E2500 constant connectivity failures when secure wireless configured

My E2500 constantly drops connectivity (wired and wireless) when secure wireless is configured through the Linksys Connect software. The problem doesn't happen if the router is left unsecured.
Router Firmware: 3.0.00 build 6.
ISP: Comcast cable
Cable modem model UBEE D3.0
I use a mix of wired and wireless - the PCs are wired and the tablets and phones use wireless connections. The laptop uses wired at the desk and wireless elsewhere.
When I first got the router and used Linksys Connect to configure, the connection was moderately stable for about a week, then started dropping frequently. Recycling the modem and resetting the router to factory defaults stabilized the connection.
Today I re-ran the Linksys Connect software to configure secure wireless for my wireless devices, and the intermittent connectivity problem came back immediately - I couldn't get more than a minute or two online without the connection dropping out.
I don't like running without secured wireless connection, but I don't see an alternative.

Wireless Configurations
What wireless modes are you using?
2.4Ghz and 5Ghz routers: Try single mode G or N or mixed G and N on 2.4Ghz and single mode N or Mixed on 5Ghz?
Channel Width set for Auto 20/40Mhz or try 20Mhz only.
Try setting a manual Channel to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear. 13 for EU regions. Try channel 48 or 149 on 5Ghz. http://en.wikipedia.org/wiki/List_of_WLAN_channels
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=f2625b15a5d7454b8e7fafbe65d5aa63_4009.xml&pid=80&r...
What security mode are you using? Preferred security is WPA-Personal. WPA2 Only. http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=8ce9e83bd3784001aee72da7f1ef48e8_Changing_the_basi...
http://kb.linksys.com/Linksys/ukp.aspx?pid=80&vw=1&articleid=19073
What wireless devices do you have connected?
Ensure any devices with WiFi adapter drivers are updated.
Any 2.4Ghz or 5Ghz cordless house phones or WiFi APs near by?
Any other WiFi routers in the area? Link> Use http://www.techspot.com/downloads/5936-inssider.html to find out. Use v3. How many?
WMM Support must be enabled for single wireless N mode to function.
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&articleid=5471
Router Placement
Forum User - "Well I feel really dumb. After moving the router away from other electronic devices my speeds are back to normal. Just a heads up for anyone experiencing slow speeds, you might want to move it away from other electronics and see if that helps."
3-6' feet minimum safe distance between devices.
Placement on main level floor and central in the building and WELL ventilated is preferred. Not in basements or closets as building materials, or near by electronics devices could interfere or hinder good signal propagation.
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=d9a3b1b2039741948a2365b053a93ea8_3759.xml&pid=80&r...
http://www.smallnetbuilder.com/wireless/wireless-basics/31083-smallnetbuilders-wireless-faq-the-esse...

Similar Messages

Connection failure when connecting to the net with...

I hope someone can help me. I have got Nokia PC suite on my PC. I often use it to connect to the net. Just recently I had a few viruses on my pc and now since they have been cleaned off I keep getting a connection failure when I try to connect. I have tried uninstalling and reinstalling my software but nothing seems to help. I know it is something to do with my pc as I have tried four different phones that do work on other pc's, just not this one.
I have checked to make sure all the modem settings are right and that the phone is detected as a modem.
What should I try that might help solve this??
Thanks
Katherine

Make sure you have entered the access point in the one touch access settings, enter the settings maually and try to connect.
If a reply has solved your problem click Accept as solution button, doing it will help others know the solution. Thanks.

HP Deskjet 3050 - Unable to connect to WPA secured wireless network

Hello,
My first post here so please excuse any faux pas on my part. I bought this HP Deskjet 3050 a week ago and have been waging war with it ever since. I'd be really grateful if someone could possibly advise on how I can resolve this.
I am unable to connect the printer to my secured wireless network, even though other computers, cell phones, etc. are connected without issue. I have tried WPA, WPA2 and WPA2-Mixed security modes with the same failure. Specifically, the connection wizard reaches 66% and then displays the error that the wizard is unable to find network/printer. If I disable the security, the printer connects fine.
I'm using a Linksys WRVS4400N router with firewall and associated firewall settings disabled. The router is broadcasting on 802.11G/N mixed mode.
I'm installing the software supplied on the setup CD on a Windows XP SP3 system. I have confirmed that the network the PC and printer are connected to are the same.
A question as well, if I may: I haven't tried these drivers yet but I see there are updated drivers for the printer dated 14/12/2010. The release notes indicate improved networking, but don't elaborate beyond this. Does anyone know if there was a known problem with connecting to secured networks that has now been fixed?
Finally, just a note that I'm partially sighted and am using a screen reader on all systems. I'll try my best to be as helpful as I can but please do excuse me if I occasionally can't find settings, etc. on screen and need a bit more detailed help.
Thanks in advance for your help, which I really will appreciated.
Have a pleasant day,
All the best for now and take care,
Hussein.
It's not the fact it can't be done, it's the fact it hasn't been done, yet.
This question was solved.
View Solution.

HI,
firstly, apologies for the delay getting back to you. Poor health has meant I've had little time nor inclination to do much on the computer side of htings.
Anyway, I'm please to say the problem with the HP 3050 failing to connect to my network is now solved. It seems to be a bug with the setup software, and that seems to include the latest version posted Dec 2010.
To resolve the problem, I did the following:
1. Disable all security options for the network, so it's just an open network.
2. Connect the HP 3050 to the network using the setup wizard. This time it connected OK for me.
3. Locate the printer's IP address. I used the client list table accessed through my router's interface. You may be able to get this through the printer's on-screen menu, but as I'm partially sighted, this wasn't an option for me.
4. Log into the printer's control panel at http://ip.address.of.printer e.g. http://192.168.2.108
5. Under the advanced options, configure the settings for the network, including security protocol and passphrase. Remember to enter the SSID of the network exactly as configured on the router.
6. Apply the settings and log out of the printer's control panel.
7. Log back into the router's control panel and re-apply the security options. Be sure that they match those match those entered for the printer.
Hopefully this will be of use to others in the same position.
Thanks again for your time.
Best,
H.
It's not the fact it can't be done, it's the fact it hasn't been done, yet.

Unable to connect to a secure wireless network - Event ID: 8002 Task Category: AcmConnection..., Event ID: 11006, Event ID: 11006

Hi,
I have a Dell Latitude E6440 running Win 7
Enterprise 64 on a domain. It will connect to any unsecured network, and it can see the secured network in the list when I click the wireless connection icon on the system tray. When I go to manage wireless networks, the secured network does not show
up (and thus, I cannot delete the network to try to re-add it). Normally, we would add the secure network here. I click Add, give the name in the correct syntax, add the needed information (WPA/2-Enterprise, EAS or TKIP), and hit Next, it immediately returns
with "An unexpected error occurred". A similar thing happens when I hit Connect from the list of available networks that pops up when I open the system tray icon: it says it was unable to connect, when I hit troubleshoot, it says that it could not
identify the problem. The event log shows the error below. I haven't been able to find any resolutions here or elsewhere that address the fact that I can connect to unsecured wireless networks, but not secured wireless networks.
Other notable troubleshooting steps:
Uninstalled/Reinstalled wireless adapter with the latest driver
Other laptops are able to access the same secure wireless network
The first WLAN-AutoConfig error in the event log was Event ID: 12013, attempting a 802.1x authentication. Then Event ID: 11006; stating "Explicit Eap failure received". After a few days of alternating all 3 errors, they started to only error on
Event ID 8002.
Log Name: Microsoft-Windows-WLAN-AutoConfig/Operational
Source: Microsoft-Windows-WLAN-AutoConfig
Date: 6/4/2014 11:53:55 AM
Event ID: 8002
Task Category: AcmConnection
Level: Error
Keywords: (512)
User: SYSTEM
Computer: [COMPUTERNAME.DOMAIN]
Description:
WLAN AutoConfig service failed to connect to a wireless network.
Network Adapter: Intel(R) Centrino(R) Advanced-N 6235 Interface GUID: {f27af762-dff8-4927-84e0-7f4ade30dcc9}
Connection Mode: Connection to a secure network without a profile Profile Name: [SECURE NETWORK NAME]
SSID: [SECURE NETWORK SSID]
BSS Type: Infrastructure
Failure Reason:The specific network is not available.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-WLAN-AutoConfig" Guid="{9580D7DD-0379-4658-9870-D5BE7D52D6DE}" />
<EventID>8002</EventID>
<Version>0</Version>
<Level>2</Level>
<Task>24010</Task>
<Opcode>191</Opcode>
<Keywords>0x8000000000000200</Keywords>
<TimeCreated SystemTime="2014-06-04T16:53:55.956762800Z" />
<EventRecordID>1475</EventRecordID>
<Correlation />
<Execution ProcessID="432" ThreadID="5348" />
<Channel>Microsoft-Windows-WLAN-AutoConfig/Operational</Channel>
<Computer>[COMPUTERNAME.DOMAIN]</Computer>
<Security UserID="S-1-5-18" />
</System>
<EventData>
<Data Name="InterfaceGuid">{F27AF762-DFF8-4927-84E0-7F4ADE30DCC9}</Data>
<Data Name="InterfaceDescription">Intel(R) Centrino(R) Advanced-N 6235</Data>
<Data Name="ConnectionMode">Connection to a secure network without a profile</Data>
<Data Name="ProfileName">[SECURE NETWORK NAME]</Data>
<Data Name="SSID">[SECURE NETWORK NAME]</Data>
<Data Name="BSSType">Infrastructure</Data>
<Data Name="FailureReason">The specific network is not available.</Data>
<Data Name="ReasonCode">163851</Data>
<Data Name="ConnectionId">0x6</Data>
</EventData>
</Event>

check this article:http://technet.microsoft.com/en-us/library/cc735927(v=ws.10).aspx
also could contact your domain administrator to ask for help.

Connectivity failure when authorizing

I've been trying to authorize my computer. First time id and first time on this computer. I consistently am met with a "connectivity failure" message despite the fact that my internet connection is working fine. I am able to login to the adobe website in order to post this - why can't I authorize my computer?

Hallo,
ich habe die letzten beiden Tage mit diesem Problem verbracht. Ich habe beim Chat nachgefragt, im Forum geschaut und mit dem Support telefoniert. Alles erfolglos. Dann habe ich den Virenscanner ausgeschaltet und die Firewall auch! Als es dann immer noch nicht ging, habe ich gemerkt, dass ich noch einen zweiten Virenscanner auf dem PC hatte. Nachdem ich diesen deinstalliert hatte, hat die Authorisierung geklappt.
Ich hoffe, das hilft dir weiter!
Viele Grüße und viel Erfolg!

Not able to connect on my secured wireless network

I am having WRT54G2 router and i configure my router for my home. I configured it as secured network. I have a laptop (IBM Thinkpad R52). But i am not able to connect my home wireless secured network. When i try to connect any other unsecured (open to all) network from my laptop it allows me. For any secured network it says Acquiring Network address. What should I do?

What encryption are you using?
What operating system are you using?
For WEP, you must enter WEP "key 1" (found in the router) into your computer, not the WEP password or passphrase.
For WPA or WPA2, you must enter the key (sometimes called password or passphrase) into your computer.
Note that WPA2 (= WPA with AES) requires that you upgrade Windows XP to SP3. If you have not done this yet, do this now. Note that Windows Vista already works with WPA2.
If you still have trouble connecting, in the computer, temporarily disable your software firewall, including Windows Firewall, and see if that helps.
If you still have trouble, download and install the latest driver for the wireless adapter in your computer.
Message Edited by toomanydonuts on 05-30-2008 01:22 AM

Constant connection failure

Hi all
I have an old 1.0-type hub which I've been using for the last four or five years and until recently it has given me no trouble. However for the past week it has been failing to connect when I switch on my laptop. The Broadband Help utility kicks in and checks the connection, then advises me to restart the hub (which in this model involves unplugging it for thirty seconds then waiting until the lights come back on). The connection is then made and all is well. The following day, however, I have to go through the same procedure. Has anybody else come across this? Do I simply need a new hub?
GordonD
Edinburgh

Thanks for the advice.
Details from the hub stats page:
My broadband connection
Your broadband line is connected.
Broadband connection details:
Downstream
10,152 Kbps
Upstream
1,227 Kbps
Connection time
0 days, 4:03:34
Data transmitted
5.30 MB
Data received
21.58 MB
Broadband user name
[email protected]
My telephones
Current settings for the telephones and handsets connected to your BT Home Hub.
Calls to:
Will ring:
Status:
BT Hub Phones and Phone socket
My landline
None of the Hub Phones
My home network
Devices connected to your BT Home Hub.
Wireless:No devices detected
Ethernet: TOSHIBAPC
Ethernet: GordonPC
USB:No devices detected
Not sure why it still lists a Toshiba PC in there as that was my previous laptop which hasn't been used for about three years.
I can't do the socket test as I don't have that type of wall socket. I am an ex-BT employee (in the office, not the engineering side) so I'm aware of these tests but as I say can't carry them out myself.
As I said, I don't have a problem once the connection has been made; it's just irritating to have to restart the hub every day.
GordonD
Edinburgh

HT1657 I just got an iPad and rented a movie from iTunes. I am connected to my secure wireless wifi. I have downloaded the movie and received the email confirmation of purchase. I cannot now watch my movie. What must I do?

I got a new iPad,rented my first movie from iTunes, paid for and downloaded it. Now I want to watch but cannot.clicking on the movie in iTunes showsit downloaded. Message in email shows it has need paid for. I am connected to secure wifi. How do I watch my rented movie?

You're welcome. Glad you got things sorted out.

How to fix iWeb Test Connection Failure when i have correct login information??

I have been using iWeb and updating my site with no issues. Suddenly I can not connect to the FTP and when i test the connection with the correct login information i get a message that a connection could not be established. I'm not real familiar with how iWeb works to post to our website so i'm confused on why it is not connecting. Any help would be great!

Sometimes the built in iWeb ftp does this. You can test to see if it is an iWeb problem by perhaps trying a dedicated ftp programme instead such as the free Cyberduck. Download Cyberduck and then you'll have to publish your website from iWeb to a local folder and then use Cyberduck to connect to your host with the same log in details and see if this works. If Cyberduck can connect to your host/server, then the problem is with iWeb.

Connecting Nokia N900 to secure wireless

I can't get my N900 to connect to any secure wireless!!! (where psw is required)
I just downloaded the latest firmware - software - etc from nokia website hoping this would solve the problem but it doesn't!!!
The nokia just gives me two options to be connected:
Push a button on wireless station to initiate easy setup process and tap "done"
Pin method: Enter the following digits on wireless station and tap "Done".
My router doesn't have any "button" for this, nor can I in its setup introduce the pin.... and EVEN IF THIS WOULD WORK... what would I do if I want to connect from anywhere else and cant access the router to change its configuratino or "press a buton" on it???
What can I do to override this useless connection setup of my nokia?????

I had this problem the other day when I was at a friends house. Everyone else with an Iphone, there were 4 or 5 Iphones, were connected to his wireless but my N900 wouldn't connect and kept asking for the pin code for the wireless.
Has anyone else had this problem when there has been a lot of Iphones?

Secure connection failure in browser for https sites

Recently I kept getting the error message "Secure Connection Failure" when using Firefox to go to https sites. I had a similar problem when I tried using Safari to connect to https sites.
I fixed the problem by opening System Preferences > Parental Controls > selecting the appropriate User (as long as you have administration rights) > selected Allow unrestricted access to websites (by default Try to limit access to adult websites automatically is selected).
Once I checked unrestricted access I was able to go to the https sites I wanted, which were my bank's site and the Firefox homepage for FAQs. Then I went back and checked "Try to limit ...". That brought back the error message again so I checked "Allow unrestricted access ...".
The issue may have arisen because I downloaded a system security update a few days ago. Perhaps it reset the Parental Controls default.
It would be good to block adult sites but the alternative seems to be to customize in Parental Controls the sites that are OK. This would be a tedious job because so many sites are https eg this site.
I no longer have a problem but thought this might help others.

Strangely, I noticed a couple of https sites I had trouble logging into from a link inside a https site.
In System Preferences I went to Accouns and for myself unchecked "Enable parental controls".
I was then able to log onto the the https site.

ACE showing many connection failures on server farm

I just upgraded my ACE blade from A2(1.0 to A2(1.5a). After the upgrade I'm seeing an enormous amount of connection failures when I run the command show server xxx. Everything appears to be running fine. I can get to the web servers. I found an old posting and they reference Bug CSCsh1478, but when I looked at this bug the problem was corrected in version A2(1.0). Any ideas of what's going on?
Thanks
Mike

you will need to take a sniffer trace to see if there are any un-answered SYN or RST from the server.
Gilles.

[svn] 4258: Bug: LCDS-522 - Add more configurable reconnect handling for connecting up again over the same channel when there is a connection failure /outage.

Revision: 4258
Author: [email protected]
Date: 2008-12-08 16:33:17 -0800 (Mon, 08 Dec 2008)
Log Message:
Bug: LCDS-522 - Add more configurable reconnect handling for connecting up again over the same channel when there is a connection failure/outage.
QA: Yes
Doc: No
Checkintests Passes: Yes
Details:
* Updates to configuration handling code and MXMLC code-gen to support new long-duration reliable reconnect setting.
Ticket Links:
http://bugs.adobe.com/jira/browse/LCDS-522
Modified Paths:
blazeds/trunk/modules/common/src/flex/messaging/config/ClientConfiguration.java
blazeds/trunk/modules/common/src/flex/messaging/config/ClientConfigurationParser.java
blazeds/trunk/modules/common/src/flex/messaging/config/ConfigurationConstants.java
blazeds/trunk/modules/common/src/flex/messaging/config/ServicesDependencies.java
blazeds/trunk/modules/common/src/flex/messaging/errors.properties
Added Paths:
blazeds/trunk/modules/common/src/flex/messaging/config/FlexClientSettings.java
Removed Paths:
blazeds/trunk/modules/core/src/flex/messaging/config/FlexClientSettings.java

Remember that Arch Arm is a different distribution, but we try to bend the rules and provide limited support for them. This may or may not be unique to Arch Arm, so you might try asking on their forums as well.

HP Wireless Printers cannot connect to WPA2-secured WiFi networks with Cisco/Meraki WAPs

In the last two months, I've had the displeasure of working with two very different HP printers and attempting to make them work on a WPA2-secured wireless network. All attempts to authenticate fail with "invalid phassphrase".
I'm not the first person to encounter this, it's a problem with many different HP wireless printers (I just happen to have physical access to the OfficeJet Pro 8610 & Deskjet 3511).
My equipment is a Cisco ASA 5505 Firewall running ASA 9.1x & Cisco Aironet 1142 running IOS 15.3.x.
What does work on the WPA2/AES SSID: Apple MacBook Air running OSX 10.10.2, Three Windows-Based laptops running Windows 8.1 Update 1, an iPhone 5s, Three Windows Phone 8.1 devices, Roku 2, PlayStation 4, PlayStation 3, Sharp Aquos TV, Amazon Streaming Stick, and an Android Tablet (Jellybean). Basically, everything.
What does not work on the WPA2 network: OfficeJet Pro 8610 & Deskjet 3511.
To test the theory there is a problem with HP's implementation of WPA2 with regard to Cisco Aironet IOS, I built out a second SSID that only works in WPA/TKIP mode. This solution works. Both HP printers will join the WPA/TKIP network.
So, I'm able to demonstrate there is a certain connectivity issue. When i look at AAA Debug on the WAP's console, I can observe the HPs attempt to authenticate "Bind I/F" on the WPA2 SSID, however they do not achieve authentication and do not pass the AAA phase. However, on the WPA SSID, they bind and authenticate successfully.
To help illustrate this, here is my WAP running config. It's about as simple as it can get. There is no relevant MAC filtering or ACLs bound to any interface. Noting that I have an ACL on remote access to the WAP (i.e. Locked down to SSH, disabling telnet). The main point being that the ASA firewall is not a factor in this problem as the issue is at the WAP before WPA2 authentication can complete, therefore the printers never reach the network / when the printers connect to the WPA network, the operate fully & correctly.
If anyone at HP can indicate why this particular config is somehow improper or broken, that would be fantastic. There should be no reason why Cisco / Meraki WAP owners have to lower wireless encryption standards just for a printer, be forced into wired, create separate SSIDs with lower encryption specifically for a device.
Building configuration...
Current configuration : 6064 bytes
! Last configuration change at 12:46:47 UTC Fri Aug 20 1993 by admin
version 15.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname 10-10-50-1
logging buffered 1024768
logging rate-limit console 9
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
no ip source-route
no ip cef
ip domain name freedom.local
dot11 syslog
dot11 vlan-name inside vlan 50
dot11 vlan-name inside-wpa-only vlan 70
dot11 ssid inside
   vlan 50
   band-select
   authentication open
   authentication key-management wpa version 2
   mbssid guest-mode
   wpa-psk ascii 7 xxxxxx
   information-element ssidl
dot11 ssid inside-wpa-only
   vlan 70
   band-select
   authentication open
   authentication key-management wpa
   mbssid guest-mode
   wpa-psk ascii 7 xxxxxx
   information-element ssidl
dot11 band-select parameters
   cycle-count 3
   cycle-threshold 200
   expire-supression 20
   expire-dual-band 60
   client-rssi 75
dot11 wpa handshake timeout 500
dot11 network-map
username ADMIN privilege 15 secret 5 xxxxxx
ip ssh version 2
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 50 mode ciphers aes-ccm
encryption vlan 70 mode ciphers aes-ccm tkip
ssid inside
ssid inside-wpa-only
antenna gain 0
mbssid
speed basic-1.0 basic-2.0 basic-5.5 basic-11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel 2412
station-role root
l2-filter bridge-group-acl
interface Dot11Radio0.50
encapsulation dot1Q 50 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.70
encapsulation dot1Q 70
no ip route-cache
bridge-group 70
bridge-group 70 subscriber-loop-control
bridge-group 70 input-address-list 700
bridge-group 70 output-address-list 700
bridge-group 70 spanning-disabled
bridge-group 70 block-unknown-source
no bridge-group 70 source-learning
no bridge-group 70 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface GigabitEthernet0.50
encapsulation dot1Q 50 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.70
encapsulation dot1Q 70
no ip route-cache
bridge-group 70
bridge-group 70 spanning-disabled
no bridge-group 70 source-learning
interface BVI1
mac-address xxxx.xxxx.xxxx
ip address 10.10.50.1 255.255.255.0
no ip route-cache
ip forward-protocol nd
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip route 0.0.0.0 0.0.0.0 10.10.50.2
logging history size 100
access-list 111 permit tcp any any neq telnet
bridge 1 route ip
line con 0
access-class 111 in
line vty 0 4
access-class 111 in
length 0
transport input ssh
line vty 5 15
access-class 111 in
transport input ssh
end

I get the same behavior with a laserjet m451nw. I need to enable tkip to get the printer working, it doesn't support pure aes-ccm (every other device here supports pure aes-ccm, even cheap ones), although it's advertised as working.
The following snippet of config works, but I still think it should work without the tkip "hack".
dot11 ssid whatever
vlan 1
band-select
authentication open
authentication key-management wpa version 2
interface Dot11Radio0
encryption vlan 1 mode ciphers aes-ccm tkip

Ipod touch 1st generation can't connect to my linksys wireless router wr110. THe signal is strong and there is a check mark beside my network name, but when I try to open safari it says "unable to find server".

My friends MacBook connected easily to my wireless, but why not the ipod touch? When prompted for "Password" I enter the security key info and nothing, nadda....zip. The MacBook asks for the "Security Key" info not "Password", like the touch. What's the difference?

Click on the blue arrow to the right of the network name, if IP address starts with "169." ,restart your router. It should connect properly after your router reboots in a minute or two.

E2500 constant connectivity failures when secure wireless configured

Similar Messages

Maybe you are looking for