tried everything that i could in the settings but nothing seems to work can someone help?

Hi david,
Check this link for steps on how to configure the router properly.

E1200 router not working -- Error 3005 (and manual network not connecting)

I'm trying to set up a new E1200 N300 Monitor, and am not having any luck. Using the Cisco Connect program ends in an error during the "Validating connection" step every time, telling me:
Error: 3005
An HNAP call to the device failed because the HTTP connection was broken.
(If it's relevant, the serioal number, connection type, and IP address (WAN) all come up as "unknown" in the error details).
I am able to set up the router manually via the web browser access. I can name the wifi network, set up the security, and even see and authenticate to the network from my devices, however, no internet connection is available when connected. (The internet connection itself is good -- when I move the incoming cable from the router to the computer, I instantly have perfect access -- thus this post)
I've also tried all the basic steps of reset and restarting everything involved multiple times, but I always end with the same result -- 3005 error in the setup app, and then a manually-configured wifi network that appears to be working and can authenticate devices, but does not provide any internet connection.
I'm at a loss at this point -- does anyone here have any advice? Thanks a lot for your time and input.
-e.
Solved!
Go to Solution.

What type of internet connection do you have?
Example:
PPPoe
Cable Modem
ADSL
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

E1200 Router Suddenly Not Working

I have had this router for only little over a month and suddenly it stops working. I am not talking about some problem that could be fixed just by turning it on and off, I've tried that and the internet still would not work. It is defintely the router that isn't working because the internet works when connected directly to the modem. Does anyone know what can be wrong?
Thank you!

Did you encounter an internet or power outage before it stopped working? Perhaps the settings on your modem is no longer synchronized with your router. I suggest you manually reset and reconfigure the router.
There are two ways to reset the E1200 to its factory defaults. Either press and hold the Reset button for approximately five seconds, or restore the defaults from the Administration > Factory Defaults page on the router's web-based setup page. Once done, you can now go ahead and setup the router. You may also find this helpful: http://kb.linksys.com/Linksys/ukp.aspx?pid=80&vw=1&articleid=24153

UCCX 7: Network MoH ringback not working with Multicast MoH.

Hi All,
I have a CUCM and UCCX installed in a Data Centre serving a site across a WAN, on the site there are agents using CAD and a backup SRST router, unicast MoH was streamed across the WAN from CUCM in G729 format and network MoH (ringback.wav file) from the CTI ports to give ringback to calls been transferred to agents in the call centre.
To conserve BW and have better quality MoH, Multicast MoH was configured to stream the User MoH from the routers flash instead of a G729 unicast stream across the WAN. To get Multicast MoH to work I had to change the MoH streaming codec from G729 to G711u on the CUCM. This enables the CUCM to get signal to the phones to join the Multicast stream on the SRST router when a call is placed on hold but as this is a cluster parameter it stopped the ringback MoH on the CTI ports resulting in no ringback when callers are been transferred to the agents in the contact centre. Is there any way I can get the script to play the ringback.wav file when transferring calls to agents or get the call manager to stream the ringback across the WAN while Multicast MoH is implemented?
Any help or ideas would be really appreciated
Thanks
Neil

Hi,
When the call is ringing on the agents phone CUCM should be sending the appropriate commands to the endpoints to join whatever multicast stream you have configured for network hold. The issue is that no multicast stream is available on that IP address/port number combination. (I assume that you have set the SRST MoH parameters to match what is sent for user hold).
SRST versions up to 7.x only support one MoH stream. However SRST 8.0 has extended this to five streams so I think this could be a solution to your problem. Check out the document below.
http://www.cisco.com/en/US/partner/docs/voice_ip_comm/cusrst/feature/guide/MOH_srst.html
You will need IOS Release 15.0(1)XA to support this feature.
An alternative would be to stream the MoH from another multicast source. This could be a PC running VLC if things were tight.
Please let us know how you get on.

E1200 v1. IPTV (multicast) is not working

Similar Messages

Maybe you are looking for