E2000 SLOW AND SIGNAL VARIES
I have a couple of Vista laptops that used to access our home network via Linksys Wireless-G Access Point and that in turn was connected to a Linksys BEFSR41 v2 EtherFast Cable/DSL 4 port Router which in itself was connected to our cable modem from TIme Warner (RoadRunner service).
The cable modem is new and was working fine with the WAP setup.
To "simplify" things I recently bought a Cisco Linksys E2000 Advanced Wireless-N Router which i connected directly to our cable modem.
Our web browsing is now slow, the signal strength comes and goes (from 2 bars to 5 bars, although RARELY 5 bars). We are at most 80 feet from the router. there is literally no interference beyond the drywall separating our laptops form the basement (the WAP and Router were also originally in the basement).
I have already done all the things I have read about in this forum (re-installed, changed channels, no parental controls, updated firmware, no guest option, etc).
Unless someone has a new idea I am thinking of throwing this thing out and getting something else but I am giving it one more chance through this forum.
Thanks for any advice you can provide!
Try to change some of the advanced wireless settings on the router like Change the Beacon Interval to 75,Change the Fragmentation Threshold to 2304,Change the RTS Threshold to 2304 and Click on Save Settings.
Similar Messages
-
Why is my iPhone so slow and signals are jumping in and out
My iphone is failing my with the signals after i updated the software to ios7
Any change after a reset which is similar to a computer restart and is done by pressing and holding the home button and the sleep/wake or on/off button simultaneously until you see the Apple logo and then release?
-
I have a 10 mb/s timewarner cable connection thru linksys E2000. I was having an issue of the connection speed limited to 5 mb/s after E2000 wired and wireless. If i take out the router then i get 10 mb/s.
The fix i found is to setup your router without Cisco Connect. Although i wont be about to setup guest accounts anymore, but i get the speed now.
This may or may not work for you. If it does, I assume it would work for E3000 and E4000 also.
PS. All i did was press reset buttom for 30 sec then unplug, wait for another 10 sec and plug back in. Ran setup from web http://192.168.1.1 . done.You can even try to adjust the slow speed for the connection of wired and wireless both for E2000 through Cisco Connect by the follow steps as well:
If you configured the Router with the help of the Cisco Connect Software then open that up in which you have installed… There you will be able to see 4 small window screens…
You have to click on “Router setting” window…
Then click on “Advanced settings” button… That opens the Router Setup page….
# In the same setup page try to reduce the MTU size to 1400 from Auto… Save Settings…
# Then go to Wireless tab make the changes for the channel –
For Channel Settings of 2.4 GHz you can make Channel Width to 20 MHz only and Channel to 6, 9, 11..
For Channel Settings of 5 GHz you can make Channel Width to 20 MHz only and Channel to 40 or 161...
Then check the speed status…. -
My original iPad is slow and drops web pages and videos all the time now. Is the software just too old to handle the technology changes on the websites and video or is it a virus or junk in the iPad causing this? I have plenty or storage left on the iPad like 18GB. Sure would like to know. Maybe it is just too old to handle things now?
IIf you are running iOS 6.1.2, you could not be using the original iPad. No matter which iPad and what version, try these basic troubleshooting steeps and see if it helps with the performance.
Go to Settings>Safari>Clear History and Website Data. Then close all apps.
In order to close apps in iOS 5 or iOS 6, first tap the home button once. Then tap the home button twice and the recents tray will appear at the bottom of the screen. Tap and hold down on any app icon until it begins to wiggle. Tap the minus sign in the upper left corner of the app that you want to close. Tap the home button twice.
In order to close apps in iOS 7 or 8, you have to drag the app up from the multitasking display. Double tap the home button and you will see apps lined up going left to right across the screen. Swipe to get to the app that you want to close and then swipe "up" on the app preview thumbnail to close it.
Now reset your iPad. Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.
You can also try resetting all settings. You will not lose any data, but most of the device settings will have to be entered in the settings app again. Settings>General>Reset>Reset all Settings. -
Older Mac Book Pro is slow and bogging down
My older Mac Book Pro is getting slow and having issues like a PC (programs freeze and closes, slow to respond, slow to open programs, wifi signal dropps out, etc)
Is there a way to restore the performance, maybe by doing a wipe and a time machine restore?
The hard drive is only 2/3 full and I don'e run a lot of high demand programs.Sarmaticus wrote:
I seem to have read somewhere that the Mac does auto-defragging during late night admin sessions (on certain dates only) if your computer is left switched on overnight. Perhaps someone more knowledgeable would have a little more about this....
Ah, there you go. It's in the MacLife article mentioned by shoulder2thewheel: 3.15am nightly admin sessions. Just need to leave your Mac on.
Not good if you have loads of bad sectors though, as you may find that system files will be written over the bad sectors... and hey presto, you have a fatal disk crash, just like on my computer two nights ago. -
Recently started running slow and freezing up while loading web pages etc.
Problem description:
Computer running slow and freezes up for a few minutes from time to time, I have owned it since 2011 with no issues until now.
EtreCheck version: 2.1.2 (105)
Report generated December 15, 2014 at 9:58:50 AM MST
Hardware Information: ℹ️
MacBook Pro (13-inch, Early 2011) (Verified)
MacBook Pro - model: MacBookPro8,1
1 2.3 GHz Intel Core i5 CPU: 2-core
4 GB RAM Upgradeable
BANK 0/DIMM0
2 GB DDR3 1333 MHz ok
BANK 1/DIMM0
2 GB DDR3 1333 MHz ok
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
Intel HD Graphics 3000 - VRAM: 384 MB
Color LCD 1280 x 800
System Software: ℹ️
OS X 10.10.1 (14B25) - Uptime: 0:10:42
Disk Information: ℹ️
Hitachi HTS545032B9A302 disk0 : (320.07 GB)
S.M.A.R.T. Status: Verified
EFI (disk0s1) <not mounted> : 210 MB
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
Macintosh HD (disk1) / : 318.84 GB (24.01 GB free)
Core Storage: disk0s2 319.21 GB Online
MATSHITADVD-R UJ-8A8
USB Information: ℹ️
Apple Inc. FaceTime HD Camera (Built-in)
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Computer, Inc. IR Receiver
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Configuration files: ℹ️
/etc/launchd.conf - Exists
Gatekeeper: ℹ️
Mac App Store and identified developers
Adware: ℹ️
Geneio [Remove]
Kernel Extensions: ℹ️
/System/Library/Extensions
[not loaded] com.mice.driver.PS3Controller (1.0.0d1) [Support]
Launch Agents: ℹ️
[running] com.amazon.sendtokindle.launcher.plist [Support]
[running] com.robohippo.HippoConnectAgent.plist [Support]
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist [Support]
[loaded] com.microsoft.office.licensing.helper.plist [Support]
[not loaded] com.robohippo.HippoConnectDaemon.plist [Support]
User Launch Agents: ℹ️
[loaded] com.genieo.completer.download.plist Adware! [Remove]
[loaded] com.genieo.completer.update.plist Adware! [Remove]
[loaded] com.google.keystone.agent.plist [Support]
[invalid?] com.nds.pcshow.plist [Support]
[invalid?] com.nds.pcshow.uninstall.plist [Support]
User Login Items: ℹ️
iTunesHelper UNKNOWNHidden (missing value)
Internet Plug-ins: ℹ️
FlashPlayer-10.6: Version: 16.0.0.235 - SDK 10.6 [Support]
Default Browser: Version: 600 - SDK 10.10
AdobePDFViewerNPAPI: Version: 11.0.09 - SDK 10.6 [Support]
AdobePDFViewer: Version: 11.0.09 - SDK 10.6 [Support]
Flash Player: Version: 16.0.0.235 - SDK 10.6 [Support]
QuickTime Plugin: Version: 7.7.3
SharePointBrowserPlugin: Version: 14.4.6 - SDK 10.6 [Support]
Google Earth Web Plug-in: Version: 7.1 [Support]
Silverlight: Version: 5.1.30514.0 - SDK 10.6 [Support]
iPhotoPhotocast: Version: 7.0 - SDK 10.7
Safari Extensions: ℹ️
Omnibar Adware! [Remove]
3rd Party Preference Panes: ℹ️
Flash Player [Support]
Time Machine: ℹ️
Time Machine not configured!
Top Processes by CPU: ℹ️
17% mds
6% WindowServer
0% AppleSpell
0% fontd
0% mds_stores
Top Processes by Memory: ℹ️
120 MB Safari
77 MB mds_stores
69 MB com.apple.WebKit.WebContent
60 MB ocspd
60 MB WindowServer
Virtual Memory Information: ℹ️
1.24 GB Free RAM
1.15 GB Active RAM
853 MB Inactive RAM
1.05 GB Wired RAM
1.00 GB Page-ins
25 KB Page-outs
Diagnostics Information: ℹ️
Dec 15, 2014, 09:48:45 AM Self test - passed1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of the script have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts SerialATA 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports ' com.clark.\* \*dropbox \*genieo\* \*GoogleDr\* \*k.AutoCAD\* \*k.Maya\* vidinst\* ' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 "` route -n get default|awk '/e:/{print $2}' `" 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB ' com.adobe.AAM.Updater-1.0 com.adobe.AAM.Updater-1.0 com.adobe.AdobeCreativeCloud com.adobe.CS4ServiceManager com.adobe.CS5ServiceManager com.adobe.fpsaud com.adobe.SwitchBoard com.adobe.SwitchBoard com.apple.aelwriter com.apple.AirPortBaseStationAgent com.apple.FolderActions.enabled com.apple.installer.osmessagetracing com.apple.mrt.uiagent com.apple.ReportCrash.Self com.apple.rpmuxd com.apple.SafariNotificationAgent com.apple.usbmuxd com.citrixonline.GoToMeeting.G2MUpdate com.google.keystone.agent com.google.keystone.daemon com.microsoft.office.licensing.helper com.oracle.java.Helper-Tool com.oracle.java.JavaUpdateHelper com.oracle.java.JavaUpdateHelper org.macosforge.xquartz.privileged_startx org.macosforge.xquartz.privileged_startx org.macosforge.xquartz.startx ' ' 879294308 4071182229 461455494 3627668074 1083382502 1274181950 1855907737 2758863019 1848501757 464843899 3694147963 1233118628 2456546649 2806998573 2778718105 2636415542 842973933 2051385900 3301885676 891055588 998894468 695903914 1443423563 4136085286 523110921 2883943871 3873345487 ' 51 5120 files );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^\([0-9]+\) /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n-\t%s\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' s/[0-9A-Za-z._]+@[0-9A-Za-z.]+\.[0-9A-Za-z]{2,4}/EMAIL/g;/faceb/s/(at\.)[^.]+/\1NAME/g;/\/Shared/!s/(\/Users\/)[^ /]+/\1USER/g;s/[-0-9A-Fa-f]{22,}/UUID/g;' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: (E[^m]|[^EO])|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<10) print "com.apple.";} ' ' { sub(/ :/,"");print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:.+//p ' '/^root$/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1100) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".(/private)?","");n++;print;} END { split("'"${p[41]}"'",b);split("'"${p[42]}"'",c);for(i in b) print b[i]".plist\t"c[i];if(n<500) print "Launch";} ' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| |\n","\\|\\|kMDItem'${p[35]}'=");sub("^...."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[43]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/{next};/%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";p="uniq -c|sed -E '"'s/ +\\([0-9]+\\)\\(.+\\)/\\\2 x\\\1/;s/x1$//'"'";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1|p;b=b$1;} END { close(p);if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"cksum "F|getline C;split(C, A);C="checksum "A[1];"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text(, with v.+)?$|(Bo|PO).+ sh.+ text ex|XM)/) F=F" ("T", "C")";else F=F" ("C")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / / { print "'"${p[28]}"'";exit;};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/\(L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9|"sort|uniq";} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ /V/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' ' /^find: /d;p;' "`S0 44 45`" ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ *$/d;s/^ */ /;' ' s/^.+ |\(.+\)$//g;p ' '/\.(appex|pluginkit)\/Contents\/Info\.plist$/p' ' /2/{print "WARN"};/4/{print "CRITICAL"};' ' /EVHF|MACR|^s/d;s/^.+: //p;' ' $3~/\./ { i++;n=n"\n"$1"\t"$3;} END { if(i>1) print n;} ' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps crontab iotop top pkgutil 'PlistBuddy 2>&1 -c "Print' whoami cksum kextstat launchctl smcDiagnose sysctl\ -n defaults\ read stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' pluginkit scutil dtrace profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil lsof test osascript\ -e netstat );c2=(com.apple.loginwindow\ LoginHook '" /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'|tr , \\\n" 'L*/Ca*/com.ap*.Saf*/E*/* -d 1 -name In*t -exec '"${c1[14]}"' :CFBundleDisplayName" {} \;|sort|uniq' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 \)' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' :${p[35]}\" :Label\" '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$(RefProc): \$Message' -k Sender Req 'fsev|kern|launchd' -k RefProc Rne 'Aq|WebK' -k Message Rne 'Goog|ksadm|probe|Roame|SMC:|smcD|sserti|suhel| VALI|ver-r|xpma' -k Message Req 'abn|bad |Beac|caug|corru|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|NVDA\(|pagin|pci pa|proc: t|Roamed|rror|SL|TCON|Throttli|tim(ed? ?|ing )o|WARN' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cght] ! -name .?\* ! -name \*ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true \) -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '/S*/*/Ca*/*xpc* >&- ||echo No' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,Ex}* {/,}L*/{A*d,Ca*/*/Ex,Co{mpon,reM},Ex,In{p,ter},iTu*/*P,Keyb,Mail/B,Pr*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -path \\*s/Resources -prune -o -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,mach_i*/*,pam.d/*,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t {/S*/,/,}L*/Lau*/*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' '+c0 -i4TCP:0-1023' com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' "+c0 -l|awk '{print(\$1,\$3)}'|sort|uniq -c|sort -n|tail -1|awk '{print(\$2,\$3,\$1)}'" -m 'L*/{Con*/*/Data/L*/,}Pref* -type f -size 0c -name *.plist.???????|wc -l' kern.memorystatus_vm_pressure_level '3>&1 >&- 2>&3' " -F '\$Time \$Message' -k Sender kernel -k Message CSeq 'n Cause: -' " -i );N1=${#c2[@]};for j in {0..9};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents XPC\ cache Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching SATA Descriptors App\ extensions Lockfiles Memory\ pressure SMC Shutdowns Nets );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};A'$((7+i))'() { v=` eval sudo "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};';done;A9(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0() { [[ "$v" ]]&&sed -E "$s"<<<"$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v"|sed -E "$s";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "${s[63]}"<<<"$v"`&&C1 1 $1;};for i in 1 2 7 8;do for j in 0 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;D20 0 $((N1+1)) 2;D10 0 $N1 1;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;D13 0 $((N1+9)) 59 50;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;B1&&D73 19 53 67 55;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 54 12 56;D23 5 14 12 14;D22 6 36 13 15;D22 20 52 66 54;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D82 35 49 61 51;D82 11 17 17 20;for i in 0 1;do D82 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A8 18 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;B3 4 0 65;A3 14 6 32 0;B4 0 16 11;A1 26 50 64;B7 16;C3 52;D13 24 24 32 31;D13 25 37 32 33;A2 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D73 21 0 32 19;D73 10 42 32 40;D82 29 35 46 39;};D23 14 1 62 42;D12 34 43 53 44;D12 22 20 32 25;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 21 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 38 55 68 57;D23 33 34 42 37;B1&&D83 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 10 42 32 41;D13 37 2 48 43;D13 4 5 32 1;D13 4 3 60 5;D12 21 48 49 49;B3 4 22 57;A1 21 46 56;B7 22;B3 0 0 58;C3 47;D22 4 4 50 0;D12 4 51 32 53;D23 22 9 37 7;A9;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report what happened. No harm will be done.
12. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed. -
15" 2011 brain-bombingly slow and has a hobby of crashing as often as it can
I just bought my Mac Pro 15" in April to replace my netbook. I expected to get high performance for all that money.
However, its slowness almost competes with my old, cheap netbook. In addition to that the system and the apps (esp. iPhoto) casually crash. I've had a couple of serious problems with this mac, in one of which incidents the machine refused to boot, that required me to call customer service. I contacting customer service with this slowness and crashing issue, but having experienced how long it took to get my mac back to working with the Apple help only through the phone, I decided going to Apple store would be the best bet. However, I am traveling in one of the poorer countries in the world and will be for the next few months, and I do not think a visit is an option for me.
Has anyone else experienced this problem with the new mac? Are macs usually this ******** despite their fame? If this near $2k machine is as ******** as this, it makes me wonder if that money was an unnecessary donation to this company.1. Booting speed for the system is usually fine. Booting speed for applications varies from time to time although the booting speed has not been the biggest problem. iTunes at this moment booted nearly immediately. I recollect at other times it has taken 0-10 s.
2. I usually use 3-5 applications at a time. I would normally use more but because of the slowness I have been limiting myself to these numbers. Crashes happen most with iPhoto. I think there may be a problem with the software, but for some reason I get an error message every time I attempt to update the software.
The system itself has crashed a number of times. It stops without warning, goes into the blue screen and either returns to the previous screen or shuts down every application and starts again (it has rebooted on its own a few times, but in other times it just refreshed its system without a reboot).
The slowness problem goes across every application which makes me think it's the problem with the OSX and/or the machine. It has been unexpectedly slow since the time I bought it. It may have grown slower recently if it's not my patience that's being depleted. The machine takes almost every kind of task, so often, very hard to process.
3. I do not think so. When Chrome crashes, which it has done, I know it's the problem with the brower because I experienced it with other laptops. However there have been instances where I have tried both Firefox and Safari as well as Chrome accomplish certain tasks and they all crashed. I think they were related to iPhoto. Javascript fails occasionally as well.
4. I have used it just two weeks or so ago because my system failed almost completely and I could not boot the computer. At that time I called Customer Service and the representative directed me to use the utility after doing many things to log into Safe Mode.
Is there a specific way to keep crash logs? Or does it just involve me writing down what happens? How can I document my MBP's performance?
Thank you very much for your help. -
Airport Time Capsule purchased in Canada, trying to set up in home in Mexico. Connected to isp via ethernet cable, tried resets and power off/on on both TC and isp modem. TC flashes amber (slow), and is not picked up by Airport Utility on Macbook or iPad. Do I have a faulty TC that has to be returned? Wireless signal from provider is strong and reliable for last 5 yrs. Please help
Got it figured :-) Unable to pick up TC via Airport Utility on MacBook Pro or iPad. Used iPad via Settings-WiFi to pick up TC and enter edit functions. Once WAN deselected, Bridge selected, DHCP selected got the steady green light on the TC. Airport utility now picks up the TC no problem on both iPad and Macbook. System now fully operational.
-
Broadband getting slower and slower
Hi,
For the past few weeks broadband has been getting slower and slower, from about 2.5Mbps down to 0.3Mbps so far.
ADSL line status
Connection Information
Line state
Connected
Connection time
1 days, 04:44:50
Downstream
287 Kbps
Upstream
924 Kbps
ADSL Settings
VPI/VCI
0/38
Type
PPPoA
Modulation
G.992.5 Annex A
Latency type
Interleaved
Noise margin (Down/Up)
7.1 dB / 5.5 dB
Line attenuation (Down/Up)
58.9 dB / 35.0 dB
Output power (Down/Up)
1.5 dBm / 1.4 dBm
Loss of Framing (Local/Remote)
0 / 0
Loss of Signal (Local/Remote)
0 / 0
Loss of Power (Local/Remote)
0 / 0
FEC Errors (Down/Up)
7780 / 2
CRC Errors (Down/Up)
43 / 1
HEC Errors (Down/Up)
6 / 0
Error Seconds (Local/Remote)
15 /
I have reported the fault a number of times, but have been told 'we cannot find a fault', and line tests report there is no problem.
The quiet line test sounded ok, everything is plugged into the master socket with a filter.
This is the same as a problem i had before, which was fixed after posting on this forum.
Hopefully someone who can help will see this and be able to get it fixed.
ThanksHi Welcome to the forums
Here is a basic guide to getting help from the community members done by CL Keith Please read through the link posted http://forumhelp.dyndns.info/speed/first_steps.html
Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
once you have posted the information asked for then the community members can help you more
Thank You
This is a customer to customer self help forum the only BT presence here are the forum moderators
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’ -
BT Infinity 2 very very slow and cutting out
Hi,
BT contacted me some months ago offering me a free update to get faster broadband speeds on the condition that I signed a contract for a further 12 months. I agreed to this but since then the speeds have been getting slower and slower and now at time cut out completely. Hardly an upgrade is it.
I've removed the game console and have less tablets now using the broadband, so I now have much less connected to the broadband yet it is still slower than before the upgrade.
I've tried having a live webchat to get the problem sorted but of course the signal keeps on cutting out.
Anyone else had any issues?
ThanksGood afternoon John1975, and welcome to the forum.......
Can you put your telephone number into http://www.dslchecker.bt.com/adsl/adslchecker.welcome and post the results (after removing your telephone number) ?
Can you log-in to your homehub and post the first 12 lines that show under the "helpdesk" tab, assuming that is, that you have a Homehub 5 ?
Can you carry out the "quiet line" test ? Using a corded phone plugged into the test socket on the master socket, dial 17070 and choose option 2. There should be no crackles, popping, buzzing, etc, in fact, it should be quiet........
If you found this post helpful, then please click the star on the left, after all, I'm only trying to help........ -
For the past week my bb speed has become slower and slower. The speed today Sunday 17th is a staggering 291kbs. How am I meant to remain sane using this. I have contacted bt and all they do in broken english is to tell me it will settle down and get better. Last month speed was fine but now OMG. With this bad service BT are open to losing me as I have a right now to cancell my contract due to the service.
Am I the only person putting up with this rubbish service (or lack of).
Solved!
Go to Solution.this is the hub report but if I do a speed test
on other test sites it comes back as mega slow.
ADSL Line Status
Connection Information
Line state:
Connected
Connection time:
0 days, 02:12:02
Downstream:
2.75 Mbps
Upstream:
448 Kbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.1 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
8.7 dB / 21.0 dB
Line attenuation (Down/Up):
54.6 dB / 31.5 dB
Output power (Down/Up):
17.8 dBm / 12.2 dBm
FEC Events (Down/Up):
4667117 / 339
CRC Events (Down/Up):
5113 / 367
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
72379 / 418
Error Seconds (Local/Remote):
593 / 249 -
I recently bought a new 13 inch Macbook air and wireless internet is really slow and disconnect again and again. However I hav another windows laptop at the same place and that never disconects or looses signals? wireless on this mac is too slow that I cannot even use to make a skype call. I am new mac user and getting a bit disappointed because of this bad performance.I googled about this issue and found that lot of people are having the same issue with macbook air. I switched off the bluetooth adaptor but still no progress. Any help will be appreciated. Thanks
I am experiencing something similar with my MBA 13"/i5/256GB.
To take it one step further, I started up a Terminal session and ran a ping against my wireless router. I see the same pattern repeated over and over: I get about 5 or 6 pings through, then 4 or 5 misses, then it reconnects again. When it reconnects, the first ping or two have times in thousands of milliseconds, where normal is maybe sub-millisecond to 4ms for the remaining few seconds.
I have other wireless devices, including iPhone, iPad, and an older MacBook - all work fine. The MBA is the only Lion device. -
Since installing LTR 5.4, which I've now upgraded to 5.6, I've encountered repeated slowness and malfunctions in operations, especially when using the Compare View function and the Tab key to open and close the right and left side panels. Such problems never arose during two years of using LTR-4 and nothing else has changed on my computer. I have a pretty simple system with only a few plug-ins, which are usually not in operation. I have 12GB of RAM in my Windows 7 PC. I could illustrate these problems with screen shots if you would tell me how to submit screen shots. Otherwise I will try to describe the problems in words.
The problem is clearly cumulative, growing worse as usage time passes. Compare View feature gradually slows down and eventually seems to choke as my work session proceeds. If I Exit LTR and re-enter and start all over, things will work normally for maybe 30 minutes, but then the Compare View feature begins to become very slow to respond. In a recent example with my screen full of thumbnails in Library mode I highlighted two images to compare. LTR started to open the Compare View screen by first having the top row of thumbnails disappear to be replaced by the "SELECT" and "CANDIDATE" words in their spaces (but no images), but Compare View never succeeded in gaining control of the screen. After some seconds the top row of thumbnails reasserted its position and the Compare View windows disappeared. But LTR kept trying to bring them back. Again the top row of thumbnails would go away, Select and candidate would reappear, try again, and give up. This went on for at least 2-3 minutes before I tried to choose File and Exit, but even that did not initially want to respond. It doesn't like to accept other commands when it's trying to open Compare View. Finally it allowed me to exit.
To experiment I created a new catalog of 1100 images. After 30-40 minutes, the Compare View function began to operate very slowly. With left and right side panels visible and two thumbnails highlighted, hitting Compare View can take half a minute before the two mid-size images open in their respective SELECT and CANDIDATE windows. When the side panels are open and two images are in the Select/Candidate spaces, hitting the Tab button to close the side panels produces a very delayed response--25-30 seconds to close them, a few more seconds to enlarge the two images to full size. To reverse the process (i.e., to recall the two side panels), hitting Tab would make the two sides of the screen go black for up to a minute, with no words visible. Eventually the info fields in the panels would open up.
I also created a new user account and imported a folder of 160 images. After half an hour Compare View began mis-placing data. (I have a screen shot to show this.) CANDIDATE appears on the left side of SELECT, whereas it should be on the right. The accompanying camera exposure data appears almost entirely to the left of the mid-screen dividing line. Although the Candidate and Select headings were transposed, the image exposure data was not, but the data for the image on the right was almost entirely to the left of the line dividing the screen in two.
Gurus in The Lightroom Forum have examined Task Manager data showing Processes running and Performance indicators and they see nothing wrong. I could also send screen shots of this data.
At this point, the only way I can process my images is to work 30-40 minutes and then shut down everything, exit, and re-start LTR. This is not normal. I hope you can find the cause, and then the solution. If you would like to see my screen shots, tell me how to submit them.
Ollie
[email protected]Since installing LTR 5.4, which I've now upgraded to 5.6, I've encountered repeated slowness and malfunctions in operations, especially when using the Compare View function and the Tab key to open and close the right and left side panels. Such problems never arose during two years of using LTR-4 and nothing else has changed on my computer. I have a pretty simple system with only a few plug-ins, which are usually not in operation. I have 12GB of RAM in my Windows 7 PC. I could illustrate these problems with screen shots if you would tell me how to submit screen shots. Otherwise I will try to describe the problems in words.
The problem is clearly cumulative, growing worse as usage time passes. Compare View feature gradually slows down and eventually seems to choke as my work session proceeds. If I Exit LTR and re-enter and start all over, things will work normally for maybe 30 minutes, but then the Compare View feature begins to become very slow to respond. In a recent example with my screen full of thumbnails in Library mode I highlighted two images to compare. LTR started to open the Compare View screen by first having the top row of thumbnails disappear to be replaced by the "SELECT" and "CANDIDATE" words in their spaces (but no images), but Compare View never succeeded in gaining control of the screen. After some seconds the top row of thumbnails reasserted its position and the Compare View windows disappeared. But LTR kept trying to bring them back. Again the top row of thumbnails would go away, Select and candidate would reappear, try again, and give up. This went on for at least 2-3 minutes before I tried to choose File and Exit, but even that did not initially want to respond. It doesn't like to accept other commands when it's trying to open Compare View. Finally it allowed me to exit.
To experiment I created a new catalog of 1100 images. After 30-40 minutes, the Compare View function began to operate very slowly. With left and right side panels visible and two thumbnails highlighted, hitting Compare View can take half a minute before the two mid-size images open in their respective SELECT and CANDIDATE windows. When the side panels are open and two images are in the Select/Candidate spaces, hitting the Tab button to close the side panels produces a very delayed response--25-30 seconds to close them, a few more seconds to enlarge the two images to full size. To reverse the process (i.e., to recall the two side panels), hitting Tab would make the two sides of the screen go black for up to a minute, with no words visible. Eventually the info fields in the panels would open up.
I also created a new user account and imported a folder of 160 images. After half an hour Compare View began mis-placing data. (I have a screen shot to show this.) CANDIDATE appears on the left side of SELECT, whereas it should be on the right. The accompanying camera exposure data appears almost entirely to the left of the mid-screen dividing line. Although the Candidate and Select headings were transposed, the image exposure data was not, but the data for the image on the right was almost entirely to the left of the line dividing the screen in two.
Gurus in The Lightroom Forum have examined Task Manager data showing Processes running and Performance indicators and they see nothing wrong. I could also send screen shots of this data.
At this point, the only way I can process my images is to work 30-40 minutes and then shut down everything, exit, and re-start LTR. This is not normal. I hope you can find the cause, and then the solution. If you would like to see my screen shots, tell me how to submit them.
Ollie
[email protected] -
Multiple (but separate) domain problem & Apple's slow and useless response
I am having problem with multiple (but separate) domain. I opened a ticket.
Here is Apple's slow and useless response and my follow up.
This follow up is not going to resolve the issues I am having. The sites are not in one domain file. I have split them into separate domains. I found that the simplest change to any page made the publishing process extremely and reasonably slow. If I updated a single site, iWeb republishes the whole conglomeration; hardly the most efficient way.
I have several directories under the ~/Library/Application Support/iWeb/ directory with separate Domain.sites2 files for each site:
consultingAM.com
DarkAssassinMovie.com
Fuzzy Llama Junior Optimist Club
GulfportOptimist.com
OptimistView
pAwesomeProductions.com
www.nfdoi.com
With the previous version of iWeb, I navigated to a specific ~/Library/Application Support/iWeb/ directory, selected the Domain.site file, and opened it. This would open iWeb with the selected domain. Several of the sites have their blog page with the RSS subscribe option.
Once I made the update, all I usually had to do was publish site and all was well. Occasionally, I would have to do a publish all if I changed domains. All in all, I had no problems with publishing once I found the right steps to be able to maintain multiple domains.
Now, using the default publish or publish all process, all I get is the last site I published. In order to get things semi-functional, I published a site, then I would go to iDisk/Web/Sites/ directory, select the folder name for the site I had just published, then copy it or move it to iDisk/Web/Sites/iWeb directory. This was rather slow and I suspect it is not an approved solution, but it semi-worked. My sites are back up, but they are not fully functional.
Is there anyway to get back to using the ~/Library/Application Support/iWeb/ directory (separate Domain.sites file for each site) process to publish multiple sites? If not, is there any way to suck in the various domains back into one? If that is possible, will it take hours to publish the combined 2-3GB like it did with the previous version?
How do I reverse the 'personal domain' process? I do not want to do this at this time. I just wanted to see what the steps were. I have done the first step, but not the second.
I was glad to see some of the changes made in the upgrade (web widgets, maps, html snippets, theme switching), but I am too happy about the changes made by the upgrade process. In the past, I upgraded my Apple related stuff as soon as it came out. Based on this upgrade, that won't happen again.
It took you guys 5 days to get back to me (during which time several of my sites were down) and I do not believe the information you provided is going to solve my specific problems. I am very disappointed with the results of this upgrade. Clearly there was inadequate testing of this product before it was released. I cannot recall seeing the Apple discussion forums with hundreds of topics and thousands of posts within a week or two of a new release. Apple had to upgrade iWeb in the first week, another poor sign.
Apple is beginning to slip back to the pack; all vendors all below average. Apple is getting more like Microsoft everyday. First Apple delays the release of an OS upgrade so they can concentrate on a freaking phone, now you release software that is so buggy it should be classified as beta at best.
Some of the changes/problem I am seeing since the upgrade (in addition to the problems mentioned previously) are:
layout changes; some of my pages no longer look the same; same of the changes are so bad the pages are unreadable
broken photo pages; some of my photo pages no longer work; some of them have no text or pictures
file/page name changes; why would Apple change the location of the files; now my domains are not pointing right location; special characters (like spaces, ampersands, etc.) are handled differently in this version; specifically, I see that spaces are changed to underscores (_); iWeb used to use '%20' for spaces; what was Apple thinking?
broken 3rd party themes; I know Apple is not responsible for 3rd party themes, but you should certainly be aware that they exist
Based on what I am seeing online, most of the people who are complaining about major iWeb issues are not newbies; based on the technical details in the threads, there are clearly some experienced people who are trying to figure things outw. I have lost many hours trying to figure this mess out. I now have to review hundreds of pages to try get things to look and work the way they did before the upgrade. I have had to handle dozens of phone calls and emails from my viewers and subscribers trying to explain the situation.
I googled 'iweb 08 *****' and got nearly 50,000 hits! I think Apple better get in front of this train before it gets run over.
On Aug 19, 2007, at 11:09 AM, .Mac Support wrote:
Dear David,
I understand that you are experiencing an issue viewing some of your websites published in iWeb:
I have examined all of the published pages and they appear to load and function as expected. If you published your website to .Mac, you can visit it either of these ways:
- In iWeb, click the Visit button in the lower-left corner.
- Enter the following URL into a web browser:
http://web.mac.com/daviddawley/
If you have published more than one website, the URL above will take you to the default website, which is the first website listed in iWeb. To visit another website you have created in iWeb, use the following URL format:
http://web.mac.com/daviddawley/iWeb/YourSiteName
Using this form, the web addresses for the two sites you mentioned would be:
http://web.mac.com/daviddawley/iWeb/FuzzyLlamaJuniorOptimist.com
http://web.mac.com/daviddawley/iWeb/pAwesomeProductions.com
To change the default website, simply open iWeb, and in the Site Organizer, drag the desired default website to the top and republish to .Mac.
NOTE: Be sure to give each website a unique name. This will help prevent one website from overwriting another. For further information, refer to the following article:
iWeb: Do not use similar names for your sites
http://www.info.apple.com/kbnum/n303042
If you still experience issues with the website, try the following troubleshooting steps:
WAIT SEVERAL MINUTES
If your website has movies, you may need to wait several minutes after going to the website before the movies are ready to play. The QuickTime Player icon indicates that a movie is still loading.
CLEAR YOUR BROWSER CACHE
If you use Safari, you can clear your browser cache by choosing Empty Cache from the Safari menu. If you use another browser, consult that browser’s documentation if you need assistance in clearing your browser cache.
UPDATE YOUR BROWSER
Make sure you are using the latest available version of your web browser when viewing pages published in iWeb. If you use Safari, you can check for updates by choosing Software Update from the Apple menu. If there are any available Safari, Security, or Mac OS X updates, install those updates and try looking at your website again.
If you use another browser, consult that browser’s documentation if you need assistance in updating the browser.
TRY ANOTHER BROWSER
If you use a Mac, try viewing your website with Safari or Firefox. If you use Windows, try Internet Explorer 6 or Firefox. Firefox is a free download available here: http://getfirefox.com
TRY ANOTHER NETWORK
If possible, try viewing your website from another network or Internet connection. If you can successfully view the website from another network, please consult your network administrator or Internet service provider (ISP) to resolve this issue.
Important: Mention of third-party websites and products is for informational purposes only and constitutes neither an endorsement nor a recommendation. Apple assumes no responsibility with regard to the selection, performance, or use of information or products found at third-party websites. Apple provides this only as a convenience to our users. Apple has not tested the information found on these sites and makes no representations regarding its accuracy or reliability. There are risks inherent in the use of any information or products found on the Internet, and Apple assumes no responsibility in this regard. Please understand that a third-party site is independent from Apple and that Apple has no control over the content on that website.
Sincerely,
Mel
.Mac Support
http://www.apple.com/support/dotmac
http://www.mac.com/learningcenter
Support Subject : iWeb
Sub Issue : I can't publish to .Mac from iWeb
Comments : I was interested in forwarding one of several iWeb based sites to one of my domains. I wanted to see what the steps were. I believe I inadvertently started the process for moving the site to www.nfdoi.com site. I have several sub directories under the ~/Library/Application Support/iWeb directory with separate domain.sites files (now domain.sites2).
I was going through all of my domain.sites files and opening them in iWeb08; then publishing them. Somewhere along the line everything blew up. Most of my iWeb sites no longer function, It appears that every other iweb site other www.nfdoi.com is down EXCEPT the last one I published. I have made a mess of things and would appreciate any help.
Don't work:
http://web.mac.com/daviddawley/FuzzyLlamaJuniorOptimist.com
http://web.mac.com/daviddawley/pAwesomeProductions.com
Works:
http://web.mac.com/daviddawley/Optimist_View/OptimistView.com/OptimistView.com.h tml
========= PLEASE USE THE SPACE ABOVE TO DESCRIBE THE ISSUE BASED ON THE QUESTIONS BELOW =========
1. What version of iWeb are you using to publish to .Mac? iLife 08
2. When did you first notice this issue? After publishing a few sites.
3. What happens, including any error messages, when you try to publish your site?
--------------------- Additional Info -------------------------
Alternate email address : [email protected]
OS Version : Mac OS X 10.4.10
Browser Type : Safari 2.x
Category : I can't publish to .Mac from iWeb
Connection Type :Other
TrackID: 4154168Just got off the phone with Apple Support. There procedure was the following:
1. Go to the Apple TV, select settings, general and scroll down to reset.
2. Select reset and then select reset all
Apple TV will go through a restart after the reset and you will have to select your network then log in with your network or Airport Express password. You will then have to turn on home sharing and It will then ask you for your Apple ID for the iTunes store and then the password. At this point you may not see your library, because the Apple TV wants you to turn on home sharing on your home computer that is hosting the movie library. Turn off home sharing on that computer, restart iTunes and turn on home sharing again. After this is done you should be able to see you library listed under the computer.
After going through these steps, when I select an HD movie from my iTunes library the movie comes up after about a 5 second delay.
Hope this helps! I am back up for business. -
Imac slow and Freezes PLEASE HELP!
PLEASE HELP!!!
Hello i have and imac G5 i bought it in about june of 2005...
It was running very slow and always freezing and then i upgraded the RAM to 1gb
and it started working much better. then i upgraded to OS Leopard andalso pro tools LE 7.4
and since then has been performing slow and freezing all the time. ai recently added another gig of RAM just to see if that was the problem , but it seems to be working just as slow. Does anybody know what it might be. Its a 1.6 GHZ power PC G5 and has a 80GB HD and have about 20 GB free so i dont think thats it. Please let me know if any of you have had this problem or know how to fix it thanksExcept for the keyboard & mouse, disconnect all devices from your computer.
Repair your disk from your System DVD.
Repairing permissions from the Tiger or Leopard DVD
Boot up from your Tiger or Leopard Install DVD while holding down the "c" key.
Select the language you wish to use, and then choose "Disk Utility" from the menu bar.
Your HD should appear in a panel on the left hand side of the window which opens. Select it and then click on the "repair disk" button in the right hand section of the window.
If Disk First aid is able to complete the repair now click on the "Repair permissions" button.
Once this process has been completed restart your computer.
===============
Get a larger HD
===============
Use Software Update to update your OS to OS 10.5.6.
Afterwards, repair permissions & restart your computer.
Your system info confirms you are still using an outdated version - OS 10.5.4.
Maybe you are looking for
-
Application Builder for labVIEW 7 Doesn't support any report generation function
I'm Using LabVIEW 7.0 to build an application My Application is exporting data to an excel report. the vis were working great until i tried to creat an .EXE file. The application is working fine but when i try to generate the report nothing happens.
-
Transfer contacts from samsung to iphone5 - what a mess
Hi, I had a Samsung Stratosphere until I purchased the iphone5. Immediately after the purchase, the technician transferred my contacts to my new phone. During the transfer my contacts seem to have come apart. For example, now my contact lists is a co
-
I browse the Mail icon of my Iphone 4 and want to get emails but suddenly the screen bounced back to the front page and cannot entered to the screen I usually to get emails. Tried many times and rebooted the Iphone have the same result. Can you help
-
Personas: is it possible to extend the Personas UI controls?
Hi Personas experts, Personas offers some UI controls, such as Transaction Button, Script Button, Label etc. But they are quite few. Can anyone help the following questions? 1: How to extend Personas to use more UI controls? Would it be possible to a
-
can i have mape on a c1-01?