E2500 guest network

Few questions about the Cisco/Linksys E2500 router. Not sure if this is the right forum, please let me know if there is a more appropriate forum.
1. How can I setup a different wireless security for the main network (WPA2/Personal) and guest network (WEP)?
2. How can I see the DHCP clients connected to the guest network? The router config web interface only shows this for the main network.
3. By default, Cisco Connect uses the same password for the router (192.168.1.1) and the main SSID. Is it possible to go into Advanced settings and change the router password or would that mess up Cisco Connect?
4. The guest network appears as a unsecured network but when you open up a browser to access the Internet, it redirects to the router password page. This is fine for devices that have a web browser facility. But how can I activate the guest network for other devices like, say, a gaming console Nintendo DS, Wii or a Logitech Squeezebox Boom internet radio, Roku media player, etc. They appear to connect to the guest wireless network but are unable to access the Internet.
Thanks

1. The guest network is unsecured like ALL free guest networks from McDonalds to Starbucks. No security is needed or wanted otherwise you would have to enter that security password all the time.
2. I don't think you can. You know who is on your Guest network because they are in the house and you gave them the password at the browser prompt.
3. If you use the web browser to do anything the Cisco Connect will not work anymore. Go into the settings and look around to find out all about your router. You can always reset everything and start over.
4. No, the Guest network is for computers only.

Similar Messages

E2500 Guest Network Bandwitdh Throttle?

Greetings,
I currently use a E2500 router for my home network. I have setup the Wireless guest Network for my downstairs Tenant while he is out of work so he can still have some internet. The problem however is that often the guest network will take up 90% of my 55mb/sec bandwidth, leaving none for the primary network. Is there a way for me to Throttle the amount of bandwidth the Guest network can use? Say alot 10mb/sec for Guest access only, and leave the rest for our main network?
Any help with regards to this would be very helpful as even though my tenant is down on his luck, if this continues I'll have to remove the guest network completely.
Thank you.

it's ashame theres no way to restrict the Guest Network, I would think thats an excellent addition to Future routers.
I know he was using about 90% of the bandwidth by the following: we have 3 computers on the main network, 2 wired, 1 wireless. i have a bandwidth download ability of ~55mb/sec with him online on the guest network my wired main computer was suddenly getting ~0.5mb/sec. I unhooked the other wired computer and the wireless devise on the main network and re-tested and still only had 0.5mb/sec
so the guest network had takin over 90% of the net and the router was not re-assigning equal priority to both networks. I had to turn off the guest network and then back on 30seconds later, and I was suddenly back up to full bandwidth.

Linksys E2500 - Guest Network help

I recently purchased a Linksys E2500 router and currently have it set up with my main network and a guest network. Everything works as normal, except my devices are not prompted to enter the guest password every time. I logged on the guest account (and entered the password) the first time I set up the router, and then logged back onto my regular network. I then logged off the regular network and went back to the guest network and it operates as if I were still on the regular network, and doesn't prompt for a password and allows me to go to websites as normal. I was under the impression that it wouldn't save the password and would be required EVERY TIME a user logs on, not simply once and then in the future it never asks again. If anyone could help me with this issue I would be really appreciative. Thanks!

Let me know the current firmware version in the Router? If the firmware in the Router is an older version then upgrade it with the latest one which can be downloaded from the Linksys/Cisco website. After successful firmware upgrade you need to reset the Router. It is recommended to reset the router once. Steps to reset the router:
Push the reset button on router for 30 seconds, turn off the router wait for 30 seconds and then power it on. Power light should blink when you perform the reset process.
After reset, reconfigure the router and then check the connectivity status of the Guest Network..

E2500 guest signon

I have a e2500 installed in a reasturant for customers to have web access via the guest feature. The router gives 2 names ie network & network.guest.
Customers are confused and often try to use the non guest signon which does not work because of password. I have read that you cannot change just the guest name.
If I turn off broadcast ssid, will it prevent broadcast of both?
If so I would appreciate it solutions someone could offer.
Thanks

Hi,
I had that question in my mind when I used e2500 router. I discovered that for e2500 router’s guest network, you cannot change the guest access name or SSID. I think it is a product design. So if you decide to disable the SSID broadcast of your main wireless signal, make sure to connect all wireless devices that are officially part of your main network first. Then you may disable the SSID of the 2.4 Ghz and 5 Ghz. If you decide to add new devices or pc on your network, then you just have to enable the SSID broadcast. Just inform your customers to connect to the one that has dash guest” network” at the end of name.

I cannot add a Wi-Fi guest network. Gone to Utilities Airport Utilities and all get is an image/browser of my Airport Extreme. Looking for the browser which has the title Wireless but cannot find anywhere. I need help?

I cannot add a Wi-Fi guest network. Gone to Utilities>Airport Utilities and all I get is an image/browser of my Airport Extreme. Looking for the browser window which has the title Wireless but cannot find anywhere. What am I doing wrong?

Open AirPort Utility. The first screen looks something like this:
Click on the AirPort Extreme and another screen will appear. Click Edit, then the window with the Wireless tab will appear.
If you do not see these screens, you will need to start over and configure your AirPort again.

Airport Extreme 802.11AC + 5th Gen and guest network access

I have the current gen Airport Extreme 802.11AC with a 5th Gen extending the network. With this setup, I am unable to login using our guest network setup. I have tried using guest network with a password and one without but its the same results. When a guest logins, it stuck attempting to login with no error messages.
So is it possible to have this configuration and still have guest network access?

Please review what I said originally.......that the guest network function on the AirPort Extreme is designed to work with a simple modem......so the AirPort acts as the main router for the network..
Another way of saying the same thing is that the AirPort needs to be "in charge" of your network for the guest feature to work correctly. The AirPort cannot be in charge if it is connected to another device that is already configured to be the main router on your network.....your Actiontec modem/router.
The Actiontec device combines the functions of a separate modem and a separate router in one package. This type of device is known as a modem/router, or also known as a gateway.
Some folks call a modem/router or a gateway......a modem. So, things can get confusing.
I do not know if it is possible for the Actiontec device that you have to be configured to act as a simple modem.....so the routing functions of the device are completely turned off. (Turning off the wireless on the Actiotec does not turn off the routing function).
If you turn off the wireless on the Actionec, it becomes a modem and a wired router. And that wired router is still in charge of your network.
The guest network feature will not work correctly unless the AirPort is in charge of your network.
My suggestion was for you to ask your Internet Service Provider (ISP), if they could supply you with a simple modem. That is all that you need. You don't need two routers....and the Actiontec that you have now is not allowing the guest feature to work correctly.

Cascading EA4500s and Guest Network access

Hi, I hope esomone can help me here. I've got two EA4500 routers connected via ethernet. The primary router has DHCP enabled and the secondary has it disabled. IP address of primary is 192.168.1.1 and the secondary is 192.168.1.2.
I have set up guest access on both routers however only the primary router allows users to connect. When out of range of the primary router but in range of the secondary router the network is visible but when you try to connect to it, it only gives limited or no connectivity message and can't connect to the internet.
Is it possible for the guest network access to follow the same pattern as the secure network, i.e. the same network throughout the house?
Regards
Jon

Cascading two routers should have correct parameters set. For instance, the Ethernet port of the secondary router should be connected to the ethernet port of the primary one, and the DHCP should be disabled on the second router. The ip address you've set are correct for the both routers. This thing shoud be done if the connection is LAN to LAN.
By the way there are two types of cascading: Click here for info!
For the Guest Network:
Guest Network would only work if the the DHCP is enabled on your router. It means to say that on the type of setup you're doing which is LAN to LAN (DHCP disabled on the second router), Guest network would not work on the secondary router. If the connection is LAN to WAN, then both of the router should have Guest Network working.

How do I configure Guest network to access ethernet wired printer?

I have a wired/wireless network with a new dual band AEBS. The AEBS is connected to a Cisco router, which in turn sends it's connections to various wall-plates in our home. One HP 4110 printer is wired via it's ethernet port, one Mac Mini (OS 10.6.2) is hard wired also. The dual band AEBS 5 GHz network is used for our newer laptops, and the 2.4 GHz network is used for a G3 Firewire PowerBook (now don't make fun... it was the best there was at one time) running OS 10.4.11.
The PowerBook cannot access the printer that is hard wired via ethernet cable to the network. How do I get the PowerBook on the "Guest" network to access the printer?
I tried searching these discussions, but can't find an answer to my specific issue. Any help is appreciated.

Since you have a simultaneous dual-band AEBS, why not connect your PowerBook G3 to the non-Guest 2.4 GHz network created?
Can I take an AEBS that is a couple of years older (I have a couple of the flying saucers around here somewhere), wire that to an available ethernet port on the LAN, and then connect the older PowerBook G3 to that older AEBS wirelessly?
Sure
If so, will that arrangement slow down the entire system?
No
If that won't work, and I connect the PowerBook G3 directly to an ethernet port, will that slow down the other wireless computers?
Yes you can connect your PowerBook G3 via Ethernet. That would have no effect on the wireless computers.

How do I add a guest network to existing airport extreme configuration?

I have an existing Airport Extreme configuation in my home Wifi network and I want to add a guest access point. When I open the recently updated airport utilities, the screen no longer looks the way it used to, with the side bar on the left and my devices listed there for me to select (I also have an Airport Express). I used to be able to select the Airport Extreme from the left side bar, then hit continue to change any settings. Well now, since it updated, the screen looks different, with internet at the top, pointing to the Airport Extreme, then the Airport Express. When I select the Airport Extreme, it no longer gives me the option to change the settings for it, which is where my problem lies! Any help? I know it's probably something very simple that I am missing, but I'm at a loss.

Why would I download a lower version of AirPort Utility?
To gain more functionality.....since AirPort Utility 6.0 is otherwise known as "AirPort Utility Lite" on the forums. It's a "first try" for Apple with a new look. While it does look nice, it has been downgraded as far as the features are concerned.
For example, if you open AirPort Utility 5.6 and click on the AirPort Extreme on the left, your Generation version will be displayed on the right side of the page. There are many more advanced settings available in AirPort Utility 5.6 as well...that are not available on 6.0.
But, you don't have to install AirPort Utility 5.6 if you don't want to. I suggested it because it offers more features and will also look exactly the same as the AirPort Utility that you have used previously.
If your AirPort Extreme is in Bridge Mode, this indicates that you have another device...probably a modem/router....which is acting as the main router on your network. Bridge Mode is the correct setting for the AirPort Extreme in this case.
If you can post back with the make and model number of your "modem", we can check to confirm.
Unfortunately, the Guest Network cannot be enabled unless you configure the AirPort Extreme to be the "main" router on your network, which is likely not possible. If you try to configure the AirPort Exteme otherwise, you will receive error messages and the network will not function correctly.

How do to set up time limits on a guest network

I have a new generation Airport Time Capsule and I have set up a Guest Network for my kids but I would like to set up time limits on the Guest Network also, is there a way to do it?

It is not possible to set up specific time limits for the Guest Network as a whole, but it is possible to set up individual time limits for each device that will be connecting to the Guest Network.....and, also the main network for that matter.
If you can provide us with some more specifics on what you are trying to accomplish, how many devices will be involved, etc.......that will help us craft our answer to provide accurate information.
Meanwhile, if you want to take a look at the general settings in Timed Access....
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the Time Capsule icon, then click Edit
Click the Network tab at the top of the screen
Enter a check mark in the box next to Enable Timed Access
Click on the Timed Access button
Click Cancel to avoid making any changes to your current setup

Hi. Does anyone know how to delete my guest network from the list of network choices that everyone in the neighborhood sees when picking a network? Followed helpful suggestions on this site to delete the netwk but it still appears. Appreciate any help!

Hi. I'm trying to make my guest network disappear from the list of network choices that appears to everyone in the neighborhood. Even though I followed the great suggestions on how to delete the network, it's still appearing in the list that everyone sees. It has my name and would prefer to get rid of it.
Please help! Many thanks!

Thank you for not only the tip but also especially the research showing that for anybody other that those using Wi-Fi for the first time the network wouldn't disappear. I wanted it to disappear for everyone so.....I finally solved it by resetting the Airport Extreme to the factory settings and starting over from scratch! It worked! Yay!!!!!
So, for everyone that has had this problem (and I've read many of the same complaints in different places on the Internet), you must go into Airport Utility and check the box stating that you want to reset it to the factory settings. Do not do it with a paper clip and the reset button on the box; I tried that first and it did not work. You must reset it via the Airport Utility. Then just start over and you will have the choice to NOT check the box to Enable Guests. If you want to enable guests, just be sure not to use your name or you're back to the same problem. Apple is so great with everything...wouldn't it have been so easy for them to just put this in the manual somewhere????? Thanks for all your help. Hope this helps others!

How can I delete the guest network from my airport. It was fine until the last update. It says my whole name's guest network which I do not want everyone seeing. There is no guest network setting in my airport utility.

How can I delete the guest network from my airport. It was not showing up until I recently upgraded the airport. It now says my name's guest network and I don't like my name showing on the available network list! I am using a Verizon wireless modem with the wireless feature off.

Open AirPort Utility, go to the Wireless tab and remove the check from the guest network check box.

How can I create a guest network on an airport extreme that connects wirelessly with a Timecapsule

I have a Timecapsule in one place of our house, that is connected to Internet. I need to extend the range of my network: 1. my private network needs to get to a remote location to make connection with speakers (Itunes). for this I need to first extend the range of my private network, because the speakers are too far away from the TC. 2. I need to set up a guest network, but at quite some distance from my TC, in an other part of the house, too far away from the TC (so a guest network on the TC won't do).
For this, upon advice from an apple store, I bought an airport extreme, which I have placed on a location where it can connect to the TC, to extend the private network. On the location of the speakers, I have an aiport express (connecting to the extreme), to play music from Itunes. The setup at this moment is: TC makes connection to internet, and broadcasts a private network. Extreme connects to this private network, and broadcasts it further to the Airport express, that captures it and plays the music. I would now like to create a guest network on the Airport Extreme, while this Extreme keeps on connecting to the private network of the TC and keeps on broadcasting it to the Express. Is this possible? How can I do this? Thanks for the help !

I would now like to create a guest network on the Airport Extreme, while this Extreme keeps on connecting to the private network of the TC and keeps on broadcasting it to the Express. Is this possible?
Unfortunately, the "main" router...your TC in this case....is the only device that can create a Guest Network, assuming that the TC is connected to a simple modem.
Unfortunately again, the Guest Network cannot be extended. Your only real option here is to create a Guest Network on the TC and hope that it will have sufficient coverage for your needs.

Using Airport Express on separate subnet to make isolated Guest Network?

Hi. I've done a search here, I've tried setting this up at my house but haven't figured it out yet.
Friends have Verizon FiOS service. They're using the provided modem as the ethernet router and it is handing out DHCP addresses, and for a number of reasons including their home theater, on demand use, etc., they want to keep the FiOS modem as the router, not an Apple product.
We're using an Airport Extreme and a Time Capsule both in bridge mode to distribute the wireless network and everything works fine. They'd like to add an isolated, unencrypted Guest Network. I know we can't use the Extreme's Guest tab because we're in bridge mode.
But we do have a new Airport Express. It seems like there would be a way to set up a Double NAT on a different subnet and give guest users access to the internet but not to computers, shared volumes, printers, and everything else on the primary, encrypted network.
Is there a way to do this or will every address coming from the FiOS router be on the same subnet? Are there any other horrible consequences from doing this, i.e., the primary network will still operate fine?
If the DHCP range coming from the FiOS router is 192.168.15.001 to 192.168.15.199, do I set the Airport Express IP address manually? To what?
To eliminate the possibility of duplicate IP addresses would you have the Airport Express hand out a small range of IPs on a completely different network area, like 10.0.1.1?
Any other suggestions? Thank you.

I was trying to create a primary and guest network division after the router... such as an unusual configuration in the AEBSn after the FiOS router.
At my home I have my cable modem connected to an AEBSn, which is doing my network's routing. But I didn't set a Guest Network on this AEBSn. I am trying to set up a discrete Guest Network downline from this router. (Which would simulate my friend's installation where they're using a FiOS modem/router all in one and we want to create a discrete Guest Network after that.)
But as I guess you've been patiently trying to get through to me, Bob, whatever outlying separation you may be able to create seems to get put back together at the main router.
For example, today I connected a second AEBSn ("AEBSn Guest") to the LAN port of my primary AEBSn router. I set the AEBSn Guest to create a wireless network, and I set that to be a closed encrypted network called "Test," and I enabled unencrypted Guest Networking as usual and told the AEBSn to ignore the Double NAT error.
With this configuration I am able to get on the open Guest SSID, and internet connection is normal. Between the Guest and the primary encrypted network, printing is broken, iPhoto sharing is broken, and so on, but I still see shared volumes and can log in with authentication.
So I can see why a solution to this may have been elusive.
I don't know much about cable TV's subscription services but I took a peek at the set up pages of the Verizon FiOS router and noted there was a lot going on there. Lots of ethernet and cable IP addresses to Set Top Boxes, etc. Not sure if all this could be recreated within the administration of the Airport Extreme, but I am hesitant to risk messing up the Comcast services which are presently working well.
In terms of zooming out to the big picture... when I invite guests to share my internet service, they're usually doing email and web browsing for the weekend but at the end of their stay they want to print their boarding passes... so despite setting up a guest network I might end up giving them access to the main network anyway.
Thanks for the help, Bob.

Can I set up a default website for my guest network on an EA3500?

Just got a new EA3500, and plan to use its guest network feature to allow Internet access but not access to my LAN. Wondering if I can set it up so that users on the guest network bring up a particular website when they open their browser. I didn't see anything about this in the user's guide or in the forums.

That's actually how Guest Access feature works. You can share internet to your guest/visitors without giving them access to your local network. You may configure the Guest Access settings on the router using Linksys Smart Wifi through the local access interface; check this site for the instructions, http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=b509a1805dd6416ebb0e35a7e5a58937_Configuring_Guest...
Added Info:
Guest Network Frequently Asked Questions
http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=f35bd58fda4148929ac482f3c7968e04_Guest_Network_Fre...

E2500 guest network

Similar Messages

Maybe you are looking for