E1700 Advanced Routing - help needed

I am having trouble creating static routes through my Linksys E1700 (Rev v1, f/w 1.0.02. I keep getting errors on all routes I try to enter. Either I get a complain that a part of an IP adress is not in range 1-233 or I get the error message "Invalid route" when trying to save the route. Can anyone post what restrictions are enforced on the entered static routes? What I want to achieve is access to a separate ADSL modem that the router is attached to. That means that I have assigned the modem an IP adress that is not on the local network and need the router to pass this adress through the WAN port, but not to the ISP gateway. Something along the lines of: Local address of router and IP range used by DHCP in the router: 192.168.0.0/24Local address of ADSL modem: 192.168.1.1/24 I want to route: 192.168.1.1/32 through WLAN interface with gateway 0.0.0.0 Any ideas why the router does not allow me to do this? Also, if I could get any type of route through the E1700 WLAN interface I could assign my modem to match that (as long as it is not an IP address I need to use :-) ) But I have not been able to set up any route to the WLAN interface with gateway 0.0.0.0. /Nils

Similar Messages

Wireless Router Help Needed! Please and Thank You

My warrenty has expired on my router, and Linksys is conveniently not able to help me get my router back on track. I have had the same problem several times, and have had the steps wrote down to fix it however, I have recently moved into a new place and conveniently lost the paper.
Usually it was a matter of just cloning my mac ID and it would work, in which I tired that with no success! Im frustrated and I need my internet for my schooling.
If anyone could help me it would be GREAT! Im not able to be on the internet to check so often as to if I have a reply on here, so if you feel you can help please call me!
Thanks in advance!
Stephanie
(Mod note: Edited post for guideline compliance. Thanks!)
Message Edited by JOHNDOE_06 on 05-21-2009 08:29 AM

First Connect the Modem to the Linksys Router on the Internet Port and then connect your Computer to the Linksys Router on the Port no.1.
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
If your Internet Service Providor is Cable follow this link

Router Help Needed Badly!!!!!!!!!!

My nephew moved in to go to college and he needs to add his laptop to our wireless router. We have tried to have him set it up like I set up my laptop. It keeps telling him it is the incorrect password. I have even tried resetting to the default settings. Still nothing worked. Please, please help us. He is having to use a really weak network that has a lot of problems.

First of all you need to check the wireless settings (SSID and Security Key) of your Router.
Login to the Linksys Setup Page by typing 192.168.1.1 in the address bar...The default password is "admin" in the lower case.
Go to Wireless Tab and note down the SSID....Click on the subtab wireless security and note down your network key.
Now search for your network and connect it on the laptop.

Setting up HP L-7590 via usb to wireless router, help needed..!

Hi,
I have been using my L7590 via lan to a wireless router for a few years... that was perfrect...
Recently I had to change router because of change of ISP. The new router is a Huawei B683... the problem I have is that this router does not allow LAN connections from the router ...!! It does has a USB port that is for the printer...
I am unsure as to how I setup the printer connected via usb to the router....
Do I use the network installation setup...? Or do I use the USB setup...??
Any help is greatly appreciated...
Thanks

Hi,
Connecting the printer to a router's USB port (aka. print server) will only allow you basic print functionality , it won't provide you any scan functionality, faxing from the computer, ink levels or any operation of the HP Solution Center program.
To get full functionality you must work with the provided functionality which means USB connection directly to a single PC or Ethernet connection to a router.. therefore using an Ethernet router will be the preferred solution for you.
In order to setup the printer as you described you should connect the printer to the USB port and go to Control Panel > System. click add a printer and add it through the network.. there might be a need to enter your wireless homepage to enable the printer through the USB, there might be additional setup information in there.. that veries between different print servers and you may contact Huawei support or your ISP for any assistant within the print server configuration.
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Serious router help needed

hey all need some help here.
i got a msi rg54gs router hooked up with my ntl cable modem. In total there is two computers and a box connected to it via cables and a laptop via wireless.
i can access xbox live but cant join my friends games via my friend list. been told i need to open some ports so first question how i do that so it works. Secondly i may need to change the MTU how do i do that plz.
Anyone done this so it works with a xbox plz reply and help me. all help greatfully welcome thanx all

hey all need some help here.
i got a msi rg54gs router hooked up with my ntl cable modem. In total there is two computers and a box connected to it via cables and a laptop via wireless.
i can access xbox live but cant join my friends games via my friend list. been told i need to open some ports so first question how i do that so it works. Secondly i may need to change the MTU how do i do that plz.
Anyone done this so it works with a xbox plz reply and help me. all help greatfully welcome thanx all

Westell router - help needed

Hi, hope someone can help me with this westell router problem.
I have A90-750115 Vesalink router. My cable company set me with a static IP address. They told me to set my router to pull
static IP instead of dynamic IP from the modem. but the problem is I do nto know how to set the static IP on the router.
I checked online manual, but either I don't understand or it was not stated in the manual.
anyone knows how to set the static ip address on this router? or similar router in Vesalink line?
thanks

#1 I take it you have all of the settings, not just the Static IP.
Subnet Mask, Default Gateway and DNS Servers.
#2 If not, you need to get that first,
#3 I take it your cable modem is connected to the Uplink / E1 port of this Westell.
Source: http://www.westell.com/images/extranets/pdf/VersaLink_7500_User_Guide.pdf
on page 9 out of 186 pages.
#4 And I take it, you did not change the LAN IP of the Westell
#5 Go to 192.168.1.1 and log-in as need be to this Westell.
#6 If prompted to change the Default Password (page 32 to 34 out of 186 pages), do so.
#7 In the router go to Network Connections -> Versa Port.
#8 With Ethernet WAN Uplink Selected, change the connection type to Routed IP Address.
#9 Where it says, tunneling say disable.
#10 Then the next two option are:
a) Enable DHCP Client
OR to
b) Disable DHCP Client.
#11 Select Disable DHCP Client.
#12 Then enter in the Correct settings that you were given.
#13 Click on Apply
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

Captivate 4 advanced interaction help needed

I have a captivate 4 project that's due tomorrow for my new job and I can't figure out why it is not working correctly. I have spent the last 40 hours trouble shooting and have not been able to figure it out. Please help me out if you can. I have a 47 slide scenario that works right if you answer all the questions correctly. However, when you don't answer a question correctly the redirection is messed up even though it looks right in captivate 4. the back and forward buttons are not going where they should and at times you are advanced to another question without having answered the previous question. Here's the flash and captivate 4 files. I don't know what else to do and would greatly appreciate suggestions.
http://people.tamu.edu/~emmanuel.okafor/Quickr-final2.swf
http://people.tamu.edu/~emmanuel.okafor/Quickr-final2.cp

Hello,
Just had a quick look at your CP-file but opened it in CP5 so not totally sure: in the Quiz settings, you have only allowed 1 attempt for the Quiz (Quiz preferences, Pass or Fail) is that correct? You allow multiple attempts (2 or 3) in the individual questions, but this is normally meant to retake the question immediately. I had such an example on slide 18. Not sure, but please try to allow more than 1 attempt for the quiz itself.
Lilybiri

CP5 Advanced Action help needed for conditions....

Hi,
I have created my own MultipleChoice (MC) question with 4 answer possabilities whereof 3 are right and 1 is wrong.
As soon as a right/wrong answer is checked an advanced action is performed - checkmark in box shown and "feedback" to answer.
In case of a right answer - the feedback of any previous answer is hidden but the check mark of correct answers stay whereas the wrong answer checkmark is hidden.
An example of the advanced action for one of the three right answers:
This is what the question looks like before the answer of my question needs to be implemented:
Now to my question:
At the end of the answers I would like the user to get a message: CONGRATULATIONS.....
This should be displayed when all 3 right answers have been selected.
After that CONGRAT... message they can then click the Continue button to continue the training.
I am curious to any suggestion on how to realise this
Thanks in advance for the reply.
best regards
Stephanie

OPTION A:
Steps to achieve congratulations message on the same slide (which is the question) 1. Actions like B_Selected,C_Selected etc. have to be conditional actions instead of standard actions which they are right now.
2. Four variables are to be created from Project->Variables ->Add new. These can be named as a,b,c,d and set to 0(zero) which means the option is not selected 3. In the conditional action B_selected, first condition has to be something like
      If (1 equals 1)
            Show TC_Correct_B
            Show Image_230
            Hide Image_233
            Hide TC_Wrong_A
            Hide TC_Correct_C
            Hide TC_Correct_D
            Assign b = 1
4. In second condition of same action i.e. B_selected, do the following
      If (a equals 0 && b equals 1 && c equals 1 && d equals 1)
            Show TC_Congratulations
All the actions should have these two conditions and if there are actions like B_unselect, then 'Assign b = 0' in such actions.
OPTION B
On the other hand if it's fine to show the congratulations message on next slide, it will be simpler like this 1. Create the four variables a,b,c,d = 0 2. In actions like B_Selected (no need to change them to conditional action), add a statement 'Assign b = 1'
3. In actions like B_unselected, add a statement 'Assign b = 0'
4. On slide exit execute an advanced action which will be a conditional action as follows:
      If (a equals 0 && b equals 1 && c equals 1 && d equals 1)
            Go To Next Slide
      Else
            Jump to Slide __
5. On next slide write congratulations message.
Regards,
Vandana

Lynksys E900 Wireless-N300 Router - Help needed to share internet connection from PC to home network

Hi, I'm hoping someone can help me out with a problem I have:
I am currently connecting my PC to a mobile phone as a Wireless Access Point to give that PC access the internet. I also have a small home network, with one other PC and a Game Console. I own a Linksys E900 Wireless-N300 Router. My problem is this. How do I share that internet connection with the rest of the home network?
To the best of my knowledge its not possible to connect my mobile phone directly to my Linksys E900 Wireless-N300 Router, although if anyone has any ideas how to do this I'd love to hear!
So my alternative idea is to connect to the internet via one PC, set up that internet connection as "Shared." and then allow the other devices on the home network to connect thru this. My question is how do I set up my Linksys E900 Wireless-N300 Router to allow my other PC and game console connect to the internet? Bridge Mode? PPPoE? Any help or suggestions would be greatly appreciated! PS: both PC's are running on Windows 8

I have Cisco Linksys E900 router. I want to make my home Wi-Fi zone. But I don’t have Static IP. One more thing is that Service provider have web page Authentication. I have username and pass.
I am able to make SSID and security for my WI-FI LAN. I can use internet on one device. If I tried from second device again it’s asking me for username and password. While login it’s showing your first session in not logout. (Means I have to logout from 1st device and have to login on 2nd device.)
Is there any option that I can Use my all devices at same time?

ROUTER HELP NEEDED!

Me and my roommate both have laptops and we both want wireless internet. We bought the linksys WRT5G2. But it will only work if one of the computers is plugged into the router.. can someone please tell us how to make it work?

Hello,
I have a Dell Latitude laptop, with it came a ENPWI-S2 802.11g WIRELESS CardBus.
I have that pluged in and installed. The status on my computer is that im connected and have full signal strength, but still not connected to the internet. The Wireless router that I have is a Linksys Cisco WRT54G2 V1.5. I have no idea what to do I took it to a computer shop, and the internet worked there, but for some reason it wont work at my house. It's making me oh so very fustrated.
If anyone could help that would be great!!!
I would appreciate it alot.*

Outboard effect routing help needed

I am trying to route the output of a track to a Korg Kaoss Pad and then have that outboard effect routed back into a new track. Using a pre-recorded audio track, how do I route that track out (I was using the headphone jack of the Mac as the out [i.e. line in of the Kaoss] and then routing the out of the Kaoss to the instrument 1 input on my Apogee Duet). I can't figure out how to assign the headphone output as the input of the new track. Sorry if this is too confusing.

Midlake wrote:
I need the output of a recorded track to go into the Kaoss and the output of the Kaoss to be the input of a new audio track. The original track will remain unprocessed and a new track will be that processed by he Kaoss.
So? Forgive me if I'm just misunderstanding you, but:
The INPUT is the physical socket that the sound is coming INTO the computer through.
The OUTPUT is the physical socket that the sound is going OUT OF the computer through.
If you're sending the dry signal out of the computer to the Kaoss pad through the headphone out, that headphone out is your OUTPUT.
If that signal is run through the Kaoss pad and from there into the computer through the Apogee's Input 1, then the Apogee Input 1 is the INPUT channel that you need to select on the new track in Logic.
Logic 9 will output and input to/from different devices at the same time, so you won't need to build an aggregate device. However, if you change the output device to the headphone out, no sound will come out of the Apogee's output (which I assume is hooked up to your monitors), so you won't actually hear what you're doing until you're done recording and switch the output back.

Cron won't run ioreg, even though I can by hand - ADVANCED UNIX HELP NEEDED

This is driving me crazy. Cron will not run the ioreg command.
I have a script that does the following:
#! /bin/tcsh
set THEDATE = `date`
set ME = `whoami`
echo -n "$ME; $1; $THEDATE; " >> ~/Documents/BatteryStat/battery.log
ioreg -f -n AppleSmartBattery -r | grep -e 'ExternalConnected\|CurrentCapacity\|FullyCharged\|Amperage\|LegacyBatteryInfo\ |AvgTimeToFull\|AvgTimeToEmpty\|DesignCapacity\|Temperature\|CellVoltage\|Instan tAmperage\|CycleCount\|Voltage\|IsCharging\|InstantTimeToEmpty\|TimeRemaining\|M axCapacity' | tr '\n' ';' >> ~/Documents/BatteryStat/battery.log
echo >> ~/Documents/BatteryStat/battery.log
If I run it from the command line I get what I expect: a bunch of data dumped to this log file. If I stick it into cron, however, I only get my login, the first argument to the script and the date. No output from the ioreg command.
I know that cron is really just a wrapper for launchd or something like that and that the issues I am having have to do with the fact that the "user" under which the cron job is running is not the console user. Or something like that. It is all just a bit over my head. But it is certainly driving me completely insane!
Does anyone have any ideas how to make cron actually do something useful? (this is the second time that I have tried to use cron for a script and the second time it refuses to run for what I am guessing are similar reasons).
Any help is (or even just clues are) greatly appreciated.
ben

Absolute paths. Of course. Seems so obvious now but it really had me stumped. Absolute paths solved it. Mark, thank you SO much.
My machine has been acting really really flaky with the battery and this script will hopefully help me either get a new one or find out if the PMU is the problem.
Ray, I tried looking for the UNIX forum, but I can't find it (which is rather embarrassing... being so lost that you cannot even find the the forum where you would ask for directions). Where is it?
Thanks again for your help.
Ben

Help needed for (Null) showing as device name on router

Hi all .... facing a little issue with my imac?
I have recently bought some software that I need to connet to my local network. Well my network iMac device name was showing on my router (attached devices) as imac-a2gh6b but now for some reason it has changed to (null) - seee image - the software I am trying to use needs to use the local network to communicate between the 3 seperate programs.
The software is NCH Accounts Express / Express Invoice / Inventoria
Here is a screenshot of the advanced routing section in Inventoria ... as you can see my Computer Host: [(null)] and it used to be Computer Host: [imac-a2gh6b]

Hello PClaus. Welcome to the Apple Discussions!
In order to administer your new AirPort Express Base Station (AXn), the computer has to have the AirPort Utility installed. This will either be available with OS X Leopard or on the installation CD that came with the AXn. If your desktop Mac is not wireless, then the only way to access the AXn would be to connect the AXn directly to the Mac with Ethernet or connect both the AXn and your Mac to an Ethernet switch. Since you state that your laptops are wireless, I suggest using one of them to do the administration. Let me know if you were successful.

Help required to customize Simple/Advanced Search. Need to add new fields

Hello,
Module: Oracle Sales Online
EBS version: 12.1.3
Jdev version: 10.1.3.3
Scenario:
- We are dealing with standard oracle pages.
- We have TWO "SIMPLE/ADVANCED SEARCH"s available. Each "Simple/Advanced Search" can be found by navigating through paths "A --> B" and "A --> B --> C --> D" . Here it means one "SIMPLE/ADVANCED SEARCH" page is available at page "B" and another "SIMPLE/ADVANCED SEARCH" is available at page "D".
- In the first search page which is at page "B", both Simple as well as Advanced search has a filter field "Win Probability %", of type VARCHAR2/DROPDOWN with values (10, >=10, <=30, 30, >=30, <=50, 50, >=50, <=70, 70, >=70, <=90, 90, 100)
- In second search page, referring to page "D", the Simple search DOESN'T have the "Win Probability %". And the Advanced Search page has the "Win Probability %" but it is of type - NUMBER/MessageTextInput type.
Issue/Requirement:
- The 2nd Simple/Advanced search pages need to have "WIN PROBABILITY %" field and it should be of VARCHAR2/DROPDOWN with values (10, >=10, <=30, 30, >=30, <=50, 50, >=50, <=70, 70, >=70, <=90, 90, 100) just like the way we had in 1st Simple/Advanced search.
Note:
- Again speaking we are dealing with standard oracle pages
- If you go to the "About this Page", interestingly I found:
i. The "message component layout" for both of them is from the same region , i.e., ASNOpptympSrchRN
ii. Rest of the search filters for both the searchs are from common View Object , i.e., OpptySearchVO1 (for Simple search), OpportunityDetailsVO1 (for advanced search)
iii. The "Stack layout" for both the search pages are same, i.e. XXMASOpptyQryCO
iv. None of the fields are rendered to false (everything is set to be rendered TRUE)
Any response is highly appreciated.
Thanks,
Anand
Edited by: 933590 on Jul 19, 2012 8:18 AM

"XXMASOpptyQryCO is the name of stacklayout or CO?
What is the CO?
Does both pages share same CO?
have you already extended the CO "XXMASOpptyQryCO"?
what is the original CO then? I think in that CO it must be written somewhere, simple search "search allowed = false""
-Here CO what you are referring is a controller.
-FYI pages share same controller.
-And the original controller for both the pages are OpptyUwqCO. Right now its extended controller is XXMASOpptyQryCO
Fact is I didn't create this search page. It was built by some third party members. Also that I do not have the original source nor the documentation pertaining to it. So could you inform as in how should I navigate to the point "Search Allowed = True"
I should have informed that at "B" page, it has a region /oracle/apps/asn/opportunity/webui/ASNMgrOpptyQryRN and at page "D", the region is /oracle/apps/asn/opportunity/webui/ASNOpptyQryRN
Edited by: 933590 on Jul 19, 2012 1:37 PM

WRT54G Advanced Routing

I currently have a WRT54G as a Gateway to my network. The ISP connection plugs into the WAN port, and then the WRT54G plugs into a switch, and all other computers plug into the switch. The router's internal address is 192.168.1.1 /24 and all computers get a DHCP address from the WRT54G from 192.168.1.50-150 /24.
I am putting in a Sonicwall (I will give it address 192.168.1.2) and want the WRT54G to use the Sonicwall as the Gateway; that is, plug the ISP into the Sonicwall, and connect the Sonicwall to the WRT54G, and all other connections remain the same. I know I have to use Advanced Routing to switch from Gateway to Router mode, but I am unsure what the other settings should be (RIP, Select Set Number, Destination LAN IP, etc.) The WRT54G must remain in the network. How can I make this work?

Thanks for replying, but I'm hoping to get some help with this problem. The device needs to be in the chain, and I have done it before, so I know it can work, but sadly, I did not document how I made it work =/
"I currently have a WRT54G as a Gateway to my network. The ISP connection plugs into the WAN port, and then the WRT54G plugs into a switch, and all other computers plug into the switch. The router's internal address is 192.168.1.1 /24 and all computers get a DHCP address from the WRT54G from 192.168.1.50-150 /24.
I am putting in a Sonicwall (I will give it address 192.168.1.2) and want the WRT54G to use the Sonicwall as the Gateway; that is, plug the ISP into the Sonicwall, and connect the Sonicwall to the WRT54G, and all other connections remain the same. I know I have to use Advanced Routing to switch from Gateway to Router mode, but I am unsure what the other settings should be (RIP, Select Set Number, Destination LAN IP, etc.) The WRT54G must remain in the network. How can I make this work?"

E1700 Advanced Routing - help needed

Similar Messages

Maybe you are looking for