E1200 wireless works great, but needing another wireless router to hardwire connect to AVR

I have an e1200 Linksys router hooked up and working well, a wired connection to my first computer a wireless connection to my second (laptop) in the basemen and to my HDTV. My question is what Linksys device would I need to enable me to get a wireless connection in the basement to then hardwire connections to my Blue-Ray player and my HK AVR-3650. Any advise would be a great help as in I have no clue on what I need, but again I would like to somehow take a wireless signal from one wireless router to another to then have wired connections from both wireless routers. Also, was the e1200 not the right router or can I still make something out of it? Thanks in advance - Ohio

Aside from powerline adapters, you may consider as well WES610N. It is a wireless switch that you can connect to your home/main router to extend your existing network wired and wirelessly. It has 4 ethernet ports on the back for you to connect your wired devices to your network. For more information about this device, refer to these links: Expanding your home network using a WES610N Dual-Band N Entertainment Bridge, Linksys WES610N Frequently Asked Questions.

Similar Messages

WRT160N V2: wireless works great, but wired intermittent and slow

Getting very good connection and speed in wireless. But when I connect the ethernet cable, the speed slows down and half the time I get "cannot connect" error messages. I bought this router in Oct 2009 and so don't know if it needs a firmware update. Based on other posts, I went to IE - Tools - Internet Options - Connections - LAN Settings and unclicked the only thing that was clicked: Automatically Detect Settings. That did not seem to make any difference. Yesterday, based on some advice on some other site, I switched ports on the router and it worked very well for a while. But today, no port really performs.
Solved!
Go to Solution.

Try to upgrade/re-flash the firmware on your router.
Connect the computer with the Ethernet cable to the router.
Download the latest firmware from Linksys website and save it on your computer. Open the setup page of the router. Click on Administration tab and go to Firmware upgrade sub tab. Browse the firmware file that you have already downloaded and upgrade it on your router.
After upgrading the firmware on the router, it is recommended that you should reset the router and reconfigure it. Press and hold the reset button on the router for 30 seconds. Release the reset button and wait for 30 seconds. Power cycle the router and reconfigure it.

'group by' works good, but need another column

Hi,
I am seeking for better construction for next issue, this code is not good-readable and seems I can't add another column to returned output:
;WITH q AS (
SELECT srvs.description as srv, apps.description as app
FROM srv_link_app as link LEFT JOIN servers as srvs
ON link.srv = srvs.id
LEFT JOIN apps
ON link.app = apps.id
SELECT
FROM (
SELECT DISTINCT app
FROM q
) qo CROSS APPLY
SELECT CASE ROW_NUMBER() OVER(ORDER BY srv) WHEN 1 THEN '' ELSE '; ' END + qi.srv
FROM q qi
WHERE qi.app = qo.app
ORDER BY
srv
FOR XML PATH ('')
) qi(srv)
Works perfect, It connects 3 tables: apps, servers, link and groupy by column servers. So,
link table is auxiliary connection.
Output is:
app1 | server1;server3
app16 | server6;server13
It's good but I need add another column app.long_info, for example (Output):
app1|srv1;srv2;srv5 | app.long_info here

Can you post DDL? What little you showed us is a mess. You have a magic generic “description” that transform from servers to applications in violation of ISO-11179 Standards, logic and data modeling. Likewise, you have the classic noob “id” that also morphs
from servers to applications. I will bet it can be a squid or an automobile, too!
>> So, link_table is auxiliary connection. <<
Auxiliary connections?? I never head that term before and I think been around SQL for awhile :). The term “link” comes from 1970's network databases. It was a type of pointer structure. Pointers connect, references do not. We would never use it in RDBMS. We
have n:m, 1:m or n:1 relationships and the relationships have real names. Using OUTER JOINs makes no sense.
Next, I see you hate Dr. Codd and First Normal Form (1NF). You use XML to make the code hard to port, hard to maintain an unpredictable. Good SQL programmers write and do not do display formatting in the query. This is the principle of any tiered architecture,
not just SQL.
Here is my guess, with clean up:
CREATE TABLE Applications
(app_id CHAR(12) NOT NULL PRIMARY KEY,
app_description VARCHAR(25) NOT NULL,
CREATE TABLE Servers
(server_id CHAR(12) NOT NULL PRIMARY KEY,
server_description VARCHAR(25) NOT NULL,
CREATE TABLE Application_Assignments
(app_id CHAR(12) NOT NULL
REFERENCES Applications
ON DELETE CASCADE
ON UPDATE CASCADE,
server_id CHAR(12) NOT NULL
REFERENCES Servers
ON DELETE CASCADE
ON UPDATE CASCADE,
PRIMARY KEY (app_id, server_id),
Since we have no sample data, no sample output, we can only guess. But your terms an approach are completely wrong. Have read any book on data modeling or RDBMS?
--CELKO-- Books in Celko Series for Morgan-Kaufmann Publishing: Analytics and OLAP in SQL / Data and Databases: Concepts in Practice Data / Measurements and Standards in SQL SQL for Smarties / SQL Programming Style / SQL Puzzles and Answers / Thinking
in Sets / Trees and Hierarchies in SQL

HT3728 I do not need another wireless network but want to use the airport express for printer access only. Can this be done and how?

I do not need another wireless network but want to use the airport express for printer access only. Can this be done and how?

You can configure the AirPort Expess to "Join a wireless network" and enable the Ethernet port so that Ethernet devices will be able to connect.
In order to print from the iOS devices, you will need to have an application like Printopia installed on your Mac. The Mac must be active when you want to print.
More details here: Printopia - AirPrint to Any Printer - Print from iPad - Print from iPhone ...
There is a free trial available for Printopia, so make sure that it will work before you buy the AirPort Express.

When running lion 32bit my wireless works great, when I run lion in 64 bit the wireless works awful. Any ideas?

When running lion 32bit my wireless works great, when I run lion in 64 bit the wireless works awful. Any ideas?

I solved my own problem. Found spotlight in Lion 7 doesn't seem to like third party external drives and gets hung up and unmounts the drives. Had to go into the spotlight preferences and choose all my external drives to not be searched by spotlight.
Temporary fix but would love to see apple address this issue in the next version of Lion.

Any suggestions on how to get wifi to work? I have a multitech router and can connect with a computer wirelessly but not the ipad.

Any suggestions on how to get wifi to work? I have a multitech router and can connect with a computer wirelessly but not the ipad.

iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/TS1398

I bought a iphone 4s of ebay it works great but i want to use the passcode but can't because he can't remember what he put it as

i bought an iphone 4s of ebay and it works great but i went to set up a passcode but the person who had it before has put one on there and he can't remember what it is, is there anyway of resetting it

If You Are Locked Out Or Have Forgotten Your Passcode
iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
iOS- Understanding passcodes
A Complete Guide to Recover Your iDevice if You Forget Your Passcode
If you cannot remember the passcode, you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and resync the data from the device (or restore from a backup). If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present. Refer to Updating and restoring iPhone, iPad and iPod touch software.
Try restoring the iOS device if backing up and erasing all content and settings doesn't resolve the issue. Using iTunes to restore iOS devices is part of standard isolation troubleshooting. Restoring your device will delete all data and content, including songs, videos, contacts, photos, and calendar information, and will restore all settings to their factory condition.
Before restoring your iOS device, Apple recommends that you either sync with iTunes to transfer any purchases you have made, or back up new data (data acquired after your last sync). If you have movie rentals on the device, see iTunes Store movie rental usage rights in the United States before restoring.
Follow these steps to restore your device:
     1. Verify that you are using the latest version of iTunes before attempting to update.
     2. Connect your device to your computer.
     3. Select your iPhone, iPad, or iPod touch when it appears in iTunes under Devices.
     4. Select the Summary tab.
     5. Select the Restore option.
     6. When prompted to back up your settings before restoring, select the Back Up
         option (see in the image below). If you have just backed up the device, it is not
         necessary to create another.
     7. Select the Restore option when iTunes prompts you (as long as you've backed up,
         you should not have to worry about restoring your iOS device).
     8. When the restore process has completed, the device restarts and displays the Apple
         logo while starting up:
           After a restore, the iOS device displays the "Connect to iTunes" screen. For updating
          to iOS 5 or later, follow the steps in the iOS Setup Assistant. For earlier versions of
          iOS, keep your device connected until the "Connect to iTunes" screen goes away or
          you see "iPhone is activated."
     9. The final step is to restore your device from a previous backup.
If you can not restore your device then you will need to go to recovery mode.
Placing your device into recovery mode:
Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
     1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the other end
         of the cable connected to your computer's USB port.
     2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the
         red slider appears, then slide the slider. Wait for the device to turn off.
          If you cannot turn off the device using the slider, press and hold the Sleep/Wake
          and Home buttons at the same time. When the device turns off, release the Sleep/Wake
          and Home buttons.
     3. While pressing and holding the Home button, reconnect the USB cable to the device.
         The device should turn on. Note: If you see the screen pictured below, let the device
         charge for at least ten minutes to ensure that the battery has some charge, and then
         start with step 2 again.
     4. Continue holding the Home button until you see the "Connect to iTunes" screen.
         When this screen appears you can release the Home button.
     5. If necessary, open iTunes. You should see the following "recovery mode" alert:
     6. Use iTunes to restore the device.
If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
Additional Information:
Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information.

I cannot send an email from my iPad 2? No problem receiving, why does this happen? Have tried the suggestions for setting up email and after doing the sync mail through iTunes receiving worked great but still cannot send? Any help would be great

I cannot send an email from my iPad 2? No problem receiving, why does this happen? Have tried the suggestions for setting up email and after doing the sync mail through iTunes receiving worked great but still cannot send? Any help would be great!

The fact that you can receive means you have a valid e mail address, and have established the connection to the incoming server, so all of that works. Since the send does not work, that means your outgoing server is rejecting whatever settings you used formthe outgoing set up. Try them again.
Google your particular isp, and ipad and many times you will find the exact settings needed for your isp. Or tell us here, and soneone else may be on the same isp. Some mail services need you to change a port, or have a unique name for the outgoing server.
Kep trying.

My printer works great but I keep getting error messages from HP Solutions Center

I'm using an HP Officejet J6480 All in One Printer on a Windows 7 64 Bit machine. The printer works great but I kept getting error messages from the HP Solutions Center every 15 seconds that popped up making it impossible to do work on my laptop so I uninstalled the Solutions Center to try to fix the problem. Now the printer won't print. Is there a way to re-install the Solutions Center and get rid of the pop up error messages?

hello Danagriz, unfortunately the plugin check page lags behind. adobe has released a critical patch for a vulnerability in its flash plugin, which is reportedly already exploited in the wild. therefore firefox will block insecure versions from running by default on websites for your protection.
https://helpx.adobe.com/security/products/flash-player/apsb14-27.html https://addons.mozilla.org/firefox/blocked/p794
please update to Adobe Flash Player version 16.0.0.235 as soon as possible, which you can download from http://www.adobe.com/products/flashplayer/distribution3.html (use the windows-exe for plugin-based browsers).
in order to update java, go to java.com (or if you don't need the plugin you can also uninstall it though the windows control panel)

Could you help me with an app situation? We purchased several codes for Splashtop to install on our iPad 2's. It was working great but now that we upgraded the OS they have disappeared. The codes that we purchased are giving us an error that they have alr

Could you help me with an app situation? We purchased several codes for Splashtop to install on our iPad 2's. It was working great but now that we upgraded the OS they have disappeared. The codes that we purchased are giving us an error that they have already been used. So far it has only been 2 iPads.
Any solutions?

The compiler is highlighting the areas you got wrong, although the error messages are somewhat confusing.
Error 1: NSLog is a function and needs to be called as such, see e.g. the circleArea call on the line above. Functions are called using the function-name with its arguments in paratheses e.g. foo(12, 13).
Error 2: looks like a typo, defining a function is done as function-name(... <arguments> ...) { ... <body> ...}. In your code there is a ";" between the arguments and the body that should not be there, you probably copy pasted it from the forward declaration at the top of the source codde file.

HT201272 I have tried several ways to transfer my itunes library and Playlists to a new computer. I get the music library but not the playlists. Can you advise? 2nd I purchased 21 new tunes yesterday on the new computer worked great but when I made a disc

I have tried several ways to transfer my itunes library and Playlists to a new computer. I get the music library but not the playlists. Can you advise?
2nd > I purchased 21 new tunes yesterday on the new computer> worked great> but when I made a disc to transfer the playlist. I get the music but no album info just 1,2,3,etc. So I have signup both computers to share thinking that would work. But no to that also.
Please advise.
Thanks,
Bob

Copy the entire /Music/iTunes/ folder from old computer to new computer.
See this -> http://support.apple.com/kb/HT4527

Phone works great but when on a call proximity sensor kicks in turns off the screen. When I pull the phone away from my head screen is still blank. The force hangup/lock is the only way to bring the screen back on

hi,
phone works great but when on a call proximity sensor kicks in turns off the screen. When I pull the phone away from my head screen is still blank. The force hangup/lock is the only way to bring the screen back on.
I purchaged it before one month onl. So i wont understand how it comes. Please help me. I am waiting for you reply.

"Your face is so ugly, it broke your phone!" Ha ha. Get it? How I was joking there? About your iPhone not working correctly after... <sigh>
But seriously, you said the situation only happens when you have been on a long call, so maybe the iPhone is just autolockng?

My Touch ID works great, but because I have been using it, I now can't remember my password

My Touch ID works great, but because I have been using it, I now can't remember my password.
How can I reset my password?

Hi Each day when you power up your iphone you have to use the 4 number passcode. How can you forget this in 1 day? Cheers brian

I used the location app to find my daughters ipod with my ipad mini. App worked great, but now I can't use my ipad, can't get rid of the alerte "ipod located". Now what do I do

I used the location app to find my daughters ipod with my ipad mini. App worked great, but now I can't use my ipad, can't get rid of the alerte "ipod located". Now what do I do

Try a reset:
Hold the Sleep and Home button down for about 10 second until you see the Apple logo.

HT1338 My G5 PowerPC still works great, but what is the latest OS that is possible. I just bought a new HP Printer and it is not compatible with OS 10.4. Is there any hope?

My G5 PowerPC still works great, but what is the latest OS that is possible. I just bought a new HP Printer and it is not compatible with OS 10.4. Is there any hope?

A PPC G5 cannot run any version of OS X beyond Leopard 10.5.8.
You should be able to find a Leopard retail (black) install disk on eBay. A grey update disk is machine specific and won't work.

E1200 wireless works great, but needing another wireless router to hardwire connect to AVR

Similar Messages

Maybe you are looking for